3 files changed, 0 insertions, 127 deletions
diff --git a/Documentation/powerpc/dts-bindings/gpio/gpio.txt b/Documentation/powerpc/dts-bindings/gpio/gpio.txt
deleted file mode 100644
index edaa84d..0000000
--- a/Documentation/powerpc/dts-bindings/gpio/gpio.txt
+++ /dev/null
@@ -1,50 +0,0 @@
-Specifying GPIO information for devices
-============================================
-
-1) gpios property
------------------
-
-Nodes that makes use of GPIOs should define them using `gpios' property,
-format of which is: <&gpio-controller1-phandle gpio1-specifier
-		     &gpio-controller2-phandle gpio2-specifier
-		     0 /* holes are permitted, means no GPIO 3 */
-		     &gpio-controller4-phandle gpio4-specifier
-		     ...>;
-
-Note that gpio-specifier length is controller dependent.
-
-gpio-specifier may encode: bank, pin position inside the bank,
-whether pin is open-drain and whether pin is logically inverted.
-
-Example of the node using GPIOs:
-
-	node {
-		gpios = <&qe_pio_e 18 0>;
-	};
-
-In this example gpio-specifier is "18 0" and encodes GPIO pin number,
-and empty GPIO flags as accepted by the "qe_pio_e" gpio-controller.
-
-2) gpio-controller nodes
-------------------------
-
-Every GPIO controller node must have #gpio-cells property defined,
-this information will be used to translate gpio-specifiers.
-
-Example of two SOC GPIO banks defined as gpio-controller nodes:
-
-	qe_pio_a: gpio-controller@1400 {
-		#gpio-cells = <2>;
-		compatible = "fsl,qe-pario-bank-a", "fsl,qe-pario-bank";
-		reg = <0x1400 0x18>;
-		gpio-controller;
-	};
-
-	qe_pio_e: gpio-controller@1460 {
-		#gpio-cells = <2>;
-		compatible = "fsl,qe-pario-bank-e", "fsl,qe-pario-bank";
-		reg = <0x1460 0x18>;
-		gpio-controller;
-	};
-
-
diff --git a/Documentation/powerpc/dts-bindings/gpio/led.txt b/Documentation/powerpc/dts-bindings/gpio/led.txt
deleted file mode 100644
index 064db92..0000000
--- a/Documentation/powerpc/dts-bindings/gpio/led.txt
+++ /dev/null
@@ -1,58 +0,0 @@
-LEDs connected to GPIO lines
-
-Required properties:
-- compatible : should be "gpio-leds".
-
-Each LED is represented as a sub-node of the gpio-leds device.  Each
-node's name represents the name of the corresponding LED.
-
-LED sub-node properties:
-- gpios :  Should specify the LED's GPIO, see "Specifying GPIO information
-  for devices" in Documentation/powerpc/booting-without-of.txt.  Active
-  low LEDs should be indicated using flags in the GPIO specifier.
-- label :  (optional) The label for this LED.  If omitted, the label is
-  taken from the node name (excluding the unit address).
-- linux,default-trigger :  (optional) This parameter, if present, is a
-  string defining the trigger assigned to the LED.  Current triggers are:
-    "backlight" - LED will act as a back-light, controlled by the framebuffer
-		  system
-    "default-on" - LED will turn on, but see "default-state" below
-    "heartbeat" - LED "double" flashes at a load average based rate
-    "ide-disk" - LED indicates disk activity
-    "timer" - LED flashes at a fixed, configurable rate
-- default-state:  (optional) The initial state of the LED.  Valid
-  values are "on", "off", and "keep".  If the LED is already on or off
-  and the default-state property is set the to same value, then no
-  glitch should be produced where the LED momentarily turns off (or
-  on).  The "keep" setting will keep the LED at whatever its current
-  state is, without producing a glitch.  The default is off if this
-  property is not present.
-
-Examples:
-
-leds {
-	compatible = "gpio-leds";
-	hdd {
-		label = "IDE Activity";
-		gpios = <&mcu_pio 0 1>; /* Active low */
-		linux,default-trigger = "ide-disk";
-	};
-
-	fault {
-		gpios = <&mcu_pio 1 0>;
-		/* Keep LED on if BIOS detected hardware fault */
-		default-state = "keep";
-	};
-};
-
-run-control {
-	compatible = "gpio-leds";
-	red {
-		gpios = <&mpc8572 6 0>;
-		default-state = "off";
-	};
-	green {
-		gpios = <&mpc8572 7 0>;
-		default-state = "on";
-	};
-}
diff --git a/Documentation/powerpc/dts-bindings/gpio/mdio.txt b/Documentation/powerpc/dts-bindings/gpio/mdio.txt
deleted file mode 100644
index bc95495..0000000
--- a/Documentation/powerpc/dts-bindings/gpio/mdio.txt
+++ /dev/null
@@ -1,19 +0,0 @@
-MDIO on GPIOs
-
-Currently defined compatibles:
-- virtual,gpio-mdio
-
-MDC and MDIO lines connected to GPIO controllers are listed in the
-gpios property as described in section VIII.1 in the following order:
-
-MDC, MDIO.
-
-Example:
-
-mdio {
-	compatible = "virtual,mdio-gpio";
-	#address-cells = <1>;
-	#size-cells = <0>;
-	gpios = <&qe_pio_a 11
-		 &qe_pio_c 6>;
-};