diff options
| -rw-r--r-- | drivers/net/wireless/rt2x00/Kconfig | 5 | ||||
| -rw-r--r-- | drivers/net/wireless/rt2x00/Makefile | 1 | ||||
| -rw-r--r-- | drivers/net/wireless/rt2x00/rt2x00config.c | 28 | ||||
| -rw-r--r-- | drivers/net/wireless/rt2x00/rt2x00ht.c | 137 | ||||
| -rw-r--r-- | drivers/net/wireless/rt2x00/rt2x00lib.h | 24 | ||||
| -rw-r--r-- | drivers/net/wireless/rt2x00/rt2x00queue.c | 81 |
6 files changed, 108 insertions, 168 deletions
diff --git a/drivers/net/wireless/rt2x00/Kconfig b/drivers/net/wireless/rt2x00/Kconfig index d7e27b3..c457731 100644 --- a/drivers/net/wireless/rt2x00/Kconfig +++ b/drivers/net/wireless/rt2x00/Kconfig @@ -59,7 +59,6 @@ config RT2800PCI select RT2800_LIB select RT2X00_LIB_PCI if PCI select RT2X00_LIB_SOC if RALINK_RT288X || RALINK_RT305X - select RT2X00_LIB_HT select RT2X00_LIB_FIRMWARE select RT2X00_LIB_CRYPTO select CRC_CCITT @@ -133,7 +132,6 @@ config RT2800USB depends on USB select RT2800_LIB select RT2X00_LIB_USB - select RT2X00_LIB_HT select RT2X00_LIB_FIRMWARE select RT2X00_LIB_CRYPTO select CRC_CCITT @@ -196,9 +194,6 @@ config RT2X00_LIB_USB config RT2X00_LIB tristate -config RT2X00_LIB_HT - boolean - config RT2X00_LIB_FIRMWARE boolean select FW_LOADER diff --git a/drivers/net/wireless/rt2x00/Makefile b/drivers/net/wireless/rt2x00/Makefile index 9713398..349d5b8 100644 --- a/drivers/net/wireless/rt2x00/Makefile +++ b/drivers/net/wireless/rt2x00/Makefile @@ -7,7 +7,6 @@ rt2x00lib-$(CONFIG_RT2X00_LIB_DEBUGFS) += rt2x00debug.o rt2x00lib-$(CONFIG_RT2X00_LIB_CRYPTO) += rt2x00crypto.o rt2x00lib-$(CONFIG_RT2X00_LIB_FIRMWARE) += rt2x00firmware.o rt2x00lib-$(CONFIG_RT2X00_LIB_LEDS) += rt2x00leds.o -rt2x00lib-$(CONFIG_RT2X00_LIB_HT) += rt2x00ht.o obj-$(CONFIG_RT2X00_LIB) += rt2x00lib.o obj-$(CONFIG_RT2X00_LIB_PCI) += rt2x00pci.o diff --git a/drivers/net/wireless/rt2x00/rt2x00config.c b/drivers/net/wireless/rt2x00/rt2x00config.c index e225a66..f70a2b4 100644 --- a/drivers/net/wireless/rt2x00/rt2x00config.c +++ b/drivers/net/wireless/rt2x00/rt2x00config.c @@ -163,6 +163,34 @@ void rt2x00lib_config_antenna(struct rt2x00_dev *rt2x00dev, rt2x00queue_start_queue(rt2x00dev->rx); } +static u16 rt2x00ht_center_channel(struct rt2x00_dev *rt2x00dev, + struct ieee80211_conf *conf) +{ + struct hw_mode_spec *spec = &rt2x00dev->spec; + int center_channel; + u16 i; + + /* + * Initialize center channel to current channel. + */ + center_channel = spec->channels[conf->channel->hw_value].channel; + + /* + * Adjust center channel to HT40+ and HT40- operation. + */ + if (conf_is_ht40_plus(conf)) + center_channel += 2; + else if (conf_is_ht40_minus(conf)) + center_channel -= (center_channel == 14) ? 1 : 2; + + for (i = 0; i < spec->num_channels; i++) + if (spec->channels[i].channel == center_channel) + return i; + + WARN_ON(1); + return conf->channel->hw_value; +} + void rt2x00lib_config(struct rt2x00_dev *rt2x00dev, struct ieee80211_conf *conf, unsigned int ieee80211_flags) diff --git a/drivers/net/wireless/rt2x00/rt2x00ht.c b/drivers/net/wireless/rt2x00/rt2x00ht.c deleted file mode 100644 index a30f68c..0000000 --- a/drivers/net/wireless/rt2x00/rt2x00ht.c +++ /dev/null @@ -1,137 +0,0 @@ -/* - Copyright (C) 2004 - 2009 Ivo van Doorn <IvDoorn@gmail.com> - <http://rt2x00.serialmonkey.com> - - This program is free software; you can redistribute it and/or modify - it under the terms of the GNU General Public License as published by - the Free Software Foundation; either version 2 of the License, or - (at your option) any later version. - - This program is distributed in the hope that it will be useful, - but WITHOUT ANY WARRANTY; without even the implied warranty of - MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - GNU General Public License for more details. - - You should have received a copy of the GNU General Public License - along with this program; if not, write to the - Free Software Foundation, Inc., - 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA. - */ - -/* - Module: rt2x00lib - Abstract: rt2x00 HT specific routines. - */ - -#include <linux/kernel.h> -#include <linux/module.h> - -#include "rt2x00.h" -#include "rt2x00lib.h" - -void rt2x00ht_create_tx_descriptor(struct queue_entry *entry, - struct txentry_desc *txdesc, - const struct rt2x00_rate *hwrate) -{ - struct ieee80211_tx_info *tx_info = IEEE80211_SKB_CB(entry->skb); - struct ieee80211_tx_rate *txrate = &tx_info->control.rates[0]; - struct ieee80211_hdr *hdr = (struct ieee80211_hdr *)entry->skb->data; - - if (tx_info->control.sta) - txdesc->u.ht.mpdu_density = - tx_info->control.sta->ht_cap.ampdu_density; - - txdesc->u.ht.ba_size = 7; /* FIXME: What value is needed? */ - - /* - * Only one STBC stream is supported for now. - */ - if (tx_info->flags & IEEE80211_TX_CTL_STBC) - txdesc->u.ht.stbc = 1; - - /* - * If IEEE80211_TX_RC_MCS is set txrate->idx just contains the - * mcs rate to be used - */ - if (txrate->flags & IEEE80211_TX_RC_MCS) { - txdesc->u.ht.mcs = txrate->idx; - - /* - * MIMO PS should be set to 1 for STA's using dynamic SM PS - * when using more then one tx stream (>MCS7). - */ - if (tx_info->control.sta && txdesc->u.ht.mcs > 7 && - ((tx_info->control.sta->ht_cap.cap & - IEEE80211_HT_CAP_SM_PS) >> - IEEE80211_HT_CAP_SM_PS_SHIFT) == - WLAN_HT_CAP_SM_PS_DYNAMIC) - __set_bit(ENTRY_TXD_HT_MIMO_PS, &txdesc->flags); - } else { - txdesc->u.ht.mcs = rt2x00_get_rate_mcs(hwrate->mcs); - if (txrate->flags & IEEE80211_TX_RC_USE_SHORT_PREAMBLE) - txdesc->u.ht.mcs |= 0x08; - } - - /* - * This frame is eligible for an AMPDU, however, don't aggregate - * frames that are intended to probe a specific tx rate. - */ - if (tx_info->flags & IEEE80211_TX_CTL_AMPDU && - !(tx_info->flags & IEEE80211_TX_CTL_RATE_CTRL_PROBE)) - __set_bit(ENTRY_TXD_HT_AMPDU, &txdesc->flags); - - /* - * Set 40Mhz mode if necessary (for legacy rates this will - * duplicate the frame to both channels). - */ - if (txrate->flags & IEEE80211_TX_RC_40_MHZ_WIDTH || - txrate->flags & IEEE80211_TX_RC_DUP_DATA) - __set_bit(ENTRY_TXD_HT_BW_40, &txdesc->flags); - if (txrate->flags & IEEE80211_TX_RC_SHORT_GI) - __set_bit(ENTRY_TXD_HT_SHORT_GI, &txdesc->flags); - - /* - * Determine IFS values - * - Use TXOP_BACKOFF for management frames except beacons - * - Use TXOP_SIFS for fragment bursts - * - Use TXOP_HTTXOP for everything else - * - * Note: rt2800 devices won't use CTS protection (if used) - * for frames not transmitted with TXOP_HTTXOP - */ - if (ieee80211_is_mgmt(hdr->frame_control) && - !ieee80211_is_beacon(hdr->frame_control)) - txdesc->u.ht.txop = TXOP_BACKOFF; - else if (!(tx_info->flags & IEEE80211_TX_CTL_FIRST_FRAGMENT)) - txdesc->u.ht.txop = TXOP_SIFS; - else - txdesc->u.ht.txop = TXOP_HTTXOP; -} - -u16 rt2x00ht_center_channel(struct rt2x00_dev *rt2x00dev, - struct ieee80211_conf *conf) -{ - struct hw_mode_spec *spec = &rt2x00dev->spec; - int center_channel; - u16 i; - - /* - * Initialize center channel to current channel. - */ - center_channel = spec->channels[conf->channel->hw_value].channel; - - /* - * Adjust center channel to HT40+ and HT40- operation. - */ - if (conf_is_ht40_plus(conf)) - center_channel += 2; - else if (conf_is_ht40_minus(conf)) - center_channel -= (center_channel == 14) ? 1 : 2; - - for (i = 0; i < spec->num_channels; i++) - if (spec->channels[i].channel == center_channel) - return i; - - WARN_ON(1); - return conf->channel->hw_value; -} diff --git a/drivers/net/wireless/rt2x00/rt2x00lib.h b/drivers/net/wireless/rt2x00/rt2x00lib.h index 57ede6c..322cc4f 100644 --- a/drivers/net/wireless/rt2x00/rt2x00lib.h +++ b/drivers/net/wireless/rt2x00/rt2x00lib.h @@ -388,30 +388,6 @@ static inline void rt2x00crypto_rx_insert_iv(struct sk_buff *skb, #endif /* CONFIG_RT2X00_LIB_CRYPTO */ /* - * HT handlers. - */ -#ifdef CONFIG_RT2X00_LIB_HT -void rt2x00ht_create_tx_descriptor(struct queue_entry *entry, - struct txentry_desc *txdesc, - const struct rt2x00_rate *hwrate); - -u16 rt2x00ht_center_channel(struct rt2x00_dev *rt2x00dev, - struct ieee80211_conf *conf); -#else -static inline void rt2x00ht_create_tx_descriptor(struct queue_entry *entry, - struct txentry_desc *txdesc, - const struct rt2x00_rate *hwrate) -{ -} - -static inline u16 rt2x00ht_center_channel(struct rt2x00_dev *rt2x00dev, - struct ieee80211_conf *conf) -{ - return conf->channel->hw_value; -} -#endif /* CONFIG_RT2X00_LIB_HT */ - -/* * RFkill handlers. */ static inline void rt2x00rfkill_register(struct rt2x00_dev *rt2x00dev) diff --git a/drivers/net/wireless/rt2x00/rt2x00queue.c b/drivers/net/wireless/rt2x00/rt2x00queue.c index 0d79278..56f9d0d 100644 --- a/drivers/net/wireless/rt2x00/rt2x00queue.c +++ b/drivers/net/wireless/rt2x00/rt2x00queue.c @@ -302,6 +302,85 @@ static void rt2x00queue_create_tx_descriptor_plcp(struct queue_entry *entry, } } +static void rt2x00queue_create_tx_descriptor_ht(struct queue_entry *entry, + struct txentry_desc *txdesc, + const struct rt2x00_rate *hwrate) +{ + struct ieee80211_tx_info *tx_info = IEEE80211_SKB_CB(entry->skb); + struct ieee80211_tx_rate *txrate = &tx_info->control.rates[0]; + struct ieee80211_hdr *hdr = (struct ieee80211_hdr *)entry->skb->data; + + if (tx_info->control.sta) + txdesc->u.ht.mpdu_density = + tx_info->control.sta->ht_cap.ampdu_density; + + txdesc->u.ht.ba_size = 7; /* FIXME: What value is needed? */ + + /* + * Only one STBC stream is supported for now. + */ + if (tx_info->flags & IEEE80211_TX_CTL_STBC) + txdesc->u.ht.stbc = 1; + + /* + * If IEEE80211_TX_RC_MCS is set txrate->idx just contains the + * mcs rate to be used + */ + if (txrate->flags & IEEE80211_TX_RC_MCS) { + txdesc->u.ht.mcs = txrate->idx; + + /* + * MIMO PS should be set to 1 for STA's using dynamic SM PS + * when using more then one tx stream (>MCS7). + */ + if (tx_info->control.sta && txdesc->u.ht.mcs > 7 && + ((tx_info->control.sta->ht_cap.cap & + IEEE80211_HT_CAP_SM_PS) >> + IEEE80211_HT_CAP_SM_PS_SHIFT) == + WLAN_HT_CAP_SM_PS_DYNAMIC) + __set_bit(ENTRY_TXD_HT_MIMO_PS, &txdesc->flags); + } else { + txdesc->u.ht.mcs = rt2x00_get_rate_mcs(hwrate->mcs); + if (txrate->flags & IEEE80211_TX_RC_USE_SHORT_PREAMBLE) + txdesc->u.ht.mcs |= 0x08; + } + + /* + * This frame is eligible for an AMPDU, however, don't aggregate + * frames that are intended to probe a specific tx rate. + */ + if (tx_info->flags & IEEE80211_TX_CTL_AMPDU && + !(tx_info->flags & IEEE80211_TX_CTL_RATE_CTRL_PROBE)) + __set_bit(ENTRY_TXD_HT_AMPDU, &txdesc->flags); + + /* + * Set 40Mhz mode if necessary (for legacy rates this will + * duplicate the frame to both channels). + */ + if (txrate->flags & IEEE80211_TX_RC_40_MHZ_WIDTH || + txrate->flags & IEEE80211_TX_RC_DUP_DATA) + __set_bit(ENTRY_TXD_HT_BW_40, &txdesc->flags); + if (txrate->flags & IEEE80211_TX_RC_SHORT_GI) + __set_bit(ENTRY_TXD_HT_SHORT_GI, &txdesc->flags); + + /* + * Determine IFS values + * - Use TXOP_BACKOFF for management frames except beacons + * - Use TXOP_SIFS for fragment bursts + * - Use TXOP_HTTXOP for everything else + * + * Note: rt2800 devices won't use CTS protection (if used) + * for frames not transmitted with TXOP_HTTXOP + */ + if (ieee80211_is_mgmt(hdr->frame_control) && + !ieee80211_is_beacon(hdr->frame_control)) + txdesc->u.ht.txop = TXOP_BACKOFF; + else if (!(tx_info->flags & IEEE80211_TX_CTL_FIRST_FRAGMENT)) + txdesc->u.ht.txop = TXOP_SIFS; + else + txdesc->u.ht.txop = TXOP_HTTXOP; +} + static void rt2x00queue_create_tx_descriptor(struct queue_entry *entry, struct txentry_desc *txdesc) { @@ -397,7 +476,7 @@ static void rt2x00queue_create_tx_descriptor(struct queue_entry *entry, rt2x00queue_create_tx_descriptor_seq(entry, txdesc); if (test_bit(REQUIRE_HT_TX_DESC, &rt2x00dev->cap_flags)) - rt2x00ht_create_tx_descriptor(entry, txdesc, hwrate); + rt2x00queue_create_tx_descriptor_ht(entry, txdesc, hwrate); else rt2x00queue_create_tx_descriptor_plcp(entry, txdesc, hwrate); } |