diff options
Diffstat (limited to 'arch/arm/mach-exynos/Kconfig')
| -rw-r--r-- | arch/arm/mach-exynos/Kconfig | 43 |
1 files changed, 42 insertions, 1 deletions
diff --git a/arch/arm/mach-exynos/Kconfig b/arch/arm/mach-exynos/Kconfig index 2c177ec..b4dc72f 100644 --- a/arch/arm/mach-exynos/Kconfig +++ b/arch/arm/mach-exynos/Kconfig @@ -956,7 +956,7 @@ config PANEL_U1_NA_SPR endchoice -if MACH_U1 || MACH_C1 || MACH_M3 || MACH_M0 || MACH_P4 || MACH_P2 || MACH_P4NOTE || MACH_T0 || MACH_TRATS || MACH_GRANDE || MACH_GC1 || MACH_BAFFIN +if MACH_U1 || MACH_C1 || MACH_M3 || MACH_M0 || MACH_P4 || MACH_P2 || MACH_P4NOTE || MACH_T0 || MACH_TRATS || MACH_GRANDE || MACH_GC1 || MACH_BAFFIN || MACH_KONA source "arch/arm/mach-exynos/Kconfig.local" endif @@ -1090,6 +1090,11 @@ config MACH_T0 select S3C_DEV_I2C4 select S3C_DEV_I2C5 +config MACH_KONA + bool "KONA Note8 board" + select S3C_DEV_I2C4 + select S3C_DEV_I2C5 + config MACH_IRON bool "Iron board" select S3C_DEV_I2C4 @@ -1129,6 +1134,14 @@ config T0_04_BD bool "T0 Revison 04 board" default n +config KONA_00_BD + bool "KONA note8 rev00 common Board" + default n + +config KONA_01_BD + bool "KONA note8 rev01 common Board" + default n + config IRON_BD bool "Iron common Board" @@ -1152,6 +1165,9 @@ config JACK_FET config JACK_GROUND_DET bool "Ear Ground Detection Enable" +config USE_ADC_DET + bool "Jack Detection with ADC IC" + config SAMSUNG_ANALOG_UART_SWITCH int "SAMSUNG analog switch for UART" default 1 @@ -1599,6 +1615,16 @@ config EHCI_IRQ_DISTRIBUTION bool "ehci irq distribution" default n +if (LINK_DEVICE_USB || LINK_DEVICE_HSIC) +config EHCI_MODEM_PORTNUM + int "EHCI port number of modem connection" + default 2 +config CMC_MODEM_HSIC_SYSREV + int "System revision number which CMC modem support HSIC i/f" + depends on LTE_MODEM_CMC221 + default 9 +endif + if SEC_MODEM comment "Samsung Modem Feature" @@ -1726,6 +1752,11 @@ endchoice endif +comment "Connectivity Feature" +config GPS_BRCM_475X + bool "BRCM_475X_CHIPSET" + default n + if BT config BT_CSR8811 bool "Enable CSR8811 driver" @@ -1817,3 +1848,13 @@ config CORESIGHT_ETM_DEFAULT_ENABLE help Turns on ETM tracing by default. Otherwise, tracing is disabled by default but can be enabled by other means. + + +config MACH_KONA_SENSOR + bool "KONA Sensor Enable" + help + Support sensors of KONA boards + + BMA254 / BOSCH + YAS532 / YAMAHA + GP2A030A / SHARP |