aboutsummaryrefslogtreecommitdiffstats
path: root/drivers/gpu/drm/i915/i915_reg.h
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/gpu/drm/i915/i915_reg.h')
-rw-r--r--drivers/gpu/drm/i915/i915_reg.h335
1 files changed, 211 insertions, 124 deletions
diff --git a/drivers/gpu/drm/i915/i915_reg.h b/drivers/gpu/drm/i915/i915_reg.h
index 4f5e155..25ed911 100644
--- a/drivers/gpu/drm/i915/i915_reg.h
+++ b/drivers/gpu/drm/i915/i915_reg.h
@@ -25,52 +25,16 @@
#ifndef _I915_REG_H_
#define _I915_REG_H_
+#define _PIPE(pipe, a, b) ((a) + (pipe)*((b)-(a)))
+
/*
* The Bridge device's PCI config space has information about the
* fb aperture size and the amount of pre-reserved memory.
+ * This is all handled in the intel-gtt.ko module. i915.ko only
+ * cares about the vga bit for the vga rbiter.
*/
#define INTEL_GMCH_CTRL 0x52
#define INTEL_GMCH_VGA_DISABLE (1 << 1)
-#define INTEL_GMCH_ENABLED 0x4
-#define INTEL_GMCH_MEM_MASK 0x1
-#define INTEL_GMCH_MEM_64M 0x1
-#define INTEL_GMCH_MEM_128M 0
-
-#define INTEL_GMCH_GMS_MASK (0xf << 4)
-#define INTEL_855_GMCH_GMS_DISABLED (0x0 << 4)
-#define INTEL_855_GMCH_GMS_STOLEN_1M (0x1 << 4)
-#define INTEL_855_GMCH_GMS_STOLEN_4M (0x2 << 4)
-#define INTEL_855_GMCH_GMS_STOLEN_8M (0x3 << 4)
-#define INTEL_855_GMCH_GMS_STOLEN_16M (0x4 << 4)
-#define INTEL_855_GMCH_GMS_STOLEN_32M (0x5 << 4)
-
-#define INTEL_915G_GMCH_GMS_STOLEN_48M (0x6 << 4)
-#define INTEL_915G_GMCH_GMS_STOLEN_64M (0x7 << 4)
-#define INTEL_GMCH_GMS_STOLEN_128M (0x8 << 4)
-#define INTEL_GMCH_GMS_STOLEN_256M (0x9 << 4)
-#define INTEL_GMCH_GMS_STOLEN_96M (0xa << 4)
-#define INTEL_GMCH_GMS_STOLEN_160M (0xb << 4)
-#define INTEL_GMCH_GMS_STOLEN_224M (0xc << 4)
-#define INTEL_GMCH_GMS_STOLEN_352M (0xd << 4)
-
-#define SNB_GMCH_CTRL 0x50
-#define SNB_GMCH_GMS_STOLEN_MASK 0xF8
-#define SNB_GMCH_GMS_STOLEN_32M (1 << 3)
-#define SNB_GMCH_GMS_STOLEN_64M (2 << 3)
-#define SNB_GMCH_GMS_STOLEN_96M (3 << 3)
-#define SNB_GMCH_GMS_STOLEN_128M (4 << 3)
-#define SNB_GMCH_GMS_STOLEN_160M (5 << 3)
-#define SNB_GMCH_GMS_STOLEN_192M (6 << 3)
-#define SNB_GMCH_GMS_STOLEN_224M (7 << 3)
-#define SNB_GMCH_GMS_STOLEN_256M (8 << 3)
-#define SNB_GMCH_GMS_STOLEN_288M (9 << 3)
-#define SNB_GMCH_GMS_STOLEN_320M (0xa << 3)
-#define SNB_GMCH_GMS_STOLEN_352M (0xb << 3)
-#define SNB_GMCH_GMS_STOLEN_384M (0xc << 3)
-#define SNB_GMCH_GMS_STOLEN_416M (0xd << 3)
-#define SNB_GMCH_GMS_STOLEN_448M (0xe << 3)
-#define SNB_GMCH_GMS_STOLEN_480M (0xf << 3)
-#define SNB_GMCH_GMS_STOLEN_512M (0x10 << 3)
/* PCI config space */
@@ -106,10 +70,13 @@
#define I915_GC_RENDER_CLOCK_200_MHZ (1 << 0)
#define I915_GC_RENDER_CLOCK_333_MHZ (4 << 0)
#define LBB 0xf4
-#define GDRST 0xc0
-#define GDRST_FULL (0<<2)
-#define GDRST_RENDER (1<<2)
-#define GDRST_MEDIA (3<<2)
+
+/* Graphics reset regs */
+#define I965_GDRST 0xc0 /* PCI config register */
+#define ILK_GDSR 0x2ca4 /* MCHBAR offset */
+#define GRDOM_FULL (0<<2)
+#define GRDOM_RENDER (1<<2)
+#define GRDOM_MEDIA (3<<2)
/* VGA stuff */
@@ -192,11 +159,11 @@
#define MI_STORE_DWORD_INDEX MI_INSTR(0x21, 1)
#define MI_STORE_DWORD_INDEX_SHIFT 2
#define MI_LOAD_REGISTER_IMM MI_INSTR(0x22, 1)
+#define MI_FLUSH_DW MI_INSTR(0x26, 2) /* for GEN6 */
#define MI_BATCH_BUFFER MI_INSTR(0x30, 1)
#define MI_BATCH_NON_SECURE (1)
#define MI_BATCH_NON_SECURE_I965 (1<<8)
#define MI_BATCH_BUFFER_START MI_INSTR(0x31, 0)
-
/*
* 3D instructions used by the kernel
*/
@@ -249,6 +216,16 @@
#define PIPE_CONTROL_GLOBAL_GTT (1<<2) /* in addr dword */
#define PIPE_CONTROL_STALL_EN (1<<1) /* in addr word, Ironlake+ only */
+
+/*
+ * Reset registers
+ */
+#define DEBUG_RESET_I830 0x6070
+#define DEBUG_RESET_FULL (1<<7)
+#define DEBUG_RESET_RENDER (1<<8)
+#define DEBUG_RESET_DISPLAY (1<<9)
+
+
/*
* Fence registers
*/
@@ -283,6 +260,17 @@
#define PRB0_HEAD 0x02034
#define PRB0_START 0x02038
#define PRB0_CTL 0x0203c
+#define RENDER_RING_BASE 0x02000
+#define BSD_RING_BASE 0x04000
+#define GEN6_BSD_RING_BASE 0x12000
+#define BLT_RING_BASE 0x22000
+#define RING_TAIL(base) ((base)+0x30)
+#define RING_HEAD(base) ((base)+0x34)
+#define RING_START(base) ((base)+0x38)
+#define RING_CTL(base) ((base)+0x3c)
+#define RING_HWS_PGA(base) ((base)+0x80)
+#define RING_HWS_PGA_GEN6(base) ((base)+0x2080)
+#define RING_ACTHD(base) ((base)+0x74)
#define TAIL_ADDR 0x001FFFF8
#define HEAD_WRAP_COUNT 0xFFE00000
#define HEAD_WRAP_ONE 0x00200000
@@ -295,6 +283,8 @@
#define RING_VALID_MASK 0x00000001
#define RING_VALID 0x00000001
#define RING_INVALID 0x00000000
+#define RING_WAIT_I8XX (1<<0) /* gen2, PRBx_HEAD */
+#define RING_WAIT (1<<11) /* gen3+, PRBx_CTL */
#define PRB1_TAIL 0x02040 /* 915+ only */
#define PRB1_HEAD 0x02044 /* 915+ only */
#define PRB1_START 0x02048 /* 915+ only */
@@ -306,7 +296,6 @@
#define INSTDONE1 0x0207c /* 965+ only */
#define ACTHD_I965 0x02074
#define HWS_PGA 0x02080
-#define HWS_PGA_GEN6 0x04080
#define HWS_ADDRESS_MASK 0xfffff000
#define HWS_START_ADDRESS_SHIFT 4
#define PWRCTXA 0x2088 /* 965GM+ only */
@@ -464,17 +453,17 @@
#define GEN6_BLITTER_COMMAND_PARSER_MASTER_ERROR (1 << 25)
#define GEN6_BLITTER_SYNC_STATUS (1 << 24)
#define GEN6_BLITTER_USER_INTERRUPT (1 << 22)
-/*
- * BSD (bit stream decoder instruction and interrupt control register defines
- * (G4X and Ironlake only)
- */
-#define BSD_RING_TAIL 0x04030
-#define BSD_RING_HEAD 0x04034
-#define BSD_RING_START 0x04038
-#define BSD_RING_CTL 0x0403c
-#define BSD_RING_ACTHD 0x04074
-#define BSD_HWS_PGA 0x04080
+#define GEN6_BSD_SLEEP_PSMI_CONTROL 0x12050
+#define GEN6_BSD_SLEEP_PSMI_CONTROL_RC_ILDL_MESSAGE_MODIFY_MASK (1 << 16)
+#define GEN6_BSD_SLEEP_PSMI_CONTROL_RC_ILDL_MESSAGE_DISABLE (1 << 0)
+#define GEN6_BSD_SLEEP_PSMI_CONTROL_RC_ILDL_MESSAGE_ENABLE 0
+#define GEN6_BSD_SLEEP_PSMI_CONTROL_IDLE_INDICATOR (1 << 3)
+
+#define GEN6_BSD_IMR 0x120a8
+#define GEN6_BSD_IMR_USER_INTERRUPT (1 << 12)
+
+#define GEN6_BSD_RNCID 0x12198
/*
* Framebuffer compression (915+ only)
@@ -579,12 +568,51 @@
# define GPIO_DATA_VAL_IN (1 << 12)
# define GPIO_DATA_PULLUP_DISABLE (1 << 13)
-#define GMBUS0 0x5100
-#define GMBUS1 0x5104
-#define GMBUS2 0x5108
-#define GMBUS3 0x510c
-#define GMBUS4 0x5110
-#define GMBUS5 0x5120
+#define GMBUS0 0x5100 /* clock/port select */
+#define GMBUS_RATE_100KHZ (0<<8)
+#define GMBUS_RATE_50KHZ (1<<8)
+#define GMBUS_RATE_400KHZ (2<<8) /* reserved on Pineview */
+#define GMBUS_RATE_1MHZ (3<<8) /* reserved on Pineview */
+#define GMBUS_HOLD_EXT (1<<7) /* 300ns hold time, rsvd on Pineview */
+#define GMBUS_PORT_DISABLED 0
+#define GMBUS_PORT_SSC 1
+#define GMBUS_PORT_VGADDC 2
+#define GMBUS_PORT_PANEL 3
+#define GMBUS_PORT_DPC 4 /* HDMIC */
+#define GMBUS_PORT_DPB 5 /* SDVO, HDMIB */
+ /* 6 reserved */
+#define GMBUS_PORT_DPD 7 /* HDMID */
+#define GMBUS_NUM_PORTS 8
+#define GMBUS1 0x5104 /* command/status */
+#define GMBUS_SW_CLR_INT (1<<31)
+#define GMBUS_SW_RDY (1<<30)
+#define GMBUS_ENT (1<<29) /* enable timeout */
+#define GMBUS_CYCLE_NONE (0<<25)
+#define GMBUS_CYCLE_WAIT (1<<25)
+#define GMBUS_CYCLE_INDEX (2<<25)
+#define GMBUS_CYCLE_STOP (4<<25)
+#define GMBUS_BYTE_COUNT_SHIFT 16
+#define GMBUS_SLAVE_INDEX_SHIFT 8
+#define GMBUS_SLAVE_ADDR_SHIFT 1
+#define GMBUS_SLAVE_READ (1<<0)
+#define GMBUS_SLAVE_WRITE (0<<0)
+#define GMBUS2 0x5108 /* status */
+#define GMBUS_INUSE (1<<15)
+#define GMBUS_HW_WAIT_PHASE (1<<14)
+#define GMBUS_STALL_TIMEOUT (1<<13)
+#define GMBUS_INT (1<<12)
+#define GMBUS_HW_RDY (1<<11)
+#define GMBUS_SATOER (1<<10)
+#define GMBUS_ACTIVE (1<<9)
+#define GMBUS3 0x510c /* data buffer bytes 3-0 */
+#define GMBUS4 0x5110 /* interrupt mask (Pineview+) */
+#define GMBUS_SLAVE_TIMEOUT_EN (1<<4)
+#define GMBUS_NAK_EN (1<<3)
+#define GMBUS_IDLE_EN (1<<2)
+#define GMBUS_HW_WAIT_EN (1<<1)
+#define GMBUS_HW_RDY_EN (1<<0)
+#define GMBUS5 0x5120 /* byte index */
+#define GMBUS_2BYTE_INDEX_EN (1<<31)
/*
* Clock control & power management
@@ -603,6 +631,7 @@
#define VGA1_PD_P1_MASK (0x1f << 8)
#define DPLL_A 0x06014
#define DPLL_B 0x06018
+#define DPLL(pipe) _PIPE(pipe, DPLL_A, DPLL_B)
#define DPLL_VCO_ENABLE (1 << 31)
#define DPLL_DVO_HIGH_SPEED (1 << 30)
#define DPLL_SYNCLOCK_ENABLE (1 << 29)
@@ -633,31 +662,6 @@
#define LVDS 0x61180
#define LVDS_ON (1<<31)
-#define ADPA 0x61100
-#define ADPA_DPMS_MASK (~(3<<10))
-#define ADPA_DPMS_ON (0<<10)
-#define ADPA_DPMS_SUSPEND (1<<10)
-#define ADPA_DPMS_STANDBY (2<<10)
-#define ADPA_DPMS_OFF (3<<10)
-
-#define RING_TAIL 0x00
-#define TAIL_ADDR 0x001FFFF8
-#define RING_HEAD 0x04
-#define HEAD_WRAP_COUNT 0xFFE00000
-#define HEAD_WRAP_ONE 0x00200000
-#define HEAD_ADDR 0x001FFFFC
-#define RING_START 0x08
-#define START_ADDR 0xFFFFF000
-#define RING_LEN 0x0C
-#define RING_NR_PAGES 0x001FF000
-#define RING_REPORT_MASK 0x00000006
-#define RING_REPORT_64K 0x00000002
-#define RING_REPORT_128K 0x00000004
-#define RING_NO_REPORT 0x00000000
-#define RING_VALID_MASK 0x00000001
-#define RING_VALID 0x00000001
-#define RING_INVALID 0x00000000
-
/* Scratch pad debug 0 reg:
*/
#define DPLL_FPA01_P1_POST_DIV_MASK_I830 0x001f0000
@@ -736,10 +740,13 @@
#define DPLL_MD_VGA_UDI_MULTIPLIER_MASK 0x0000003f
#define DPLL_MD_VGA_UDI_MULTIPLIER_SHIFT 0
#define DPLL_B_MD 0x06020 /* 965+ only */
+#define DPLL_MD(pipe) _PIPE(pipe, DPLL_A_MD, DPLL_B_MD)
#define FPA0 0x06040
#define FPA1 0x06044
#define FPB0 0x06048
#define FPB1 0x0604c
+#define FP0(pipe) _PIPE(pipe, FPA0, FPB0)
+#define FP1(pipe) _PIPE(pipe, FPA1, FPB1)
#define FP_N_DIV_MASK 0x003f0000
#define FP_N_PINEVIEW_DIV_MASK 0x00ff0000
#define FP_N_DIV_SHIFT 16
@@ -760,6 +767,7 @@
#define DPLLA_TEST_M_BYPASS (1 << 2)
#define DPLLA_INPUT_BUFFER_ENABLE (1 << 0)
#define D_STATE 0x6104
+#define DSTATE_GFX_RESET_I830 (1<<6)
#define DSTATE_PLL_D3_OFF (1<<3)
#define DSTATE_GFX_CLOCK_GATING (1<<1)
#define DSTATE_DOT_CLOCK_GATING (1<<0)
@@ -926,6 +934,8 @@
#define CLKCFG_MEM_800 (3 << 4)
#define CLKCFG_MEM_MASK (7 << 4)
+#define TSC1 0x11001
+#define TSE (1<<0)
#define TR1 0x11006
#define TSFS 0x11020
#define TSFS_SLOPE_MASK 0x0000ff00
@@ -1070,6 +1080,8 @@
#define MEMSTAT_SRC_CTL_STDBY 3
#define RCPREVBSYTUPAVG 0x113b8
#define RCPREVBSYTDNAVG 0x113bc
+#define PMMISC 0x11214
+#define MCPPCE_EN (1<<0) /* enable PM_MSG from PCH->MPC */
#define SDEW 0x1124c
#define CSIEW0 0x11250
#define CSIEW1 0x11254
@@ -1150,6 +1162,15 @@
#define PIPEBSRC 0x6101c
#define BCLRPAT_B 0x61020
+#define HTOTAL(pipe) _PIPE(pipe, HTOTAL_A, HTOTAL_B)
+#define HBLANK(pipe) _PIPE(pipe, HBLANK_A, HBLANK_B)
+#define HSYNC(pipe) _PIPE(pipe, HSYNC_A, HSYNC_B)
+#define VTOTAL(pipe) _PIPE(pipe, VTOTAL_A, VTOTAL_B)
+#define VBLANK(pipe) _PIPE(pipe, VBLANK_A, VBLANK_B)
+#define VSYNC(pipe) _PIPE(pipe, VSYNC_A, VSYNC_B)
+#define PIPESRC(pipe) _PIPE(pipe, PIPEASRC, PIPEBSRC)
+#define BCLRPAT(pipe) _PIPE(pipe, BCLRPAT_A, BCLRPAT_B)
+
/* VGA port control */
#define ADPA 0x61100
#define ADPA_DAC_ENABLE (1<<31)
@@ -1173,6 +1194,7 @@
#define ADPA_DPMS_STANDBY (2<<10)
#define ADPA_DPMS_OFF (3<<10)
+
/* Hotplug control (945+ only) */
#define PORT_HOTPLUG_EN 0x61110
#define HDMIB_HOTPLUG_INT_EN (1 << 29)
@@ -1331,6 +1353,22 @@
#define LVDS_B0B3_POWER_DOWN (0 << 2)
#define LVDS_B0B3_POWER_UP (3 << 2)
+/* Video Data Island Packet control */
+#define VIDEO_DIP_DATA 0x61178
+#define VIDEO_DIP_CTL 0x61170
+#define VIDEO_DIP_ENABLE (1 << 31)
+#define VIDEO_DIP_PORT_B (1 << 29)
+#define VIDEO_DIP_PORT_C (2 << 29)
+#define VIDEO_DIP_ENABLE_AVI (1 << 21)
+#define VIDEO_DIP_ENABLE_VENDOR (2 << 21)
+#define VIDEO_DIP_ENABLE_SPD (8 << 21)
+#define VIDEO_DIP_SELECT_AVI (0 << 19)
+#define VIDEO_DIP_SELECT_VENDOR (1 << 19)
+#define VIDEO_DIP_SELECT_SPD (3 << 19)
+#define VIDEO_DIP_FREQ_ONCE (0 << 16)
+#define VIDEO_DIP_FREQ_VSYNC (1 << 16)
+#define VIDEO_DIP_FREQ_2VSYNC (2 << 16)
+
/* Panel power sequencing */
#define PP_STATUS 0x61200
#define PP_ON (1 << 31)
@@ -1346,6 +1384,9 @@
#define PP_SEQUENCE_ON (1 << 28)
#define PP_SEQUENCE_OFF (2 << 28)
#define PP_SEQUENCE_MASK 0x30000000
+#define PP_CYCLE_DELAY_ACTIVE (1 << 27)
+#define PP_SEQUENCE_STATE_ON_IDLE (1 << 3)
+#define PP_SEQUENCE_STATE_MASK 0x0000000f
#define PP_CONTROL 0x61204
#define POWER_TARGET_ON (1 << 0)
#define PP_ON_DELAYS 0x61208
@@ -1481,6 +1522,7 @@
# define TV_TEST_MODE_MASK (7 << 0)
#define TV_DAC 0x68004
+# define TV_DAC_SAVE 0x00ffff00
/**
* Reports that DAC state change logic has reported change (RO).
*
@@ -2075,29 +2117,35 @@
/* Display & cursor control */
-/* dithering flag on Ironlake */
-#define PIPE_ENABLE_DITHER (1 << 4)
-#define PIPE_DITHER_TYPE_MASK (3 << 2)
-#define PIPE_DITHER_TYPE_SPATIAL (0 << 2)
-#define PIPE_DITHER_TYPE_ST01 (1 << 2)
/* Pipe A */
#define PIPEADSL 0x70000
-#define DSL_LINEMASK 0x00000fff
+#define DSL_LINEMASK 0x00000fff
#define PIPEACONF 0x70008
-#define PIPEACONF_ENABLE (1<<31)
-#define PIPEACONF_DISABLE 0
-#define PIPEACONF_DOUBLE_WIDE (1<<30)
+#define PIPECONF_ENABLE (1<<31)
+#define PIPECONF_DISABLE 0
+#define PIPECONF_DOUBLE_WIDE (1<<30)
#define I965_PIPECONF_ACTIVE (1<<30)
-#define PIPEACONF_SINGLE_WIDE 0
-#define PIPEACONF_PIPE_UNLOCKED 0
-#define PIPEACONF_PIPE_LOCKED (1<<25)
-#define PIPEACONF_PALETTE 0
-#define PIPEACONF_GAMMA (1<<24)
+#define PIPECONF_SINGLE_WIDE 0
+#define PIPECONF_PIPE_UNLOCKED 0
+#define PIPECONF_PIPE_LOCKED (1<<25)
+#define PIPECONF_PALETTE 0
+#define PIPECONF_GAMMA (1<<24)
#define PIPECONF_FORCE_BORDER (1<<25)
#define PIPECONF_PROGRESSIVE (0 << 21)
#define PIPECONF_INTERLACE_W_FIELD_INDICATION (6 << 21)
#define PIPECONF_INTERLACE_FIELD_0_ONLY (7 << 21)
#define PIPECONF_CXSR_DOWNCLOCK (1<<16)
+#define PIPECONF_BPP_MASK (0x000000e0)
+#define PIPECONF_BPP_8 (0<<5)
+#define PIPECONF_BPP_10 (1<<5)
+#define PIPECONF_BPP_6 (2<<5)
+#define PIPECONF_BPP_12 (3<<5)
+#define PIPECONF_DITHER_EN (1<<4)
+#define PIPECONF_DITHER_TYPE_MASK (0x0000000c)
+#define PIPECONF_DITHER_TYPE_SP (0<<2)
+#define PIPECONF_DITHER_TYPE_ST1 (1<<2)
+#define PIPECONF_DITHER_TYPE_ST2 (2<<2)
+#define PIPECONF_DITHER_TYPE_TEMP (3<<2)
#define PIPEASTAT 0x70024
#define PIPE_FIFO_UNDERRUN_STATUS (1UL<<31)
#define PIPE_CRC_ERROR_ENABLE (1UL<<29)
@@ -2128,12 +2176,15 @@
#define PIPE_START_VBLANK_INTERRUPT_STATUS (1UL<<2) /* 965 or later */
#define PIPE_VBLANK_INTERRUPT_STATUS (1UL<<1)
#define PIPE_OVERLAY_UPDATED_STATUS (1UL<<0)
-#define PIPE_BPC_MASK (7 << 5) /* Ironlake */
+#define PIPE_BPC_MASK (7 << 5) /* Ironlake */
#define PIPE_8BPC (0 << 5)
#define PIPE_10BPC (1 << 5)
#define PIPE_6BPC (2 << 5)
#define PIPE_12BPC (3 << 5)
+#define PIPECONF(pipe) _PIPE(pipe, PIPEACONF, PIPEBCONF)
+#define PIPEDSL(pipe) _PIPE(pipe, PIPEADSL, PIPEBDSL)
+
#define DSPARB 0x70030
#define DSPARB_CSTART_MASK (0x7f << 7)
#define DSPARB_CSTART_SHIFT 7
@@ -2206,8 +2257,8 @@
#define WM1_LP_SR_EN (1<<31)
#define WM1_LP_LATENCY_SHIFT 24
#define WM1_LP_LATENCY_MASK (0x7f<<24)
-#define WM1_LP_FBC_LP1_MASK (0xf<<20)
-#define WM1_LP_FBC_LP1_SHIFT 20
+#define WM1_LP_FBC_MASK (0xf<<20)
+#define WM1_LP_FBC_SHIFT 20
#define WM1_LP_SR_MASK (0x1ff<<8)
#define WM1_LP_SR_SHIFT 8
#define WM1_LP_CURSOR_MASK (0x3f)
@@ -2333,6 +2384,14 @@
#define DSPASURF 0x7019C /* 965+ only */
#define DSPATILEOFF 0x701A4 /* 965+ only */
+#define DSPCNTR(plane) _PIPE(plane, DSPACNTR, DSPBCNTR)
+#define DSPADDR(plane) _PIPE(plane, DSPAADDR, DSPBADDR)
+#define DSPSTRIDE(plane) _PIPE(plane, DSPASTRIDE, DSPBSTRIDE)
+#define DSPPOS(plane) _PIPE(plane, DSPAPOS, DSPBPOS)
+#define DSPSIZE(plane) _PIPE(plane, DSPASIZE, DSPBSIZE)
+#define DSPSURF(plane) _PIPE(plane, DSPASURF, DSPBSURF)
+#define DSPTILEOFF(plane) _PIPE(plane, DSPATILEOFF, DSPBTILEOFF)
+
/* VBIOS flags */
#define SWF00 0x71410
#define SWF01 0x71414
@@ -2397,6 +2456,7 @@
#define RR_HW_HIGH_POWER_FRAMES_MASK 0xff00
#define FDI_PLL_BIOS_0 0x46000
+#define FDI_PLL_FB_CLOCK_MASK 0xff
#define FDI_PLL_BIOS_1 0x46004
#define FDI_PLL_BIOS_2 0x46008
#define DISPLAY_PORT_PLL_BIOS_0 0x4600c
@@ -2420,46 +2480,47 @@
#define PIPEA_DATA_M1 0x60030
#define TU_SIZE(x) (((x)-1) << 25) /* default size 64 */
#define TU_SIZE_MASK 0x7e000000
-#define PIPEA_DATA_M1_OFFSET 0
+#define PIPE_DATA_M1_OFFSET 0
#define PIPEA_DATA_N1 0x60034
-#define PIPEA_DATA_N1_OFFSET 0
+#define PIPE_DATA_N1_OFFSET 0
#define PIPEA_DATA_M2 0x60038
-#define PIPEA_DATA_M2_OFFSET 0
+#define PIPE_DATA_M2_OFFSET 0
#define PIPEA_DATA_N2 0x6003c
-#define PIPEA_DATA_N2_OFFSET 0
+#define PIPE_DATA_N2_OFFSET 0
#define PIPEA_LINK_M1 0x60040
-#define PIPEA_LINK_M1_OFFSET 0
+#define PIPE_LINK_M1_OFFSET 0
#define PIPEA_LINK_N1 0x60044
-#define PIPEA_LINK_N1_OFFSET 0
+#define PIPE_LINK_N1_OFFSET 0
#define PIPEA_LINK_M2 0x60048
-#define PIPEA_LINK_M2_OFFSET 0
+#define PIPE_LINK_M2_OFFSET 0
#define PIPEA_LINK_N2 0x6004c
-#define PIPEA_LINK_N2_OFFSET 0
+#define PIPE_LINK_N2_OFFSET 0
/* PIPEB timing regs are same start from 0x61000 */
#define PIPEB_DATA_M1 0x61030
-#define PIPEB_DATA_M1_OFFSET 0
#define PIPEB_DATA_N1 0x61034
-#define PIPEB_DATA_N1_OFFSET 0
#define PIPEB_DATA_M2 0x61038
-#define PIPEB_DATA_M2_OFFSET 0
#define PIPEB_DATA_N2 0x6103c
-#define PIPEB_DATA_N2_OFFSET 0
#define PIPEB_LINK_M1 0x61040
-#define PIPEB_LINK_M1_OFFSET 0
#define PIPEB_LINK_N1 0x61044
-#define PIPEB_LINK_N1_OFFSET 0
#define PIPEB_LINK_M2 0x61048
-#define PIPEB_LINK_M2_OFFSET 0
#define PIPEB_LINK_N2 0x6104c
-#define PIPEB_LINK_N2_OFFSET 0
+
+#define PIPE_DATA_M1(pipe) _PIPE(pipe, PIPEA_DATA_M1, PIPEB_DATA_M1)
+#define PIPE_DATA_N1(pipe) _PIPE(pipe, PIPEA_DATA_N1, PIPEB_DATA_N1)
+#define PIPE_DATA_M2(pipe) _PIPE(pipe, PIPEA_DATA_M2, PIPEB_DATA_M2)
+#define PIPE_DATA_N2(pipe) _PIPE(pipe, PIPEA_DATA_N2, PIPEB_DATA_N2)
+#define PIPE_LINK_M1(pipe) _PIPE(pipe, PIPEA_LINK_M1, PIPEB_LINK_M1)
+#define PIPE_LINK_N1(pipe) _PIPE(pipe, PIPEA_LINK_N1, PIPEB_LINK_N1)
+#define PIPE_LINK_M2(pipe) _PIPE(pipe, PIPEA_LINK_M2, PIPEB_LINK_M2)
+#define PIPE_LINK_N2(pipe) _PIPE(pipe, PIPEA_LINK_N2, PIPEB_LINK_N2)
/* CPU panel fitter */
#define PFA_CTL_1 0x68080
@@ -2516,7 +2577,8 @@
#define GT_SYNC_STATUS (1 << 2)
#define GT_USER_INTERRUPT (1 << 0)
#define GT_BSD_USER_INTERRUPT (1 << 5)
-
+#define GT_GEN6_BSD_USER_INTERRUPT (1 << 12)
+#define GT_BLT_USER_INTERRUPT (1 << 22)
#define GTISR 0x44010
#define GTIMR 0x44014
@@ -2551,6 +2613,10 @@
#define SDE_PORTD_HOTPLUG_CPT (1 << 23)
#define SDE_PORTC_HOTPLUG_CPT (1 << 22)
#define SDE_PORTB_HOTPLUG_CPT (1 << 21)
+#define SDE_HOTPLUG_MASK_CPT (SDE_CRT_HOTPLUG_CPT | \
+ SDE_PORTD_HOTPLUG_CPT | \
+ SDE_PORTC_HOTPLUG_CPT | \
+ SDE_PORTB_HOTPLUG_CPT)
#define SDEISR 0xc4000
#define SDEIMR 0xc4004
@@ -2600,11 +2666,14 @@
#define PCH_DPLL_A 0xc6014
#define PCH_DPLL_B 0xc6018
+#define PCH_DPLL(pipe) _PIPE(pipe, PCH_DPLL_A, PCH_DPLL_B)
#define PCH_FPA0 0xc6040
#define PCH_FPA1 0xc6044
#define PCH_FPB0 0xc6048
#define PCH_FPB1 0xc604c
+#define PCH_FP0(pipe) _PIPE(pipe, PCH_FPA0, PCH_FPB0)
+#define PCH_FP1(pipe) _PIPE(pipe, PCH_FPA1, PCH_FPB1)
#define PCH_DPLL_TEST 0xc606c
@@ -2690,6 +2759,13 @@
#define TRANS_VBLANK_B 0xe1010
#define TRANS_VSYNC_B 0xe1014
+#define TRANS_HTOTAL(pipe) _PIPE(pipe, TRANS_HTOTAL_A, TRANS_HTOTAL_B)
+#define TRANS_HBLANK(pipe) _PIPE(pipe, TRANS_HBLANK_A, TRANS_HBLANK_B)
+#define TRANS_HSYNC(pipe) _PIPE(pipe, TRANS_HSYNC_A, TRANS_HSYNC_B)
+#define TRANS_VTOTAL(pipe) _PIPE(pipe, TRANS_VTOTAL_A, TRANS_VTOTAL_B)
+#define TRANS_VBLANK(pipe) _PIPE(pipe, TRANS_VBLANK_A, TRANS_VBLANK_B)
+#define TRANS_VSYNC(pipe) _PIPE(pipe, TRANS_VSYNC_A, TRANS_VSYNC_B)
+
#define TRANSB_DATA_M1 0xe1030
#define TRANSB_DATA_N1 0xe1034
#define TRANSB_DATA_M2 0xe1038
@@ -2701,6 +2777,7 @@
#define TRANSACONF 0xf0008
#define TRANSBCONF 0xf1008
+#define TRANSCONF(plane) _PIPE(plane, TRANSACONF, TRANSBCONF)
#define TRANS_DISABLE (0<<31)
#define TRANS_ENABLE (1<<31)
#define TRANS_STATE_MASK (1<<30)
@@ -2721,10 +2798,15 @@
#define FDI_RXA_CHICKEN 0xc200c
#define FDI_RXB_CHICKEN 0xc2010
#define FDI_RX_PHASE_SYNC_POINTER_ENABLE (1)
+#define FDI_RX_CHICKEN(pipe) _PIPE(pipe, FDI_RXA_CHICKEN, FDI_RXB_CHICKEN)
+
+#define SOUTH_DSPCLK_GATE_D 0xc2020
+#define PCH_DPLSUNIT_CLOCK_GATE_DISABLE (1<<29)
/* CPU: FDI_TX */
#define FDI_TXA_CTL 0x60100
#define FDI_TXB_CTL 0x61100
+#define FDI_TX_CTL(pipe) _PIPE(pipe, FDI_TXA_CTL, FDI_TXB_CTL)
#define FDI_TX_DISABLE (0<<31)
#define FDI_TX_ENABLE (1<<31)
#define FDI_LINK_TRAIN_PATTERN_1 (0<<28)
@@ -2766,8 +2848,8 @@
/* FDI_RX, FDI_X is hard-wired to Transcoder_X */
#define FDI_RXA_CTL 0xf000c
#define FDI_RXB_CTL 0xf100c
+#define FDI_RX_CTL(pipe) _PIPE(pipe, FDI_RXA_CTL, FDI_RXB_CTL)
#define FDI_RX_ENABLE (1<<31)
-#define FDI_RX_DISABLE (0<<31)
/* train, dp width same as FDI_TX */
#define FDI_DP_PORT_WIDTH_X8 (7<<19)
#define FDI_8BPC (0<<16)
@@ -2782,8 +2864,7 @@
#define FDI_FS_ERR_REPORT_ENABLE (1<<9)
#define FDI_FE_ERR_REPORT_ENABLE (1<<8)
#define FDI_RX_ENHANCE_FRAME_ENABLE (1<<6)
-#define FDI_SEL_RAWCLK (0<<4)
-#define FDI_SEL_PCDCLK (1<<4)
+#define FDI_PCDCLK (1<<4)
/* CPT */
#define FDI_AUTO_TRAINING (1<<10)
#define FDI_LINK_TRAIN_PATTERN_1_CPT (0<<8)
@@ -2798,6 +2879,9 @@
#define FDI_RXA_TUSIZE2 0xf0038
#define FDI_RXB_TUSIZE1 0xf1030
#define FDI_RXB_TUSIZE2 0xf1038
+#define FDI_RX_MISC(pipe) _PIPE(pipe, FDI_RXA_MISC, FDI_RXB_MISC)
+#define FDI_RX_TUSIZE1(pipe) _PIPE(pipe, FDI_RXA_TUSIZE1, FDI_RXB_TUSIZE1)
+#define FDI_RX_TUSIZE2(pipe) _PIPE(pipe, FDI_RXA_TUSIZE2, FDI_RXB_TUSIZE2)
/* FDI_RX interrupt register format */
#define FDI_RX_INTER_LANE_ALIGN (1<<10)
@@ -2816,6 +2900,8 @@
#define FDI_RXA_IMR 0xf0018
#define FDI_RXB_IIR 0xf1014
#define FDI_RXB_IMR 0xf1018
+#define FDI_RX_IIR(pipe) _PIPE(pipe, FDI_RXA_IIR, FDI_RXB_IIR)
+#define FDI_RX_IMR(pipe) _PIPE(pipe, FDI_RXA_IMR, FDI_RXB_IMR)
#define FDI_PLL_CTL_1 0xfe000
#define FDI_PLL_CTL_2 0xfe004
@@ -2935,6 +3021,7 @@
#define TRANS_DP_CTL_A 0xe0300
#define TRANS_DP_CTL_B 0xe1300
#define TRANS_DP_CTL_C 0xe2300
+#define TRANS_DP_CTL(pipe) (TRANS_DP_CTL_A + (pipe) * 0x01000)
#define TRANS_DP_OUTPUT_ENABLE (1<<31)
#define TRANS_DP_PORT_SEL_B (0<<29)
#define TRANS_DP_PORT_SEL_C (1<<29)