USB: add Freescale high-speed USB SOC device controller driver

Freescale high-speed USB SOC can be found on some Freescale processors
among different architectures.  It supports both host and device functions.
This driver adds its device support for Linux USB Gadget layer.
It is tested on MPC8349 and MPC8313, but should work on other platforms
with minor tweaks.  The driver passed USBCV 1.3 compliance tests.  Note
that this driver doesn't yet include OTG support.

Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Jiang Bo <tanya.jiang@freescale.com>
Signed-off-by: Bruce Schmid <duck@freescale.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

1 files changed, 579 insertions, 0 deletions

diff --git a/drivers/usb/gadget/fsl_usb2_udc.h b/drivers/usb/gadget/fsl_usb2_udc.h
new file mode 100644
index 0000000..c6291e0
--- /dev/null
+++ b/drivers/usb/gadget/fsl_usb2_udc.h
@@ -0,0 +1,579 @@
+/*
+ * Freescale USB device/endpoint management registers
+ */
+#ifndef __FSL_USB2_UDC_H
+#define __FSL_USB2_UDC_H
+
+/* ### define USB registers here
+ */
+#define USB_MAX_CTRL_PAYLOAD		64
+#define USB_DR_SYS_OFFSET		0x400
+
+ /* USB DR device mode registers (Little Endian) */
+struct usb_dr_device {
+	/* Capability register */
+	u8 res1[256];
+	u16 caplength;		/* Capability Register Length */
+	u16 hciversion;		/* Host Controller Interface Version */
+	u32 hcsparams;		/* Host Controller Structual Parameters */
+	u32 hccparams;		/* Host Controller Capability Parameters */
+	u8 res2[20];
+	u32 dciversion;		/* Device Controller Interface Version */
+	u32 dccparams;		/* Device Controller Capability Parameters */
+	u8 res3[24];
+	/* Operation register */
+	u32 usbcmd;		/* USB Command Register */
+	u32 usbsts;		/* USB Status Register */
+	u32 usbintr;		/* USB Interrupt Enable Register */
+	u32 frindex;		/* Frame Index Register */
+	u8 res4[4];
+	u32 deviceaddr;		/* Device Address */
+	u32 endpointlistaddr;	/* Endpoint List Address Register */
+	u8 res5[4];
+	u32 burstsize;		/* Master Interface Data Burst Size Register */
+	u32 txttfilltuning;	/* Transmit FIFO Tuning Controls Register */
+	u8 res6[24];
+	u32 configflag;		/* Configure Flag Register */
+	u32 portsc1;		/* Port 1 Status and Control Register */
+	u8 res7[28];
+	u32 otgsc;		/* On-The-Go Status and Control */
+	u32 usbmode;		/* USB Mode Register */
+	u32 endptsetupstat;	/* Endpoint Setup Status Register */
+	u32 endpointprime;	/* Endpoint Initialization Register */
+	u32 endptflush;		/* Endpoint Flush Register */
+	u32 endptstatus;	/* Endpoint Status Register */
+	u32 endptcomplete;	/* Endpoint Complete Register */
+	u32 endptctrl[6];	/* Endpoint Control Registers */
+};
+
+ /* USB DR host mode registers (Little Endian) */
+struct usb_dr_host {
+	/* Capability register */
+	u8 res1[256];
+	u16 caplength;		/* Capability Register Length */
+	u16 hciversion;		/* Host Controller Interface Version */
+	u32 hcsparams;		/* Host Controller Structual Parameters */
+	u32 hccparams;		/* Host Controller Capability Parameters */
+	u8 res2[20];
+	u32 dciversion;		/* Device Controller Interface Version */
+	u32 dccparams;		/* Device Controller Capability Parameters */
+	u8 res3[24];
+	/* Operation register */
+	u32 usbcmd;		/* USB Command Register */
+	u32 usbsts;		/* USB Status Register */
+	u32 usbintr;		/* USB Interrupt Enable Register */
+	u32 frindex;		/* Frame Index Register */
+	u8 res4[4];
+	u32 periodiclistbase;	/* Periodic Frame List Base Address Register */
+	u32 asynclistaddr;	/* Current Asynchronous List Address Register */
+	u8 res5[4];
+	u32 burstsize;		/* Master Interface Data Burst Size Register */
+	u32 txttfilltuning;	/* Transmit FIFO Tuning Controls Register */
+	u8 res6[24];
+	u32 configflag;		/* Configure Flag Register */
+	u32 portsc1;		/* Port 1 Status and Control Register */
+	u8 res7[28];
+	u32 otgsc;		/* On-The-Go Status and Control */
+	u32 usbmode;		/* USB Mode Register */
+	u32 endptsetupstat;	/* Endpoint Setup Status Register */
+	u32 endpointprime;	/* Endpoint Initialization Register */
+	u32 endptflush;		/* Endpoint Flush Register */
+	u32 endptstatus;	/* Endpoint Status Register */
+	u32 endptcomplete;	/* Endpoint Complete Register */
+	u32 endptctrl[6];	/* Endpoint Control Registers */
+};
+
+ /* non-EHCI USB system interface registers (Big Endian) */
+struct usb_sys_interface {
+	u32 snoop1;
+	u32 snoop2;
+	u32 age_cnt_thresh;	/* Age Count Threshold Register */
+	u32 pri_ctrl;		/* Priority Control Register */
+	u32 si_ctrl;		/* System Interface Control Register */
+	u8 res[236];
+	u32 control;		/* General Purpose Control Register */
+};
+
+/* ep0 transfer state */
+#define WAIT_FOR_SETUP          0
+#define DATA_STATE_XMIT         1
+#define DATA_STATE_NEED_ZLP     2
+#define WAIT_FOR_OUT_STATUS     3
+#define DATA_STATE_RECV         4
+
+/* Frame Index Register Bit Masks */
+#define	USB_FRINDEX_MASKS			0x3fff
+/* USB CMD  Register Bit Masks */
+#define  USB_CMD_RUN_STOP                     0x00000001
+#define  USB_CMD_CTRL_RESET                   0x00000002
+#define  USB_CMD_PERIODIC_SCHEDULE_EN         0x00000010
+#define  USB_CMD_ASYNC_SCHEDULE_EN            0x00000020
+#define  USB_CMD_INT_AA_DOORBELL              0x00000040
+#define  USB_CMD_ASP                          0x00000300
+#define  USB_CMD_ASYNC_SCH_PARK_EN            0x00000800
+#define  USB_CMD_SUTW                         0x00002000
+#define  USB_CMD_ATDTW                        0x00004000
+#define  USB_CMD_ITC                          0x00FF0000
+
+/* bit 15,3,2 are frame list size */
+#define  USB_CMD_FRAME_SIZE_1024              0x00000000
+#define  USB_CMD_FRAME_SIZE_512               0x00000004
+#define  USB_CMD_FRAME_SIZE_256               0x00000008
+#define  USB_CMD_FRAME_SIZE_128               0x0000000C
+#define  USB_CMD_FRAME_SIZE_64                0x00008000
+#define  USB_CMD_FRAME_SIZE_32                0x00008004
+#define  USB_CMD_FRAME_SIZE_16                0x00008008
+#define  USB_CMD_FRAME_SIZE_8                 0x0000800C
+
+/* bit 9-8 are async schedule park mode count */
+#define  USB_CMD_ASP_00                       0x00000000
+#define  USB_CMD_ASP_01                       0x00000100
+#define  USB_CMD_ASP_10                       0x00000200
+#define  USB_CMD_ASP_11                       0x00000300
+#define  USB_CMD_ASP_BIT_POS                  8
+
+/* bit 23-16 are interrupt threshold control */
+#define  USB_CMD_ITC_NO_THRESHOLD             0x00000000
+#define  USB_CMD_ITC_1_MICRO_FRM              0x00010000
+#define  USB_CMD_ITC_2_MICRO_FRM              0x00020000
+#define  USB_CMD_ITC_4_MICRO_FRM              0x00040000
+#define  USB_CMD_ITC_8_MICRO_FRM              0x00080000
+#define  USB_CMD_ITC_16_MICRO_FRM             0x00100000
+#define  USB_CMD_ITC_32_MICRO_FRM             0x00200000
+#define  USB_CMD_ITC_64_MICRO_FRM             0x00400000
+#define  USB_CMD_ITC_BIT_POS                  16
+
+/* USB STS Register Bit Masks */
+#define  USB_STS_INT                          0x00000001
+#define  USB_STS_ERR                          0x00000002
+#define  USB_STS_PORT_CHANGE                  0x00000004
+#define  USB_STS_FRM_LST_ROLL                 0x00000008
+#define  USB_STS_SYS_ERR                      0x00000010
+#define  USB_STS_IAA                          0x00000020
+#define  USB_STS_RESET                        0x00000040
+#define  USB_STS_SOF                          0x00000080
+#define  USB_STS_SUSPEND                      0x00000100
+#define  USB_STS_HC_HALTED                    0x00001000
+#define  USB_STS_RCL                          0x00002000
+#define  USB_STS_PERIODIC_SCHEDULE            0x00004000
+#define  USB_STS_ASYNC_SCHEDULE               0x00008000
+
+/* USB INTR Register Bit Masks */
+#define  USB_INTR_INT_EN                      0x00000001
+#define  USB_INTR_ERR_INT_EN                  0x00000002
+#define  USB_INTR_PTC_DETECT_EN               0x00000004
+#define  USB_INTR_FRM_LST_ROLL_EN             0x00000008
+#define  USB_INTR_SYS_ERR_EN                  0x00000010
+#define  USB_INTR_ASYN_ADV_EN                 0x00000020
+#define  USB_INTR_RESET_EN                    0x00000040
+#define  USB_INTR_SOF_EN                      0x00000080
+#define  USB_INTR_DEVICE_SUSPEND              0x00000100
+
+/* Device Address bit masks */
+#define  USB_DEVICE_ADDRESS_MASK              0xFE000000
+#define  USB_DEVICE_ADDRESS_BIT_POS           25
+
+/* endpoint list address bit masks */
+#define USB_EP_LIST_ADDRESS_MASK              0xfffff800
+
+/* PORTSCX  Register Bit Masks */
+#define  PORTSCX_CURRENT_CONNECT_STATUS       0x00000001
+#define  PORTSCX_CONNECT_STATUS_CHANGE        0x00000002
+#define  PORTSCX_PORT_ENABLE                  0x00000004
+#define  PORTSCX_PORT_EN_DIS_CHANGE           0x00000008
+#define  PORTSCX_OVER_CURRENT_ACT             0x00000010
+#define  PORTSCX_OVER_CURRENT_CHG             0x00000020
+#define  PORTSCX_PORT_FORCE_RESUME            0x00000040
+#define  PORTSCX_PORT_SUSPEND                 0x00000080
+#define  PORTSCX_PORT_RESET                   0x00000100
+#define  PORTSCX_LINE_STATUS_BITS             0x00000C00
+#define  PORTSCX_PORT_POWER                   0x00001000
+#define  PORTSCX_PORT_INDICTOR_CTRL           0x0000C000
+#define  PORTSCX_PORT_TEST_CTRL               0x000F0000
+#define  PORTSCX_WAKE_ON_CONNECT_EN           0x00100000
+#define  PORTSCX_WAKE_ON_CONNECT_DIS          0x00200000
+#define  PORTSCX_WAKE_ON_OVER_CURRENT         0x00400000
+#define  PORTSCX_PHY_LOW_POWER_SPD            0x00800000
+#define  PORTSCX_PORT_FORCE_FULL_SPEED        0x01000000
+#define  PORTSCX_PORT_SPEED_MASK              0x0C000000
+#define  PORTSCX_PORT_WIDTH                   0x10000000
+#define  PORTSCX_PHY_TYPE_SEL                 0xC0000000
+
+/* bit 11-10 are line status */
+#define  PORTSCX_LINE_STATUS_SE0              0x00000000
+#define  PORTSCX_LINE_STATUS_JSTATE           0x00000400
+#define  PORTSCX_LINE_STATUS_KSTATE           0x00000800
+#define  PORTSCX_LINE_STATUS_UNDEF            0x00000C00
+#define  PORTSCX_LINE_STATUS_BIT_POS          10
+
+/* bit 15-14 are port indicator control */
+#define  PORTSCX_PIC_OFF                      0x00000000
+#define  PORTSCX_PIC_AMBER                    0x00004000
+#define  PORTSCX_PIC_GREEN                    0x00008000
+#define  PORTSCX_PIC_UNDEF                    0x0000C000
+#define  PORTSCX_PIC_BIT_POS                  14
+
+/* bit 19-16 are port test control */
+#define  PORTSCX_PTC_DISABLE                  0x00000000
+#define  PORTSCX_PTC_JSTATE                   0x00010000
+#define  PORTSCX_PTC_KSTATE                   0x00020000
+#define  PORTSCX_PTC_SEQNAK                   0x00030000
+#define  PORTSCX_PTC_PACKET                   0x00040000
+#define  PORTSCX_PTC_FORCE_EN                 0x00050000
+#define  PORTSCX_PTC_BIT_POS                  16
+
+/* bit 27-26 are port speed */
+#define  PORTSCX_PORT_SPEED_FULL              0x00000000
+#define  PORTSCX_PORT_SPEED_LOW               0x04000000
+#define  PORTSCX_PORT_SPEED_HIGH              0x08000000
+#define  PORTSCX_PORT_SPEED_UNDEF             0x0C000000
+#define  PORTSCX_SPEED_BIT_POS                26
+
+/* bit 28 is parallel transceiver width for UTMI interface */
+#define  PORTSCX_PTW                          0x10000000
+#define  PORTSCX_PTW_8BIT                     0x00000000
+#define  PORTSCX_PTW_16BIT                    0x10000000
+
+/* bit 31-30 are port transceiver select */
+#define  PORTSCX_PTS_UTMI                     0x00000000
+#define  PORTSCX_PTS_ULPI                     0x80000000
+#define  PORTSCX_PTS_FSLS                     0xC0000000
+#define  PORTSCX_PTS_BIT_POS                  30
+
+/* otgsc Register Bit Masks */
+#define  OTGSC_CTRL_VUSB_DISCHARGE            0x00000001
+#define  OTGSC_CTRL_VUSB_CHARGE               0x00000002
+#define  OTGSC_CTRL_OTG_TERM                  0x00000008
+#define  OTGSC_CTRL_DATA_PULSING              0x00000010
+#define  OTGSC_STS_USB_ID                     0x00000100
+#define  OTGSC_STS_A_VBUS_VALID               0x00000200
+#define  OTGSC_STS_A_SESSION_VALID            0x00000400
+#define  OTGSC_STS_B_SESSION_VALID            0x00000800
+#define  OTGSC_STS_B_SESSION_END              0x00001000
+#define  OTGSC_STS_1MS_TOGGLE                 0x00002000
+#define  OTGSC_STS_DATA_PULSING               0x00004000
+#define  OTGSC_INTSTS_USB_ID                  0x00010000
+#define  OTGSC_INTSTS_A_VBUS_VALID            0x00020000
+#define  OTGSC_INTSTS_A_SESSION_VALID         0x00040000
+#define  OTGSC_INTSTS_B_SESSION_VALID         0x00080000
+#define  OTGSC_INTSTS_B_SESSION_END           0x00100000
+#define  OTGSC_INTSTS_1MS                     0x00200000
+#define  OTGSC_INTSTS_DATA_PULSING            0x00400000
+#define  OTGSC_INTR_USB_ID                    0x01000000
+#define  OTGSC_INTR_A_VBUS_VALID              0x02000000
+#define  OTGSC_INTR_A_SESSION_VALID           0x04000000
+#define  OTGSC_INTR_B_SESSION_VALID           0x08000000
+#define  OTGSC_INTR_B_SESSION_END             0x10000000
+#define  OTGSC_INTR_1MS_TIMER                 0x20000000
+#define  OTGSC_INTR_DATA_PULSING              0x40000000
+
+/* USB MODE Register Bit Masks */
+#define  USB_MODE_CTRL_MODE_IDLE              0x00000000
+#define  USB_MODE_CTRL_MODE_DEVICE            0x00000002
+#define  USB_MODE_CTRL_MODE_HOST              0x00000003
+#define  USB_MODE_CTRL_MODE_RSV               0x00000001
+#define  USB_MODE_SETUP_LOCK_OFF              0x00000008
+#define  USB_MODE_STREAM_DISABLE              0x00000010
+/* Endpoint Flush Register */
+#define EPFLUSH_TX_OFFSET		      0x00010000
+#define EPFLUSH_RX_OFFSET		      0x00000000
+
+/* Endpoint Setup Status bit masks */
+#define  EP_SETUP_STATUS_MASK                 0x0000003F
+#define  EP_SETUP_STATUS_EP0		      0x00000001
+
+/* ENDPOINTCTRLx  Register Bit Masks */
+#define  EPCTRL_TX_ENABLE                     0x00800000
+#define  EPCTRL_TX_DATA_TOGGLE_RST            0x00400000	/* Not EP0 */
+#define  EPCTRL_TX_DATA_TOGGLE_INH            0x00200000	/* Not EP0 */
+#define  EPCTRL_TX_TYPE                       0x000C0000
+#define  EPCTRL_TX_DATA_SOURCE                0x00020000	/* Not EP0 */
+#define  EPCTRL_TX_EP_STALL                   0x00010000
+#define  EPCTRL_RX_ENABLE                     0x00000080
+#define  EPCTRL_RX_DATA_TOGGLE_RST            0x00000040	/* Not EP0 */
+#define  EPCTRL_RX_DATA_TOGGLE_INH            0x00000020	/* Not EP0 */
+#define  EPCTRL_RX_TYPE                       0x0000000C
+#define  EPCTRL_RX_DATA_SINK                  0x00000002	/* Not EP0 */
+#define  EPCTRL_RX_EP_STALL                   0x00000001
+
+/* bit 19-18 and 3-2 are endpoint type */
+#define  EPCTRL_EP_TYPE_CONTROL               0
+#define  EPCTRL_EP_TYPE_ISO                   1
+#define  EPCTRL_EP_TYPE_BULK                  2
+#define  EPCTRL_EP_TYPE_INTERRUPT             3
+#define  EPCTRL_TX_EP_TYPE_SHIFT              18
+#define  EPCTRL_RX_EP_TYPE_SHIFT              2
+
+/* SNOOPn Register Bit Masks */
+#define  SNOOP_ADDRESS_MASK                   0xFFFFF000
+#define  SNOOP_SIZE_ZERO                      0x00	/* snooping disable */
+#define  SNOOP_SIZE_4KB                       0x0B	/* 4KB snoop size */
+#define  SNOOP_SIZE_8KB                       0x0C
+#define  SNOOP_SIZE_16KB                      0x0D
+#define  SNOOP_SIZE_32KB                      0x0E
+#define  SNOOP_SIZE_64KB                      0x0F
+#define  SNOOP_SIZE_128KB                     0x10
+#define  SNOOP_SIZE_256KB                     0x11
+#define  SNOOP_SIZE_512KB                     0x12
+#define  SNOOP_SIZE_1MB                       0x13
+#define  SNOOP_SIZE_2MB                       0x14
+#define  SNOOP_SIZE_4MB                       0x15
+#define  SNOOP_SIZE_8MB                       0x16
+#define  SNOOP_SIZE_16MB                      0x17
+#define  SNOOP_SIZE_32MB                      0x18
+#define  SNOOP_SIZE_64MB                      0x19
+#define  SNOOP_SIZE_128MB                     0x1A
+#define  SNOOP_SIZE_256MB                     0x1B
+#define  SNOOP_SIZE_512MB                     0x1C
+#define  SNOOP_SIZE_1GB                       0x1D
+#define  SNOOP_SIZE_2GB                       0x1E	/* 2GB snoop size */
+
+/* pri_ctrl Register Bit Masks */
+#define  PRI_CTRL_PRI_LVL1                    0x0000000C
+#define  PRI_CTRL_PRI_LVL0                    0x00000003
+
+/* si_ctrl Register Bit Masks */
+#define  SI_CTRL_ERR_DISABLE                  0x00000010
+#define  SI_CTRL_IDRC_DISABLE                 0x00000008
+#define  SI_CTRL_RD_SAFE_EN                   0x00000004
+#define  SI_CTRL_RD_PREFETCH_DISABLE          0x00000002
+#define  SI_CTRL_RD_PREFEFETCH_VAL            0x00000001
+
+/* control Register Bit Masks */
+#define  USB_CTRL_IOENB                       0x00000004
+#define  USB_CTRL_ULPI_INT0EN                 0x00000001
+
+/* Endpoint Queue Head data struct
+ * Rem: all the variables of qh are LittleEndian Mode
+ * and NEXT_POINTER_MASK should operate on a LittleEndian, Phy Addr
+ */
+struct ep_queue_head {
+	u32 max_pkt_length;	/* Mult(31-30) , Zlt(29) , Max Pkt len
+				   and IOS(15) */
+	u32 curr_dtd_ptr;	/* Current dTD Pointer(31-5) */
+	u32 next_dtd_ptr;	/* Next dTD Pointer(31-5), T(0) */
+	u32 size_ioc_int_sts;	/* Total bytes (30-16), IOC (15),
+				   MultO(11-10), STS (7-0)  */
+	u32 buff_ptr0;		/* Buffer pointer Page 0 (31-12) */
+	u32 buff_ptr1;		/* Buffer pointer Page 1 (31-12) */
+	u32 buff_ptr2;		/* Buffer pointer Page 2 (31-12) */
+	u32 buff_ptr3;		/* Buffer pointer Page 3 (31-12) */
+	u32 buff_ptr4;		/* Buffer pointer Page 4 (31-12) */
+	u32 res1;
+	u8 setup_buffer[8];	/* Setup data 8 bytes */
+	u32 res2[4];
+};
+
+/* Endpoint Queue Head Bit Masks */
+#define  EP_QUEUE_HEAD_MULT_POS               30
+#define  EP_QUEUE_HEAD_ZLT_SEL                0x20000000
+#define  EP_QUEUE_HEAD_MAX_PKT_LEN_POS        16
+#define  EP_QUEUE_HEAD_MAX_PKT_LEN(ep_info)   (((ep_info)>>16)&0x07ff)
+#define  EP_QUEUE_HEAD_IOS                    0x00008000
+#define  EP_QUEUE_HEAD_NEXT_TERMINATE         0x00000001
+#define  EP_QUEUE_HEAD_IOC                    0x00008000
+#define  EP_QUEUE_HEAD_MULTO                  0x00000C00
+#define  EP_QUEUE_HEAD_STATUS_HALT	      0x00000040
+#define  EP_QUEUE_HEAD_STATUS_ACTIVE          0x00000080
+#define  EP_QUEUE_CURRENT_OFFSET_MASK         0x00000FFF
+#define  EP_QUEUE_HEAD_NEXT_POINTER_MASK      0xFFFFFFE0
+#define  EP_QUEUE_FRINDEX_MASK                0x000007FF
+#define  EP_MAX_LENGTH_TRANSFER               0x4000
+
+/* Endpoint Transfer Descriptor data struct */
+/* Rem: all the variables of td are LittleEndian Mode */
+struct ep_td_struct {
+	u32 next_td_ptr;	/* Next TD pointer(31-5), T(0) set
+				   indicate invalid */
+	u32 size_ioc_sts;	/* Total bytes (30-16), IOC (15),
+				   MultO(11-10), STS (7-0)  */
+	u32 buff_ptr0;		/* Buffer pointer Page 0 */
+	u32 buff_ptr1;		/* Buffer pointer Page 1 */
+	u32 buff_ptr2;		/* Buffer pointer Page 2 */
+	u32 buff_ptr3;		/* Buffer pointer Page 3 */
+	u32 buff_ptr4;		/* Buffer pointer Page 4 */
+	u32 res;
+	/* 32 bytes */
+	dma_addr_t td_dma;	/* dma address for this td */
+	/* virtual address of next td specified in next_td_ptr */
+	struct ep_td_struct *next_td_virt;
+};
+
+/* Endpoint Transfer Descriptor bit Masks */
+#define  DTD_NEXT_TERMINATE                   0x00000001
+#define  DTD_IOC                              0x00008000
+#define  DTD_STATUS_ACTIVE                    0x00000080
+#define  DTD_STATUS_HALTED                    0x00000040
+#define  DTD_STATUS_DATA_BUFF_ERR             0x00000020
+#define  DTD_STATUS_TRANSACTION_ERR           0x00000008
+#define  DTD_RESERVED_FIELDS                  0x80007300
+#define  DTD_ADDR_MASK                        0xFFFFFFE0
+#define  DTD_PACKET_SIZE                      0x7FFF0000
+#define  DTD_LENGTH_BIT_POS                   16
+#define  DTD_ERROR_MASK                       (DTD_STATUS_HALTED | \
+                                               DTD_STATUS_DATA_BUFF_ERR | \
+                                               DTD_STATUS_TRANSACTION_ERR)
+/* Alignment requirements; must be a power of two */
+#define DTD_ALIGNMENT				0x20
+#define QH_ALIGNMENT				2048
+
+/* Controller dma boundary */
+#define UDC_DMA_BOUNDARY			0x1000
+
+/* -----------------------------------------------------------------------*/
+/* ##### enum data
+*/
+typedef enum {
+	e_ULPI,
+	e_UTMI_8BIT,
+	e_UTMI_16BIT,
+	e_SERIAL
+} e_PhyInterface;
+
+/*-------------------------------------------------------------------------*/
+
+/* ### driver private data
+ */
+struct fsl_req {
+	struct usb_request req;
+	struct list_head queue;
+	/* ep_queue() func will add
+	   a request->queue into a udc_ep->queue 'd tail */
+	struct fsl_ep *ep;
+	unsigned mapped:1;
+
+	struct ep_td_struct *head, *tail;	/* For dTD List
+						   cpu endian Virtual addr */
+	unsigned int dtd_count;
+};
+
+#define REQ_UNCOMPLETE			1
+
+struct fsl_ep {
+	struct usb_ep ep;
+	struct list_head queue;
+	struct fsl_udc *udc;
+	struct ep_queue_head *qh;
+	const struct usb_endpoint_descriptor *desc;
+	struct usb_gadget *gadget;
+
+	char name[14];
+	unsigned stopped:1;
+};
+
+#define EP_DIR_IN	1
+#define EP_DIR_OUT	0
+
+struct fsl_udc {
+
+	struct usb_gadget gadget;
+	struct usb_gadget_driver *driver;
+	struct fsl_ep *eps;
+	unsigned int max_ep;
+	unsigned int irq;
+
+	struct usb_ctrlrequest local_setup_buff;
+	spinlock_t lock;
+	struct otg_transceiver *transceiver;
+	unsigned softconnect:1;
+	unsigned vbus_active:1;
+	unsigned stopped:1;
+	unsigned remote_wakeup:1;
+
+	struct ep_queue_head *ep_qh;	/* Endpoints Queue-Head */
+	struct fsl_req *status_req;	/* ep0 status request */
+	struct dma_pool *td_pool;	/* dma pool for DTD */
+	enum fsl_usb2_phy_modes phy_mode;
+
+	size_t ep_qh_size;		/* size after alignment adjustment*/
+	dma_addr_t ep_qh_dma;		/* dma address of QH */
+
+	u32 max_pipes;		/* Device max pipes */
+	u32 max_use_endpts;	/* Max endpointes to be used */
+	u32 bus_reset;		/* Device is bus reseting */
+	u32 resume_state;	/* USB state to resume */
+	u32 usb_state;		/* USB current state */
+	u32 usb_next_state;	/* USB next state */
+	u32 ep0_state;		/* Endpoint zero state */
+	u32 ep0_dir;		/* Endpoint zero direction: can be
+				   USB_DIR_IN or USB_DIR_OUT */
+	u32 usb_sof_count;	/* SOF count */
+	u32 errors;		/* USB ERRORs count */
+	u8 device_address;	/* Device USB address */
+
+	struct completion *done;	/* to make sure release() is done */
+};
+
+/*-------------------------------------------------------------------------*/
+
+#ifdef DEBUG
+#define DBG(fmt, args...) 	printk(KERN_DEBUG "[%s]  " fmt "\n", \
+				__FUNCTION__, ## args)
+#else
+#define DBG(fmt, args...)	do{}while(0)
+#endif
+
+#if 0
+static void dump_msg(const char *label, const u8 * buf, unsigned int length)
+{
+	unsigned int start, num, i;
+	char line[52], *p;
+
+	if (length >= 512)
+		return;
+	DBG("%s, length %u:\n", label, length);
+	start = 0;
+	while (length > 0) {
+		num = min(length, 16u);
+		p = line;
+		for (i = 0; i < num; ++i) {
+			if (i == 8)
+				*p++ = ' ';
+			sprintf(p, " %02x", buf[i]);
+			p += 3;
+		}
+		*p = 0;
+		printk(KERN_DEBUG "%6x: %s\n", start, line);
+		buf += num;
+		start += num;
+		length -= num;
+	}
+}
+#endif
+
+#ifdef VERBOSE
+#define VDBG		DBG
+#else
+#define VDBG(stuff...)	do{}while(0)
+#endif
+
+#define ERR(stuff...)		printk(KERN_ERR "udc: " stuff)
+#define WARN(stuff...)		printk(KERN_WARNING "udc: " stuff)
+#define INFO(stuff...)		printk(KERN_INFO "udc: " stuff)
+
+/*-------------------------------------------------------------------------*/
+
+/* ### Add board specific defines here
+ */
+
+/*
+ * ### pipe direction macro from device view
+ */
+#define USB_RECV	0	/* OUT EP */
+#define USB_SEND	1	/* IN EP */
+
+/*
+ * ### internal used help routines.
+ */
+#define ep_index(EP)		((EP)->desc->bEndpointAddress&0xF)
+#define ep_maxpacket(EP)	((EP)->ep.maxpacket)
+#define ep_is_in(EP)	( (ep_index(EP) == 0) ? (EP->udc->ep0_dir == \
+			USB_DIR_IN ):((EP)->desc->bEndpointAddress \
+			& USB_DIR_IN)==USB_DIR_IN)
+#define get_ep_by_pipe(udc, pipe)	((pipe == 1)? &udc->eps[0]: \
+					&udc->eps[pipe])
+#define get_pipe_by_windex(windex)	((windex & USB_ENDPOINT_NUMBER_MASK) \
+					* 2 + ((windex & USB_DIR_IN) ? 1 : 0))
+#define get_pipe_by_ep(EP)	(ep_index(EP) * 2 + ep_is_in(EP))
+
+#endif