diff options
Diffstat (limited to 'arch/arm/mach-omap2/hsmmc.c')
| -rw-r--r-- | arch/arm/mach-omap2/hsmmc.c | 55 |
1 files changed, 12 insertions, 43 deletions
diff --git a/arch/arm/mach-omap2/hsmmc.c b/arch/arm/mach-omap2/hsmmc.c index 66868c5..f4a1020 100644 --- a/arch/arm/mach-omap2/hsmmc.c +++ b/arch/arm/mach-omap2/hsmmc.c @@ -13,6 +13,7 @@ #include <linux/slab.h> #include <linux/string.h> #include <linux/delay.h> +#include <linux/gpio.h> #include <mach/hardware.h> #include <plat/mmc.h> #include <plat/omap-pm.h> @@ -128,16 +129,11 @@ static void omap4_hsmmc1_before_set_reg(struct device *dev, int slot, * Assume we power both OMAP VMMC1 (for CMD, CLK, DAT0..3) and the * card with Vcc regulator (from twl4030 or whatever). OMAP has both * 1.8V and 3.0V modes, controlled by the PBIAS register. - * - * In 8-bit modes, OMAP VMMC1A (for DAT4..7) needs a supply, which - * is most naturally TWL VSIM; those pins also use PBIAS. - * - * FIXME handle VMMC1A as needed ... */ reg = omap4_ctrl_pad_readl(control_pbias_offset); reg &= ~(OMAP4_MMC1_PBIASLITE_PWRDNZ_MASK | OMAP4_MMC1_PWRDNZ_MASK | - OMAP4_USBC1_ICUSB_PWRDNZ_MASK); + OMAP4_MMC1_PBIASLITE_VMODE_MASK); omap4_ctrl_pad_writel(reg, control_pbias_offset); } @@ -155,8 +151,7 @@ static void omap4_hsmmc1_after_set_reg(struct device *dev, int slot, else reg |= OMAP4_MMC1_PBIASLITE_VMODE_MASK; reg |= (OMAP4_MMC1_PBIASLITE_PWRDNZ_MASK | - OMAP4_MMC1_PWRDNZ_MASK | - OMAP4_USBC1_ICUSB_PWRDNZ_MASK); + OMAP4_MMC1_PWRDNZ_MASK); omap4_ctrl_pad_writel(reg, control_pbias_offset); timeout = jiffies + msecs_to_jiffies(5); @@ -170,17 +165,9 @@ static void omap4_hsmmc1_after_set_reg(struct device *dev, int slot, if (reg & OMAP4_MMC1_PBIASLITE_VMODE_ERROR_MASK) { pr_err("Pbias Voltage is not same as LDO\n"); /* Caution : On VMODE_ERROR Power Down MMC IO */ - reg &= ~(OMAP4_MMC1_PWRDNZ_MASK | - OMAP4_USBC1_ICUSB_PWRDNZ_MASK); + reg &= ~(OMAP4_MMC1_PWRDNZ_MASK); omap4_ctrl_pad_writel(reg, control_pbias_offset); } - } else { - reg = omap4_ctrl_pad_readl(control_pbias_offset); - reg |= (OMAP4_MMC1_PBIASLITE_PWRDNZ_MASK | - OMAP4_MMC1_PWRDNZ_MASK | - OMAP4_MMC1_PBIASLITE_VMODE_MASK | - OMAP4_USBC1_ICUSB_PWRDNZ_MASK); - omap4_ctrl_pad_writel(reg, control_pbias_offset); } } @@ -213,12 +200,10 @@ static int nop_mmc_set_power(struct device *dev, int slot, int power_on, static inline void omap_hsmmc_mux(struct omap_mmc_platform_data *mmc_controller, int controller_nr) { - if ((mmc_controller->slots[0].switch_pin > 0) && \ - (mmc_controller->slots[0].switch_pin < OMAP_MAX_GPIO_LINES)) + if (gpio_is_valid(mmc_controller->slots[0].switch_pin)) omap_mux_init_gpio(mmc_controller->slots[0].switch_pin, OMAP_PIN_INPUT_PULLUP); - if ((mmc_controller->slots[0].gpio_wp > 0) && \ - (mmc_controller->slots[0].gpio_wp < OMAP_MAX_GPIO_LINES)) + if (gpio_is_valid(mmc_controller->slots[0].gpio_wp)) omap_mux_init_gpio(mmc_controller->slots[0].gpio_wp, OMAP_PIN_INPUT_PULLUP); if (cpu_is_omap34xx()) { @@ -414,31 +399,17 @@ static int __init omap_hsmmc_pdata_init(struct omap2_hsmmc_info *c, return 0; } -static struct omap_device_pm_latency omap_hsmmc_latency[] = { - [0] = { - .deactivate_func = omap_device_idle_hwmods, - .activate_func = omap_device_enable_hwmods, - .flags = OMAP_DEVICE_LATENCY_AUTO_ADJUST, - }, - /* - * XXX There should also be an entry here to power off/on the - * MMC regulators/PBIAS cells, etc. - */ -}; - #define MAX_OMAP_MMC_HWMOD_NAME_LEN 16 void __init omap_init_hsmmc(struct omap2_hsmmc_info *hsmmcinfo, int ctrl_nr) { struct omap_hwmod *oh; - struct omap_device *od; - struct omap_device_pm_latency *ohl; + struct platform_device *pdev; char oh_name[MAX_OMAP_MMC_HWMOD_NAME_LEN]; struct omap_mmc_platform_data *mmc_data; struct omap_mmc_dev_attr *mmc_dev_attr; char *name; int l; - int ohl_cnt = 0; mmc_data = kzalloc(sizeof(struct omap_mmc_platform_data), GFP_KERNEL); if (!mmc_data) { @@ -453,8 +424,6 @@ void __init omap_init_hsmmc(struct omap2_hsmmc_info *hsmmcinfo, int ctrl_nr) omap_hsmmc_mux(mmc_data, (ctrl_nr - 1)); name = "omap_hsmmc"; - ohl = omap_hsmmc_latency; - ohl_cnt = ARRAY_SIZE(omap_hsmmc_latency); l = snprintf(oh_name, MAX_OMAP_MMC_HWMOD_NAME_LEN, "mmc%d", ctrl_nr); @@ -472,9 +441,9 @@ void __init omap_init_hsmmc(struct omap2_hsmmc_info *hsmmcinfo, int ctrl_nr) mmc_data->controller_flags = mmc_dev_attr->flags; } - od = omap_device_build(name, ctrl_nr - 1, oh, mmc_data, - sizeof(struct omap_mmc_platform_data), ohl, ohl_cnt, false); - if (IS_ERR(od)) { + pdev = omap_device_build(name, ctrl_nr - 1, oh, mmc_data, + sizeof(struct omap_mmc_platform_data), NULL, 0, false); + if (IS_ERR(pdev)) { WARN(1, "Can't build omap_device for %s:%s.\n", name, oh->name); kfree(mmc_data->slots[0].name); goto done; @@ -483,7 +452,7 @@ void __init omap_init_hsmmc(struct omap2_hsmmc_info *hsmmcinfo, int ctrl_nr) * return device handle to board setup code * required to populate for regulator framework structure */ - hsmmcinfo->dev = &od->pdev.dev; + hsmmcinfo->dev = &pdev->dev; done: kfree(mmc_data); @@ -510,7 +479,7 @@ void __init omap2_hsmmc_init(struct omap2_hsmmc_info *controllers) OMAP4_SDMMC1_PUSTRENGTH_GRP1_MASK); reg &= ~(OMAP4_SDMMC1_PUSTRENGTH_GRP2_MASK | OMAP4_SDMMC1_PUSTRENGTH_GRP3_MASK); - reg |= (OMAP4_USBC1_DR0_SPEEDCTRL_MASK| + reg |= (OMAP4_SDMMC1_DR0_SPEEDCTRL_MASK | OMAP4_SDMMC1_DR1_SPEEDCTRL_MASK | OMAP4_SDMMC1_DR2_SPEEDCTRL_MASK); omap4_ctrl_pad_writel(reg, control_mmc1); |