aboutsummaryrefslogtreecommitdiffstats
path: root/arch/x86/pci/k8-bus_64.c
diff options
context:
space:
mode:
Diffstat (limited to 'arch/x86/pci/k8-bus_64.c')
-rw-r--r--arch/x86/pci/k8-bus_64.c575
1 files changed, 514 insertions, 61 deletions
diff --git a/arch/x86/pci/k8-bus_64.c b/arch/x86/pci/k8-bus_64.c
index 9cc813e..ab6d4b1 100644
--- a/arch/x86/pci/k8-bus_64.c
+++ b/arch/x86/pci/k8-bus_64.c
@@ -1,83 +1,536 @@
#include <linux/init.h>
#include <linux/pci.h>
+#include <asm/pci-direct.h>
#include <asm/mpspec.h>
#include <linux/cpumask.h>
+#include <linux/topology.h>
/*
* This discovers the pcibus <-> node mapping on AMD K8.
- *
- * RED-PEN need to call this again on PCI hotplug
- * RED-PEN empty cpus get reported wrong
+ * also get peer root bus resource for io,mmio
*/
-#define NODE_ID_REGISTER 0x60
-#define NODE_ID(dword) (dword & 0x07)
-#define LDT_BUS_NUMBER_REGISTER_0 0x94
-#define LDT_BUS_NUMBER_REGISTER_1 0xB4
-#define LDT_BUS_NUMBER_REGISTER_2 0xD4
-#define NR_LDT_BUS_NUMBER_REGISTERS 3
-#define SECONDARY_LDT_BUS_NUMBER(dword) ((dword >> 8) & 0xFF)
-#define SUBORDINATE_LDT_BUS_NUMBER(dword) ((dword >> 16) & 0xFF)
-#define PCI_DEVICE_ID_K8HTCONFIG 0x1100
+
+/*
+ * sub bus (transparent) will use entres from 3 to store extra from root,
+ * so need to make sure have enought slot there, increase PCI_BUS_NUM_RESOURCES?
+ */
+#define RES_NUM 16
+struct pci_root_info {
+ char name[12];
+ unsigned int res_num;
+ struct resource res[RES_NUM];
+ int bus_min;
+ int bus_max;
+ int node;
+ int link;
+};
+
+/* 4 at this time, it may become to 32 */
+#define PCI_ROOT_NR 4
+static int pci_root_num;
+static struct pci_root_info pci_root_info[PCI_ROOT_NR];
+
+#ifdef CONFIG_NUMA
+
+#define BUS_NR 256
+
+static int mp_bus_to_node[BUS_NR];
+
+void set_mp_bus_to_node(int busnum, int node)
+{
+ if (busnum >= 0 && busnum < BUS_NR)
+ mp_bus_to_node[busnum] = node;
+}
+
+int get_mp_bus_to_node(int busnum)
+{
+ int node = -1;
+
+ if (busnum < 0 || busnum > (BUS_NR - 1))
+ return node;
+
+ node = mp_bus_to_node[busnum];
+
+ /*
+ * let numa_node_id to decide it later in dma_alloc_pages
+ * if there is no ram on that node
+ */
+ if (node != -1 && !node_online(node))
+ node = -1;
+
+ return node;
+}
+#endif
+
+void set_pci_bus_resources_arch_default(struct pci_bus *b)
+{
+ int i;
+ int j;
+ struct pci_root_info *info;
+
+ /* if only one root bus, don't need to anything */
+ if (pci_root_num < 2)
+ return;
+
+ for (i = 0; i < pci_root_num; i++) {
+ if (pci_root_info[i].bus_min == b->number)
+ break;
+ }
+
+ if (i == pci_root_num)
+ return;
+
+ info = &pci_root_info[i];
+ for (j = 0; j < info->res_num; j++) {
+ struct resource *res;
+ struct resource *root;
+
+ res = &info->res[j];
+ b->resource[j] = res;
+ if (res->flags & IORESOURCE_IO)
+ root = &ioport_resource;
+ else
+ root = &iomem_resource;
+ insert_resource(root, res);
+ }
+}
+
+#define RANGE_NUM 16
+
+struct res_range {
+ size_t start;
+ size_t end;
+};
+
+static void __init update_range(struct res_range *range, size_t start,
+ size_t end)
+{
+ int i;
+ int j;
+
+ for (j = 0; j < RANGE_NUM; j++) {
+ if (!range[j].end)
+ continue;
+
+ if (start <= range[j].start && end >= range[j].end) {
+ range[j].start = 0;
+ range[j].end = 0;
+ continue;
+ }
+
+ if (start <= range[j].start && end < range[j].end && range[j].start < end + 1) {
+ range[j].start = end + 1;
+ continue;
+ }
+
+
+ if (start > range[j].start && end >= range[j].end && range[j].end > start - 1) {
+ range[j].end = start - 1;
+ continue;
+ }
+
+ if (start > range[j].start && end < range[j].end) {
+ /* find the new spare */
+ for (i = 0; i < RANGE_NUM; i++) {
+ if (range[i].end == 0)
+ break;
+ }
+ if (i < RANGE_NUM) {
+ range[i].end = range[j].end;
+ range[i].start = end + 1;
+ } else {
+ printk(KERN_ERR "run of slot in ranges\n");
+ }
+ range[j].end = start - 1;
+ continue;
+ }
+ }
+}
+
+static void __init update_res(struct pci_root_info *info, size_t start,
+ size_t end, unsigned long flags, int merge)
+{
+ int i;
+ struct resource *res;
+
+ if (!merge)
+ goto addit;
+
+ /* try to merge it with old one */
+ for (i = 0; i < info->res_num; i++) {
+ size_t final_start, final_end;
+ size_t common_start, common_end;
+
+ res = &info->res[i];
+ if (res->flags != flags)
+ continue;
+
+ common_start = max((size_t)res->start, start);
+ common_end = min((size_t)res->end, end);
+ if (common_start > common_end + 1)
+ continue;
+
+ final_start = min((size_t)res->start, start);
+ final_end = max((size_t)res->end, end);
+
+ res->start = final_start;
+ res->end = final_end;
+ return;
+ }
+
+addit:
+
+ /* need to add that */
+ if (info->res_num >= RES_NUM)
+ return;
+
+ res = &info->res[info->res_num];
+ res->name = info->name;
+ res->flags = flags;
+ res->start = start;
+ res->end = end;
+ res->child = NULL;
+ info->res_num++;
+}
+
+struct pci_hostbridge_probe {
+ u32 bus;
+ u32 slot;
+ u32 vendor;
+ u32 device;
+};
+
+static struct pci_hostbridge_probe pci_probes[] __initdata = {
+ { 0, 0x18, PCI_VENDOR_ID_AMD, 0x1100 },
+ { 0, 0x18, PCI_VENDOR_ID_AMD, 0x1200 },
+ { 0xff, 0, PCI_VENDOR_ID_AMD, 0x1200 },
+ { 0, 0x18, PCI_VENDOR_ID_AMD, 0x1300 },
+};
+
+static u64 __initdata fam10h_mmconf_start;
+static u64 __initdata fam10h_mmconf_end;
+static void __init get_pci_mmcfg_amd_fam10h_range(void)
+{
+ u32 address;
+ u64 base, msr;
+ unsigned segn_busn_bits;
+
+ /* assume all cpus from fam10h have mmconf */
+ if (boot_cpu_data.x86 < 0x10)
+ return;
+
+ address = MSR_FAM10H_MMIO_CONF_BASE;
+ rdmsrl(address, msr);
+
+ /* mmconfig is not enable */
+ if (!(msr & FAM10H_MMIO_CONF_ENABLE))
+ return;
+
+ base = msr & (FAM10H_MMIO_CONF_BASE_MASK<<FAM10H_MMIO_CONF_BASE_SHIFT);
+
+ segn_busn_bits = (msr >> FAM10H_MMIO_CONF_BUSRANGE_SHIFT) &
+ FAM10H_MMIO_CONF_BUSRANGE_MASK;
+
+ fam10h_mmconf_start = base;
+ fam10h_mmconf_end = base + (1ULL<<(segn_busn_bits + 20)) - 1;
+}
/**
- * fill_mp_bus_to_cpumask()
+ * early_fill_mp_bus_to_node()
+ * called before pcibios_scan_root and pci_scan_bus
* fills the mp_bus_to_cpumask array based according to the LDT Bus Number
* Registers found in the K8 northbridge
*/
-__init static int
-fill_mp_bus_to_cpumask(void)
+static int __init early_fill_mp_bus_info(void)
{
- struct pci_dev *nb_dev = NULL;
- int i, j;
- u32 ldtbus, nid;
- static int lbnr[3] = {
- LDT_BUS_NUMBER_REGISTER_0,
- LDT_BUS_NUMBER_REGISTER_1,
- LDT_BUS_NUMBER_REGISTER_2
- };
-
- while ((nb_dev = pci_get_device(PCI_VENDOR_ID_AMD,
- PCI_DEVICE_ID_K8HTCONFIG, nb_dev))) {
- pci_read_config_dword(nb_dev, NODE_ID_REGISTER, &nid);
-
- for (i = 0; i < NR_LDT_BUS_NUMBER_REGISTERS; i++) {
- pci_read_config_dword(nb_dev, lbnr[i], &ldtbus);
- /*
- * if there are no busses hanging off of the current
- * ldt link then both the secondary and subordinate
- * bus number fields are set to 0.
- *
- * RED-PEN
- * This is slightly broken because it assumes
- * HT node IDs == Linux node ids, which is not always
- * true. However it is probably mostly true.
- */
- if (!(SECONDARY_LDT_BUS_NUMBER(ldtbus) == 0
- && SUBORDINATE_LDT_BUS_NUMBER(ldtbus) == 0)) {
- for (j = SECONDARY_LDT_BUS_NUMBER(ldtbus);
- j <= SUBORDINATE_LDT_BUS_NUMBER(ldtbus);
- j++) {
- struct pci_bus *bus;
- struct pci_sysdata *sd;
-
- long node = NODE_ID(nid);
- /* Algorithm a bit dumb, but
- it shouldn't matter here */
- bus = pci_find_bus(0, j);
- if (!bus)
- continue;
- if (!node_online(node))
- node = 0;
-
- sd = bus->sysdata;
- sd->node = node;
- }
+ int i;
+ int j;
+ unsigned bus;
+ unsigned slot;
+ int found;
+ int node;
+ int link;
+ int def_node;
+ int def_link;
+ struct pci_root_info *info;
+ u32 reg;
+ struct resource *res;
+ size_t start;
+ size_t end;
+ struct res_range range[RANGE_NUM];
+ u64 val;
+ u32 address;
+
+#ifdef CONFIG_NUMA
+ for (i = 0; i < BUS_NR; i++)
+ mp_bus_to_node[i] = -1;
+#endif
+
+ if (!early_pci_allowed())
+ return -1;
+
+ found = 0;
+ for (i = 0; i < ARRAY_SIZE(pci_probes); i++) {
+ u32 id;
+ u16 device;
+ u16 vendor;
+
+ bus = pci_probes[i].bus;
+ slot = pci_probes[i].slot;
+ id = read_pci_config(bus, slot, 0, PCI_VENDOR_ID);
+
+ vendor = id & 0xffff;
+ device = (id>>16) & 0xffff;
+ if (pci_probes[i].vendor == vendor &&
+ pci_probes[i].device == device) {
+ found = 1;
+ break;
+ }
+ }
+
+ if (!found)
+ return 0;
+
+ pci_root_num = 0;
+ for (i = 0; i < 4; i++) {
+ int min_bus;
+ int max_bus;
+ reg = read_pci_config(bus, slot, 1, 0xe0 + (i << 2));
+
+ /* Check if that register is enabled for bus range */
+ if ((reg & 7) != 3)
+ continue;
+
+ min_bus = (reg >> 16) & 0xff;
+ max_bus = (reg >> 24) & 0xff;
+ node = (reg >> 4) & 0x07;
+#ifdef CONFIG_NUMA
+ for (j = min_bus; j <= max_bus; j++)
+ mp_bus_to_node[j] = (unsigned char) node;
+#endif
+ link = (reg >> 8) & 0x03;
+
+ info = &pci_root_info[pci_root_num];
+ info->bus_min = min_bus;
+ info->bus_max = max_bus;
+ info->node = node;
+ info->link = link;
+ sprintf(info->name, "PCI Bus #%02x", min_bus);
+ pci_root_num++;
+ }
+
+ /* get the default node and link for left over res */
+ reg = read_pci_config(bus, slot, 0, 0x60);
+ def_node = (reg >> 8) & 0x07;
+ reg = read_pci_config(bus, slot, 0, 0x64);
+ def_link = (reg >> 8) & 0x03;
+
+ memset(range, 0, sizeof(range));
+ range[0].end = 0xffff;
+ /* io port resource */
+ for (i = 0; i < 4; i++) {
+ reg = read_pci_config(bus, slot, 1, 0xc0 + (i << 3));
+ if (!(reg & 3))
+ continue;
+
+ start = reg & 0xfff000;
+ reg = read_pci_config(bus, slot, 1, 0xc4 + (i << 3));
+ node = reg & 0x07;
+ link = (reg >> 4) & 0x03;
+ end = (reg & 0xfff000) | 0xfff;
+
+ /* find the position */
+ for (j = 0; j < pci_root_num; j++) {
+ info = &pci_root_info[j];
+ if (info->node == node && info->link == link)
+ break;
+ }
+ if (j == pci_root_num)
+ continue; /* not found */
+
+ info = &pci_root_info[j];
+ printk(KERN_DEBUG "node %d link %d: io port [%llx, %llx]\n",
+ node, link, (u64)start, (u64)end);
+
+ /* kernel only handle 16 bit only */
+ if (end > 0xffff)
+ end = 0xffff;
+ update_res(info, start, end, IORESOURCE_IO, 1);
+ update_range(range, start, end);
+ }
+ /* add left over io port range to def node/link, [0, 0xffff] */
+ /* find the position */
+ for (j = 0; j < pci_root_num; j++) {
+ info = &pci_root_info[j];
+ if (info->node == def_node && info->link == def_link)
+ break;
+ }
+ if (j < pci_root_num) {
+ info = &pci_root_info[j];
+ for (i = 0; i < RANGE_NUM; i++) {
+ if (!range[i].end)
+ continue;
+
+ update_res(info, range[i].start, range[i].end,
+ IORESOURCE_IO, 1);
+ }
+ }
+
+ memset(range, 0, sizeof(range));
+ /* 0xfd00000000-0xffffffffff for HT */
+ range[0].end = (0xfdULL<<32) - 1;
+
+ /* need to take out [0, TOM) for RAM*/
+ address = MSR_K8_TOP_MEM1;
+ rdmsrl(address, val);
+ end = (val & 0xffffff8000000ULL);
+ printk(KERN_INFO "TOM: %016lx aka %ldM\n", end, end>>20);
+ if (end < (1ULL<<32))
+ update_range(range, 0, end - 1);
+
+ /* get mmconfig */
+ get_pci_mmcfg_amd_fam10h_range();
+ /* need to take out mmconf range */
+ if (fam10h_mmconf_end) {
+ printk(KERN_DEBUG "Fam 10h mmconf [%llx, %llx]\n", fam10h_mmconf_start, fam10h_mmconf_end);
+ update_range(range, fam10h_mmconf_start, fam10h_mmconf_end);
+ }
+
+ /* mmio resource */
+ for (i = 0; i < 8; i++) {
+ reg = read_pci_config(bus, slot, 1, 0x80 + (i << 3));
+ if (!(reg & 3))
+ continue;
+
+ start = reg & 0xffffff00; /* 39:16 on 31:8*/
+ start <<= 8;
+ reg = read_pci_config(bus, slot, 1, 0x84 + (i << 3));
+ node = reg & 0x07;
+ link = (reg >> 4) & 0x03;
+ end = (reg & 0xffffff00);
+ end <<= 8;
+ end |= 0xffff;
+
+ /* find the position */
+ for (j = 0; j < pci_root_num; j++) {
+ info = &pci_root_info[j];
+ if (info->node == node && info->link == link)
+ break;
+ }
+ if (j == pci_root_num)
+ continue; /* not found */
+
+ info = &pci_root_info[j];
+
+ printk(KERN_DEBUG "node %d link %d: mmio [%llx, %llx]",
+ node, link, (u64)start, (u64)end);
+ /*
+ * some sick allocation would have range overlap with fam10h
+ * mmconf range, so need to update start and end.
+ */
+ if (fam10h_mmconf_end) {
+ int changed = 0;
+ u64 endx = 0;
+ if (start >= fam10h_mmconf_start &&
+ start <= fam10h_mmconf_end) {
+ start = fam10h_mmconf_end + 1;
+ changed = 1;
+ }
+
+ if (end >= fam10h_mmconf_start &&
+ end <= fam10h_mmconf_end) {
+ end = fam10h_mmconf_start - 1;
+ changed = 1;
+ }
+
+ if (start < fam10h_mmconf_start &&
+ end > fam10h_mmconf_end) {
+ /* we got a hole */
+ endx = fam10h_mmconf_start - 1;
+ update_res(info, start, endx, IORESOURCE_MEM, 0);
+ update_range(range, start, endx);
+ printk(KERN_CONT " ==> [%llx, %llx]", (u64)start, endx);
+ start = fam10h_mmconf_end + 1;
+ changed = 1;
+ }
+ if (changed) {
+ if (start <= end) {
+ printk(KERN_CONT " %s [%llx, %llx]", endx?"and":"==>", (u64)start, (u64)end);
+ } else {
+ printk(KERN_CONT "%s\n", endx?"":" ==> none");
+ continue;
+ }
}
}
+
+ update_res(info, start, end, IORESOURCE_MEM, 1);
+ update_range(range, start, end);
+ printk(KERN_CONT "\n");
+ }
+
+ /* need to take out [4G, TOM2) for RAM*/
+ /* SYS_CFG */
+ address = MSR_K8_SYSCFG;
+ rdmsrl(address, val);
+ /* TOP_MEM2 is enabled? */
+ if (val & (1<<21)) {
+ /* TOP_MEM2 */
+ address = MSR_K8_TOP_MEM2;
+ rdmsrl(address, val);
+ end = (val & 0xffffff8000000ULL);
+ printk(KERN_INFO "TOM2: %016lx aka %ldM\n", end, end>>20);
+ update_range(range, 1ULL<<32, end - 1);
+ }
+
+ /*
+ * add left over mmio range to def node/link ?
+ * that is tricky, just record range in from start_min to 4G
+ */
+ for (j = 0; j < pci_root_num; j++) {
+ info = &pci_root_info[j];
+ if (info->node == def_node && info->link == def_link)
+ break;
+ }
+ if (j < pci_root_num) {
+ info = &pci_root_info[j];
+
+ for (i = 0; i < RANGE_NUM; i++) {
+ if (!range[i].end)
+ continue;
+
+ update_res(info, range[i].start, range[i].end,
+ IORESOURCE_MEM, 1);
+ }
+ }
+
+#ifdef CONFIG_NUMA
+ for (i = 0; i < BUS_NR; i++) {
+ node = mp_bus_to_node[i];
+ if (node >= 0)
+ printk(KERN_DEBUG "bus: %02x to node: %02x\n", i, node);
+ }
+#endif
+
+ for (i = 0; i < pci_root_num; i++) {
+ int res_num;
+ int busnum;
+
+ info = &pci_root_info[i];
+ res_num = info->res_num;
+ busnum = info->bus_min;
+ printk(KERN_DEBUG "bus: [%02x,%02x] on node %x link %x\n",
+ info->bus_min, info->bus_max, info->node, info->link);
+ for (j = 0; j < res_num; j++) {
+ res = &info->res[j];
+ printk(KERN_DEBUG "bus: %02x index %x %s: [%llx, %llx]\n",
+ busnum, j,
+ (res->flags & IORESOURCE_IO)?"io port":"mmio",
+ res->start, res->end);
+ }
}
return 0;
}
-fs_initcall(fill_mp_bus_to_cpumask);
+postcore_initcall(early_fill_mp_bus_info);