diff options
Diffstat (limited to 'arch/arm/plat-pxa/include/plat')
| -rw-r--r-- | arch/arm/plat-pxa/include/plat/gpio.h | 40 | ||||
| -rw-r--r-- | arch/arm/plat-pxa/include/plat/mfp.h | 2 | ||||
| -rw-r--r-- | arch/arm/plat-pxa/include/plat/pxa3xx_nand.h | 20 | ||||
| -rw-r--r-- | arch/arm/plat-pxa/include/plat/sdhci.h | 35 |
4 files changed, 22 insertions, 75 deletions
diff --git a/arch/arm/plat-pxa/include/plat/gpio.h b/arch/arm/plat-pxa/include/plat/gpio.h index 1ddd2b9..258f772 100644 --- a/arch/arm/plat-pxa/include/plat/gpio.h +++ b/arch/arm/plat-pxa/include/plat/gpio.h @@ -1,35 +1,10 @@ #ifndef __PLAT_GPIO_H #define __PLAT_GPIO_H -struct irq_data; +#define __ARM_GPIOLIB_COMPLEX -/* - * We handle the GPIOs by banks, each bank covers up to 32 GPIOs with - * one set of registers. The register offsets are organized below: - * - * GPLR GPDR GPSR GPCR GRER GFER GEDR - * BANK 0 - 0x0000 0x000C 0x0018 0x0024 0x0030 0x003C 0x0048 - * BANK 1 - 0x0004 0x0010 0x001C 0x0028 0x0034 0x0040 0x004C - * BANK 2 - 0x0008 0x0014 0x0020 0x002C 0x0038 0x0044 0x0050 - * - * BANK 3 - 0x0100 0x010C 0x0118 0x0124 0x0130 0x013C 0x0148 - * BANK 4 - 0x0104 0x0110 0x011C 0x0128 0x0134 0x0140 0x014C - * BANK 5 - 0x0108 0x0114 0x0120 0x012C 0x0138 0x0144 0x0150 - * - * NOTE: - * BANK 3 is only available on PXA27x and later processors. - * BANK 4 and 5 are only available on PXA935 - */ - -#define GPIO_BANK(n) (GPIO_REGS_VIRT + BANK_OFF(n)) - -#define GPLR_OFFSET 0x00 -#define GPDR_OFFSET 0x0C -#define GPSR_OFFSET 0x18 -#define GPCR_OFFSET 0x24 -#define GRER_OFFSET 0x30 -#define GFER_OFFSET 0x3C -#define GEDR_OFFSET 0x48 +/* The individual machine provides register offsets and NR_BUILTIN_GPIO */ +#include <mach/gpio-pxa.h> static inline int gpio_get_value(unsigned gpio) { @@ -52,13 +27,4 @@ static inline void gpio_set_value(unsigned gpio, int value) #define gpio_cansleep __gpio_cansleep -/* NOTE: some PXAs have fewer on-chip GPIOs (like PXA255, with 85). - * Those cases currently cause holes in the GPIO number space, the - * actual number of the last GPIO is recorded by 'pxa_last_gpio'. - */ -extern int pxa_last_gpio; - -typedef int (*set_wake_t)(struct irq_data *d, unsigned int on); - -extern void pxa_init_gpio(int mux_irq, int start, int end, set_wake_t fn); #endif /* __PLAT_GPIO_H */ diff --git a/arch/arm/plat-pxa/include/plat/mfp.h b/arch/arm/plat-pxa/include/plat/mfp.h index 89e68e0..5c79c29 100644 --- a/arch/arm/plat-pxa/include/plat/mfp.h +++ b/arch/arm/plat-pxa/include/plat/mfp.h @@ -456,7 +456,7 @@ struct mfp_addr_map { #define MFP_ADDR_END { MFP_PIN_INVALID, 0 } -void __init mfp_init_base(unsigned long mfpr_base); +void __init mfp_init_base(void __iomem *mfpr_base); void __init mfp_init_addr(struct mfp_addr_map *map); /* diff --git a/arch/arm/plat-pxa/include/plat/pxa3xx_nand.h b/arch/arm/plat-pxa/include/plat/pxa3xx_nand.h index 442301f..c42f39f 100644 --- a/arch/arm/plat-pxa/include/plat/pxa3xx_nand.h +++ b/arch/arm/plat-pxa/include/plat/pxa3xx_nand.h @@ -41,6 +41,19 @@ struct pxa3xx_nand_flash { struct pxa3xx_nand_timing *timing; /* NAND Flash timing */ }; +/* + * Current pxa3xx_nand controller has two chip select which + * both be workable. + * + * Notice should be taken that: + * When you want to use this feature, you should not enable the + * keep configuration feature, for two chip select could be + * attached with different nand chip. The different page size + * and timing requirement make the keep configuration impossible. + */ + +/* The max num of chip select current support */ +#define NUM_CHIP_SELECT (2) struct pxa3xx_nand_platform_data { /* the data flash bus is shared between the Static Memory @@ -52,8 +65,11 @@ struct pxa3xx_nand_platform_data { /* allow platform code to keep OBM/bootloader defined NFC config */ int keep_config; - const struct mtd_partition *parts; - unsigned int nr_parts; + /* indicate how many chip selects will be used */ + int num_cs; + + const struct mtd_partition *parts[NUM_CHIP_SELECT]; + unsigned int nr_parts[NUM_CHIP_SELECT]; const struct pxa3xx_nand_flash * flash; size_t num_flash; diff --git a/arch/arm/plat-pxa/include/plat/sdhci.h b/arch/arm/plat-pxa/include/plat/sdhci.h deleted file mode 100644 index 1ab332e..0000000 --- a/arch/arm/plat-pxa/include/plat/sdhci.h +++ /dev/null @@ -1,35 +0,0 @@ -/* linux/arch/arm/plat-pxa/include/plat/sdhci.h - * - * Copyright 2010 Marvell - * Zhangfei Gao <zhangfei.gao@marvell.com> - * - * PXA Platform - SDHCI platform data definitions - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. - */ - -#ifndef __PLAT_PXA_SDHCI_H -#define __PLAT_PXA_SDHCI_H - -/* pxa specific flag */ -/* Require clock free running */ -#define PXA_FLAG_DISABLE_CLOCK_GATING (1<<0) - -/* Board design supports 8-bit data on SD/SDIO BUS */ -#define PXA_FLAG_SD_8_BIT_CAPABLE_SLOT (1<<2) - -/* - * struct pxa_sdhci_platdata() - Platform device data for PXA SDHCI - * @max_speed: the maximum speed supported - * @quirks: quirks of specific device - * @flags: flags for platform requirement - */ -struct sdhci_pxa_platdata { - unsigned int max_speed; - unsigned int quirks; - unsigned int flags; -}; - -#endif /* __PLAT_PXA_SDHCI_H */ |