diff options
Diffstat (limited to 'drivers/staging/gma500/psb_intel_sdvo_regs.h')
| -rw-r--r-- | drivers/staging/gma500/psb_intel_sdvo_regs.h | 338 |
1 files changed, 338 insertions, 0 deletions
diff --git a/drivers/staging/gma500/psb_intel_sdvo_regs.h b/drivers/staging/gma500/psb_intel_sdvo_regs.h new file mode 100644 index 0000000..a1d1475 --- /dev/null +++ b/drivers/staging/gma500/psb_intel_sdvo_regs.h @@ -0,0 +1,338 @@ +/* + * SDVO command definitions and structures. + * + * Copyright (c) 2008, Intel Corporation + * + * This program is free software; you can redistribute it and/or modify it + * under the terms and conditions of the GNU General Public License, + * version 2, as published by the Free Software Foundation. + * + * This program is distributed in the hope it will be useful, but WITHOUT + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for + * more details. + * + * You should have received a copy of the GNU General Public License along with + * this program; if not, write to the Free Software Foundation, Inc., + * 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA. + * + * Authors: + * Eric Anholt <eric@anholt.net> + */ + +#define SDVO_OUTPUT_FIRST (0) +#define SDVO_OUTPUT_TMDS0 (1 << 0) +#define SDVO_OUTPUT_RGB0 (1 << 1) +#define SDVO_OUTPUT_CVBS0 (1 << 2) +#define SDVO_OUTPUT_SVID0 (1 << 3) +#define SDVO_OUTPUT_YPRPB0 (1 << 4) +#define SDVO_OUTPUT_SCART0 (1 << 5) +#define SDVO_OUTPUT_LVDS0 (1 << 6) +#define SDVO_OUTPUT_TMDS1 (1 << 8) +#define SDVO_OUTPUT_RGB1 (1 << 9) +#define SDVO_OUTPUT_CVBS1 (1 << 10) +#define SDVO_OUTPUT_SVID1 (1 << 11) +#define SDVO_OUTPUT_YPRPB1 (1 << 12) +#define SDVO_OUTPUT_SCART1 (1 << 13) +#define SDVO_OUTPUT_LVDS1 (1 << 14) +#define SDVO_OUTPUT_LAST (14) + +struct psb_intel_sdvo_caps { + u8 vendor_id; + u8 device_id; + u8 device_rev_id; + u8 sdvo_version_major; + u8 sdvo_version_minor; + unsigned int sdvo_inputs_mask:2; + unsigned int smooth_scaling:1; + unsigned int sharp_scaling:1; + unsigned int up_scaling:1; + unsigned int down_scaling:1; + unsigned int stall_support:1; + unsigned int pad:1; + u16 output_flags; +} __attribute__ ((packed)); + +/** This matches the EDID DTD structure, more or less */ +struct psb_intel_sdvo_dtd { + struct { + u16 clock; /**< pixel clock, in 10kHz units */ + u8 h_active; /**< lower 8 bits (pixels) */ + u8 h_blank; /**< lower 8 bits (pixels) */ + u8 h_high; /**< upper 4 bits each h_active, h_blank */ + u8 v_active; /**< lower 8 bits (lines) */ + u8 v_blank; /**< lower 8 bits (lines) */ + u8 v_high; /**< upper 4 bits each v_active, v_blank */ + } part1; + + struct { + u8 h_sync_off; + /**< lower 8 bits, from hblank start */ + u8 h_sync_width;/**< lower 8 bits (pixels) */ + /** lower 4 bits each vsync offset, vsync width */ + u8 v_sync_off_width; + /** + * 2 high bits of hsync offset, 2 high bits of hsync width, + * bits 4-5 of vsync offset, and 2 high bits of vsync width. + */ + u8 sync_off_width_high; + u8 dtd_flags; + u8 sdvo_flags; + /** bits 6-7 of vsync offset at bits 6-7 */ + u8 v_sync_off_high; + u8 reserved; + } part2; +} __attribute__ ((packed)); + +struct psb_intel_sdvo_pixel_clock_range { + u16 min; /**< pixel clock, in 10kHz units */ + u16 max; /**< pixel clock, in 10kHz units */ +} __attribute__ ((packed)); + +struct psb_intel_sdvo_preferred_input_timing_args { + u16 clock; + u16 width; + u16 height; +} __attribute__ ((packed)); + +/* I2C registers for SDVO */ +#define SDVO_I2C_ARG_0 0x07 +#define SDVO_I2C_ARG_1 0x06 +#define SDVO_I2C_ARG_2 0x05 +#define SDVO_I2C_ARG_3 0x04 +#define SDVO_I2C_ARG_4 0x03 +#define SDVO_I2C_ARG_5 0x02 +#define SDVO_I2C_ARG_6 0x01 +#define SDVO_I2C_ARG_7 0x00 +#define SDVO_I2C_OPCODE 0x08 +#define SDVO_I2C_CMD_STATUS 0x09 +#define SDVO_I2C_RETURN_0 0x0a +#define SDVO_I2C_RETURN_1 0x0b +#define SDVO_I2C_RETURN_2 0x0c +#define SDVO_I2C_RETURN_3 0x0d +#define SDVO_I2C_RETURN_4 0x0e +#define SDVO_I2C_RETURN_5 0x0f +#define SDVO_I2C_RETURN_6 0x10 +#define SDVO_I2C_RETURN_7 0x11 +#define SDVO_I2C_VENDOR_BEGIN 0x20 + +/* Status results */ +#define SDVO_CMD_STATUS_POWER_ON 0x0 +#define SDVO_CMD_STATUS_SUCCESS 0x1 +#define SDVO_CMD_STATUS_NOTSUPP 0x2 +#define SDVO_CMD_STATUS_INVALID_ARG 0x3 +#define SDVO_CMD_STATUS_PENDING 0x4 +#define SDVO_CMD_STATUS_TARGET_NOT_SPECIFIED 0x5 +#define SDVO_CMD_STATUS_SCALING_NOT_SUPP 0x6 + +/* SDVO commands, argument/result registers */ + +#define SDVO_CMD_RESET 0x01 + +/** Returns a struct psb_intel_sdvo_caps */ +#define SDVO_CMD_GET_DEVICE_CAPS 0x02 + +#define SDVO_CMD_GET_FIRMWARE_REV 0x86 +# define SDVO_DEVICE_FIRMWARE_MINOR SDVO_I2C_RETURN_0 +# define SDVO_DEVICE_FIRMWARE_MAJOR SDVO_I2C_RETURN_1 +# define SDVO_DEVICE_FIRMWARE_PATCH SDVO_I2C_RETURN_2 + +/** + * Reports which inputs are trained (managed to sync). + * + * Devices must have trained within 2 vsyncs of a mode change. + */ +#define SDVO_CMD_GET_TRAINED_INPUTS 0x03 +struct psb_intel_sdvo_get_trained_inputs_response { + unsigned int input0_trained:1; + unsigned int input1_trained:1; + unsigned int pad:6; +} __attribute__ ((packed)); + +/** Returns a struct psb_intel_sdvo_output_flags of active outputs. */ +#define SDVO_CMD_GET_ACTIVE_OUTPUTS 0x04 + +/** + * Sets the current set of active outputs. + * + * Takes a struct psb_intel_sdvo_output_flags. + * Must be preceded by a SET_IN_OUT_MAP + * on multi-output devices. + */ +#define SDVO_CMD_SET_ACTIVE_OUTPUTS 0x05 + +/** + * Returns the current mapping of SDVO inputs to outputs on the device. + * + * Returns two struct psb_intel_sdvo_output_flags structures. + */ +#define SDVO_CMD_GET_IN_OUT_MAP 0x06 + +/** + * Sets the current mapping of SDVO inputs to outputs on the device. + * + * Takes two struct i380_sdvo_output_flags structures. + */ +#define SDVO_CMD_SET_IN_OUT_MAP 0x07 + +/** + * Returns a struct psb_intel_sdvo_output_flags of attached displays. + */ +#define SDVO_CMD_GET_ATTACHED_DISPLAYS 0x0b + +/** + * Returns a struct psb_intel_sdvo_ouptut_flags of displays supporting hot plugging. + */ +#define SDVO_CMD_GET_HOT_PLUG_SUPPORT 0x0c + +/** + * Takes a struct psb_intel_sdvo_output_flags. + */ +#define SDVO_CMD_SET_ACTIVE_HOT_PLUG 0x0d + +/** + * Returns a struct psb_intel_sdvo_output_flags of displays with hot plug + * interrupts enabled. + */ +#define SDVO_CMD_GET_ACTIVE_HOT_PLUG 0x0e + +#define SDVO_CMD_GET_INTERRUPT_EVENT_SOURCE 0x0f +struct psb_intel_sdvo_get_interrupt_event_source_response { + u16 interrupt_status; + unsigned int ambient_light_interrupt:1; + unsigned int pad:7; +} __attribute__ ((packed)); + +/** + * Selects which input is affected by future input commands. + * + * Commands affected include SET_INPUT_TIMINGS_PART[12], + * GET_INPUT_TIMINGS_PART[12], GET_PREFERRED_INPUT_TIMINGS_PART[12], + * GET_INPUT_PIXEL_CLOCK_RANGE, and CREATE_PREFERRED_INPUT_TIMINGS. + */ +#define SDVO_CMD_SET_TARGET_INPUT 0x10 +struct psb_intel_sdvo_set_target_input_args { + unsigned int target_1:1; + unsigned int pad:7; +} __attribute__ ((packed)); + +/** + * Takes a struct psb_intel_sdvo_output_flags of which outputs are targetted by + * future output commands. + * + * Affected commands inclue SET_OUTPUT_TIMINGS_PART[12], + * GET_OUTPUT_TIMINGS_PART[12], and GET_OUTPUT_PIXEL_CLOCK_RANGE. + */ +#define SDVO_CMD_SET_TARGET_OUTPUT 0x11 + +#define SDVO_CMD_GET_INPUT_TIMINGS_PART1 0x12 +#define SDVO_CMD_GET_INPUT_TIMINGS_PART2 0x13 +#define SDVO_CMD_SET_INPUT_TIMINGS_PART1 0x14 +#define SDVO_CMD_SET_INPUT_TIMINGS_PART2 0x15 +#define SDVO_CMD_SET_OUTPUT_TIMINGS_PART1 0x16 +#define SDVO_CMD_SET_OUTPUT_TIMINGS_PART2 0x17 +#define SDVO_CMD_GET_OUTPUT_TIMINGS_PART1 0x18 +#define SDVO_CMD_GET_OUTPUT_TIMINGS_PART2 0x19 +/* Part 1 */ +# define SDVO_DTD_CLOCK_LOW SDVO_I2C_ARG_0 +# define SDVO_DTD_CLOCK_HIGH SDVO_I2C_ARG_1 +# define SDVO_DTD_H_ACTIVE SDVO_I2C_ARG_2 +# define SDVO_DTD_H_BLANK SDVO_I2C_ARG_3 +# define SDVO_DTD_H_HIGH SDVO_I2C_ARG_4 +# define SDVO_DTD_V_ACTIVE SDVO_I2C_ARG_5 +# define SDVO_DTD_V_BLANK SDVO_I2C_ARG_6 +# define SDVO_DTD_V_HIGH SDVO_I2C_ARG_7 +/* Part 2 */ +# define SDVO_DTD_HSYNC_OFF SDVO_I2C_ARG_0 +# define SDVO_DTD_HSYNC_WIDTH SDVO_I2C_ARG_1 +# define SDVO_DTD_VSYNC_OFF_WIDTH SDVO_I2C_ARG_2 +# define SDVO_DTD_SYNC_OFF_WIDTH_HIGH SDVO_I2C_ARG_3 +# define SDVO_DTD_DTD_FLAGS SDVO_I2C_ARG_4 +# define SDVO_DTD_DTD_FLAG_INTERLACED (1 << 7) +# define SDVO_DTD_DTD_FLAG_STEREO_MASK (3 << 5) +# define SDVO_DTD_DTD_FLAG_INPUT_MASK (3 << 3) +# define SDVO_DTD_DTD_FLAG_SYNC_MASK (3 << 1) +# define SDVO_DTD_SDVO_FLAS SDVO_I2C_ARG_5 +# define SDVO_DTD_SDVO_FLAG_STALL (1 << 7) +# define SDVO_DTD_SDVO_FLAG_CENTERED (0 << 6) +# define SDVO_DTD_SDVO_FLAG_UPPER_LEFT (1 << 6) +# define SDVO_DTD_SDVO_FLAG_SCALING_MASK (3 << 4) +# define SDVO_DTD_SDVO_FLAG_SCALING_NONE (0 << 4) +# define SDVO_DTD_SDVO_FLAG_SCALING_SHARP (1 << 4) +# define SDVO_DTD_SDVO_FLAG_SCALING_SMOOTH (2 << 4) +# define SDVO_DTD_VSYNC_OFF_HIGH SDVO_I2C_ARG_6 + +/** + * Generates a DTD based on the given width, height, and flags. + * + * This will be supported by any device supporting scaling or interlaced + * modes. + */ +#define SDVO_CMD_CREATE_PREFERRED_INPUT_TIMING 0x1a +# define SDVO_PREFERRED_INPUT_TIMING_CLOCK_LOW SDVO_I2C_ARG_0 +# define SDVO_PREFERRED_INPUT_TIMING_CLOCK_HIGH SDVO_I2C_ARG_1 +# define SDVO_PREFERRED_INPUT_TIMING_WIDTH_LOW SDVO_I2C_ARG_2 +# define SDVO_PREFERRED_INPUT_TIMING_WIDTH_HIGH SDVO_I2C_ARG_3 +# define SDVO_PREFERRED_INPUT_TIMING_HEIGHT_LOW SDVO_I2C_ARG_4 +# define SDVO_PREFERRED_INPUT_TIMING_HEIGHT_HIGH SDVO_I2C_ARG_5 +# define SDVO_PREFERRED_INPUT_TIMING_FLAGS SDVO_I2C_ARG_6 +# define SDVO_PREFERRED_INPUT_TIMING_FLAGS_INTERLACED (1 << 0) +# define SDVO_PREFERRED_INPUT_TIMING_FLAGS_SCALED (1 << 1) + +#define SDVO_CMD_GET_PREFERRED_INPUT_TIMING_PART1 0x1b +#define SDVO_CMD_GET_PREFERRED_INPUT_TIMING_PART2 0x1c + +/** Returns a struct psb_intel_sdvo_pixel_clock_range */ +#define SDVO_CMD_GET_INPUT_PIXEL_CLOCK_RANGE 0x1d +/** Returns a struct psb_intel_sdvo_pixel_clock_range */ +#define SDVO_CMD_GET_OUTPUT_PIXEL_CLOCK_RANGE 0x1e + +/** Returns a byte bitfield containing SDVO_CLOCK_RATE_MULT_* flags */ +#define SDVO_CMD_GET_SUPPORTED_CLOCK_RATE_MULTS 0x1f + +/** Returns a byte containing a SDVO_CLOCK_RATE_MULT_* flag */ +#define SDVO_CMD_GET_CLOCK_RATE_MULT 0x20 +/** Takes a byte containing a SDVO_CLOCK_RATE_MULT_* flag */ +#define SDVO_CMD_SET_CLOCK_RATE_MULT 0x21 +# define SDVO_CLOCK_RATE_MULT_1X (1 << 0) +# define SDVO_CLOCK_RATE_MULT_2X (1 << 1) +# define SDVO_CLOCK_RATE_MULT_4X (1 << 3) + +#define SDVO_CMD_GET_SUPPORTED_TV_FORMATS 0x27 + +#define SDVO_CMD_GET_TV_FORMAT 0x28 + +#define SDVO_CMD_SET_TV_FORMAT 0x29 + +#define SDVO_CMD_GET_SUPPORTED_POWER_STATES 0x2a +#define SDVO_CMD_GET_ENCODER_POWER_STATE 0x2b +#define SDVO_CMD_SET_ENCODER_POWER_STATE 0x2c +# define SDVO_ENCODER_STATE_ON (1 << 0) +# define SDVO_ENCODER_STATE_STANDBY (1 << 1) +# define SDVO_ENCODER_STATE_SUSPEND (1 << 2) +# define SDVO_ENCODER_STATE_OFF (1 << 3) + +#define SDVO_CMD_SET_TV_RESOLUTION_SUPPORT 0x93 + +#define SDVO_CMD_SET_CONTROL_BUS_SWITCH 0x7a +# define SDVO_CONTROL_BUS_PROM 0x0 +# define SDVO_CONTROL_BUS_DDC1 0x1 +# define SDVO_CONTROL_BUS_DDC2 0x2 +# define SDVO_CONTROL_BUS_DDC3 0x3 + +/* SDVO Bus & SDVO Inputs wiring details*/ +/* Bit 0: Is SDVOB connected to In0 (1 = yes, 0 = no*/ +/* Bit 1: Is SDVOB connected to In1 (1 = yes, 0 = no*/ +/* Bit 2: Is SDVOC connected to In0 (1 = yes, 0 = no*/ +/* Bit 3: Is SDVOC connected to In1 (1 = yes, 0 = no*/ +#define SDVOB_IN0 0x01 +#define SDVOB_IN1 0x02 +#define SDVOC_IN0 0x04 +#define SDVOC_IN1 0x08 + +#define SDVO_DEVICE_NONE 0x00 +#define SDVO_DEVICE_CRT 0x01 +#define SDVO_DEVICE_TV 0x02 +#define SDVO_DEVICE_LVDS 0x04 +#define SDVO_DEVICE_TMDS 0x08 + |