Linux-2.6.12-rc2

Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!

1 files changed, 3415 insertions, 0 deletions

diff --git a/drivers/parport/parport_pc.c b/drivers/parport/parport_pc.c
new file mode 100644
index 0000000..c5774e7
--- /dev/null
+++ b/drivers/parport/parport_pc.c
@@ -0,0 +1,3415 @@
+/* Low-level parallel-port routines for 8255-based PC-style hardware.
+ * 
+ * Authors: Phil Blundell <philb@gnu.org>
+ *          Tim Waugh <tim@cyberelk.demon.co.uk>
+ *	    Jose Renau <renau@acm.org>
+ *          David Campbell <campbell@torque.net>
+ *          Andrea Arcangeli
+ *
+ * based on work by Grant Guenther <grant@torque.net> and Phil Blundell.
+ *
+ * Cleaned up include files - Russell King <linux@arm.uk.linux.org>
+ * DMA support - Bert De Jonghe <bert@sophis.be>
+ * Many ECP bugs fixed.  Fred Barnes & Jamie Lokier, 1999
+ * More PCI support now conditional on CONFIG_PCI, 03/2001, Paul G. 
+ * Various hacks, Fred Barnes, 04/2001
+ * Updated probing logic - Adam Belay <ambx1@neo.rr.com>
+ */
+
+/* This driver should work with any hardware that is broadly compatible
+ * with that in the IBM PC.  This applies to the majority of integrated
+ * I/O chipsets that are commonly available.  The expected register
+ * layout is:
+ *
+ *	base+0		data
+ *	base+1		status
+ *	base+2		control
+ *
+ * In addition, there are some optional registers:
+ *
+ *	base+3		EPP address
+ *	base+4		EPP data
+ *	base+0x400	ECP config A
+ *	base+0x401	ECP config B
+ *	base+0x402	ECP control
+ *
+ * All registers are 8 bits wide and read/write.  If your hardware differs
+ * only in register addresses (eg because your registers are on 32-bit
+ * word boundaries) then you can alter the constants in parport_pc.h to
+ * accommodate this.
+ *
+ * Note that the ECP registers may not start at offset 0x400 for PCI cards,
+ * but rather will start at port->base_hi.
+ */
+
+#include <linux/config.h>
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/sched.h>
+#include <linux/delay.h>
+#include <linux/errno.h>
+#include <linux/interrupt.h>
+#include <linux/ioport.h>
+#include <linux/kernel.h>
+#include <linux/slab.h>
+#include <linux/pci.h>
+#include <linux/pnp.h>
+#include <linux/sysctl.h>
+
+#include <asm/io.h>
+#include <asm/dma.h>
+#include <asm/uaccess.h>
+
+#include <linux/parport.h>
+#include <linux/parport_pc.h>
+#include <linux/via.h>
+#include <asm/parport.h>
+
+#define PARPORT_PC_MAX_PORTS PARPORT_MAX
+
+/* ECR modes */
+#define ECR_SPP 00
+#define ECR_PS2 01
+#define ECR_PPF 02
+#define ECR_ECP 03
+#define ECR_EPP 04
+#define ECR_VND 05
+#define ECR_TST 06
+#define ECR_CNF 07
+#define ECR_MODE_MASK 0xe0
+#define ECR_WRITE(p,v) frob_econtrol((p),0xff,(v))
+
+#undef DEBUG
+
+#ifdef DEBUG
+#define DPRINTK  printk
+#else
+#define DPRINTK(stuff...)
+#endif
+
+
+#define NR_SUPERIOS 3
+static struct superio_struct {	/* For Super-IO chips autodetection */
+	int io;
+	int irq;
+	int dma;
+} superios[NR_SUPERIOS] __devinitdata = { {0,},};
+
+static int user_specified;
+#if defined(CONFIG_PARPORT_PC_SUPERIO) || \
+       (defined(CONFIG_PARPORT_1284) && defined(CONFIG_PARPORT_PC_FIFO))
+static int verbose_probing;
+#endif
+static int pci_registered_parport;
+static int pnp_registered_parport;
+
+/* frob_control, but for ECR */
+static void frob_econtrol (struct parport *pb, unsigned char m,
+			   unsigned char v)
+{
+	unsigned char ectr = 0;
+
+	if (m != 0xff)
+		ectr = inb (ECONTROL (pb));
+
+	DPRINTK (KERN_DEBUG "frob_econtrol(%02x,%02x): %02x -> %02x\n",
+		m, v, ectr, (ectr & ~m) ^ v);
+
+	outb ((ectr & ~m) ^ v, ECONTROL (pb));
+}
+
+static __inline__ void frob_set_mode (struct parport *p, int mode)
+{
+	frob_econtrol (p, ECR_MODE_MASK, mode << 5);
+}
+
+#ifdef CONFIG_PARPORT_PC_FIFO
+/* Safely change the mode bits in the ECR 
+   Returns:
+	    0    : Success
+	   -EBUSY: Could not drain FIFO in some finite amount of time,
+		   mode not changed!
+ */
+static int change_mode(struct parport *p, int m)
+{
+	const struct parport_pc_private *priv = p->physport->private_data;
+	unsigned char oecr;
+	int mode;
+
+	DPRINTK(KERN_INFO "parport change_mode ECP-ISA to mode 0x%02x\n",m);
+
+	if (!priv->ecr) {
+		printk (KERN_DEBUG "change_mode: but there's no ECR!\n");
+		return 0;
+	}
+
+	/* Bits <7:5> contain the mode. */
+	oecr = inb (ECONTROL (p));
+	mode = (oecr >> 5) & 0x7;
+	if (mode == m) return 0;
+
+	if (mode >= 2 && !(priv->ctr & 0x20)) {
+		/* This mode resets the FIFO, so we may
+		 * have to wait for it to drain first. */
+		unsigned long expire = jiffies + p->physport->cad->timeout;
+		int counter;
+		switch (mode) {
+		case ECR_PPF: /* Parallel Port FIFO mode */
+		case ECR_ECP: /* ECP Parallel Port mode */
+			/* Busy wait for 200us */
+			for (counter = 0; counter < 40; counter++) {
+				if (inb (ECONTROL (p)) & 0x01)
+					break;
+				if (signal_pending (current)) break;
+				udelay (5);
+			}
+
+			/* Poll slowly. */
+			while (!(inb (ECONTROL (p)) & 0x01)) {
+				if (time_after_eq (jiffies, expire))
+					/* The FIFO is stuck. */
+					return -EBUSY;
+				__set_current_state (TASK_INTERRUPTIBLE);
+				schedule_timeout ((HZ + 99) / 100);
+				if (signal_pending (current))
+					break;
+			}
+		}
+	}
+
+	if (mode >= 2 && m >= 2) {
+		/* We have to go through mode 001 */
+		oecr &= ~(7 << 5);
+		oecr |= ECR_PS2 << 5;
+		ECR_WRITE (p, oecr);
+	}
+
+	/* Set the mode. */
+	oecr &= ~(7 << 5);
+	oecr |= m << 5;
+	ECR_WRITE (p, oecr);
+	return 0;
+}
+
+#ifdef CONFIG_PARPORT_1284
+/* Find FIFO lossage; FIFO is reset */
+#if 0
+static int get_fifo_residue (struct parport *p)
+{
+	int residue;
+	int cnfga;
+	const struct parport_pc_private *priv = p->physport->private_data;
+
+	/* Adjust for the contents of the FIFO. */
+	for (residue = priv->fifo_depth; ; residue--) {
+		if (inb (ECONTROL (p)) & 0x2)
+				/* Full up. */
+			break;
+
+		outb (0, FIFO (p));
+	}
+
+	printk (KERN_DEBUG "%s: %d PWords were left in FIFO\n", p->name,
+		residue);
+
+	/* Reset the FIFO. */
+	frob_set_mode (p, ECR_PS2);
+
+	/* Now change to config mode and clean up. FIXME */
+	frob_set_mode (p, ECR_CNF);
+	cnfga = inb (CONFIGA (p));
+	printk (KERN_DEBUG "%s: cnfgA contains 0x%02x\n", p->name, cnfga);
+
+	if (!(cnfga & (1<<2))) {
+		printk (KERN_DEBUG "%s: Accounting for extra byte\n", p->name);
+		residue++;
+	}
+
+	/* Don't care about partial PWords until support is added for
+	 * PWord != 1 byte. */
+
+	/* Back to PS2 mode. */
+	frob_set_mode (p, ECR_PS2);
+
+	DPRINTK (KERN_DEBUG "*** get_fifo_residue: done residue collecting (ecr = 0x%2.2x)\n", inb (ECONTROL (p)));
+	return residue;
+}
+#endif  /*  0 */
+#endif /* IEEE 1284 support */
+#endif /* FIFO support */
+
+/*
+ * Clear TIMEOUT BIT in EPP MODE
+ *
+ * This is also used in SPP detection.
+ */
+static int clear_epp_timeout(struct parport *pb)
+{
+	unsigned char r;
+
+	if (!(parport_pc_read_status(pb) & 0x01))
+		return 1;
+
+	/* To clear timeout some chips require double read */
+	parport_pc_read_status(pb);
+	r = parport_pc_read_status(pb);
+	outb (r | 0x01, STATUS (pb)); /* Some reset by writing 1 */
+	outb (r & 0xfe, STATUS (pb)); /* Others by writing 0 */
+	r = parport_pc_read_status(pb);
+
+	return !(r & 0x01);
+}
+
+/*
+ * Access functions.
+ *
+ * Most of these aren't static because they may be used by the
+ * parport_xxx_yyy macros.  extern __inline__ versions of several
+ * of these are in parport_pc.h.
+ */
+
+static irqreturn_t parport_pc_interrupt(int irq, void *dev_id, struct pt_regs *regs)
+{
+	parport_generic_irq(irq, (struct parport *) dev_id, regs);
+	/* FIXME! Was it really ours? */
+	return IRQ_HANDLED;
+}
+
+static void parport_pc_init_state(struct pardevice *dev, struct parport_state *s)
+{
+	s->u.pc.ctr = 0xc;
+	if (dev->irq_func &&
+	    dev->port->irq != PARPORT_IRQ_NONE)
+		/* Set ackIntEn */
+		s->u.pc.ctr |= 0x10;
+
+	s->u.pc.ecr = 0x34; /* NetMos chip can cause problems 0x24;
+			     * D.Gruszka VScom */
+}
+
+static void parport_pc_save_state(struct parport *p, struct parport_state *s)
+{
+	const struct parport_pc_private *priv = p->physport->private_data;
+	s->u.pc.ctr = priv->ctr;
+	if (priv->ecr)
+		s->u.pc.ecr = inb (ECONTROL (p));
+}
+
+static void parport_pc_restore_state(struct parport *p, struct parport_state *s)
+{
+	struct parport_pc_private *priv = p->physport->private_data;
+	register unsigned char c = s->u.pc.ctr & priv->ctr_writable;
+	outb (c, CONTROL (p));
+	priv->ctr = c;
+	if (priv->ecr)
+		ECR_WRITE (p, s->u.pc.ecr);
+}
+
+#ifdef CONFIG_PARPORT_1284
+static size_t parport_pc_epp_read_data (struct parport *port, void *buf,
+					size_t length, int flags)
+{
+	size_t got = 0;
+
+	if (flags & PARPORT_W91284PIC) {
+		unsigned char status;
+		size_t left = length;
+
+		/* use knowledge about data lines..:
+		 *  nFault is 0 if there is at least 1 byte in the Warp's FIFO
+		 *  pError is 1 if there are 16 bytes in the Warp's FIFO
+		 */
+		status = inb (STATUS (port));
+
+		while (!(status & 0x08) && (got < length)) {
+			if ((left >= 16) && (status & 0x20) && !(status & 0x08)) {
+				/* can grab 16 bytes from warp fifo */
+				if (!((long)buf & 0x03)) {
+					insl (EPPDATA (port), buf, 4);
+				} else {
+					insb (EPPDATA (port), buf, 16);
+				}
+				buf += 16;
+				got += 16;
+				left -= 16;
+			} else {
+				/* grab single byte from the warp fifo */
+				*((char *)buf) = inb (EPPDATA (port));
+				buf++;
+				got++;
+				left--;
+			}
+			status = inb (STATUS (port));
+			if (status & 0x01) {
+				/* EPP timeout should never occur... */
+				printk (KERN_DEBUG "%s: EPP timeout occurred while talking to "
+					"w91284pic (should not have done)\n", port->name);
+				clear_epp_timeout (port);
+			}
+		}
+		return got;
+	}
+	if ((flags & PARPORT_EPP_FAST) && (length > 1)) {
+		if (!(((long)buf | length) & 0x03)) {
+			insl (EPPDATA (port), buf, (length >> 2));
+		} else {
+			insb (EPPDATA (port), buf, length);
+		}
+		if (inb (STATUS (port)) & 0x01) {
+			clear_epp_timeout (port);
+			return -EIO;
+		}
+		return length;
+	}
+	for (; got < length; got++) {
+		*((char*)buf) = inb (EPPDATA(port));
+		buf++;
+		if (inb (STATUS (port)) & 0x01) {
+			/* EPP timeout */
+			clear_epp_timeout (port);
+			break;
+		}
+	}
+
+	return got;
+}
+
+static size_t parport_pc_epp_write_data (struct parport *port, const void *buf,
+					 size_t length, int flags)
+{
+	size_t written = 0;
+
+	if ((flags & PARPORT_EPP_FAST) && (length > 1)) {
+		if (!(((long)buf | length) & 0x03)) {
+			outsl (EPPDATA (port), buf, (length >> 2));
+		} else {
+			outsb (EPPDATA (port), buf, length);
+		}
+		if (inb (STATUS (port)) & 0x01) {
+			clear_epp_timeout (port);
+			return -EIO;
+		}
+		return length;
+	}
+	for (; written < length; written++) {
+		outb (*((char*)buf), EPPDATA(port));
+		buf++;
+		if (inb (STATUS(port)) & 0x01) {
+			clear_epp_timeout (port);
+			break;
+		}
+	}
+
+	return written;
+}
+
+static size_t parport_pc_epp_read_addr (struct parport *port, void *buf,
+					size_t length, int flags)
+{
+	size_t got = 0;
+
+	if ((flags & PARPORT_EPP_FAST) && (length > 1)) {
+		insb (EPPADDR (port), buf, length);
+		if (inb (STATUS (port)) & 0x01) {
+			clear_epp_timeout (port);
+			return -EIO;
+		}
+		return length;
+	}
+	for (; got < length; got++) {
+		*((char*)buf) = inb (EPPADDR (port));
+		buf++;
+		if (inb (STATUS (port)) & 0x01) {
+			clear_epp_timeout (port);
+			break;
+		}
+	}
+
+	return got;
+}
+
+static size_t parport_pc_epp_write_addr (struct parport *port,
+					 const void *buf, size_t length,
+					 int flags)
+{
+	size_t written = 0;
+
+	if ((flags & PARPORT_EPP_FAST) && (length > 1)) {
+		outsb (EPPADDR (port), buf, length);
+		if (inb (STATUS (port)) & 0x01) {
+			clear_epp_timeout (port);
+			return -EIO;
+		}
+		return length;
+	}
+	for (; written < length; written++) {
+		outb (*((char*)buf), EPPADDR (port));
+		buf++;
+		if (inb (STATUS (port)) & 0x01) {
+			clear_epp_timeout (port);
+			break;
+		}
+	}
+
+	return written;
+}
+
+static size_t parport_pc_ecpepp_read_data (struct parport *port, void *buf,
+					   size_t length, int flags)
+{
+	size_t got;
+
+	frob_set_mode (port, ECR_EPP);
+	parport_pc_data_reverse (port);
+	parport_pc_write_control (port, 0x4);
+	got = parport_pc_epp_read_data (port, buf, length, flags);
+	frob_set_mode (port, ECR_PS2);
+
+	return got;
+}
+
+static size_t parport_pc_ecpepp_write_data (struct parport *port,
+					    const void *buf, size_t length,
+					    int flags)
+{
+	size_t written;
+
+	frob_set_mode (port, ECR_EPP);
+	parport_pc_write_control (port, 0x4);
+	parport_pc_data_forward (port);
+	written = parport_pc_epp_write_data (port, buf, length, flags);
+	frob_set_mode (port, ECR_PS2);
+
+	return written;
+}
+
+static size_t parport_pc_ecpepp_read_addr (struct parport *port, void *buf,
+					   size_t length, int flags)
+{
+	size_t got;
+
+	frob_set_mode (port, ECR_EPP);
+	parport_pc_data_reverse (port);
+	parport_pc_write_control (port, 0x4);
+	got = parport_pc_epp_read_addr (port, buf, length, flags);
+	frob_set_mode (port, ECR_PS2);
+
+	return got;
+}
+
+static size_t parport_pc_ecpepp_write_addr (struct parport *port,
+					    const void *buf, size_t length,
+					    int flags)
+{
+	size_t written;
+
+	frob_set_mode (port, ECR_EPP);
+	parport_pc_write_control (port, 0x4);
+	parport_pc_data_forward (port);
+	written = parport_pc_epp_write_addr (port, buf, length, flags);
+	frob_set_mode (port, ECR_PS2);
+
+	return written;
+}
+#endif /* IEEE 1284 support */
+
+#ifdef CONFIG_PARPORT_PC_FIFO
+static size_t parport_pc_fifo_write_block_pio (struct parport *port,
+					       const void *buf, size_t length)
+{
+	int ret = 0;
+	const unsigned char *bufp = buf;
+	size_t left = length;
+	unsigned long expire = jiffies + port->physport->cad->timeout;
+	const int fifo = FIFO (port);
+	int poll_for = 8; /* 80 usecs */
+	const struct parport_pc_private *priv = port->physport->private_data;
+	const int fifo_depth = priv->fifo_depth;
+
+	port = port->physport;
+
+	/* We don't want to be interrupted every character. */
+	parport_pc_disable_irq (port);
+	/* set nErrIntrEn and serviceIntr */
+	frob_econtrol (port, (1<<4) | (1<<2), (1<<4) | (1<<2));
+
+	/* Forward mode. */
+	parport_pc_data_forward (port); /* Must be in PS2 mode */
+
+	while (left) {
+		unsigned char byte;
+		unsigned char ecrval = inb (ECONTROL (port));
+		int i = 0;
+
+		if (need_resched() && time_before (jiffies, expire))
+			/* Can't yield the port. */
+			schedule ();
+
+		/* Anyone else waiting for the port? */
+		if (port->waithead) {
+			printk (KERN_DEBUG "Somebody wants the port\n");
+			break;
+		}
+
+		if (ecrval & 0x02) {
+			/* FIFO is full. Wait for interrupt. */
+
+			/* Clear serviceIntr */
+			ECR_WRITE (port, ecrval & ~(1<<2));
+		false_alarm:
+			ret = parport_wait_event (port, HZ);
+			if (ret < 0) break;
+			ret = 0;
+			if (!time_before (jiffies, expire)) {
+				/* Timed out. */
+				printk (KERN_DEBUG "FIFO write timed out\n");
+				break;
+			}
+			ecrval = inb (ECONTROL (port));
+			if (!(ecrval & (1<<2))) {
+				if (need_resched() &&
+				    time_before (jiffies, expire))
+					schedule ();
+
+				goto false_alarm;
+			}
+
+			continue;
+		}
+
+		/* Can't fail now. */
+		expire = jiffies + port->cad->timeout;
+
+	poll:
+		if (signal_pending (current))
+			break;
+
+		if (ecrval & 0x01) {
+			/* FIFO is empty. Blast it full. */
+			const int n = left < fifo_depth ? left : fifo_depth;
+			outsb (fifo, bufp, n);
+			bufp += n;
+			left -= n;
+
+			/* Adjust the poll time. */
+			if (i < (poll_for - 2)) poll_for--;
+			continue;
+		} else if (i++ < poll_for) {
+			udelay (10);
+			ecrval = inb (ECONTROL (port));
+			goto poll;
+		}
+
+		/* Half-full (call me an optimist) */
+		byte = *bufp++;
+		outb (byte, fifo);
+		left--;
+        }
+
+dump_parport_state ("leave fifo_write_block_pio", port);
+	return length - left;
+}
+
+static size_t parport_pc_fifo_write_block_dma (struct parport *port,
+					       const void *buf, size_t length)
+{
+	int ret = 0;
+	unsigned long dmaflag;
+	size_t left = length;
+	const struct parport_pc_private *priv = port->physport->private_data;
+	dma_addr_t dma_addr, dma_handle;
+	size_t maxlen = 0x10000; /* max 64k per DMA transfer */
+	unsigned long start = (unsigned long) buf;
+	unsigned long end = (unsigned long) buf + length - 1;
+
+dump_parport_state ("enter fifo_write_block_dma", port);
+	if (end < MAX_DMA_ADDRESS) {
+		/* If it would cross a 64k boundary, cap it at the end. */
+		if ((start ^ end) & ~0xffffUL)
+			maxlen = 0x10000 - (start & 0xffff);
+
+		dma_addr = dma_handle = pci_map_single(priv->dev, (void *)buf, length,
+						       PCI_DMA_TODEVICE);
+        } else {
+		/* above 16 MB we use a bounce buffer as ISA-DMA is not possible */
+		maxlen   = PAGE_SIZE;          /* sizeof(priv->dma_buf) */
+		dma_addr = priv->dma_handle;
+		dma_handle = 0;
+	}
+
+	port = port->physport;
+
+	/* We don't want to be interrupted every character. */
+	parport_pc_disable_irq (port);
+	/* set nErrIntrEn and serviceIntr */
+	frob_econtrol (port, (1<<4) | (1<<2), (1<<4) | (1<<2));
+
+	/* Forward mode. */
+	parport_pc_data_forward (port); /* Must be in PS2 mode */
+
+	while (left) {
+		unsigned long expire = jiffies + port->physport->cad->timeout;
+
+		size_t count = left;
+
+		if (count > maxlen)
+			count = maxlen;
+
+		if (!dma_handle)   /* bounce buffer ! */
+			memcpy(priv->dma_buf, buf, count);
+
+		dmaflag = claim_dma_lock();
+		disable_dma(port->dma);
+		clear_dma_ff(port->dma);
+		set_dma_mode(port->dma, DMA_MODE_WRITE);
+		set_dma_addr(port->dma, dma_addr);
+		set_dma_count(port->dma, count);
+
+		/* Set DMA mode */
+		frob_econtrol (port, 1<<3, 1<<3);
+
+		/* Clear serviceIntr */
+		frob_econtrol (port, 1<<2, 0);
+
+		enable_dma(port->dma);
+		release_dma_lock(dmaflag);
+
+		/* assume DMA will be successful */
+		left -= count;
+		buf  += count;
+		if (dma_handle) dma_addr += count;
+
+		/* Wait for interrupt. */
+	false_alarm:
+		ret = parport_wait_event (port, HZ);
+		if (ret < 0) break;
+		ret = 0;
+		if (!time_before (jiffies, expire)) {
+			/* Timed out. */
+			printk (KERN_DEBUG "DMA write timed out\n");
+			break;
+		}
+		/* Is serviceIntr set? */
+		if (!(inb (ECONTROL (port)) & (1<<2))) {
+			cond_resched();
+
+			goto false_alarm;
+		}
+
+		dmaflag = claim_dma_lock();
+		disable_dma(port->dma);
+		clear_dma_ff(port->dma);
+		count = get_dma_residue(port->dma);
+		release_dma_lock(dmaflag);
+
+		cond_resched(); /* Can't yield the port. */
+
+		/* Anyone else waiting for the port? */
+		if (port->waithead) {
+			printk (KERN_DEBUG "Somebody wants the port\n");
+			break;
+		}
+
+		/* update for possible DMA residue ! */
+		buf  -= count;
+		left += count;
+		if (dma_handle) dma_addr -= count;
+	}
+
+	/* Maybe got here through break, so adjust for DMA residue! */
+	dmaflag = claim_dma_lock();
+	disable_dma(port->dma);
+	clear_dma_ff(port->dma);
+	left += get_dma_residue(port->dma);
+	release_dma_lock(dmaflag);
+
+	/* Turn off DMA mode */
+	frob_econtrol (port, 1<<3, 0);
+	
+	if (dma_handle)
+		pci_unmap_single(priv->dev, dma_handle, length, PCI_DMA_TODEVICE);
+
+dump_parport_state ("leave fifo_write_block_dma", port);
+	return length - left;
+}
+
+/* Parallel Port FIFO mode (ECP chipsets) */
+static size_t parport_pc_compat_write_block_pio (struct parport *port,
+						 const void *buf, size_t length,
+						 int flags)
+{
+	size_t written;
+	int r;
+	unsigned long expire;
+	const struct parport_pc_private *priv = port->physport->private_data;
+
+	/* Special case: a timeout of zero means we cannot call schedule().
+	 * Also if O_NONBLOCK is set then use the default implementation. */
+	if (port->physport->cad->timeout <= PARPORT_INACTIVITY_O_NONBLOCK)
+		return parport_ieee1284_write_compat (port, buf,
+						      length, flags);
+
+	/* Set up parallel port FIFO mode.*/
+	parport_pc_data_forward (port); /* Must be in PS2 mode */
+	parport_pc_frob_control (port, PARPORT_CONTROL_STROBE, 0);
+	r = change_mode (port, ECR_PPF); /* Parallel port FIFO */
+	if (r)  printk (KERN_DEBUG "%s: Warning change_mode ECR_PPF failed\n", port->name);
+
+	port->physport->ieee1284.phase = IEEE1284_PH_FWD_DATA;
+
+	/* Write the data to the FIFO. */
+	if (port->dma != PARPORT_DMA_NONE)
+		written = parport_pc_fifo_write_block_dma (port, buf, length);
+	else
+		written = parport_pc_fifo_write_block_pio (port, buf, length);
+
+	/* Finish up. */
+	/* For some hardware we don't want to touch the mode until
+	 * the FIFO is empty, so allow 4 seconds for each position
+	 * in the fifo.
+	 */
+        expire = jiffies + (priv->fifo_depth * HZ * 4);
+	do {
+		/* Wait for the FIFO to empty */
+		r = change_mode (port, ECR_PS2);
+		if (r != -EBUSY) {
+			break;
+		}
+	} while (time_before (jiffies, expire));
+	if (r == -EBUSY) {
+
+		printk (KERN_DEBUG "%s: FIFO is stuck\n", port->name);
+
+		/* Prevent further data transfer. */
+		frob_set_mode (port, ECR_TST);
+
+		/* Adjust for the contents of the FIFO. */
+		for (written -= priv->fifo_depth; ; written++) {
+			if (inb (ECONTROL (port)) & 0x2) {
+				/* Full up. */
+				break;
+			}
+			outb (0, FIFO (port));
+		}
+
+		/* Reset the FIFO and return to PS2 mode. */
+		frob_set_mode (port, ECR_PS2);
+	}
+
+	r = parport_wait_peripheral (port,
+				     PARPORT_STATUS_BUSY,
+				     PARPORT_STATUS_BUSY);
+	if (r)
+		printk (KERN_DEBUG
+			"%s: BUSY timeout (%d) in compat_write_block_pio\n", 
+			port->name, r);
+
+	port->physport->ieee1284.phase = IEEE1284_PH_FWD_IDLE;
+
+	return written;
+}
+
+/* ECP */
+#ifdef CONFIG_PARPORT_1284
+static size_t parport_pc_ecp_write_block_pio (struct parport *port,
+					      const void *buf, size_t length,
+					      int flags)
+{
+	size_t written;
+	int r;
+	unsigned long expire;
+	const struct parport_pc_private *priv = port->physport->private_data;
+
+	/* Special case: a timeout of zero means we cannot call schedule().
+	 * Also if O_NONBLOCK is set then use the default implementation. */
+	if (port->physport->cad->timeout <= PARPORT_INACTIVITY_O_NONBLOCK)
+		return parport_ieee1284_ecp_write_data (port, buf,
+							length, flags);
+
+	/* Switch to forward mode if necessary. */
+	if (port->physport->ieee1284.phase != IEEE1284_PH_FWD_IDLE) {
+		/* Event 47: Set nInit high. */
+		parport_frob_control (port,
+				      PARPORT_CONTROL_INIT
+				      | PARPORT_CONTROL_AUTOFD,
+				      PARPORT_CONTROL_INIT
+				      | PARPORT_CONTROL_AUTOFD);
+
+		/* Event 49: PError goes high. */
+		r = parport_wait_peripheral (port,
+					     PARPORT_STATUS_PAPEROUT,
+					     PARPORT_STATUS_PAPEROUT);
+		if (r) {
+			printk (KERN_DEBUG "%s: PError timeout (%d) "
+				"in ecp_write_block_pio\n", port->name, r);
+		}
+	}
+
+	/* Set up ECP parallel port mode.*/
+	parport_pc_data_forward (port); /* Must be in PS2 mode */
+	parport_pc_frob_control (port,
+				 PARPORT_CONTROL_STROBE |
+				 PARPORT_CONTROL_AUTOFD,
+				 0);
+	r = change_mode (port, ECR_ECP); /* ECP FIFO */
+	if (r) printk (KERN_DEBUG "%s: Warning change_mode ECR_ECP failed\n", port->name);
+	port->physport->ieee1284.phase = IEEE1284_PH_FWD_DATA;
+
+	/* Write the data to the FIFO. */
+	if (port->dma != PARPORT_DMA_NONE)
+		written = parport_pc_fifo_write_block_dma (port, buf, length);
+	else
+		written = parport_pc_fifo_write_block_pio (port, buf, length);
+
+	/* Finish up. */
+	/* For some hardware we don't want to touch the mode until
+	 * the FIFO is empty, so allow 4 seconds for each position
+	 * in the fifo.
+	 */
+	expire = jiffies + (priv->fifo_depth * (HZ * 4));
+	do {
+		/* Wait for the FIFO to empty */
+		r = change_mode (port, ECR_PS2);
+		if (r != -EBUSY) {
+			break;
+		}
+	} while (time_before (jiffies, expire));
+	if (r == -EBUSY) {
+
+		printk (KERN_DEBUG "%s: FIFO is stuck\n", port->name);
+
+		/* Prevent further data transfer. */
+		frob_set_mode (port, ECR_TST);
+
+		/* Adjust for the contents of the FIFO. */
+		for (written -= priv->fifo_depth; ; written++) {
+			if (inb (ECONTROL (port)) & 0x2) {
+				/* Full up. */
+				break;
+			}
+			outb (0, FIFO (port));
+		}
+
+		/* Reset the FIFO and return to PS2 mode. */
+		frob_set_mode (port, ECR_PS2);
+
+		/* Host transfer recovery. */
+		parport_pc_data_reverse (port); /* Must be in PS2 mode */
+		udelay (5);
+		parport_frob_control (port, PARPORT_CONTROL_INIT, 0);
+		r = parport_wait_peripheral (port, PARPORT_STATUS_PAPEROUT, 0);
+		if (r)
+			printk (KERN_DEBUG "%s: PE,1 timeout (%d) "
+				"in ecp_write_block_pio\n", port->name, r);
+
+		parport_frob_control (port,
+				      PARPORT_CONTROL_INIT,
+				      PARPORT_CONTROL_INIT);
+		r = parport_wait_peripheral (port,
+					     PARPORT_STATUS_PAPEROUT,
+					     PARPORT_STATUS_PAPEROUT);
+                if (r)
+                        printk (KERN_DEBUG "%s: PE,2 timeout (%d) "
+				"in ecp_write_block_pio\n", port->name, r);
+	}
+
+	r = parport_wait_peripheral (port,
+				     PARPORT_STATUS_BUSY, 
+				     PARPORT_STATUS_BUSY);
+	if(r)
+		printk (KERN_DEBUG
+			"%s: BUSY timeout (%d) in ecp_write_block_pio\n",
+			port->name, r);
+
+	port->physport->ieee1284.phase = IEEE1284_PH_FWD_IDLE;
+
+	return written;
+}
+
+#if 0
+static size_t parport_pc_ecp_read_block_pio (struct parport *port,
+					     void *buf, size_t length,
+					     int flags)
+{
+	size_t left = length;
+	size_t fifofull;
+	int r;
+	const int fifo = FIFO(port);
+	const struct parport_pc_private *priv = port->physport->private_data;
+	const int fifo_depth = priv->fifo_depth;
+	char *bufp = buf;
+
+	port = port->physport;
+DPRINTK (KERN_DEBUG "parport_pc: parport_pc_ecp_read_block_pio\n");
+dump_parport_state ("enter fcn", port);
+
+	/* Special case: a timeout of zero means we cannot call schedule().
+	 * Also if O_NONBLOCK is set then use the default implementation. */
+	if (port->cad->timeout <= PARPORT_INACTIVITY_O_NONBLOCK)
+		return parport_ieee1284_ecp_read_data (port, buf,
+						       length, flags);
+
+	if (port->ieee1284.mode == IEEE1284_MODE_ECPRLE) {
+		/* If the peripheral is allowed to send RLE compressed
+		 * data, it is possible for a byte to expand to 128
+		 * bytes in the FIFO. */
+		fifofull = 128;
+	} else {
+		fifofull = fifo_depth;
+	}
+
+	/* If the caller wants less than a full FIFO's worth of data,
+	 * go through software emulation.  Otherwise we may have to throw
+	 * away data. */
+	if (length < fifofull)
+		return parport_ieee1284_ecp_read_data (port, buf,
+						       length, flags);
+
+	if (port->ieee1284.phase != IEEE1284_PH_REV_IDLE) {
+		/* change to reverse-idle phase (must be in forward-idle) */
+
+		/* Event 38: Set nAutoFd low (also make sure nStrobe is high) */
+		parport_frob_control (port,
+				      PARPORT_CONTROL_AUTOFD
+				      | PARPORT_CONTROL_STROBE,
+				      PARPORT_CONTROL_AUTOFD);
+		parport_pc_data_reverse (port); /* Must be in PS2 mode */
+		udelay (5);
+		/* Event 39: Set nInit low to initiate bus reversal */
+		parport_frob_control (port,
+				      PARPORT_CONTROL_INIT,
+				      0);
+		/* Event 40: Wait for  nAckReverse (PError) to go low */
+		r = parport_wait_peripheral (port, PARPORT_STATUS_PAPEROUT, 0);
+                if (r) {
+                        printk (KERN_DEBUG "%s: PE timeout Event 40 (%d) "
+				"in ecp_read_block_pio\n", port->name, r);
+			return 0;
+		}
+	}
+
+	/* Set up ECP FIFO mode.*/
+/*	parport_pc_frob_control (port,
+				 PARPORT_CONTROL_STROBE |
+				 PARPORT_CONTROL_AUTOFD,
+				 PARPORT_CONTROL_AUTOFD); */
+	r = change_mode (port, ECR_ECP); /* ECP FIFO */
+	if (r) printk (KERN_DEBUG "%s: Warning change_mode ECR_ECP failed\n", port->name);
+
+	port->ieee1284.phase = IEEE1284_PH_REV_DATA;
+
+	/* the first byte must be collected manually */
+dump_parport_state ("pre 43", port);
+	/* Event 43: Wait for nAck to go low */
+	r = parport_wait_peripheral (port, PARPORT_STATUS_ACK, 0);
+	if (r) {
+		/* timed out while reading -- no data */
+		printk (KERN_DEBUG "PIO read timed out (initial byte)\n");
+		goto out_no_data;
+	}
+	/* read byte */
+	*bufp++ = inb (DATA (port));
+	left--;
+dump_parport_state ("43-44", port);
+	/* Event 44: nAutoFd (HostAck) goes high to acknowledge */
+	parport_pc_frob_control (port,
+				 PARPORT_CONTROL_AUTOFD,
+				 0);
+dump_parport_state ("pre 45", port);
+	/* Event 45: Wait for nAck to go high */
+/*	r = parport_wait_peripheral (port, PARPORT_STATUS_ACK, PARPORT_STATUS_ACK); */
+dump_parport_state ("post 45", port);
+r = 0;
+	if (r) {
+		/* timed out while waiting for peripheral to respond to ack */
+		printk (KERN_DEBUG "ECP PIO read timed out (waiting for nAck)\n");
+
+		/* keep hold of the byte we've got already */
+		goto out_no_data;
+	}
+	/* Event 46: nAutoFd (HostAck) goes low to accept more data */
+	parport_pc_frob_control (port,
+				 PARPORT_CONTROL_AUTOFD,
+				 PARPORT_CONTROL_AUTOFD);
+
+
+dump_parport_state ("rev idle", port);
+	/* Do the transfer. */
+	while (left > fifofull) {
+		int ret;
+		unsigned long expire = jiffies + port->cad->timeout;
+		unsigned char ecrval = inb (ECONTROL (port));
+
+		if (need_resched() && time_before (jiffies, expire))
+			/* Can't yield the port. */
+			schedule ();
+
+		/* At this point, the FIFO may already be full. In
+                 * that case ECP is already holding back the
+                 * peripheral (assuming proper design) with a delayed
+                 * handshake.  Work fast to avoid a peripheral
+                 * timeout.  */
+
+		if (ecrval & 0x01) {
+			/* FIFO is empty. Wait for interrupt. */
+dump_parport_state ("FIFO empty", port);
+
+			/* Anyone else waiting for the port? */
+			if (port->waithead) {
+				printk (KERN_DEBUG "Somebody wants the port\n");
+				break;
+			}
+
+			/* Clear serviceIntr */
+			ECR_WRITE (port, ecrval & ~(1<<2));
+		false_alarm:
+dump_parport_state ("waiting", port);
+			ret = parport_wait_event (port, HZ);
+DPRINTK (KERN_DEBUG "parport_wait_event returned %d\n", ret);
+			if (ret < 0)
+				break;
+			ret = 0;
+			if (!time_before (jiffies, expire)) {
+				/* Timed out. */
+dump_parport_state ("timeout", port);
+				printk (KERN_DEBUG "PIO read timed out\n");
+				break;
+			}
+			ecrval = inb (ECONTROL (port));
+			if (!(ecrval & (1<<2))) {
+				if (need_resched() &&
+				    time_before (jiffies, expire)) {
+					schedule ();
+				}
+				goto false_alarm;
+			}
+
+			/* Depending on how the FIFO threshold was
+                         * set, how long interrupt service took, and
+                         * how fast the peripheral is, we might be
+                         * lucky and have a just filled FIFO. */
+			continue;
+		}
+
+		if (ecrval & 0x02) {
+			/* FIFO is full. */
+dump_parport_state ("FIFO full", port);
+			insb (fifo, bufp, fifo_depth);
+			bufp += fifo_depth;
+			left -= fifo_depth;
+			continue;
+		}
+
+DPRINTK (KERN_DEBUG "*** ecp_read_block_pio: reading one byte from the FIFO\n");
+
+		/* FIFO not filled.  We will cycle this loop for a while
+                 * and either the peripheral will fill it faster,
+                 * tripping a fast empty with insb, or we empty it. */
+		*bufp++ = inb (fifo);
+		left--;
+	}
+
+	/* scoop up anything left in the FIFO */
+	while (left && !(inb (ECONTROL (port) & 0x01))) {
+		*bufp++ = inb (fifo);
+		left--;
+	}
+
+	port->ieee1284.phase = IEEE1284_PH_REV_IDLE;
+dump_parport_state ("rev idle2", port);
+
+out_no_data:
+
+	/* Go to forward idle mode to shut the peripheral up (event 47). */
+	parport_frob_control (port, PARPORT_CONTROL_INIT, PARPORT_CONTROL_INIT);
+
+	/* event 49: PError goes high */
+	r = parport_wait_peripheral (port,
+				     PARPORT_STATUS_PAPEROUT,
+				     PARPORT_STATUS_PAPEROUT);
+	if (r) {
+		printk (KERN_DEBUG
+			"%s: PE timeout FWDIDLE (%d) in ecp_read_block_pio\n",
+			port->name, r);
+	}
+
+	port->ieee1284.phase = IEEE1284_PH_FWD_IDLE;
+
+	/* Finish up. */
+	{
+		int lost = get_fifo_residue (port);
+		if (lost)
+			/* Shouldn't happen with compliant peripherals. */
+			printk (KERN_DEBUG "%s: DATA LOSS (%d bytes)!\n",
+				port->name, lost);
+	}
+
+dump_parport_state ("fwd idle", port);
+	return length - left;
+}
+#endif  /*  0  */
+#endif /* IEEE 1284 support */
+#endif /* Allowed to use FIFO/DMA */
+
+
+/*
+ *	******************************************
+ *	INITIALISATION AND MODULE STUFF BELOW HERE
+ *	******************************************
+ */
+
+/* GCC is not inlining extern inline function later overwriten to non-inline,
+   so we use outlined_ variants here.  */
+static struct parport_operations parport_pc_ops =
+{
+	.write_data	= parport_pc_write_data,
+	.read_data	= parport_pc_read_data,
+
+	.write_control	= parport_pc_write_control,
+	.read_control	= parport_pc_read_control,
+	.frob_control	= parport_pc_frob_control,
+
+	.read_status	= parport_pc_read_status,
+
+	.enable_irq	= parport_pc_enable_irq,
+	.disable_irq	= parport_pc_disable_irq,
+
+	.data_forward	= parport_pc_data_forward,
+	.data_reverse	= parport_pc_data_reverse,
+
+	.init_state	= parport_pc_init_state,
+	.save_state	= parport_pc_save_state,
+	.restore_state	= parport_pc_restore_state,
+
+	.epp_write_data	= parport_ieee1284_epp_write_data,
+	.epp_read_data	= parport_ieee1284_epp_read_data,
+	.epp_write_addr	= parport_ieee1284_epp_write_addr,
+	.epp_read_addr	= parport_ieee1284_epp_read_addr,
+
+	.ecp_write_data	= parport_ieee1284_ecp_write_data,
+	.ecp_read_data	= parport_ieee1284_ecp_read_data,
+	.ecp_write_addr	= parport_ieee1284_ecp_write_addr,
+
+	.compat_write_data	= parport_ieee1284_write_compat,
+	.nibble_read_data	= parport_ieee1284_read_nibble,
+	.byte_read_data		= parport_ieee1284_read_byte,
+
+	.owner		= THIS_MODULE,
+};
+
+#ifdef CONFIG_PARPORT_PC_SUPERIO
+/* Super-IO chipset detection, Winbond, SMSC */
+static void __devinit show_parconfig_smsc37c669(int io, int key)
+{
+	int cr1,cr4,cra,cr23,cr26,cr27,i=0;
+	static const char *modes[]={ "SPP and Bidirectional (PS/2)",	
+				     "EPP and SPP",
+				     "ECP",
+				     "ECP and EPP" };
+
+	outb(key,io);
+	outb(key,io);
+	outb(1,io);
+	cr1=inb(io+1);
+	outb(4,io);
+	cr4=inb(io+1);
+	outb(0x0a,io);
+	cra=inb(io+1);
+	outb(0x23,io);
+	cr23=inb(io+1);
+	outb(0x26,io);
+	cr26=inb(io+1);
+	outb(0x27,io);
+	cr27=inb(io+1);
+	outb(0xaa,io);
+
+	if (verbose_probing) {
+		printk (KERN_INFO "SMSC 37c669 LPT Config: cr_1=0x%02x, 4=0x%02x, "
+			"A=0x%2x, 23=0x%02x, 26=0x%02x, 27=0x%02x\n",
+			cr1,cr4,cra,cr23,cr26,cr27);
+		
+		/* The documentation calls DMA and IRQ-Lines by letters, so
+		   the board maker can/will wire them
+		   appropriately/randomly...  G=reserved H=IDE-irq, */
+		printk (KERN_INFO "SMSC LPT Config: io=0x%04x, irq=%c, dma=%c, "
+			"fifo threshold=%d\n", cr23*4,
+			(cr27 &0x0f) ? 'A'-1+(cr27 &0x0f): '-',
+			(cr26 &0x0f) ? 'A'-1+(cr26 &0x0f): '-', cra & 0x0f);
+		printk(KERN_INFO "SMSC LPT Config: enabled=%s power=%s\n",
+		       (cr23*4 >=0x100) ?"yes":"no", (cr1 & 4) ? "yes" : "no");
+		printk(KERN_INFO "SMSC LPT Config: Port mode=%s, EPP version =%s\n",
+		       (cr1 & 0x08 ) ? "Standard mode only (SPP)" : modes[cr4 & 0x03], 
+		       (cr4 & 0x40) ? "1.7" : "1.9");
+	}
+		
+	/* Heuristics !  BIOS setup for this mainboard device limits
+	   the choices to standard settings, i.e. io-address and IRQ
+	   are related, however DMA can be 1 or 3, assume DMA_A=DMA1,
+	   DMA_C=DMA3 (this is true e.g. for TYAN 1564D Tomcat IV) */
+	if(cr23*4 >=0x100) { /* if active */
+		while((superios[i].io!= 0) && (i<NR_SUPERIOS))
+			i++;
+		if(i==NR_SUPERIOS)
+			printk(KERN_INFO "Super-IO: too many chips!\n");
+		else {
+			int d;
+			switch (cr23*4) {
+				case 0x3bc:
+					superios[i].io = 0x3bc;
+					superios[i].irq = 7;
+					break;
+				case 0x378:
+					superios[i].io = 0x378;
+					superios[i].irq = 7;
+					break;
+				case 0x278:
+					superios[i].io = 0x278;
+					superios[i].irq = 5;
+			}
+			d=(cr26 &0x0f);
+			if((d==1) || (d==3)) 
+				superios[i].dma= d;
+			else
+				superios[i].dma= PARPORT_DMA_NONE;
+		}
+ 	}
+}
+
+
+static void __devinit show_parconfig_winbond(int io, int key)
+{
+	int cr30,cr60,cr61,cr70,cr74,crf0,i=0;
+	static const char *modes[] = {
+		"Standard (SPP) and Bidirectional(PS/2)", /* 0 */
+		"EPP-1.9 and SPP",
+		"ECP",
+		"ECP and EPP-1.9",
+		"Standard (SPP)",
+		"EPP-1.7 and SPP",		/* 5 */
+		"undefined!",
+		"ECP and EPP-1.7" };
+	static char *irqtypes[] = { "pulsed low, high-Z", "follows nACK" };
+		
+	/* The registers are called compatible-PnP because the
+           register layout is modelled after ISA-PnP, the access
+           method is just another ... */
+	outb(key,io);
+	outb(key,io);
+	outb(0x07,io);   /* Register 7: Select Logical Device */
+	outb(0x01,io+1); /* LD1 is Parallel Port */
+	outb(0x30,io);
+	cr30=inb(io+1);
+	outb(0x60,io);
+	cr60=inb(io+1);
+	outb(0x61,io);
+	cr61=inb(io+1);
+	outb(0x70,io);
+	cr70=inb(io+1);
+	outb(0x74,io);
+	cr74=inb(io+1);
+	outb(0xf0,io);
+	crf0=inb(io+1);
+	outb(0xaa,io);
+
+	if (verbose_probing) {
+		printk(KERN_INFO "Winbond LPT Config: cr_30=%02x 60,61=%02x%02x "
+		       "70=%02x 74=%02x, f0=%02x\n", cr30,cr60,cr61,cr70,cr74,crf0);
+		printk(KERN_INFO "Winbond LPT Config: active=%s, io=0x%02x%02x irq=%d, ", 
+		       (cr30 & 0x01) ? "yes":"no", cr60,cr61,cr70&0x0f );
+		if ((cr74 & 0x07) > 3)
+			printk("dma=none\n");
+		else
+			printk("dma=%d\n",cr74 & 0x07);
+		printk(KERN_INFO "Winbond LPT Config: irqtype=%s, ECP fifo threshold=%d\n",
+		       irqtypes[crf0>>7], (crf0>>3)&0x0f);
+		printk(KERN_INFO "Winbond LPT Config: Port mode=%s\n", modes[crf0 & 0x07]);
+	}
+
+	if(cr30 & 0x01) { /* the settings can be interrogated later ... */
+		while((superios[i].io!= 0) && (i<NR_SUPERIOS))
+			i++;
+		if(i==NR_SUPERIOS) 
+			printk(KERN_INFO "Super-IO: too many chips!\n");
+		else {
+			superios[i].io = (cr60<<8)|cr61;
+			superios[i].irq = cr70&0x0f;
+			superios[i].dma = (((cr74 & 0x07) > 3) ?
+					   PARPORT_DMA_NONE : (cr74 & 0x07));
+		}
+	}
+}
+
+static void __devinit decode_winbond(int efer, int key, int devid, int devrev, int oldid)
+{
+	const char *type = "unknown";
+	int id,progif=2;
+
+	if (devid == devrev)
+		/* simple heuristics, we happened to read some
+                   non-winbond register */
+		return;
+
+	id=(devid<<8) | devrev;
+
+	/* Values are from public data sheets pdf files, I can just
+           confirm 83977TF is correct :-) */
+	if      (id == 0x9771) type="83977F/AF";
+	else if (id == 0x9773) type="83977TF / SMSC 97w33x/97w34x";
+	else if (id == 0x9774) type="83977ATF";
+	else if ((id & ~0x0f) == 0x5270) type="83977CTF / SMSC 97w36x";
+	else if ((id & ~0x0f) == 0x52f0) type="83977EF / SMSC 97w35x";
+	else if ((id & ~0x0f) == 0x5210) type="83627";
+	else if ((id & ~0x0f) == 0x6010) type="83697HF";
+	else if ((oldid &0x0f ) == 0x0a) { type="83877F"; progif=1;}
+	else if ((oldid &0x0f ) == 0x0b) { type="83877AF"; progif=1;}
+	else if ((oldid &0x0f ) == 0x0c) { type="83877TF"; progif=1;}
+	else if ((oldid &0x0f ) == 0x0d) { type="83877ATF"; progif=1;}
+	else progif=0;
+
+	if (verbose_probing)
+		printk(KERN_INFO "Winbond chip at EFER=0x%x key=0x%02x "
+		       "devid=%02x devrev=%02x oldid=%02x type=%s\n", 
+		       efer, key, devid, devrev, oldid, type);
+
+	if (progif == 2)
+		show_parconfig_winbond(efer,key);
+}
+
+static void __devinit decode_smsc(int efer, int key, int devid, int devrev)
+{
+        const char *type = "unknown";
+	void (*func)(int io, int key);
+        int id;
+
+        if (devid == devrev)
+		/* simple heuristics, we happened to read some
+                   non-smsc register */
+		return;
+
+	func=NULL;
+        id=(devid<<8) | devrev;
+
+	if	(id==0x0302) {type="37c669"; func=show_parconfig_smsc37c669;}
+	else if	(id==0x6582) type="37c665IR";
+	else if	(devid==0x65) type="37c665GT";
+	else if	(devid==0x66) type="37c666GT";
+
+	if (verbose_probing)
+		printk(KERN_INFO "SMSC chip at EFER=0x%x "
+		       "key=0x%02x devid=%02x devrev=%02x type=%s\n",
+		       efer, key, devid, devrev, type);
+
+	if (func)
+		func(efer,key);
+}
+
+
+static void __devinit winbond_check(int io, int key)
+{
+	int devid,devrev,oldid,x_devid,x_devrev,x_oldid;
+
+	if (!request_region(io, 3, __FUNCTION__))
+		return;
+
+	/* First probe without key */
+	outb(0x20,io);
+	x_devid=inb(io+1);
+	outb(0x21,io);
+	x_devrev=inb(io+1);
+	outb(0x09,io);
+	x_oldid=inb(io+1);
+
+	outb(key,io);
+	outb(key,io);     /* Write Magic Sequence to EFER, extended
+                             funtion enable register */
+	outb(0x20,io);    /* Write EFIR, extended function index register */
+	devid=inb(io+1);  /* Read EFDR, extended function data register */
+	outb(0x21,io);
+	devrev=inb(io+1);
+	outb(0x09,io);
+	oldid=inb(io+1);
+	outb(0xaa,io);    /* Magic Seal */
+
+	if ((x_devid == devid) && (x_devrev == devrev) && (x_oldid == oldid))
+		goto out; /* protection against false positives */
+
+	decode_winbond(io,key,devid,devrev,oldid);
+out:
+	release_region(io, 3);
+}
+
+static void __devinit winbond_check2(int io,int key)
+{
+        int devid,devrev,oldid,x_devid,x_devrev,x_oldid;
+
+	if (!request_region(io, 3, __FUNCTION__))
+		return;
+
+	/* First probe without the key */
+	outb(0x20,io+2);
+	x_devid=inb(io+2);
+	outb(0x21,io+1);
+	x_devrev=inb(io+2);
+	outb(0x09,io+1);
+	x_oldid=inb(io+2);
+
+        outb(key,io);     /* Write Magic Byte to EFER, extended
+                             funtion enable register */
+        outb(0x20,io+2);  /* Write EFIR, extended function index register */
+        devid=inb(io+2);  /* Read EFDR, extended function data register */
+        outb(0x21,io+1);
+        devrev=inb(io+2);
+        outb(0x09,io+1);
+        oldid=inb(io+2);
+        outb(0xaa,io);    /* Magic Seal */
+
+	if ((x_devid == devid) && (x_devrev == devrev) && (x_oldid == oldid))
+		goto out; /* protection against false positives */
+
+	decode_winbond(io,key,devid,devrev,oldid);
+out:
+	release_region(io, 3);
+}
+
+static void __devinit smsc_check(int io, int key)
+{
+        int id,rev,oldid,oldrev,x_id,x_rev,x_oldid,x_oldrev;
+
+	if (!request_region(io, 3, __FUNCTION__))
+		return;
+
+	/* First probe without the key */
+	outb(0x0d,io);
+	x_oldid=inb(io+1);
+	outb(0x0e,io);
+	x_oldrev=inb(io+1);
+	outb(0x20,io);
+	x_id=inb(io+1);
+	outb(0x21,io);
+	x_rev=inb(io+1);
+
+        outb(key,io);
+        outb(key,io);     /* Write Magic Sequence to EFER, extended
+                             funtion enable register */
+        outb(0x0d,io);    /* Write EFIR, extended function index register */
+        oldid=inb(io+1);  /* Read EFDR, extended function data register */
+        outb(0x0e,io);
+        oldrev=inb(io+1);
+	outb(0x20,io);
+	id=inb(io+1);
+	outb(0x21,io);
+	rev=inb(io+1);
+        outb(0xaa,io);    /* Magic Seal */
+
+	if ((x_id == id) && (x_oldrev == oldrev) &&
+	    (x_oldid == oldid) && (x_rev == rev))
+		goto out; /* protection against false positives */
+
+        decode_smsc(io,key,oldid,oldrev);
+out:
+	release_region(io, 3);
+}
+
+
+static void __devinit detect_and_report_winbond (void)
+{ 
+	if (verbose_probing)
+		printk(KERN_DEBUG "Winbond Super-IO detection, now testing ports 3F0,370,250,4E,2E ...\n");
+	winbond_check(0x3f0,0x87);
+	winbond_check(0x370,0x87);
+	winbond_check(0x2e ,0x87);
+	winbond_check(0x4e ,0x87);
+	winbond_check(0x3f0,0x86);
+	winbond_check2(0x250,0x88); 
+	winbond_check2(0x250,0x89);
+}
+
+static void __devinit detect_and_report_smsc (void)
+{
+	if (verbose_probing)
+		printk(KERN_DEBUG "SMSC Super-IO detection, now testing Ports 2F0, 370 ...\n");
+	smsc_check(0x3f0,0x55);
+	smsc_check(0x370,0x55);
+	smsc_check(0x3f0,0x44);
+	smsc_check(0x370,0x44);
+}
+#endif /* CONFIG_PARPORT_PC_SUPERIO */
+
+static int __devinit get_superio_dma (struct parport *p)
+{
+	int i=0;
+	while( (superios[i].io != p->base) && (i<NR_SUPERIOS))
+		i++;
+	if (i!=NR_SUPERIOS)
+		return superios[i].dma;
+	return PARPORT_DMA_NONE;
+}
+
+static int __devinit get_superio_irq (struct parport *p)
+{
+	int i=0;
+        while( (superios[i].io != p->base) && (i<NR_SUPERIOS))
+                i++;
+        if (i!=NR_SUPERIOS)
+                return superios[i].irq;
+        return PARPORT_IRQ_NONE;
+}
+	
+
+/* --- Mode detection ------------------------------------- */
+
+/*
+ * Checks for port existence, all ports support SPP MODE
+ * Returns: 
+ *         0           :  No parallel port at this address
+ *  PARPORT_MODE_PCSPP :  SPP port detected 
+ *                        (if the user specified an ioport himself,
+ *                         this shall always be the case!)
+ *
+ */
+static int __devinit parport_SPP_supported(struct parport *pb)
+{
+	unsigned char r, w;
+
+	/*
+	 * first clear an eventually pending EPP timeout 
+	 * I (sailer@ife.ee.ethz.ch) have an SMSC chipset
+	 * that does not even respond to SPP cycles if an EPP
+	 * timeout is pending
+	 */
+	clear_epp_timeout(pb);
+
+	/* Do a simple read-write test to make sure the port exists. */
+	w = 0xc;
+	outb (w, CONTROL (pb));
+
+	/* Is there a control register that we can read from?  Some
+	 * ports don't allow reads, so read_control just returns a
+	 * software copy. Some ports _do_ allow reads, so bypass the
+	 * software copy here.  In addition, some bits aren't
+	 * writable. */
+	r = inb (CONTROL (pb));
+	if ((r & 0xf) == w) {
+		w = 0xe;
+		outb (w, CONTROL (pb));
+		r = inb (CONTROL (pb));
+		outb (0xc, CONTROL (pb));
+		if ((r & 0xf) == w)
+			return PARPORT_MODE_PCSPP;
+	}
+
+	if (user_specified)
+		/* That didn't work, but the user thinks there's a
+		 * port here. */
+		printk (KERN_INFO "parport 0x%lx (WARNING): CTR: "
+			"wrote 0x%02x, read 0x%02x\n", pb->base, w, r);
+
+	/* Try the data register.  The data lines aren't tri-stated at
+	 * this stage, so we expect back what we wrote. */
+	w = 0xaa;
+	parport_pc_write_data (pb, w);
+	r = parport_pc_read_data (pb);
+	if (r == w) {
+		w = 0x55;
+		parport_pc_write_data (pb, w);
+		r = parport_pc_read_data (pb);
+		if (r == w)
+			return PARPORT_MODE_PCSPP;
+	}
+
+	if (user_specified) {
+		/* Didn't work, but the user is convinced this is the
+		 * place. */
+		printk (KERN_INFO "parport 0x%lx (WARNING): DATA: "
+			"wrote 0x%02x, read 0x%02x\n", pb->base, w, r);
+		printk (KERN_INFO "parport 0x%lx: You gave this address, "
+			"but there is probably no parallel port there!\n",
+			pb->base);
+	}
+
+	/* It's possible that we can't read the control register or
+	 * the data register.  In that case just believe the user. */
+	if (user_specified)
+		return PARPORT_MODE_PCSPP;
+
+	return 0;
+}
+
+/* Check for ECR
+ *
+ * Old style XT ports alias io ports every 0x400, hence accessing ECR
+ * on these cards actually accesses the CTR.
+ *
+ * Modern cards don't do this but reading from ECR will return 0xff
+ * regardless of what is written here if the card does NOT support
+ * ECP.
+ *
+ * We first check to see if ECR is the same as CTR.  If not, the low
+ * two bits of ECR aren't writable, so we check by writing ECR and
+ * reading it back to see if it's what we expect.
+ */
+static int __devinit parport_ECR_present(struct parport *pb)
+{
+	struct parport_pc_private *priv = pb->private_data;
+	unsigned char r = 0xc;
+
+	outb (r, CONTROL (pb));
+	if ((inb (ECONTROL (pb)) & 0x3) == (r & 0x3)) {
+		outb (r ^ 0x2, CONTROL (pb)); /* Toggle bit 1 */
+
+		r = inb (CONTROL (pb));
+		if ((inb (ECONTROL (pb)) & 0x2) == (r & 0x2))
+			goto no_reg; /* Sure that no ECR register exists */
+	}
+	
+	if ((inb (ECONTROL (pb)) & 0x3 ) != 0x1)
+		goto no_reg;
+
+	ECR_WRITE (pb, 0x34);
+	if (inb (ECONTROL (pb)) != 0x35)
+		goto no_reg;
+
+	priv->ecr = 1;
+	outb (0xc, CONTROL (pb));
+	
+	/* Go to mode 000 */
+	frob_set_mode (pb, ECR_SPP);
+
+	return 1;
+
+ no_reg:
+	outb (0xc, CONTROL (pb));
+	return 0; 
+}
+
+#ifdef CONFIG_PARPORT_1284
+/* Detect PS/2 support.
+ *
+ * Bit 5 (0x20) sets the PS/2 data direction; setting this high
+ * allows us to read data from the data lines.  In theory we would get back
+ * 0xff but any peripheral attached to the port may drag some or all of the
+ * lines down to zero.  So if we get back anything that isn't the contents
+ * of the data register we deem PS/2 support to be present. 
+ *
+ * Some SPP ports have "half PS/2" ability - you can't turn off the line
+ * drivers, but an external peripheral with sufficiently beefy drivers of
+ * its own can overpower them and assert its own levels onto the bus, from
+ * where they can then be read back as normal.  Ports with this property
+ * and the right type of device attached are likely to fail the SPP test,
+ * (as they will appear to have stuck bits) and so the fact that they might
+ * be misdetected here is rather academic. 
+ */
+
+static int __devinit parport_PS2_supported(struct parport *pb)
+{
+	int ok = 0;
+  
+	clear_epp_timeout(pb);
+
+	/* try to tri-state the buffer */
+	parport_pc_data_reverse (pb);
+	
+	parport_pc_write_data(pb, 0x55);
+	if (parport_pc_read_data(pb) != 0x55) ok++;
+
+	parport_pc_write_data(pb, 0xaa);
+	if (parport_pc_read_data(pb) != 0xaa) ok++;
+
+	/* cancel input mode */
+	parport_pc_data_forward (pb);
+
+	if (ok) {
+		pb->modes |= PARPORT_MODE_TRISTATE;
+	} else {
+		struct parport_pc_private *priv = pb->private_data;
+		priv->ctr_writable &= ~0x20;
+	}
+
+	return ok;
+}
+
+#ifdef CONFIG_PARPORT_PC_FIFO
+static int __devinit parport_ECP_supported(struct parport *pb)
+{
+	int i;
+	int config, configb;
+	int pword;
+	struct parport_pc_private *priv = pb->private_data;
+	/* Translate ECP intrLine to ISA irq value */	
+	static const int intrline[]= { 0, 7, 9, 10, 11, 14, 15, 5 }; 
+
+	/* If there is no ECR, we have no hope of supporting ECP. */
+	if (!priv->ecr)
+		return 0;
+
+	/* Find out FIFO depth */
+	ECR_WRITE (pb, ECR_SPP << 5); /* Reset FIFO */
+	ECR_WRITE (pb, ECR_TST << 5); /* TEST FIFO */
+	for (i=0; i < 1024 && !(inb (ECONTROL (pb)) & 0x02); i++)
+		outb (0xaa, FIFO (pb));
+
+	/*
+	 * Using LGS chipset it uses ECR register, but
+	 * it doesn't support ECP or FIFO MODE
+	 */
+	if (i == 1024) {
+		ECR_WRITE (pb, ECR_SPP << 5);
+		return 0;
+	}
+
+	priv->fifo_depth = i;
+	if (verbose_probing)
+		printk (KERN_DEBUG "0x%lx: FIFO is %d bytes\n", pb->base, i);
+
+	/* Find out writeIntrThreshold */
+	frob_econtrol (pb, 1<<2, 1<<2);
+	frob_econtrol (pb, 1<<2, 0);
+	for (i = 1; i <= priv->fifo_depth; i++) {
+		inb (FIFO (pb));
+		udelay (50);
+		if (inb (ECONTROL (pb)) & (1<<2))
+			break;
+	}
+
+	if (i <= priv->fifo_depth) {
+		if (verbose_probing)
+			printk (KERN_DEBUG "0x%lx: writeIntrThreshold is %d\n",
+				pb->base, i);
+	} else
+		/* Number of bytes we know we can write if we get an
+                   interrupt. */
+		i = 0;
+
+	priv->writeIntrThreshold = i;
+
+	/* Find out readIntrThreshold */
+	frob_set_mode (pb, ECR_PS2); /* Reset FIFO and enable PS2 */
+	parport_pc_data_reverse (pb); /* Must be in PS2 mode */
+	frob_set_mode (pb, ECR_TST); /* Test FIFO */
+	frob_econtrol (pb, 1<<2, 1<<2);
+	frob_econtrol (pb, 1<<2, 0);
+	for (i = 1; i <= priv->fifo_depth; i++) {
+		outb (0xaa, FIFO (pb));
+		if (inb (ECONTROL (pb)) & (1<<2))
+			break;
+	}
+
+	if (i <= priv->fifo_depth) {
+		if (verbose_probing)
+			printk (KERN_INFO "0x%lx: readIntrThreshold is %d\n",
+				pb->base, i);
+	} else
+		/* Number of bytes we can read if we get an interrupt. */
+		i = 0;
+
+	priv->readIntrThreshold = i;
+
+	ECR_WRITE (pb, ECR_SPP << 5); /* Reset FIFO */
+	ECR_WRITE (pb, 0xf4); /* Configuration mode */
+	config = inb (CONFIGA (pb));
+	pword = (config >> 4) & 0x7;
+	switch (pword) {
+	case 0:
+		pword = 2;
+		printk (KERN_WARNING "0x%lx: Unsupported pword size!\n",
+			pb->base);
+		break;
+	case 2:
+		pword = 4;
+		printk (KERN_WARNING "0x%lx: Unsupported pword size!\n",
+			pb->base);
+		break;
+	default:
+		printk (KERN_WARNING "0x%lx: Unknown implementation ID\n",
+			pb->base);
+		/* Assume 1 */
+	case 1:
+		pword = 1;
+	}
+	priv->pword = pword;
+
+	if (verbose_probing) {
+		printk (KERN_DEBUG "0x%lx: PWord is %d bits\n", pb->base, 8 * pword);
+		
+		printk (KERN_DEBUG "0x%lx: Interrupts are ISA-%s\n", pb->base,
+			config & 0x80 ? "Level" : "Pulses");
+
+		configb = inb (CONFIGB (pb));
+		printk (KERN_DEBUG "0x%lx: ECP port cfgA=0x%02x cfgB=0x%02x\n",
+			pb->base, config, configb);
+		printk (KERN_DEBUG "0x%lx: ECP settings irq=", pb->base);
+		if ((configb >>3) & 0x07)
+			printk("%d",intrline[(configb >>3) & 0x07]);
+		else
+			printk("<none or set by other means>");
+		printk (" dma=");
+		if( (configb & 0x03 ) == 0x00)
+			printk("<none or set by other means>\n");
+		else
+			printk("%d\n",configb & 0x07);
+	}
+
+	/* Go back to mode 000 */
+	frob_set_mode (pb, ECR_SPP);
+
+	return 1;
+}
+#endif
+
+static int __devinit parport_ECPPS2_supported(struct parport *pb)
+{
+	const struct parport_pc_private *priv = pb->private_data;
+	int result;
+	unsigned char oecr;
+
+	if (!priv->ecr)
+		return 0;
+
+	oecr = inb (ECONTROL (pb));
+	ECR_WRITE (pb, ECR_PS2 << 5);
+	result = parport_PS2_supported(pb);
+	ECR_WRITE (pb, oecr);
+	return result;
+}
+
+/* EPP mode detection  */
+
+static int __devinit parport_EPP_supported(struct parport *pb)
+{
+	const struct parport_pc_private *priv = pb->private_data;
+
+	/*
+	 * Theory:
+	 *	Bit 0 of STR is the EPP timeout bit, this bit is 0
+	 *	when EPP is possible and is set high when an EPP timeout
+	 *	occurs (EPP uses the HALT line to stop the CPU while it does
+	 *	the byte transfer, an EPP timeout occurs if the attached
+	 *	device fails to respond after 10 micro seconds).
+	 *
+	 *	This bit is cleared by either reading it (National Semi)
+	 *	or writing a 1 to the bit (SMC, UMC, WinBond), others ???
+	 *	This bit is always high in non EPP modes.
+	 */
+
+	/* If EPP timeout bit clear then EPP available */
+	if (!clear_epp_timeout(pb)) {
+		return 0;  /* No way to clear timeout */
+	}
+
+	/* Check for Intel bug. */
+	if (priv->ecr) {
+		unsigned char i;
+		for (i = 0x00; i < 0x80; i += 0x20) {
+			ECR_WRITE (pb, i);
+			if (clear_epp_timeout (pb)) {
+				/* Phony EPP in ECP. */
+				return 0;
+			}
+		}
+	}
+
+	pb->modes |= PARPORT_MODE_EPP;
+
+	/* Set up access functions to use EPP hardware. */
+	pb->ops->epp_read_data = parport_pc_epp_read_data;
+	pb->ops->epp_write_data = parport_pc_epp_write_data;
+	pb->ops->epp_read_addr = parport_pc_epp_read_addr;
+	pb->ops->epp_write_addr = parport_pc_epp_write_addr;
+
+	return 1;
+}
+
+static int __devinit parport_ECPEPP_supported(struct parport *pb)
+{
+	struct parport_pc_private *priv = pb->private_data;
+	int result;
+	unsigned char oecr;
+
+	if (!priv->ecr) {
+		return 0;
+	}
+
+	oecr = inb (ECONTROL (pb));
+	/* Search for SMC style EPP+ECP mode */
+	ECR_WRITE (pb, 0x80);
+	outb (0x04, CONTROL (pb));
+	result = parport_EPP_supported(pb);
+
+	ECR_WRITE (pb, oecr);
+
+	if (result) {
+		/* Set up access functions to use ECP+EPP hardware. */
+		pb->ops->epp_read_data = parport_pc_ecpepp_read_data;
+		pb->ops->epp_write_data = parport_pc_ecpepp_write_data;
+		pb->ops->epp_read_addr = parport_pc_ecpepp_read_addr;
+		pb->ops->epp_write_addr = parport_pc_ecpepp_write_addr;
+	}
+
+	return result;
+}
+
+#else /* No IEEE 1284 support */
+
+/* Don't bother probing for modes we know we won't use. */
+static int __devinit parport_PS2_supported(struct parport *pb) { return 0; }
+#ifdef CONFIG_PARPORT_PC_FIFO
+static int __devinit parport_ECP_supported(struct parport *pb) { return 0; }
+#endif
+static int __devinit parport_EPP_supported(struct parport *pb) { return 0; }
+static int __devinit parport_ECPEPP_supported(struct parport *pb){return 0;}
+static int __devinit parport_ECPPS2_supported(struct parport *pb){return 0;}
+
+#endif /* No IEEE 1284 support */
+
+/* --- IRQ detection -------------------------------------- */
+
+/* Only if supports ECP mode */
+static int __devinit programmable_irq_support(struct parport *pb)
+{
+	int irq, intrLine;
+	unsigned char oecr = inb (ECONTROL (pb));
+	static const int lookup[8] = {
+		PARPORT_IRQ_NONE, 7, 9, 10, 11, 14, 15, 5
+	};
+
+	ECR_WRITE (pb, ECR_CNF << 5); /* Configuration MODE */
+
+	intrLine = (inb (CONFIGB (pb)) >> 3) & 0x07;
+	irq = lookup[intrLine];
+
+	ECR_WRITE (pb, oecr);
+	return irq;
+}
+
+static int __devinit irq_probe_ECP(struct parport *pb)
+{
+	int i;
+	unsigned long irqs;
+
+	irqs = probe_irq_on();
+		
+	ECR_WRITE (pb, ECR_SPP << 5); /* Reset FIFO */
+	ECR_WRITE (pb, (ECR_TST << 5) | 0x04);
+	ECR_WRITE (pb, ECR_TST << 5);
+
+	/* If Full FIFO sure that writeIntrThreshold is generated */
+	for (i=0; i < 1024 && !(inb (ECONTROL (pb)) & 0x02) ; i++) 
+		outb (0xaa, FIFO (pb));
+		
+	pb->irq = probe_irq_off(irqs);
+	ECR_WRITE (pb, ECR_SPP << 5);
+
+	if (pb->irq <= 0)
+		pb->irq = PARPORT_IRQ_NONE;
+
+	return pb->irq;
+}
+
+/*
+ * This detection seems that only works in National Semiconductors
+ * This doesn't work in SMC, LGS, and Winbond 
+ */
+static int __devinit irq_probe_EPP(struct parport *pb)
+{
+#ifndef ADVANCED_DETECT
+	return PARPORT_IRQ_NONE;
+#else
+	int irqs;
+	unsigned char oecr;
+
+	if (pb->modes & PARPORT_MODE_PCECR)
+		oecr = inb (ECONTROL (pb));
+
+	irqs = probe_irq_on();
+
+	if (pb->modes & PARPORT_MODE_PCECR)
+		frob_econtrol (pb, 0x10, 0x10);
+	
+	clear_epp_timeout(pb);
+	parport_pc_frob_control (pb, 0x20, 0x20);
+	parport_pc_frob_control (pb, 0x10, 0x10);
+	clear_epp_timeout(pb);
+
+	/* Device isn't expecting an EPP read
+	 * and generates an IRQ.
+	 */
+	parport_pc_read_epp(pb);
+	udelay(20);
+
+	pb->irq = probe_irq_off (irqs);
+	if (pb->modes & PARPORT_MODE_PCECR)
+		ECR_WRITE (pb, oecr);
+	parport_pc_write_control(pb, 0xc);
+
+	if (pb->irq <= 0)
+		pb->irq = PARPORT_IRQ_NONE;
+
+	return pb->irq;
+#endif /* Advanced detection */
+}
+
+static int __devinit irq_probe_SPP(struct parport *pb)
+{
+	/* Don't even try to do this. */
+	return PARPORT_IRQ_NONE;
+}
+
+/* We will attempt to share interrupt requests since other devices
+ * such as sound cards and network cards seem to like using the
+ * printer IRQs.
+ *
+ * When ECP is available we can autoprobe for IRQs.
+ * NOTE: If we can autoprobe it, we can register the IRQ.
+ */
+static int __devinit parport_irq_probe(struct parport *pb)
+{
+	struct parport_pc_private *priv = pb->private_data;
+
+	if (priv->ecr) {
+		pb->irq = programmable_irq_support(pb);
+
+		if (pb->irq == PARPORT_IRQ_NONE)
+			pb->irq = irq_probe_ECP(pb);
+	}
+
+	if ((pb->irq == PARPORT_IRQ_NONE) && priv->ecr &&
+	    (pb->modes & PARPORT_MODE_EPP))
+		pb->irq = irq_probe_EPP(pb);
+
+	clear_epp_timeout(pb);
+
+	if (pb->irq == PARPORT_IRQ_NONE && (pb->modes & PARPORT_MODE_EPP))
+		pb->irq = irq_probe_EPP(pb);
+
+	clear_epp_timeout(pb);
+
+	if (pb->irq == PARPORT_IRQ_NONE)
+		pb->irq = irq_probe_SPP(pb);
+
+	if (pb->irq == PARPORT_IRQ_NONE)
+		pb->irq = get_superio_irq(pb);
+
+	return pb->irq;
+}
+
+/* --- DMA detection -------------------------------------- */
+
+/* Only if chipset conforms to ECP ISA Interface Standard */
+static int __devinit programmable_dma_support (struct parport *p)
+{
+	unsigned char oecr = inb (ECONTROL (p));
+	int dma;
+
+	frob_set_mode (p, ECR_CNF);
+	
+	dma = inb (CONFIGB(p)) & 0x07;
+	/* 000: Indicates jumpered 8-bit DMA if read-only.
+	   100: Indicates jumpered 16-bit DMA if read-only. */
+	if ((dma & 0x03) == 0)
+		dma = PARPORT_DMA_NONE;
+
+	ECR_WRITE (p, oecr);
+	return dma;
+}
+
+static int __devinit parport_dma_probe (struct parport *p)
+{
+	const struct parport_pc_private *priv = p->private_data;
+	if (priv->ecr)
+		p->dma = programmable_dma_support(p); /* ask ECP chipset first */
+	if (p->dma == PARPORT_DMA_NONE) {
+		/* ask known Super-IO chips proper, although these
+		   claim ECP compatible, some don't report their DMA
+		   conforming to ECP standards */
+		p->dma = get_superio_dma(p);
+	}
+
+	return p->dma;
+}
+
+/* --- Initialisation code -------------------------------- */
+
+static LIST_HEAD(ports_list);
+static DEFINE_SPINLOCK(ports_lock);
+
+struct parport *parport_pc_probe_port (unsigned long int base,
+				       unsigned long int base_hi,
+				       int irq, int dma,
+				       struct pci_dev *dev)
+{
+	struct parport_pc_private *priv;
+	struct parport_operations *ops;
+	struct parport *p;
+	int probedirq = PARPORT_IRQ_NONE;
+	struct resource *base_res;
+	struct resource	*ECR_res = NULL;
+	struct resource	*EPP_res = NULL;
+
+	ops = kmalloc(sizeof (struct parport_operations), GFP_KERNEL);
+	if (!ops)
+		goto out1;
+
+	priv = kmalloc (sizeof (struct parport_pc_private), GFP_KERNEL);
+	if (!priv)
+		goto out2;
+
+	/* a misnomer, actually - it's allocate and reserve parport number */
+	p = parport_register_port(base, irq, dma, ops);
+	if (!p)
+		goto out3;
+
+	base_res = request_region(base, 3, p->name);
+	if (!base_res)
+		goto out4;
+
+	memcpy(ops, &parport_pc_ops, sizeof (struct parport_operations));
+	priv->ctr = 0xc;
+	priv->ctr_writable = ~0x10;
+	priv->ecr = 0;
+	priv->fifo_depth = 0;
+	priv->dma_buf = NULL;
+	priv->dma_handle = 0;
+	priv->dev = dev;
+	INIT_LIST_HEAD(&priv->list);
+	priv->port = p;
+	p->base_hi = base_hi;
+	p->modes = PARPORT_MODE_PCSPP | PARPORT_MODE_SAFEININT;
+	p->private_data = priv;
+
+	if (base_hi) {
+		ECR_res = request_region(base_hi, 3, p->name);
+		if (ECR_res)
+			parport_ECR_present(p);
+	}
+
+	if (base != 0x3bc) {
+		EPP_res = request_region(base+0x3, 5, p->name);
+		if (EPP_res)
+			if (!parport_EPP_supported(p))
+				parport_ECPEPP_supported(p);
+	}
+	if (!parport_SPP_supported (p))
+		/* No port. */
+		goto out5;
+	if (priv->ecr)
+		parport_ECPPS2_supported(p);
+	else
+		parport_PS2_supported(p);
+
+	p->size = (p->modes & PARPORT_MODE_EPP)?8:3;
+
+	printk(KERN_INFO "%s: PC-style at 0x%lx", p->name, p->base);
+	if (p->base_hi && priv->ecr)
+		printk(" (0x%lx)", p->base_hi);
+	if (p->irq == PARPORT_IRQ_AUTO) {
+		p->irq = PARPORT_IRQ_NONE;
+		parport_irq_probe(p);
+	} else if (p->irq == PARPORT_IRQ_PROBEONLY) {
+		p->irq = PARPORT_IRQ_NONE;
+		parport_irq_probe(p);
+		probedirq = p->irq;
+		p->irq = PARPORT_IRQ_NONE;
+	}
+	if (p->irq != PARPORT_IRQ_NONE) {
+		printk(", irq %d", p->irq);
+		priv->ctr_writable |= 0x10;
+
+		if (p->dma == PARPORT_DMA_AUTO) {
+			p->dma = PARPORT_DMA_NONE;
+			parport_dma_probe(p);
+		}
+	}
+	if (p->dma == PARPORT_DMA_AUTO) /* To use DMA, giving the irq
+                                           is mandatory (see above) */
+		p->dma = PARPORT_DMA_NONE;
+
+#ifdef CONFIG_PARPORT_PC_FIFO
+	if (parport_ECP_supported(p) &&
+	    p->dma != PARPORT_DMA_NOFIFO &&
+	    priv->fifo_depth > 0 && p->irq != PARPORT_IRQ_NONE) {
+		p->modes |= PARPORT_MODE_ECP | PARPORT_MODE_COMPAT;
+		p->ops->compat_write_data = parport_pc_compat_write_block_pio;
+#ifdef CONFIG_PARPORT_1284
+		p->ops->ecp_write_data = parport_pc_ecp_write_block_pio;
+		/* currently broken, but working on it.. (FB) */
+		/* p->ops->ecp_read_data = parport_pc_ecp_read_block_pio; */
+#endif /* IEEE 1284 support */
+		if (p->dma != PARPORT_DMA_NONE) {
+			printk(", dma %d", p->dma);
+			p->modes |= PARPORT_MODE_DMA;
+		}
+		else printk(", using FIFO");
+	}
+	else
+		/* We can't use the DMA channel after all. */
+		p->dma = PARPORT_DMA_NONE;
+#endif /* Allowed to use FIFO/DMA */
+
+	printk(" [");
+#define printmode(x) {if(p->modes&PARPORT_MODE_##x){printk("%s%s",f?",":"",#x);f++;}}
+	{
+		int f = 0;
+		printmode(PCSPP);
+		printmode(TRISTATE);
+		printmode(COMPAT)
+		printmode(EPP);
+		printmode(ECP);
+		printmode(DMA);
+	}
+#undef printmode
+#ifndef CONFIG_PARPORT_1284
+	printk ("(,...)");
+#endif /* CONFIG_PARPORT_1284 */
+	printk("]\n");
+	if (probedirq != PARPORT_IRQ_NONE) 
+		printk(KERN_INFO "%s: irq %d detected\n", p->name, probedirq);
+
+	/* If No ECP release the ports grabbed above. */
+	if (ECR_res && (p->modes & PARPORT_MODE_ECP) == 0) {
+		release_region(base_hi, 3);
+		ECR_res = NULL;
+	}
+	/* Likewise for EEP ports */
+	if (EPP_res && (p->modes & PARPORT_MODE_EPP) == 0) {
+		release_region(base+3, 5);
+		EPP_res = NULL;
+	}
+	if (p->irq != PARPORT_IRQ_NONE) {
+		if (request_irq (p->irq, parport_pc_interrupt,
+				 0, p->name, p)) {
+			printk (KERN_WARNING "%s: irq %d in use, "
+				"resorting to polled operation\n",
+				p->name, p->irq);
+			p->irq = PARPORT_IRQ_NONE;
+			p->dma = PARPORT_DMA_NONE;
+		}
+
+#ifdef CONFIG_PARPORT_PC_FIFO
+		if (p->dma != PARPORT_DMA_NONE) {
+			if (request_dma (p->dma, p->name)) {
+				printk (KERN_WARNING "%s: dma %d in use, "
+					"resorting to PIO operation\n",
+					p->name, p->dma);
+				p->dma = PARPORT_DMA_NONE;
+			} else {
+				priv->dma_buf =
+				  pci_alloc_consistent(priv->dev,
+						       PAGE_SIZE,
+						       &priv->dma_handle);
+				if (! priv->dma_buf) {
+					printk (KERN_WARNING "%s: "
+						"cannot get buffer for DMA, "
+						"resorting to PIO operation\n",
+						p->name);
+					free_dma(p->dma);
+					p->dma = PARPORT_DMA_NONE;
+				}
+			}
+		}
+#endif /* CONFIG_PARPORT_PC_FIFO */
+	}
+
+	/* Done probing.  Now put the port into a sensible start-up state. */
+	if (priv->ecr)
+		/*
+		 * Put the ECP detected port in PS2 mode.
+		 * Do this also for ports that have ECR but don't do ECP.
+		 */
+		ECR_WRITE (p, 0x34);
+
+	parport_pc_write_data(p, 0);
+	parport_pc_data_forward (p);
+
+	/* Now that we've told the sharing engine about the port, and
+	   found out its characteristics, let the high-level drivers
+	   know about it. */
+	spin_lock(&ports_lock);
+	list_add(&priv->list, &ports_list);
+	spin_unlock(&ports_lock);
+	parport_announce_port (p);
+
+	return p;
+
+out5:
+	if (ECR_res)
+		release_region(base_hi, 3);
+	if (EPP_res)
+		release_region(base+0x3, 5);
+	release_region(base, 3);
+out4:
+	parport_put_port(p);
+out3:
+	kfree (priv);
+out2:
+	kfree (ops);
+out1:
+	return NULL;
+}
+
+EXPORT_SYMBOL (parport_pc_probe_port);
+
+void parport_pc_unregister_port (struct parport *p)
+{
+	struct parport_pc_private *priv = p->private_data;
+	struct parport_operations *ops = p->ops;
+
+	parport_remove_port(p);
+	spin_lock(&ports_lock);
+	list_del_init(&priv->list);
+	spin_unlock(&ports_lock);
+	if (p->dma != PARPORT_DMA_NONE)
+		free_dma(p->dma);
+	if (p->irq != PARPORT_IRQ_NONE)
+		free_irq(p->irq, p);
+	release_region(p->base, 3);
+	if (p->size > 3)
+		release_region(p->base + 3, p->size - 3);
+	if (p->modes & PARPORT_MODE_ECP)
+		release_region(p->base_hi, 3);
+#ifdef CONFIG_PARPORT_PC_FIFO
+	if (priv->dma_buf)
+		pci_free_consistent(priv->dev, PAGE_SIZE,
+				    priv->dma_buf,
+				    priv->dma_handle);
+#endif /* CONFIG_PARPORT_PC_FIFO */
+	kfree (p->private_data);
+	parport_put_port(p);
+	kfree (ops); /* hope no-one cached it */
+}
+
+EXPORT_SYMBOL (parport_pc_unregister_port);
+
+#ifdef CONFIG_PCI
+
+/* ITE support maintained by Rich Liu <richliu@poorman.org> */
+static int __devinit sio_ite_8872_probe (struct pci_dev *pdev, int autoirq,
+					 int autodma, struct parport_pc_via_data *via)
+{
+	short inta_addr[6] = { 0x2A0, 0x2C0, 0x220, 0x240, 0x1E0 };
+	struct resource *base_res;
+	u32 ite8872set;
+	u32 ite8872_lpt, ite8872_lpthi;
+	u8 ite8872_irq, type;
+	char *fake_name = "parport probe";
+	int irq;
+	int i;
+
+	DPRINTK (KERN_DEBUG "sio_ite_8872_probe()\n");
+	
+	// make sure which one chip
+	for(i = 0; i < 5; i++) {
+		base_res = request_region(inta_addr[i], 0x8, fake_name);
+		if (base_res) {
+			int test;
+			pci_write_config_dword (pdev, 0x60,
+						0xe7000000 | inta_addr[i]);
+			pci_write_config_dword (pdev, 0x78,
+						0x00000000 | inta_addr[i]);
+			test = inb (inta_addr[i]);
+			if (test != 0xff) break;
+			release_region(inta_addr[i], 0x8);
+		}
+	}
+	if(i >= 5) {
+		printk (KERN_INFO "parport_pc: cannot find ITE8872 INTA\n");
+		return 0;
+	}
+
+	type = inb (inta_addr[i] + 0x18);
+	type &= 0x0f;
+
+	switch (type) {
+	case 0x2:
+		printk (KERN_INFO "parport_pc: ITE8871 found (1P)\n");
+		ite8872set = 0x64200000;
+		break;
+	case 0xa:
+		printk (KERN_INFO "parport_pc: ITE8875 found (1P)\n");
+		ite8872set = 0x64200000;
+		break;
+	case 0xe:
+		printk (KERN_INFO "parport_pc: ITE8872 found (2S1P)\n");
+		ite8872set = 0x64e00000;
+		break;
+	case 0x6:
+		printk (KERN_INFO "parport_pc: ITE8873 found (1S)\n");
+		return 0;
+	case 0x8:
+		DPRINTK (KERN_DEBUG "parport_pc: ITE8874 found (2S)\n");
+		return 0;
+	default:
+		printk (KERN_INFO "parport_pc: unknown ITE887x\n");
+		printk (KERN_INFO "parport_pc: please mail 'lspci -nvv' "
+			"output to Rich.Liu@ite.com.tw\n");
+		return 0;
+	}
+
+	pci_read_config_byte (pdev, 0x3c, &ite8872_irq);
+	pci_read_config_dword (pdev, 0x1c, &ite8872_lpt);
+	ite8872_lpt &= 0x0000ff00;
+	pci_read_config_dword (pdev, 0x20, &ite8872_lpthi);
+	ite8872_lpthi &= 0x0000ff00;
+	pci_write_config_dword (pdev, 0x6c, 0xe3000000 | ite8872_lpt);
+	pci_write_config_dword (pdev, 0x70, 0xe3000000 | ite8872_lpthi);
+	pci_write_config_dword (pdev, 0x80, (ite8872_lpthi<<16) | ite8872_lpt);
+	// SET SPP&EPP , Parallel Port NO DMA , Enable All Function
+	// SET Parallel IRQ
+	pci_write_config_dword (pdev, 0x9c,
+				ite8872set | (ite8872_irq * 0x11111));
+
+	DPRINTK (KERN_DEBUG "ITE887x: The IRQ is %d.\n", ite8872_irq);
+	DPRINTK (KERN_DEBUG "ITE887x: The PARALLEL I/O port is 0x%x.\n",
+		 ite8872_lpt);
+	DPRINTK (KERN_DEBUG "ITE887x: The PARALLEL I/O porthi is 0x%x.\n",
+		 ite8872_lpthi);
+
+	/* Let the user (or defaults) steer us away from interrupts */
+	irq = ite8872_irq;
+	if (autoirq != PARPORT_IRQ_AUTO)
+		irq = PARPORT_IRQ_NONE;
+
+	/*
+	 * Release the resource so that parport_pc_probe_port can get it.
+	 */
+	release_resource(base_res);
+	if (parport_pc_probe_port (ite8872_lpt, ite8872_lpthi,
+				   irq, PARPORT_DMA_NONE, NULL)) {
+		printk (KERN_INFO
+			"parport_pc: ITE 8872 parallel port: io=0x%X",
+			ite8872_lpt);
+		if (irq != PARPORT_IRQ_NONE)
+			printk (", irq=%d", irq);
+		printk ("\n");
+		return 1;
+	}
+
+	return 0;
+}
+
+/* VIA 8231 support by Pavel Fedin <sonic_amiga@rambler.ru>
+   based on VIA 686a support code by Jeff Garzik <jgarzik@pobox.com> */
+static int __devinitdata parport_init_mode = 0;
+
+/* Data for two known VIA chips */
+static struct parport_pc_via_data via_686a_data __devinitdata = {
+	0x51,
+	0x50,
+	0x85,
+	0x02,
+	0xE2,
+	0xF0,
+	0xE6
+};
+static struct parport_pc_via_data via_8231_data __devinitdata = {
+	0x45,
+	0x44,
+	0x50,
+	0x04,
+	0xF2,
+	0xFA,
+	0xF6
+};
+
+static int __devinit sio_via_probe (struct pci_dev *pdev, int autoirq,
+					 int autodma, struct parport_pc_via_data *via)
+{
+	u8 tmp, tmp2, siofunc;
+	u8 ppcontrol = 0;
+	int dma, irq;
+	unsigned port1, port2;
+	unsigned have_epp = 0;
+
+	printk(KERN_DEBUG "parport_pc: VIA 686A/8231 detected\n");
+
+	switch(parport_init_mode)
+	{
+	case 1:
+	    printk(KERN_DEBUG "parport_pc: setting SPP mode\n");
+	    siofunc = VIA_FUNCTION_PARPORT_SPP;
+	    break;
+	case 2:
+	    printk(KERN_DEBUG "parport_pc: setting PS/2 mode\n");
+	    siofunc = VIA_FUNCTION_PARPORT_SPP;
+	    ppcontrol = VIA_PARPORT_BIDIR;
+	    break;
+	case 3:
+	    printk(KERN_DEBUG "parport_pc: setting EPP mode\n");
+	    siofunc = VIA_FUNCTION_PARPORT_EPP;
+	    ppcontrol = VIA_PARPORT_BIDIR;
+	    have_epp = 1;
+	    break;
+	case 4:
+	    printk(KERN_DEBUG "parport_pc: setting ECP mode\n");
+	    siofunc = VIA_FUNCTION_PARPORT_ECP;
+	    ppcontrol = VIA_PARPORT_BIDIR;
+	    break;
+	case 5:
+	    printk(KERN_DEBUG "parport_pc: setting EPP+ECP mode\n");
+	    siofunc = VIA_FUNCTION_PARPORT_ECP;
+	    ppcontrol = VIA_PARPORT_BIDIR|VIA_PARPORT_ECPEPP;
+	    have_epp = 1;
+	    break;
+	 default:
+	    printk(KERN_DEBUG "parport_pc: probing current configuration\n");
+	    siofunc = VIA_FUNCTION_PROBE;
+	    break;
+	}
+	/*
+	 * unlock super i/o configuration
+	 */
+	pci_read_config_byte(pdev, via->via_pci_superio_config_reg, &tmp);
+	tmp |= via->via_pci_superio_config_data;
+	pci_write_config_byte(pdev, via->via_pci_superio_config_reg, tmp);
+
+	/* Bits 1-0: Parallel Port Mode / Enable */
+	outb(via->viacfg_function, VIA_CONFIG_INDEX);
+	tmp = inb (VIA_CONFIG_DATA);
+	/* Bit 5: EPP+ECP enable; bit 7: PS/2 bidirectional port enable */
+	outb(via->viacfg_parport_control, VIA_CONFIG_INDEX);
+	tmp2 = inb (VIA_CONFIG_DATA);
+	if (siofunc == VIA_FUNCTION_PROBE)
+	{
+	    siofunc = tmp & VIA_FUNCTION_PARPORT_DISABLE;
+	    ppcontrol = tmp2;
+	}
+	else
+	{
+	    tmp &= ~VIA_FUNCTION_PARPORT_DISABLE;
+	    tmp |= siofunc;
+	    outb(via->viacfg_function, VIA_CONFIG_INDEX);
+	    outb(tmp, VIA_CONFIG_DATA);
+	    tmp2 &= ~(VIA_PARPORT_BIDIR|VIA_PARPORT_ECPEPP);
+	    tmp2 |= ppcontrol;
+	    outb(via->viacfg_parport_control, VIA_CONFIG_INDEX);
+	    outb(tmp2, VIA_CONFIG_DATA);
+	}
+	
+	/* Parallel Port I/O Base Address, bits 9-2 */
+	outb(via->viacfg_parport_base, VIA_CONFIG_INDEX);
+	port1 = inb(VIA_CONFIG_DATA) << 2;
+	
+	printk (KERN_DEBUG "parport_pc: Current parallel port base: 0x%X\n",port1);
+	if ((port1 == 0x3BC) && have_epp)
+	{
+	    outb(via->viacfg_parport_base, VIA_CONFIG_INDEX);
+	    outb((0x378 >> 2), VIA_CONFIG_DATA);
+	    printk(KERN_DEBUG "parport_pc: Parallel port base changed to 0x378\n");
+	    port1 = 0x378;
+	}
+
+	/*
+	 * lock super i/o configuration
+	 */
+	pci_read_config_byte(pdev, via->via_pci_superio_config_reg, &tmp);
+	tmp &= ~via->via_pci_superio_config_data;
+	pci_write_config_byte(pdev, via->via_pci_superio_config_reg, tmp);
+
+	if (siofunc == VIA_FUNCTION_PARPORT_DISABLE) {
+		printk(KERN_INFO "parport_pc: VIA parallel port disabled in BIOS\n");
+		return 0;
+	}
+	
+	/* Bits 7-4: PnP Routing for Parallel Port IRQ */
+	pci_read_config_byte(pdev, via->via_pci_parport_irq_reg, &tmp);
+	irq = ((tmp & VIA_IRQCONTROL_PARALLEL) >> 4);
+
+	if (siofunc == VIA_FUNCTION_PARPORT_ECP)
+	{
+	    /* Bits 3-2: PnP Routing for Parallel Port DMA */
+	    pci_read_config_byte(pdev, via->via_pci_parport_dma_reg, &tmp);
+	    dma = ((tmp & VIA_DMACONTROL_PARALLEL) >> 2);
+	}
+	else
+	    /* if ECP not enabled, DMA is not enabled, assumed bogus 'dma' value */
+	    dma = PARPORT_DMA_NONE;
+
+	/* Let the user (or defaults) steer us away from interrupts and DMA */
+	if (autoirq == PARPORT_IRQ_NONE) {
+	    irq = PARPORT_IRQ_NONE;
+	    dma = PARPORT_DMA_NONE;
+	}
+	if (autodma == PARPORT_DMA_NONE)
+	    dma = PARPORT_DMA_NONE;
+
+	switch (port1) {
+	case 0x3bc: port2 = 0x7bc; break;
+	case 0x378: port2 = 0x778; break;
+	case 0x278: port2 = 0x678; break;
+	default:
+		printk(KERN_INFO "parport_pc: Weird VIA parport base 0x%X, ignoring\n",
+			port1);
+		return 0;
+	}
+
+	/* filter bogus IRQs */
+	switch (irq) {
+	case 0:
+	case 2:
+	case 8:
+	case 13:
+		irq = PARPORT_IRQ_NONE;
+		break;
+
+	default: /* do nothing */
+		break;
+	}
+
+	/* finally, do the probe with values obtained */
+	if (parport_pc_probe_port (port1, port2, irq, dma, NULL)) {
+		printk (KERN_INFO
+			"parport_pc: VIA parallel port: io=0x%X", port1);
+		if (irq != PARPORT_IRQ_NONE)
+			printk (", irq=%d", irq);
+		if (dma != PARPORT_DMA_NONE)
+			printk (", dma=%d", dma);
+		printk ("\n");
+		return 1;
+	}
+	
+	printk(KERN_WARNING "parport_pc: Strange, can't probe VIA parallel port: io=0x%X, irq=%d, dma=%d\n",
+		port1, irq, dma);
+	return 0;
+}
+
+
+enum parport_pc_sio_types {
+	sio_via_686a = 0,	/* Via VT82C686A motherboard Super I/O */
+	sio_via_8231,		/* Via VT8231 south bridge integrated Super IO */
+	sio_ite_8872,
+	last_sio
+};
+
+/* each element directly indexed from enum list, above */
+static struct parport_pc_superio {
+	int (*probe) (struct pci_dev *pdev, int autoirq, int autodma, struct parport_pc_via_data *via);
+	struct parport_pc_via_data *via;
+} parport_pc_superio_info[] __devinitdata = {
+	{ sio_via_probe, &via_686a_data, },
+	{ sio_via_probe, &via_8231_data, },
+	{ sio_ite_8872_probe, NULL, },
+};
+
+enum parport_pc_pci_cards {
+	siig_1p_10x = last_sio,
+	siig_2p_10x,
+	siig_1p_20x,
+	siig_2p_20x,
+	lava_parallel,
+	lava_parallel_dual_a,
+	lava_parallel_dual_b,
+	boca_ioppar,
+	plx_9050,
+	timedia_4078a,
+	timedia_4079h,
+	timedia_4085h,
+	timedia_4088a,
+	timedia_4089a,
+	timedia_4095a,
+	timedia_4096a,
+	timedia_4078u,
+	timedia_4079a,
+	timedia_4085u,
+	timedia_4079r,
+	timedia_4079s,
+	timedia_4079d,
+	timedia_4079e,
+	timedia_4079f,
+	timedia_9079a,
+	timedia_9079b,
+	timedia_9079c,
+	timedia_4006a,
+	timedia_4014,
+	timedia_4008a,
+	timedia_4018,
+	timedia_9018a,
+	syba_2p_epp,
+	syba_1p_ecp,
+	titan_010l,
+	titan_1284p2,
+	avlab_1p,
+	avlab_2p,
+	oxsemi_954,
+	oxsemi_840,
+	aks_0100,
+	mobility_pp,
+	netmos_9705,
+	netmos_9715,
+	netmos_9755,
+	netmos_9805,
+	netmos_9815,
+	netmos_9855,
+};
+
+
+/* each element directly indexed from enum list, above 
+ * (but offset by last_sio) */
+static struct parport_pc_pci {
+	int numports;
+	struct { /* BAR (base address registers) numbers in the config
+                    space header */
+		int lo;
+		int hi; /* -1 if not there, >6 for offset-method (max
+                           BAR is 6) */
+	} addr[4];
+
+	/* If set, this is called immediately after pci_enable_device.
+	 * If it returns non-zero, no probing will take place and the
+	 * ports will not be used. */
+	int (*preinit_hook) (struct pci_dev *pdev, int autoirq, int autodma);
+
+	/* If set, this is called after probing for ports.  If 'failed'
+	 * is non-zero we couldn't use any of the ports. */
+	void (*postinit_hook) (struct pci_dev *pdev, int failed);
+} cards[] __devinitdata = {
+	/* siig_1p_10x */		{ 1, { { 2, 3 }, } },
+	/* siig_2p_10x */		{ 2, { { 2, 3 }, { 4, 5 }, } },
+	/* siig_1p_20x */		{ 1, { { 0, 1 }, } },
+	/* siig_2p_20x */		{ 2, { { 0, 1 }, { 2, 3 }, } },
+	/* lava_parallel */		{ 1, { { 0, -1 }, } },
+	/* lava_parallel_dual_a */	{ 1, { { 0, -1 }, } },
+	/* lava_parallel_dual_b */	{ 1, { { 0, -1 }, } },
+	/* boca_ioppar */		{ 1, { { 0, -1 }, } },
+	/* plx_9050 */			{ 2, { { 4, -1 }, { 5, -1 }, } },
+	/* timedia_4078a */		{ 1, { { 2, -1 }, } },
+	/* timedia_4079h */             { 1, { { 2, 3 }, } },
+	/* timedia_4085h */             { 2, { { 2, -1 }, { 4, -1 }, } },
+	/* timedia_4088a */             { 2, { { 2, 3 }, { 4, 5 }, } },
+	/* timedia_4089a */             { 2, { { 2, 3 }, { 4, 5 }, } },
+	/* timedia_4095a */             { 2, { { 2, 3 }, { 4, 5 }, } },
+	/* timedia_4096a */             { 2, { { 2, 3 }, { 4, 5 }, } },
+	/* timedia_4078u */             { 1, { { 2, -1 }, } },
+	/* timedia_4079a */             { 1, { { 2, 3 }, } },
+	/* timedia_4085u */             { 2, { { 2, -1 }, { 4, -1 }, } },
+	/* timedia_4079r */             { 1, { { 2, 3 }, } },
+	/* timedia_4079s */             { 1, { { 2, 3 }, } },
+	/* timedia_4079d */             { 1, { { 2, 3 }, } },
+	/* timedia_4079e */             { 1, { { 2, 3 }, } },
+	/* timedia_4079f */             { 1, { { 2, 3 }, } },
+	/* timedia_9079a */             { 1, { { 2, 3 }, } },
+	/* timedia_9079b */             { 1, { { 2, 3 }, } },
+	/* timedia_9079c */             { 1, { { 2, 3 }, } },
+	/* timedia_4006a */             { 1, { { 0, -1 }, } },
+	/* timedia_4014  */             { 2, { { 0, -1 }, { 2, -1 }, } },
+	/* timedia_4008a */             { 1, { { 0, 1 }, } },
+	/* timedia_4018  */             { 2, { { 0, 1 }, { 2, 3 }, } },
+	/* timedia_9018a */             { 2, { { 0, 1 }, { 2, 3 }, } },
+					/* SYBA uses fixed offsets in
+                                           a 1K io window */
+	/* syba_2p_epp AP138B */	{ 2, { { 0, 0x078 }, { 0, 0x178 }, } },
+	/* syba_1p_ecp W83787 */	{ 1, { { 0, 0x078 }, } },
+	/* titan_010l */		{ 1, { { 3, -1 }, } },
+	/* titan_1284p2 */		{ 2, { { 0, 1 }, { 2, 3 }, } },
+	/* avlab_1p		*/	{ 1, { { 0, 1}, } },
+	/* avlab_2p		*/	{ 2, { { 0, 1}, { 2, 3 },} },
+	/* The Oxford Semi cards are unusual: 954 doesn't support ECP,
+	 * and 840 locks up if you write 1 to bit 2! */
+	/* oxsemi_954 */		{ 1, { { 0, -1 }, } },
+	/* oxsemi_840 */		{ 1, { { 0, -1 }, } },
+	/* aks_0100 */                  { 1, { { 0, -1 }, } },
+	/* mobility_pp */		{ 1, { { 0, 1 }, } },
+	/* netmos_9705 */               { 1, { { 0, -1 }, } }, /* untested */
+        /* netmos_9715 */               { 2, { { 0, 1 }, { 2, 3 },} }, /* untested */
+        /* netmos_9755 */               { 2, { { 0, 1 }, { 2, 3 },} }, /* untested */
+	/* netmos_9805 */               { 1, { { 0, -1 }, } }, /* untested */
+	/* netmos_9815 */               { 2, { { 0, -1 }, { 2, -1 }, } }, /* untested */
+	/* netmos_9855 */               { 2, { { 0, -1 }, { 2, -1 }, } }, /* untested */
+};
+
+static struct pci_device_id parport_pc_pci_tbl[] = {
+	/* Super-IO onboard chips */
+	{ 0x1106, 0x0686, PCI_ANY_ID, PCI_ANY_ID, 0, 0, sio_via_686a },
+	{ 0x1106, 0x8231, PCI_ANY_ID, PCI_ANY_ID, 0, 0, sio_via_8231 },
+	{ PCI_VENDOR_ID_ITE, PCI_DEVICE_ID_ITE_8872,
+	  PCI_ANY_ID, PCI_ANY_ID, 0, 0, sio_ite_8872 },
+
+	/* PCI cards */
+	{ PCI_VENDOR_ID_SIIG, PCI_DEVICE_ID_SIIG_1P_10x,
+	  PCI_ANY_ID, PCI_ANY_ID, 0, 0, siig_1p_10x },
+	{ PCI_VENDOR_ID_SIIG, PCI_DEVICE_ID_SIIG_2P_10x,
+	  PCI_ANY_ID, PCI_ANY_ID, 0, 0, siig_2p_10x },
+	{ PCI_VENDOR_ID_SIIG, PCI_DEVICE_ID_SIIG_1P_20x,
+	  PCI_ANY_ID, PCI_ANY_ID, 0, 0, siig_1p_20x },
+	{ PCI_VENDOR_ID_SIIG, PCI_DEVICE_ID_SIIG_2P_20x,
+	  PCI_ANY_ID, PCI_ANY_ID, 0, 0, siig_2p_20x },
+	{ PCI_VENDOR_ID_LAVA, PCI_DEVICE_ID_LAVA_PARALLEL,
+	  PCI_ANY_ID, PCI_ANY_ID, 0, 0, lava_parallel },
+	{ PCI_VENDOR_ID_LAVA, PCI_DEVICE_ID_LAVA_DUAL_PAR_A,
+	  PCI_ANY_ID, PCI_ANY_ID, 0, 0, lava_parallel_dual_a },
+	{ PCI_VENDOR_ID_LAVA, PCI_DEVICE_ID_LAVA_DUAL_PAR_B,
+	  PCI_ANY_ID, PCI_ANY_ID, 0, 0, lava_parallel_dual_b },
+	{ PCI_VENDOR_ID_LAVA, PCI_DEVICE_ID_LAVA_BOCA_IOPPAR,
+	  PCI_ANY_ID, PCI_ANY_ID, 0, 0, boca_ioppar },
+	{ PCI_VENDOR_ID_PLX, PCI_DEVICE_ID_PLX_9050,
+	  PCI_SUBVENDOR_ID_EXSYS, PCI_SUBDEVICE_ID_EXSYS_4014, 0,0, plx_9050 },
+	/* PCI_VENDOR_ID_TIMEDIA/SUNIX has many differing cards ...*/
+	{ 0x1409, 0x7168, 0x1409, 0x4078, 0, 0, timedia_4078a },
+	{ 0x1409, 0x7168, 0x1409, 0x4079, 0, 0, timedia_4079h },
+	{ 0x1409, 0x7168, 0x1409, 0x4085, 0, 0, timedia_4085h },
+	{ 0x1409, 0x7168, 0x1409, 0x4088, 0, 0, timedia_4088a },
+	{ 0x1409, 0x7168, 0x1409, 0x4089, 0, 0, timedia_4089a },
+	{ 0x1409, 0x7168, 0x1409, 0x4095, 0, 0, timedia_4095a },
+	{ 0x1409, 0x7168, 0x1409, 0x4096, 0, 0, timedia_4096a },
+	{ 0x1409, 0x7168, 0x1409, 0x5078, 0, 0, timedia_4078u },
+	{ 0x1409, 0x7168, 0x1409, 0x5079, 0, 0, timedia_4079a },
+	{ 0x1409, 0x7168, 0x1409, 0x5085, 0, 0, timedia_4085u },
+	{ 0x1409, 0x7168, 0x1409, 0x6079, 0, 0, timedia_4079r },
+	{ 0x1409, 0x7168, 0x1409, 0x7079, 0, 0, timedia_4079s },
+	{ 0x1409, 0x7168, 0x1409, 0x8079, 0, 0, timedia_4079d },
+	{ 0x1409, 0x7168, 0x1409, 0x9079, 0, 0, timedia_4079e },
+	{ 0x1409, 0x7168, 0x1409, 0xa079, 0, 0, timedia_4079f },
+	{ 0x1409, 0x7168, 0x1409, 0xb079, 0, 0, timedia_9079a },
+	{ 0x1409, 0x7168, 0x1409, 0xc079, 0, 0, timedia_9079b },
+	{ 0x1409, 0x7168, 0x1409, 0xd079, 0, 0, timedia_9079c },
+	{ 0x1409, 0x7268, 0x1409, 0x0101, 0, 0, timedia_4006a },
+	{ 0x1409, 0x7268, 0x1409, 0x0102, 0, 0, timedia_4014 },
+	{ 0x1409, 0x7268, 0x1409, 0x0103, 0, 0, timedia_4008a },
+	{ 0x1409, 0x7268, 0x1409, 0x0104, 0, 0, timedia_4018 },
+	{ 0x1409, 0x7268, 0x1409, 0x9018, 0, 0, timedia_9018a },
+	{ 0x14f2, 0x0121, PCI_ANY_ID, PCI_ANY_ID, 0, 0, mobility_pp },
+	{ PCI_VENDOR_ID_SYBA, PCI_DEVICE_ID_SYBA_2P_EPP,
+	  PCI_ANY_ID, PCI_ANY_ID, 0, 0, syba_2p_epp },
+	{ PCI_VENDOR_ID_SYBA, PCI_DEVICE_ID_SYBA_1P_ECP,
+	  PCI_ANY_ID, PCI_ANY_ID, 0, 0, syba_1p_ecp },
+	{ PCI_VENDOR_ID_TITAN, PCI_DEVICE_ID_TITAN_010L,
+	  PCI_ANY_ID, PCI_ANY_ID, 0, 0, titan_010l },
+	{ 0x9710, 0x9815, 0x1000, 0x0020, 0, 0, titan_1284p2 },
+	/* PCI_VENDOR_ID_AVLAB/Intek21 has another bunch of cards ...*/
+	{ 0x14db, 0x2120, PCI_ANY_ID, PCI_ANY_ID, 0, 0, avlab_1p}, /* AFAVLAB_TK9902 */
+	{ 0x14db, 0x2121, PCI_ANY_ID, PCI_ANY_ID, 0, 0, avlab_2p},
+	{ PCI_VENDOR_ID_OXSEMI, PCI_DEVICE_ID_OXSEMI_16PCI954PP,
+	  PCI_ANY_ID, PCI_ANY_ID, 0, 0, oxsemi_954 },
+	{ PCI_VENDOR_ID_OXSEMI, PCI_DEVICE_ID_OXSEMI_12PCI840,
+	  PCI_ANY_ID, PCI_ANY_ID, 0, 0, oxsemi_840 },
+	{ PCI_VENDOR_ID_AKS, PCI_DEVICE_ID_AKS_ALADDINCARD,
+	  PCI_ANY_ID, PCI_ANY_ID, 0, 0, aks_0100 },
+	/* NetMos communication controllers */
+	{ PCI_VENDOR_ID_NETMOS, PCI_DEVICE_ID_NETMOS_9705,
+	  PCI_ANY_ID, PCI_ANY_ID, 0, 0, netmos_9705 },
+	{ PCI_VENDOR_ID_NETMOS, PCI_DEVICE_ID_NETMOS_9715,
+	  PCI_ANY_ID, PCI_ANY_ID, 0, 0, netmos_9715 },
+	{ PCI_VENDOR_ID_NETMOS, PCI_DEVICE_ID_NETMOS_9755,
+	  PCI_ANY_ID, PCI_ANY_ID, 0, 0, netmos_9755 },
+	{ PCI_VENDOR_ID_NETMOS, PCI_DEVICE_ID_NETMOS_9805,
+	  PCI_ANY_ID, PCI_ANY_ID, 0, 0, netmos_9805 },
+	{ PCI_VENDOR_ID_NETMOS, PCI_DEVICE_ID_NETMOS_9815,
+	  PCI_ANY_ID, PCI_ANY_ID, 0, 0, netmos_9815 },
+	{ PCI_VENDOR_ID_NETMOS, PCI_DEVICE_ID_NETMOS_9855,
+	  PCI_ANY_ID, PCI_ANY_ID, 0, 0, netmos_9855 },
+	{ 0, } /* terminate list */
+};
+MODULE_DEVICE_TABLE(pci,parport_pc_pci_tbl);
+
+struct pci_parport_data {
+	int num;
+	struct parport *ports[2];
+};
+
+static int parport_pc_pci_probe (struct pci_dev *dev,
+					   const struct pci_device_id *id)
+{
+	int err, count, n, i = id->driver_data;
+	struct pci_parport_data *data;
+
+	if (i < last_sio)
+		/* This is an onboard Super-IO and has already been probed */
+		return 0;
+
+	/* This is a PCI card */
+	i -= last_sio;
+	count = 0;
+	if ((err = pci_enable_device (dev)) != 0)
+		return err;
+
+	data = kmalloc(sizeof(struct pci_parport_data), GFP_KERNEL);
+	if (!data)
+		return -ENOMEM;
+
+	if (cards[i].preinit_hook &&
+	    cards[i].preinit_hook (dev, PARPORT_IRQ_NONE, PARPORT_DMA_NONE)) {
+		kfree(data);
+		return -ENODEV;
+	}
+
+	for (n = 0; n < cards[i].numports; n++) {
+		int lo = cards[i].addr[n].lo;
+		int hi = cards[i].addr[n].hi;
+		unsigned long io_lo, io_hi;
+		io_lo = pci_resource_start (dev, lo);
+		io_hi = 0;
+		if ((hi >= 0) && (hi <= 6))
+			io_hi = pci_resource_start (dev, hi);
+		else if (hi > 6)
+			io_lo += hi; /* Reinterpret the meaning of
+                                        "hi" as an offset (see SYBA
+                                        def.) */
+		/* TODO: test if sharing interrupts works */
+		printk (KERN_DEBUG "PCI parallel port detected: %04x:%04x, "
+			"I/O at %#lx(%#lx)\n",
+			parport_pc_pci_tbl[i + last_sio].vendor,
+			parport_pc_pci_tbl[i + last_sio].device, io_lo, io_hi);
+		data->ports[count] =
+			parport_pc_probe_port (io_lo, io_hi, PARPORT_IRQ_NONE,
+					       PARPORT_DMA_NONE, dev);
+		if (data->ports[count])
+			count++;
+	}
+
+	data->num = count;
+
+	if (cards[i].postinit_hook)
+		cards[i].postinit_hook (dev, count == 0);
+
+	if (count) {
+		pci_set_drvdata(dev, data);
+		return 0;
+	}
+
+	kfree(data);
+
+	return -ENODEV;
+}
+
+static void __devexit parport_pc_pci_remove(struct pci_dev *dev)
+{
+	struct pci_parport_data *data = pci_get_drvdata(dev);
+	int i;
+
+	pci_set_drvdata(dev, NULL);
+
+	if (data) {
+		for (i = data->num - 1; i >= 0; i--)
+			parport_pc_unregister_port(data->ports[i]);
+
+		kfree(data);
+	}
+}
+
+static struct pci_driver parport_pc_pci_driver = {
+	.name		= "parport_pc",
+	.id_table	= parport_pc_pci_tbl,
+	.probe		= parport_pc_pci_probe,
+	.remove		= __devexit_p(parport_pc_pci_remove),
+};
+
+static int __init parport_pc_init_superio (int autoirq, int autodma)
+{
+	const struct pci_device_id *id;
+	struct pci_dev *pdev = NULL;
+	int ret = 0;
+
+	while ((pdev = pci_find_device(PCI_ANY_ID, PCI_ANY_ID, pdev)) != NULL) {
+		id = pci_match_device (parport_pc_pci_tbl, pdev);
+		if (id == NULL || id->driver_data >= last_sio)
+			continue;
+
+		if (parport_pc_superio_info[id->driver_data].probe
+			(pdev, autoirq, autodma,parport_pc_superio_info[id->driver_data].via)) {
+			ret++;
+		}
+	}
+
+	return ret; /* number of devices found */
+}
+#else
+static struct pci_driver parport_pc_pci_driver;
+static int __init parport_pc_init_superio(int autoirq, int autodma) {return 0;}
+#endif /* CONFIG_PCI */
+
+
+static const struct pnp_device_id parport_pc_pnp_tbl[] = {
+	/* Standard LPT Printer Port */
+	{.id = "PNP0400", .driver_data = 0},
+	/* ECP Printer Port */
+	{.id = "PNP0401", .driver_data = 0},
+	{ }
+};
+
+MODULE_DEVICE_TABLE(pnp,parport_pc_pnp_tbl);
+
+static int parport_pc_pnp_probe(struct pnp_dev *dev, const struct pnp_device_id *id)
+{
+	struct parport *pdata;
+	unsigned long io_lo, io_hi;
+	int dma, irq;
+
+	if (pnp_port_valid(dev,0) &&
+		!(pnp_port_flags(dev,0) & IORESOURCE_DISABLED)) {
+		io_lo = pnp_port_start(dev,0);
+	} else
+		return -EINVAL;
+
+	if (pnp_port_valid(dev,1) &&
+		!(pnp_port_flags(dev,1) & IORESOURCE_DISABLED)) {
+		io_hi = pnp_port_start(dev,1);
+	} else
+		io_hi = 0;
+
+	if (pnp_irq_valid(dev,0) &&
+		!(pnp_irq_flags(dev,0) & IORESOURCE_DISABLED)) {
+		irq = pnp_irq(dev,0);
+	} else
+		irq = PARPORT_IRQ_NONE;
+
+	if (pnp_dma_valid(dev,0) &&
+		!(pnp_dma_flags(dev,0) & IORESOURCE_DISABLED)) {
+		dma = pnp_dma(dev,0);
+	} else
+		dma = PARPORT_DMA_NONE;
+
+	printk(KERN_INFO "parport: PnPBIOS parport detected.\n");
+	if (!(pdata = parport_pc_probe_port (io_lo, io_hi, irq, dma, NULL)))
+		return -ENODEV;
+
+	pnp_set_drvdata(dev,pdata);
+	return 0;
+}
+
+static void parport_pc_pnp_remove(struct pnp_dev *dev)
+{
+	struct parport *pdata = (struct parport *)pnp_get_drvdata(dev);
+	if (!pdata)
+		return;
+
+	parport_pc_unregister_port(pdata);
+}
+
+/* we only need the pnp layer to activate the device, at least for now */
+static struct pnp_driver parport_pc_pnp_driver = {
+	.name		= "parport_pc",
+	.id_table	= parport_pc_pnp_tbl,
+	.probe		= parport_pc_pnp_probe,
+	.remove		= parport_pc_pnp_remove,
+};
+
+
+/* This is called by parport_pc_find_nonpci_ports (in asm/parport.h) */
+static int __devinit __attribute__((unused))
+parport_pc_find_isa_ports (int autoirq, int autodma)
+{
+	int count = 0;
+
+	if (parport_pc_probe_port(0x3bc, 0x7bc, autoirq, autodma, NULL))
+		count++;
+	if (parport_pc_probe_port(0x378, 0x778, autoirq, autodma, NULL))
+		count++;
+	if (parport_pc_probe_port(0x278, 0x678, autoirq, autodma, NULL))
+		count++;
+
+	return count;
+}
+
+/* This function is called by parport_pc_init if the user didn't
+ * specify any ports to probe.  Its job is to find some ports.  Order
+ * is important here -- we want ISA ports to be registered first,
+ * followed by PCI cards (for least surprise), but before that we want
+ * to do chipset-specific tests for some onboard ports that we know
+ * about.
+ *
+ * autoirq is PARPORT_IRQ_NONE, PARPORT_IRQ_AUTO, or PARPORT_IRQ_PROBEONLY
+ * autodma is PARPORT_DMA_NONE or PARPORT_DMA_AUTO
+ */
+static int __init parport_pc_find_ports (int autoirq, int autodma)
+{
+	int count = 0, r;
+
+#ifdef CONFIG_PARPORT_PC_SUPERIO
+	detect_and_report_winbond ();
+	detect_and_report_smsc ();
+#endif
+
+	/* Onboard SuperIO chipsets that show themselves on the PCI bus. */
+	count += parport_pc_init_superio (autoirq, autodma);
+
+	/* PnP ports, skip detection if SuperIO already found them */
+	if (!count) {
+		r = pnp_register_driver (&parport_pc_pnp_driver);
+		if (r >= 0) {
+			pnp_registered_parport = 1;
+			count += r;
+		}
+	}
+
+	/* ISA ports and whatever (see asm/parport.h). */
+	count += parport_pc_find_nonpci_ports (autoirq, autodma);
+
+	r = pci_register_driver (&parport_pc_pci_driver);
+	if (r)
+		return r;
+	pci_registered_parport = 1;
+	count += 1;
+
+	return count;
+}
+
+/*
+ *	Piles of crap below pretend to be a parser for module and kernel
+ *	parameters.  Say "thank you" to whoever had come up with that
+ *	syntax and keep in mind that code below is a cleaned up version.
+ */
+
+static int __initdata io[PARPORT_PC_MAX_PORTS+1] = { [0 ... PARPORT_PC_MAX_PORTS] = 0 };
+static int __initdata io_hi[PARPORT_PC_MAX_PORTS+1] =
+	{ [0 ... PARPORT_PC_MAX_PORTS] = PARPORT_IOHI_AUTO };
+static int __initdata dmaval[PARPORT_PC_MAX_PORTS] = { [0 ... PARPORT_PC_MAX_PORTS-1] = PARPORT_DMA_NONE };
+static int __initdata irqval[PARPORT_PC_MAX_PORTS] = { [0 ... PARPORT_PC_MAX_PORTS-1] = PARPORT_IRQ_PROBEONLY };
+
+static int __init parport_parse_param(const char *s, int *val,
+				int automatic, int none, int nofifo)
+{
+	if (!s)
+		return 0;
+	if (!strncmp(s, "auto", 4))
+		*val = automatic;
+	else if (!strncmp(s, "none", 4))
+		*val = none;
+	else if (nofifo && !strncmp(s, "nofifo", 4))
+		*val = nofifo;
+	else {
+		char *ep;
+		unsigned long r = simple_strtoul(s, &ep, 0);
+		if (ep != s)
+			*val = r;
+		else {
+			printk(KERN_ERR "parport: bad specifier `%s'\n", s);
+			return -1;
+		}
+	}
+	return 0;
+}
+
+static int __init parport_parse_irq(const char *irqstr, int *val)
+{
+	return parport_parse_param(irqstr, val, PARPORT_IRQ_AUTO,
+				     PARPORT_IRQ_NONE, 0);
+}
+
+static int __init parport_parse_dma(const char *dmastr, int *val)
+{
+	return parport_parse_param(dmastr, val, PARPORT_DMA_AUTO,
+				     PARPORT_DMA_NONE, PARPORT_DMA_NOFIFO);
+}
+
+#ifdef CONFIG_PCI
+static int __init parport_init_mode_setup(char *str)
+{
+	printk(KERN_DEBUG "parport_pc.c: Specified parameter parport_init_mode=%s\n", str);
+
+	if (!strcmp (str, "spp"))
+		parport_init_mode=1;
+	if (!strcmp (str, "ps2"))
+		parport_init_mode=2;
+	if (!strcmp (str, "epp"))
+		parport_init_mode=3;
+	if (!strcmp (str, "ecp"))
+		parport_init_mode=4;
+	if (!strcmp (str, "ecpepp"))
+		parport_init_mode=5;
+	return 1;
+}
+#endif
+
+#ifdef MODULE
+static const char *irq[PARPORT_PC_MAX_PORTS];
+static const char *dma[PARPORT_PC_MAX_PORTS];
+
+MODULE_PARM_DESC(io, "Base I/O address (SPP regs)");
+module_param_array(io, int, NULL, 0);
+MODULE_PARM_DESC(io_hi, "Base I/O address (ECR)");
+module_param_array(io_hi, int, NULL, 0);
+MODULE_PARM_DESC(irq, "IRQ line");
+module_param_array(irq, charp, NULL, 0);
+MODULE_PARM_DESC(dma, "DMA channel");
+module_param_array(dma, charp, NULL, 0);
+#if defined(CONFIG_PARPORT_PC_SUPERIO) || \
+       (defined(CONFIG_PARPORT_1284) && defined(CONFIG_PARPORT_PC_FIFO))
+MODULE_PARM_DESC(verbose_probing, "Log chit-chat during initialisation");
+module_param(verbose_probing, int, 0644);
+#endif
+#ifdef CONFIG_PCI
+static char *init_mode;
+MODULE_PARM_DESC(init_mode, "Initialise mode for VIA VT8231 port (spp, ps2, epp, ecp or ecpepp)");
+module_param(init_mode, charp, 0);
+#endif
+
+static int __init parse_parport_params(void)
+{
+	unsigned int i;
+	int val;
+
+#ifdef CONFIG_PCI
+	if (init_mode)
+		parport_init_mode_setup(init_mode);
+#endif
+
+	for (i = 0; i < PARPORT_PC_MAX_PORTS && io[i]; i++) {
+		if (parport_parse_irq(irq[i], &val))
+			return 1;
+		irqval[i] = val;
+		if (parport_parse_dma(dma[i], &val))
+			return 1;
+		dmaval[i] = val;
+	}
+	if (!io[0]) {
+		/* The user can make us use any IRQs or DMAs we find. */
+		if (irq[0] && !parport_parse_irq(irq[0], &val))
+			switch (val) {
+			case PARPORT_IRQ_NONE:
+			case PARPORT_IRQ_AUTO:
+				irqval[0] = val;
+				break;
+			default:
+				printk (KERN_WARNING
+					"parport_pc: irq specified "
+					"without base address.  Use 'io=' "
+					"to specify one\n");
+			}
+
+		if (dma[0] && !parport_parse_dma(dma[0], &val))
+			switch (val) {
+			case PARPORT_DMA_NONE:
+			case PARPORT_DMA_AUTO:
+				dmaval[0] = val;
+				break;
+			default:
+				printk (KERN_WARNING
+					"parport_pc: dma specified "
+					"without base address.  Use 'io=' "
+					"to specify one\n");
+			}
+	}
+	return 0;
+}
+
+#else
+
+static int parport_setup_ptr __initdata = 0;
+
+/*
+ * Acceptable parameters:
+ *
+ * parport=0
+ * parport=auto
+ * parport=0xBASE[,IRQ[,DMA]]
+ *
+ * IRQ/DMA may be numeric or 'auto' or 'none'
+ */
+static int __init parport_setup (char *str)
+{
+	char *endptr;
+	char *sep;
+	int val;
+
+	if (!str || !*str || (*str == '0' && !*(str+1))) {
+		/* Disable parport if "parport=0" in cmdline */
+		io[0] = PARPORT_DISABLE;
+		return 1;
+	}
+
+	if (!strncmp (str, "auto", 4)) {
+		irqval[0] = PARPORT_IRQ_AUTO;
+		dmaval[0] = PARPORT_DMA_AUTO;
+		return 1;
+	}
+
+	val = simple_strtoul (str, &endptr, 0);
+	if (endptr == str) {
+		printk (KERN_WARNING "parport=%s not understood\n", str);
+		return 1;
+	}
+
+	if (parport_setup_ptr == PARPORT_PC_MAX_PORTS) {
+		printk(KERN_ERR "parport=%s ignored, too many ports\n", str);
+		return 1;
+	}
+
+	io[parport_setup_ptr] = val;
+	irqval[parport_setup_ptr] = PARPORT_IRQ_NONE;
+	dmaval[parport_setup_ptr] = PARPORT_DMA_NONE;
+
+	sep = strchr(str, ',');
+	if (sep++) {
+		if (parport_parse_irq(sep, &val))
+			return 1;
+		irqval[parport_setup_ptr] = val;
+		sep = strchr(sep, ',');
+		if (sep++) {
+			if (parport_parse_dma(sep, &val))
+				return 1;
+			dmaval[parport_setup_ptr] = val;
+		}
+	}
+	parport_setup_ptr++;
+	return 1;
+}
+
+static int __init parse_parport_params(void)
+{
+	return io[0] == PARPORT_DISABLE;
+}
+
+__setup ("parport=", parport_setup);
+
+/*
+ * Acceptable parameters:
+ *
+ * parport_init_mode=[spp|ps2|epp|ecp|ecpepp]
+ */
+#ifdef CONFIG_PCI
+__setup("parport_init_mode=",parport_init_mode_setup);
+#endif
+#endif
+
+/* "Parser" ends here */
+
+static int __init parport_pc_init(void)
+{
+	int count = 0;
+
+	if (parse_parport_params())
+		return -EINVAL;
+
+	if (io[0]) {
+		int i;
+		/* Only probe the ports we were given. */
+		user_specified = 1;
+		for (i = 0; i < PARPORT_PC_MAX_PORTS; i++) {
+			if (!io[i])
+				break;
+			if ((io_hi[i]) == PARPORT_IOHI_AUTO)
+			       io_hi[i] = 0x400 + io[i];
+			if (parport_pc_probe_port(io[i], io_hi[i],
+						  irqval[i], dmaval[i], NULL))
+				count++;
+		}
+	} else
+		count += parport_pc_find_ports (irqval[0], dmaval[0]);
+
+	return 0;
+}
+
+static void __exit parport_pc_exit(void)
+{
+	if (pci_registered_parport)
+		pci_unregister_driver (&parport_pc_pci_driver);
+	if (pnp_registered_parport)
+		pnp_unregister_driver (&parport_pc_pnp_driver);
+
+	spin_lock(&ports_lock);
+	while (!list_empty(&ports_list)) {
+		struct parport_pc_private *priv;
+		struct parport *port;
+		priv = list_entry(ports_list.next,
+				  struct parport_pc_private, list);
+		port = priv->port;
+		spin_unlock(&ports_lock);
+		parport_pc_unregister_port(port);
+		spin_lock(&ports_lock);
+	}
+	spin_unlock(&ports_lock);
+}
+
+MODULE_AUTHOR("Phil Blundell, Tim Waugh, others");
+MODULE_DESCRIPTION("PC-style parallel port driver");
+MODULE_LICENSE("GPL");
+module_init(parport_pc_init)
+module_exit(parport_pc_exit)