aboutsummaryrefslogtreecommitdiffstats
path: root/drivers/net/3c503.h
diff options
context:
space:
mode:
authorLinus Torvalds <torvalds@ppc970.osdl.org>2005-04-16 15:20:36 -0700
committerLinus Torvalds <torvalds@ppc970.osdl.org>2005-04-16 15:20:36 -0700
commit1da177e4c3f41524e886b7f1b8a0c1fc7321cac2 (patch)
tree0bba044c4ce775e45a88a51686b5d9f90697ea9d /drivers/net/3c503.h
downloadkernel_samsung_smdk4412-1da177e4c3f41524e886b7f1b8a0c1fc7321cac2.zip
kernel_samsung_smdk4412-1da177e4c3f41524e886b7f1b8a0c1fc7321cac2.tar.gz
kernel_samsung_smdk4412-1da177e4c3f41524e886b7f1b8a0c1fc7321cac2.tar.bz2
Linux-2.6.12-rc2
Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!
Diffstat (limited to 'drivers/net/3c503.h')
-rw-r--r--drivers/net/3c503.h91
1 files changed, 91 insertions, 0 deletions
diff --git a/drivers/net/3c503.h b/drivers/net/3c503.h
new file mode 100644
index 0000000..b9f8a46
--- /dev/null
+++ b/drivers/net/3c503.h
@@ -0,0 +1,91 @@
+/* Definitions for the 3Com 3c503 Etherlink 2. */
+/* This file is distributed under the GPL.
+ Many of these names and comments are directly from the Crynwr packet
+ drivers, which are released under the GPL. */
+
+#define EL2H (dev->base_addr + 0x400)
+#define EL2L (dev->base_addr)
+
+/* Vendor unique hardware addr. prefix. 3Com has 2 because they ran
+ out of available addresses on the first one... */
+
+#define OLD_3COM_ID 0x02608c
+#define NEW_3COM_ID 0x0020af
+
+/* Shared memory management parameters. NB: The 8 bit cards have only
+ one bank (MB1) which serves both Tx and Rx packet space. The 16bit
+ cards have 2 banks, MB0 for Tx packets, and MB1 for Rx packets.
+ You choose which bank appears in the sh. mem window with EGACFR_MBSn */
+
+#define EL2_MB0_START_PG (0x00) /* EL2/16 Tx packets go in bank 0 */
+#define EL2_MB1_START_PG (0x20) /* First page of bank 1 */
+#define EL2_MB1_STOP_PG (0x40) /* Last page +1 of bank 1 */
+
+/* 3Com 3c503 ASIC registers */
+#define E33G_STARTPG (EL2H+0) /* Start page, matching EN0_STARTPG */
+#define E33G_STOPPG (EL2H+1) /* Stop page, must match EN0_STOPPG */
+#define E33G_DRQCNT (EL2H+2) /* DMA burst count */
+#define E33G_IOBASE (EL2H+3) /* Read of I/O base jumpers. */
+ /* (non-useful, but it also appears at the end of EPROM space) */
+#define E33G_ROMBASE (EL2H+4) /* Read of memory base jumpers. */
+#define E33G_GACFR (EL2H+5) /* Config/setup bits for the ASIC GA */
+#define E33G_CNTRL (EL2H+6) /* Board's main control register */
+#define E33G_STATUS (EL2H+7) /* Status on completions. */
+#define E33G_IDCFR (EL2H+8) /* Interrupt/DMA config register */
+ /* (Which IRQ to assert, DMA chan to use) */
+#define E33G_DMAAH (EL2H+9) /* High byte of DMA address reg */
+#define E33G_DMAAL (EL2H+10) /* Low byte of DMA address reg */
+/* "Vector pointer" - if this address matches a read, the EPROM (rather than
+ shared RAM) is mapped into memory space. */
+#define E33G_VP2 (EL2H+11)
+#define E33G_VP1 (EL2H+12)
+#define E33G_VP0 (EL2H+13)
+#define E33G_FIFOH (EL2H+14) /* FIFO for programmed I/O moves */
+#define E33G_FIFOL (EL2H+15) /* ... low byte of above. */
+
+/* Bits in E33G_CNTRL register: */
+
+#define ECNTRL_RESET (0x01) /* Software reset of the ASIC and 8390 */
+#define ECNTRL_THIN (0x02) /* Onboard xcvr enable, AUI disable */
+#define ECNTRL_AUI (0x00) /* Onboard xcvr disable, AUI enable */
+#define ECNTRL_SAPROM (0x04) /* Map the station address prom */
+#define ECNTRL_DBLBFR (0x20) /* FIFO configuration bit */
+#define ECNTRL_OUTPUT (0x40) /* PC-to-3C503 direction if 1 */
+#define ECNTRL_INPUT (0x00) /* 3C503-to-PC direction if 0 */
+#define ECNTRL_START (0x80) /* Start the DMA logic */
+
+/* Bits in E33G_STATUS register: */
+
+#define ESTAT_DPRDY (0x80) /* Data port (of FIFO) ready */
+#define ESTAT_UFLW (0x40) /* Tried to read FIFO when it was empty */
+#define ESTAT_OFLW (0x20) /* Tried to write FIFO when it was full */
+#define ESTAT_DTC (0x10) /* Terminal Count from PC bus DMA logic */
+#define ESTAT_DIP (0x08) /* DMA In Progress */
+
+/* Bits in E33G_GACFR register: */
+
+#define EGACFR_NIM (0x80) /* NIC interrupt mask */
+#define EGACFR_TCM (0x40) /* DMA term. count interrupt mask */
+#define EGACFR_RSEL (0x08) /* Map a bank of card mem into system mem */
+#define EGACFR_MBS2 (0x04) /* Memory bank select, bit 2. */
+#define EGACFR_MBS1 (0x02) /* Memory bank select, bit 1. */
+#define EGACFR_MBS0 (0x01) /* Memory bank select, bit 0. */
+
+#define EGACFR_NORM (0x49) /* TCM | RSEL | MBS0 */
+#define EGACFR_IRQOFF (0xc9) /* TCM | RSEL | MBS0 | NIM */
+
+/*
+ MBS2 MBS1 MBS0 Sh. mem windows card mem at:
+ ---- ---- ---- -----------------------------
+ 0 0 0 0x0000 -- bank 0
+ 0 0 1 0x2000 -- bank 1 (only choice for 8bit card)
+ 0 1 0 0x4000 -- bank 2, not used
+ 0 1 1 0x6000 -- bank 3, not used
+
+There was going to be a 32k card that used bank 2 and 3, but it
+never got produced.
+
+*/
+
+
+/* End of 3C503 parameter definitions */