diff options
Diffstat (limited to 'Documentation/blockdev/zram.txt')
-rw-r--r-- | Documentation/blockdev/zram.txt | 119 |
1 files changed, 119 insertions, 0 deletions
diff --git a/Documentation/blockdev/zram.txt b/Documentation/blockdev/zram.txt new file mode 100644 index 0000000..986b923 --- /dev/null +++ b/Documentation/blockdev/zram.txt @@ -0,0 +1,119 @@ +zram: Compressed RAM based block devices +---------------------------------------- + +Project home: http://compcache.googlecode.com/ + +* Introduction + +The zram module creates RAM based block devices named /dev/zram<id> +(<id> = 0, 1, ...). Pages written to these disks are compressed and stored +in memory itself. These disks allow very fast I/O and compression provides +good amounts of memory savings. Some of the usecases include /tmp storage, +use as swap disks, various caches under /var and maybe many more :) + +Statistics for individual zram devices are exported through sysfs nodes at +/sys/block/zram<id>/ + +* Usage + +Following shows a typical sequence of steps for using zram. + +1) Load Module: + modprobe zram num_devices=4 + This creates 4 devices: /dev/zram{0,1,2,3} + (num_devices parameter is optional. Default: 1) + +2) Set max number of compression streams + Compression backend may use up to max_comp_streams compression streams, + thus allowing up to max_comp_streams concurrent compression operations. + By default, compression backend uses single compression stream. + + Examples: + #show max compression streams number + cat /sys/block/zram0/max_comp_streams + + #set max compression streams number to 3 + echo 3 > /sys/block/zram0/max_comp_streams + +Note: +In order to enable compression backend's multi stream support max_comp_streams +must be initially set to desired concurrency level before ZRAM device +initialisation. Once the device initialised as a single stream compression +backend (max_comp_streams equals to 1), you will see error if you try to change +the value of max_comp_streams because single stream compression backend +implemented as a special case by lock overhead issue and does not support +dynamic max_comp_streams. Only multi stream backend supports dynamic +max_comp_streams adjustment. + +3) Select compression algorithm + Using comp_algorithm device attribute one can see available and + currently selected (shown in square brackets) compression algortithms, + change selected compression algorithm (once the device is initialised + there is no way to change compression algorithm). + + Examples: + #show supported compression algorithms + cat /sys/block/zram0/comp_algorithm + lzo [lz4] + + #select lzo compression algorithm + echo lzo > /sys/block/zram0/comp_algorithm + +4) Set Disksize + Set disk size by writing the value to sysfs node 'disksize'. + The value can be either in bytes or you can use mem suffixes. + Examples: + # Initialize /dev/zram0 with 50MB disksize + echo $((50*1024*1024)) > /sys/block/zram0/disksize + + # Using mem suffixes + echo 256K > /sys/block/zram0/disksize + echo 512M > /sys/block/zram0/disksize + echo 1G > /sys/block/zram0/disksize + +Note: +There is little point creating a zram of greater than twice the size of memory +since we expect a 2:1 compression ratio. Note that zram uses about 0.1% of the +size of the disk when not in use so a huge zram is wasteful. + +5) Activate: + mkswap /dev/zram0 + swapon /dev/zram0 + + mkfs.ext4 /dev/zram1 + mount /dev/zram1 /tmp + +6) Stats: + Per-device statistics are exported as various nodes under + /sys/block/zram<id>/ + disksize + num_reads + num_writes + failed_reads + failed_writes + invalid_io + notify_free + zero_pages + orig_data_size + compr_data_size + mem_used_total + +7) Deactivate: + swapoff /dev/zram0 + umount /dev/zram1 + +8) Reset: + Write any positive value to 'reset' sysfs node + echo 1 > /sys/block/zram0/reset + echo 1 > /sys/block/zram1/reset + + This frees all the memory allocated for the given device and + resets the disksize to zero. You must set the disksize again + before reusing the device. + +Please report any problems at: + - Mailing list: linux-mm-cc at laptop dot org + - Issue tracker: http://code.google.com/p/compcache/issues/list + +Nitin Gupta +ngupta@vflare.org |