mfd: Ensure WM831x charger interrupts are acknowledged when suspending

The charger interrupts on the WM831x are unconditionally a wake source
for the system. If the power driver is not able to monitor them (for
example, due to the IRQ line not having been wired up on the system)
then any charger interrupt will prevent the system suspending for any
meaningful amount of time since nothing will ack them.

Avoid this issue by manually acknowledging these interrupts when we
suspend the WM831x core device if they are masked. If software is
actually using the interrupts then they will be unmasked and this
change will have no effect.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

1 files changed, 47 insertions, 0 deletions

diff --git a/drivers/mfd/wm831x-core.c b/drivers/mfd/wm831x-core.c
index da00ca9..1a968f3 100644
--- a/drivers/mfd/wm831x-core.c
+++ b/drivers/mfd/wm831x-core.c
@@ -1494,6 +1494,7 @@ static int wm831x_device_init(struct wm831x *wm831x, unsigned long id, int irq)
 	case WM8310:
 		parent = WM8310;
 		wm831x->num_gpio = 16;
+		wm831x->charger_irq_wake = 1;
 		if (rev > 0) {
 			wm831x->has_gpio_ena = 1;
 			wm831x->has_cs_sts = 1;
@@ -1505,6 +1506,7 @@ static int wm831x_device_init(struct wm831x *wm831x, unsigned long id, int irq)
 	case WM8311:
 		parent = WM8311;
 		wm831x->num_gpio = 16;
+		wm831x->charger_irq_wake = 1;
 		if (rev > 0) {
 			wm831x->has_gpio_ena = 1;
 			wm831x->has_cs_sts = 1;
@@ -1516,6 +1518,7 @@ static int wm831x_device_init(struct wm831x *wm831x, unsigned long id, int irq)
 	case WM8312:
 		parent = WM8312;
 		wm831x->num_gpio = 16;
+		wm831x->charger_irq_wake = 1;
 		if (rev > 0) {
 			wm831x->has_gpio_ena = 1;
 			wm831x->has_cs_sts = 1;
@@ -1654,6 +1657,42 @@ static void wm831x_device_exit(struct wm831x *wm831x)
 	kfree(wm831x);
 }
 
+static int wm831x_device_suspend(struct wm831x *wm831x)
+{
+	int reg, mask;
+
+	/* If the charger IRQs are a wake source then make sure we ack
+	 * them even if they're not actively being used (eg, no power
+	 * driver or no IRQ line wired up) then acknowledge the
+	 * interrupts otherwise suspend won't last very long.
+	 */
+	if (wm831x->charger_irq_wake) {
+		reg = wm831x_reg_read(wm831x, WM831X_INTERRUPT_STATUS_2_MASK);
+
+		mask = WM831X_CHG_BATT_HOT_EINT |
+			WM831X_CHG_BATT_COLD_EINT |
+			WM831X_CHG_BATT_FAIL_EINT |
+			WM831X_CHG_OV_EINT | WM831X_CHG_END_EINT |
+			WM831X_CHG_TO_EINT | WM831X_CHG_MODE_EINT |
+			WM831X_CHG_START_EINT;
+
+		/* If any of the interrupts are masked read the statuses */
+		if (reg & mask)
+			reg = wm831x_reg_read(wm831x,
+					      WM831X_INTERRUPT_STATUS_2);
+
+		if (reg & mask) {
+			dev_info(wm831x->dev,
+				 "Acknowledging masked charger IRQs: %x\n",
+				 reg & mask);
+			wm831x_reg_write(wm831x, WM831X_INTERRUPT_STATUS_2,
+					 reg & mask);
+		}
+	}
+
+	return 0;
+}
+
 static int wm831x_i2c_read_device(struct wm831x *wm831x, unsigned short reg,
 				  int bytes, void *dest)
 {
@@ -1728,6 +1767,13 @@ static int wm831x_i2c_remove(struct i2c_client *i2c)
 	return 0;
 }
 
+static int wm831x_i2c_suspend(struct i2c_client *i2c, pm_message_t mesg)
+{
+	struct wm831x *wm831x = i2c_get_clientdata(i2c);
+
+	return wm831x_device_suspend(wm831x);
+}
+
 static const struct i2c_device_id wm831x_i2c_id[] = {
 	{ "wm8310", WM8310 },
 	{ "wm8311", WM8311 },
@@ -1745,6 +1791,7 @@ static struct i2c_driver wm831x_i2c_driver = {
 	},
 	.probe = wm831x_i2c_probe,
 	.remove = wm831x_i2c_remove,
+	.suspend = wm831x_i2c_suspend,
 	.id_table = wm831x_i2c_id,
 };