aboutsummaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
* binary_sysctl(): fix memory leakMichel Lespinasse2012-01-061-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | commit 3d3c8f93a237b64580c5c5e138edeb1377e98230 upstream. binary_sysctl() calls sysctl_getname() which allocates from names_cache slab usin __getname() The matching function to free the name is __putname(), and not putname() which should be used only to match getname() allocations. This is because when auditing is enabled, putname() calls audit_putname *instead* (not in addition) to __putname(). Then, if a syscall is in progress, audit_putname does not release the name - instead, it expects the name to get released when the syscall completes, but that will happen only if audit_getname() was called previously, i.e. if the name was allocated with getname() rather than the naked __getname(). So, __getname() followed by putname() ends up leaking memory. Signed-off-by: Michel Lespinasse <walken@google.com> Acked-by: Al Viro <viro@zeniv.linux.org.uk> Cc: Christoph Hellwig <hch@infradead.org> Cc: Eric Paris <eparis@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* percpu: fix per_cpu_ptr_to_phys() handling of non-page-aligned addressesEugene Surovegin2012-01-061-2/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | commit 9f57bd4d6dc69a4e3bf43044fa00fcd24dd363e3 upstream. per_cpu_ptr_to_phys() incorrectly rounds up its result for non-kmalloc case to the page boundary, which is bogus for any non-page-aligned address. This affects the only in-tree user of this function - sysfs handler for per-cpu 'crash_notes' physical address. The trouble is that the crash_notes per-cpu variable is not page-aligned: crash_notes = 0xc08e8ed4 PER-CPU OFFSET VALUES: CPU 0: 3711f000 CPU 1: 37129000 CPU 2: 37133000 CPU 3: 3713d000 So, the per-cpu addresses are: crash_notes on CPU 0: f7a07ed4 => phys 36b57ed4 crash_notes on CPU 1: f7a11ed4 => phys 36b4ded4 crash_notes on CPU 2: f7a1bed4 => phys 36b43ed4 crash_notes on CPU 3: f7a25ed4 => phys 36b39ed4 However, /sys/devices/system/cpu/cpu*/crash_notes says: /sys/devices/system/cpu/cpu0/crash_notes: 36b57000 /sys/devices/system/cpu/cpu1/crash_notes: 36b4d000 /sys/devices/system/cpu/cpu2/crash_notes: 36b43000 /sys/devices/system/cpu/cpu3/crash_notes: 36b39000 As you can see, all values are rounded down to a page boundary. Consequently, this is where kexec sets up the NOTE segments, and thus where the secondary kernel is looking for them. However, when the first kernel crashes, it saves the notes to the unaligned addresses, where they are not found. Fix it by adding offset_in_page() to the translated page address. -tj: Combined Eugene's and Petr's commit messages. Signed-off-by: Eugene Surovegin <ebs@ebshome.net> Signed-off-by: Tejun Heo <tj@kernel.org> Reported-by: Petr Tesarik <ptesarik@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* Input: synaptics - fix touchpad not working after S2R on Vostro V13Dmitry Torokhov2012-01-061-0/+11
| | | | | | | | | | | | | | | | | | commit 8521478f67e95ada4e87970c7b41e504c724b2cf upstream. Synaptics touchpads on several Dell laptops, particularly Vostro V13 systems, may not respond properly to PS/2 commands and queries immediately after resuming from suspend to RAM. This leads to unresponsive touchpad after suspend/resume cycle. Adding a 1-second delay after resetting the device allows touchpad to finish initializing (calibrating?) and start reacting properly. Reported-by: Daniel Manrique <daniel.manrique@canonical.com> Tested-by: Daniel Manrique <daniel.manrique@canonical.com> Signed-off-by: Dmitry Torokhov <dtor@mail.ru> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* MXC PWM: should active during DOZE/WAIT/DBG modeJason Chen2012-01-061-1/+6
| | | | | | | | | commit c0d96aed8c6dd925afe9ea35491a0cd458642a86 upstream. Signed-off-by: Jason Chen <jason.chen@linaro.org> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* ssb: fix init regression with SoCsHauke Mehrtens2012-01-061-2/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | commit 329456d1ffb416c220813725b7363cda9975c9aa upstream. This fixes a Data bus error on some SoCs. The first fix for this problem did not solve it on all devices. commit 6ae8ec27868bfdbb815287bee8146acbefaee867 Author: Rafał Miłecki <zajec5@gmail.com> Date: Tue Jul 5 17:25:32 2011 +0200 ssb: fix init regression of hostmode PCI core In ssb_pcicore_fix_sprom_core_index() the sprom on the PCI core is accessed, but the sprom only exists when the ssb bus is connected over a PCI bus to the rest of the system and not when the SSB Bus is the main system bus. SoCs sometimes have a PCI host controller and there this code will not be executed, but there are some old SoCs with an PCI controller in client mode around and ssb_pcicore_fix_sprom_core_index() should not be called on these devices too. The PCI controller on these devices are unused, but without this fix it results in an Data bus error when it gets initialized. Cc: Michael Buesch <m@bues.ch> Cc: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* block: initialize request_queue's numa node duringMike Snitzer2012-01-062-14/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | commit 5151412dd4338b273afdb107c3772528e9e67d92 upstream. struct request_queue is allocated with __GFP_ZERO so its "node" field is zero before initialization. This causes an oops if node 0 is offline in the page allocator because its zonelists are not initialized. From Dave Young's dmesg: SRAT: Node 1 PXM 2 0-d0000000 SRAT: Node 1 PXM 2 100000000-330000000 SRAT: Node 0 PXM 1 330000000-630000000 Initmem setup node 1 0000000000000000-000000000affb000 ... Built 1 zonelists in Node order, mobility grouping on. ... BUG: unable to handle kernel paging request at 0000000000001c08 IP: [<ffffffff8111c355>] __alloc_pages_nodemask+0xb5/0x870 and __alloc_pages_nodemask+0xb5 translates to a NULL pointer on zonelist->_zonerefs. The fix is to initialize q->node at the time of allocation so the correct node is passed to the slab allocator later. Since blk_init_allocated_queue_node() is no longer needed, merge it with blk_init_allocated_queue(). [rientjes@google.com: changelog, initializing q->node] Reported-by: Dave Young <dyoung@redhat.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: David Rientjes <rientjes@google.com> Tested-by: Dave Young <dyoung@redhat.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* mac80211: fix another race in aggregation startJohannes Berg2012-01-061-45/+41
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | commit 15062e6a8524f5977f2cbdf6e3eb2f144262f74e upstream. Emmanuel noticed that when mac80211 stops the queues for aggregation that can leave a packet pending. This packet will be given to the driver after the AMPDU callback, but as a non-aggregated packet which messes up the sequence number etc. I also noticed by looking at the code that if packets are being processed while we clear the WANT_START bit, they might see it cleared already and queue up on tid_tx->pending. If the driver then rejects the new aggregation session we leak the packet. Fix both of these issues by changing this code to not stop the queues at all. Instead, let packets queue up on the tid_tx->pending queue instead of letting them get to the driver, and add code to recover properly in case the driver rejects the session. (The patch looks large because it has to move two functions to before their new use.) Reported-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* SCSI: fcoe: Fix preempt count leak in fcoe_filter_frames()Thomas Gleixner2012-01-061-0/+1
| | | | | | | | | | | | commit 7e1e7ead88dff75b11b86ee0d5232c4591be1326 upstream. The error exit path leaks preempt count. Add the missing put_cpu(). Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Yi Zou <yi.zou@intel.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* SCSI: mpt2sas: _scsih_smart_predicted_fault uses GFP_KERNEL in interrupt contextAnton Blanchard2012-01-061-1/+1
| | | | | | | | | | | | commit f6a290b419a2675c4b77a6b0731cd2a64332365e upstream. _scsih_smart_predicted_fault is called in an interrupt and therefore must allocate memory using GFP_ATOMIC. Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: James Bottomley <JBottomley@Parallels.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* SCSI: zfcp: return early from slave_destroy if slave_alloc returned earlySteffen Maier2012-01-061-0/+4
| | | | | | | | | | | | | | | | | | | | | | commit 44f747fff6e9f027a4866c1a6864e26ae7c510c8 upstream. zfcp_scsi_slave_destroy erroneously always tried to finish its task even if the corresponding previous zfcp_scsi_slave_alloc returned early. This can lead to kernel page faults on accessing uninitialized fields of struct zfcp_scsi_dev in zfcp_erp_lun_shutdown_wait. Take the port field of the struct to determine if slave_alloc returned early. This zfcp bug is exposed by 4e6c82b (in turn fixing f7c9c6b to be compatible with 21208ae) which can call slave_destroy for a corresponding previous slave_alloc that did not finish. This patch is based on James Bottomley's fix suggestion in http://www.spinics.net/lists/linux-scsi/msg55449.html. Signed-off-by: Steffen Maier <maier@linux.vnet.ibm.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* cfq-iosched: fix cfq_cic_link() race confitionYasuaki Ishimatsu2012-01-061-2/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | commit 5eb46851de3904cd1be9192fdacb8d34deadc1fc upstream. cfq_cic_link() has race condition. When some processes which shared ioc issue I/O to same block device simultaneously, cfq_cic_link() returns -EEXIST sometimes. The race condition might stop I/O by following steps: step 1: Process A: Issue an I/O to /dev/sda step 2: Process A: Get an ioc (iocA here) in get_io_context() which does not linked with a cic for the device step 3: Process A: Get a new cic for the device (cicA here) in cfq_alloc_io_context() step 4: Process B: Issue an I/O to /dev/sda step 5: Process B: Get iocA in get_io_context() since process A and B share the same ioc step 6: Process B: Get a new cic for the device (cicB here) in cfq_alloc_io_context() since iocA has not been linked with a cic for the device yet step 7: Process A: Link cicA to iocA in cfq_cic_link() step 8: Process A: Dispatch I/O to driver and finish it step 9: Process B: Try to link cicB to iocA in cfq_cic_link() But it fails with showing "cfq: cic link failed!" kernel message, since iocA has already linked with cicA at step 7. step 10: Process B: Wait for finishig I/O in get_request_wait() The function does not wake up, when there is no I/O to the device. When cfq_cic_link() returns -EEXIST, it means ioc has already linked with cic. So when cfq_cic_link() return -EEXIST, retry cfq_cic_lookup(). Signed-off-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* cfq-iosched: free cic_index if blkio_alloc_blkg_stats failsmajianpeng2012-01-061-0/+5
| | | | | | | | | | | | commit 2984ff38ccf6cbc02a7a996a36c7d6f69f3c6146 upstream. If we fail allocating the blkpg stats, we free cfqd and cfgq. But we need to free the IDA cfqd->cic_index as well. Signed-off-by: majianpeng <majianpeng@gmail.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* drm/i915: prevent division by zero when asking for chipset powerEugeni Dodonov2012-01-062-0/+11
| | | | | | | | | | | | | | | | | | | | | | | | | | commit 4ed0b577457eb6aeb7cdc7e7316576e63d15abb2 upstream. This prevents an in-kernel division by zero which happens when we are asking for i915_chipset_val too quickly, or within a race condition between the power monitoring thread and userspace accesses via debugfs. The issue can be reproduced easily via the following command: while ``; do cat /sys/kernel/debug/dri/0/i915_emon_status; done This is particularly dangerous because it can be triggered by a non-privileged user by just reading the debugfs entry. This issue was also found independently by Konstantin Belousov <kostikbel@gmail.com>, who proposed a similar patch. Reported-by: Konstantin Belousov <kostikbel@gmail.com> Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org> Acked-by: Keith Packard <keithp@keithp.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com> Signed-off-by: Keith Packard <keithp@keithp.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* rtc: m41t80: Workaround broken alarm functionalityJohn Stultz2012-01-061-0/+9
| | | | | | | | | | | | | | | | | | | | | | | | commit c3b79770e51ab1fd4201f3b54edf30113b9ce74f upstream. The m41t80 driver can read and set the alarm, but it doesn't seem to have a functional alarm irq. This causes failures when the generic core sees alarm functions, but then cannot use them properly for things like UIE mode. Disabling the alarm functions allows proper error reporting, and possible fallback to emulated modes. Once someone fixes the alarm irq functionality, this can be restored. CC: Matt Turner <mattst88@gmail.com> CC: Nico Macrionitis <acrux@cruxppc.org> CC: Atsushi Nemoto <anemo@mba.ocn.ne.jp> Reported-by: Matt Turner <mattst88@gmail.com> Reported-by: Nico Macrionitis <acrux@cruxppc.org> Tested-by: Nico Macrionitis <acrux@cruxppc.org> Signed-off-by: John Stultz <john.stultz@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* ipip, sit: copy parms.name after register_netdeviceTed Feng2012-01-062-2/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | commit 72b36015ba43a3cca5303f5534d2c3e1899eae29 upstream. Same fix as 731abb9cb2 for ipip and sit tunnel. Commit 1c5cae815d removed an explicit call to dev_alloc_name in ipip_tunnel_locate and ipip6_tunnel_locate, because register_netdevice will now create a valid name, however the tunnel keeps a copy of the name in the private parms structure. Fix this by copying the name back after register_netdevice has successfully returned. This shows up if you do a simple tunnel add, followed by a tunnel show: $ sudo ip tunnel add mode ipip remote 10.2.20.211 $ ip tunnel tunl0: ip/ip remote any local any ttl inherit nopmtudisc tunl%d: ip/ip remote 10.2.20.211 local any ttl inherit $ sudo ip tunnel add mode sit remote 10.2.20.212 $ ip tunnel sit0: ipv6/ip remote any local any ttl 64 nopmtudisc 6rd-prefix 2002::/16 sit%d: ioctl 89f8 failed: No such device sit%d: ipv6/ip remote 10.2.20.212 local any ttl inherit Signed-off-by: Ted Feng <artisdom@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* ARM: OMAP: rx51: fix USBFelipe Contreras2012-01-061-1/+1
| | | | | | | | | | | | | | | | | | | | commit e5fe29c7198a1f6616286dfc8602a69da165cb3f upstream. Commit 10299e2e4e3ed3b16503d4e04edd48b33083f4e2 (ARM: RX-51: Enable isp1704 power on/off) added power management for isp1704. However, the transceiver should be powered on by default, otherwise USB doesn't work at all for networking during boot. All kernels after v3.0 are affected. Signed-off-by: Felipe Contreras <felipe.contreras@gmail.com> Reviewed-by: Sebastian Reichel <sre@debian.org> [tony@atomide.com: updated comments] Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* Linux 3.0.15Greg Kroah-Hartman2012-01-031-1/+1
|
* Revert "clockevents: Set noop handler in clockevents_exchange_device()"Linus Torvalds2012-01-031-1/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | commit 3b87487ac5008072f138953b07505a7e3493327f upstream. This reverts commit de28f25e8244c7353abed8de0c7792f5f883588c. It results in resume problems for various people. See for example http://thread.gmane.org/gmane.linux.kernel/1233033 http://thread.gmane.org/gmane.linux.kernel/1233389 http://thread.gmane.org/gmane.linux.kernel/1233159 http://thread.gmane.org/gmane.linux.kernel/1227868/focus=1230877 and the fedora and ubuntu bug reports https://bugzilla.redhat.com/show_bug.cgi?id=767248 https://bugs.launchpad.net/ubuntu/+source/linux/+bug/904569 which got bisected down to the stable version of this commit. Reported-by: Jonathan Nieder <jrnieder@gmail.com> Reported-by: Phil Miller <mille121@illinois.edu> Reported-by: Philip Langdale <philipl@overt.org> Reported-by: Tim Gardner <tim.gardner@canonical.com> Cc: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* Linux 3.0.14Greg Kroah-Hartman2011-12-211-1/+1
|
* ASoC: core: Don't schedule deferred_resume_work twiceStephen Warren2011-12-211-9/+10
| | | | | | | | | | | | | | | | | | | | | | | | | commit 82e14e8bdd88b69018fe757192b01dd98582905e upstream. For cards that have two or more DAIs, snd_soc_resume's loop over all DAIs ends up calling schedule_work(deferred_resume_work) once per DAI. Since this is the same work item each time, the 2nd and subsequent calls return 0 (work item already queued), and trigger the dev_err message below stating that a work item may have been lost. Solve this by adjusting the loop to simply calculate whether to run the resume work immediately or defer it, and then call schedule work (or not) one time based on that. Note: This has not been tested in mainline, but only in chromeos-2.6.38; mainline doesn't support suspend/resume on Tegra, nor does the mainline Tegra ASoC driver contain multiple DAIs. It has been compile-checked in mainline. Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Liam Girdwood <lrg@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* USB: option: Removing one bogus and adding some new Huawei combinationsBjørn Mork2011-12-211-1/+3
| | | | | | | | | | | | | | | | | | | | | | | | commit 02a551c9755b799579e0a093bcc99b80b4dc1453 upstream. Huawei use the product code HUAWEI_PRODUCT_E353 (0x1506) for a number of different devices, which each can appear with a number of different descriptor sets. Different types of interfaces can be identified by looking at the subclass and protocol fields Subclass 1 protocol 8 is actually the data interface of a CDC ECM set, with subclass 1 protocol 9 as the control interface. Neither support serial data communcation, and cannot therefore be supported by this driver. At the same time, add a few other sets which appear if the device is configured in "Windows mode" using this modeswitch message: 55534243000000000000000000000011060000000100000000000000000000 Signed-off-by: Bjørn Mork <bjorn@mork.no> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* usb: option: Add Huawei E398 controlling interfacesAlex Hermann2011-12-211-0/+3
| | | | | | | | | | | | | commit 414b591fd16655871e9f5592a55368b10a3ccc30 upstream. This patch adds the controlling interfaces for the Huawei E398. Thanks to Bjørn Mork <bjorn@mork.no> for extracting the interface numbers from the windows driver. Signed-off-by: Alex Hermann <alex@wenlex.nl> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* USB: cdc-acm: add IDs for Motorola H24 HSPA USB module.Krzysztof Hałasa2011-12-211-0/+10
| | | | | | | | | | | commit 6abff5dc4d5a2c90e597137ce8987e7fd439259b upstream. Add USB IDs for Motorola H24 HSPA USB module. Signed-off-by: Krzysztof Hałasa <khalasa@piap.pl> Acked-by: Oliver Neukum <oneukum@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* ibft: Fix finding IBFT ACPI table on UEFIYinghai Lu2011-12-212-26/+42
| | | | | | | | | | | | | | | | | | | | | | | | | | commit 935a9fee51c945b8942be2d7b4bae069167b4886 upstream. Found one system with UEFI/iBFT, kernel does not detect the iBFT during iscsi_ibft module loading. Root cause: on x86 (UEFI), we are calling of find_ibft_region() much earlier - specifically in setup_arch() before ACPI is enabled. Try to split acpi checking code out and call that later At that time ACPI iBFT already get permanent mapped with ioremap. So isa_virt_to_bus() will get wrong phys from right virt address. We could just skip that phys address printing. For legacy one, print the found address early. -v2: update comments and description according to Konrad. -v3: fix problem about module use case that is found by Konrad. -v4: use acpi_get_table() instead of acpi_table_parse() to handle module use case that is found by Konrad again.. Signed-off-by: Yinghai Lu <yinghai@kernel.org> Signed-off-by: Konrad Rzeszutek Wilk <konrad@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* drm/radeon/kms: add some new pci idsAlex Deucher2011-12-211-0/+10
| | | | | | | | | | | | commit cd5cfce856684e13b9b57d46b78bb827e9c4da3c upstream. Fixes: https://bugs.freedesktop.org/show_bug.cgi?id=43739 Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Dave Airlie <airlied@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* staging: r8712u: Add new USB IDLarry Finger2011-12-211-0/+1
| | | | | | | | | | | commit c7caf4d4c56aee40b995f5858ccf1c814f3d2da2 upstream. Add USB ID for Sitecom WLA-2000 v1.001 WLAN. Reported-and-tested-by: Roland Gruber <post@rolandgruber.de> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* fuse: fix fuse_retrieveMiklos Szeredi2011-12-211-1/+2
| | | | | | | | | | | | | | | | | | | commit 48706d0a91583d08c56e7ef2a7602d99c8d4133f upstream. Fix two bugs in fuse_retrieve(): - retrieving more than one page would yield repeated instances of the first page - if more than FUSE_MAX_PAGES_PER_REQ pages were requested than the request page array would overflow fuse_retrieve() was added in 2.6.36 and these bugs had been there since the beginning. Signed-off-by: Miklos Szeredi <mszeredi@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* ext4: handle EOF correctly in ext4_bio_write_page()Yongqiang Yang2011-12-211-0/+12
| | | | | | | | | | | | commit 5a0dc7365c240795bf190766eba7a27600be3b3e upstream. We need to zero out part of a page which beyond EOF before setting uptodate, otherwise, mapread or write will see non-zero data beyond EOF. Signed-off-by: Yongqiang Yang <xiaoqiangnk@gmail.com> Signed-off-by: "Theodore Ts'o" <tytso@mit.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* ext4: avoid potential hang in mpage_submit_io() when blocksize < pagesizeYongqiang Yang2011-12-211-2/+5
| | | | | | | | | | | | | | | commit 13a79a4741d37fda2fbafb953f0f301dc007928f upstream. If there is an unwritten but clean buffer in a page and there is a dirty buffer after the buffer, then mpage_submit_io does not write the dirty buffer out. As a result, da_writepages loops forever. This patch fixes the problem by checking dirty flag. Signed-off-by: Yongqiang Yang <xiaoqiangnk@gmail.com> Signed-off-by: "Theodore Ts'o" <tytso@mit.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* ext4: avoid hangs in ext4_da_should_update_i_disksize()Andrea Arcangeli2011-12-211-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | commit ea51d132dbf9b00063169c1159bee253d9649224 upstream. If the pte mapping in generic_perform_write() is unmapped between iov_iter_fault_in_readable() and iov_iter_copy_from_user_atomic(), the "copied" parameter to ->end_write can be zero. ext4 couldn't cope with it with delayed allocations enabled. This skips the i_disksize enlargement logic if copied is zero and no new data was appeneded to the inode. gdb> bt #0 0xffffffff811afe80 in ext4_da_should_update_i_disksize (file=0xffff88003f606a80, mapping=0xffff88001d3824e0, pos=0x1\ 08000, len=0x1000, copied=0x0, page=0xffffea0000d792e8, fsdata=0x0) at fs/ext4/inode.c:2467 #1 ext4_da_write_end (file=0xffff88003f606a80, mapping=0xffff88001d3824e0, pos=0x108000, len=0x1000, copied=0x0, page=0\ xffffea0000d792e8, fsdata=0x0) at fs/ext4/inode.c:2512 #2 0xffffffff810d97f1 in generic_perform_write (iocb=<value optimized out>, iov=<value optimized out>, nr_segs=<value o\ ptimized out>, pos=0x108000, ppos=0xffff88001e26be40, count=<value optimized out>, written=0x0) at mm/filemap.c:2440 #3 generic_file_buffered_write (iocb=<value optimized out>, iov=<value optimized out>, nr_segs=<value optimized out>, p\ os=0x108000, ppos=0xffff88001e26be40, count=<value optimized out>, written=0x0) at mm/filemap.c:2482 #4 0xffffffff810db5d1 in __generic_file_aio_write (iocb=0xffff88001e26bde8, iov=0xffff88001e26bec8, nr_segs=0x1, ppos=0\ xffff88001e26be40) at mm/filemap.c:2600 #5 0xffffffff810db853 in generic_file_aio_write (iocb=0xffff88001e26bde8, iov=0xffff88001e26bec8, nr_segs=<value optimi\ zed out>, pos=<value optimized out>) at mm/filemap.c:2632 #6 0xffffffff811a71aa in ext4_file_write (iocb=0xffff88001e26bde8, iov=0xffff88001e26bec8, nr_segs=0x1, pos=0x108000) a\ t fs/ext4/file.c:136 #7 0xffffffff811375aa in do_sync_write (filp=0xffff88003f606a80, buf=<value optimized out>, len=<value optimized out>, \ ppos=0xffff88001e26bf48) at fs/read_write.c:406 #8 0xffffffff81137e56 in vfs_write (file=0xffff88003f606a80, buf=0x1ec2960 <Address 0x1ec2960 out of bounds>, count=0x4\ 000, pos=0xffff88001e26bf48) at fs/read_write.c:435 #9 0xffffffff8113816c in sys_write (fd=<value optimized out>, buf=0x1ec2960 <Address 0x1ec2960 out of bounds>, count=0x\ 4000) at fs/read_write.c:487 #10 <signal handler called> #11 0x00007f120077a390 in __brk_reservation_fn_dmi_alloc__ () #12 0x0000000000000000 in ?? () gdb> print offset $22 = 0xffffffffffffffff gdb> print idx $23 = 0xffffffff gdb> print inode->i_blkbits $24 = 0xc gdb> up #1 ext4_da_write_end (file=0xffff88003f606a80, mapping=0xffff88001d3824e0, pos=0x108000, len=0x1000, copied=0x0, page=0\ xffffea0000d792e8, fsdata=0x0) at fs/ext4/inode.c:2512 2512 if (ext4_da_should_update_i_disksize(page, end)) { gdb> print start $25 = 0x0 gdb> print end $26 = 0xffffffffffffffff gdb> print pos $27 = 0x108000 gdb> print new_i_size $28 = 0x108000 gdb> print ((struct ext4_inode_info *)((char *)inode-((int)(&((struct ext4_inode_info *)0)->vfs_inode))))->i_disksize $29 = 0xd9000 gdb> down 2467 for (i = 0; i < idx; i++) gdb> print i $30 = 0xd44acbee This is 100% reproducible with some autonuma development code tuned in a very aggressive manner (not normal way even for knumad) which does "exotic" changes to the ptes. It wouldn't normally trigger but I don't see why it can't happen normally if the page is added to swap cache in between the two faults leading to "copied" being zero (which then hangs in ext4). So it should be fixed. Especially possible with lumpy reclaim (albeit disabled if compaction is enabled) as that would ignore the young bits in the ptes. Signed-off-by: Andrea Arcangeli <aarcange@redhat.com> Signed-off-by: "Theodore Ts'o" <tytso@mit.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* ext4: display the correct mount option in /proc/mounts for [no]init_itableTheodore Ts'o2011-12-211-9/+8
| | | | | | | | | | | | commit fc6cb1cda5db7b2d24bf32890826214b857c728e upstream. /proc/mounts was showing the mount option [no]init_inode_table when the correct mount option that will be accepted by parse_options() is [no]init_itable. Signed-off-by: "Theodore Ts'o" <tytso@mit.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* xen: only limit memory map to maximum reservation for domain 0.Ian Campbell2011-12-211-3/+15
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | commit d3db728125c4470a2d061ac10fa7395e18237263 upstream. d312ae878b6a "xen: use maximum reservation to limit amount of usable RAM" clamped the total amount of RAM to the current maximum reservation. This is correct for dom0 but is not correct for guest domains. In order to boot a guest "pre-ballooned" (e.g. with memory=1G but maxmem=2G) in order to allow for future memory expansion the guest must derive max_pfn from the e820 provided by the toolstack and not the current maximum reservation (which can reflect only the current maximum, not the guest lifetime max). The existing algorithm already behaves this correctly if we do not artificially limit the maximum number of pages for the guest case. For a guest booted with maxmem=512, memory=128 this results in: [ 0.000000] BIOS-provided physical RAM map: [ 0.000000] Xen: 0000000000000000 - 00000000000a0000 (usable) [ 0.000000] Xen: 00000000000a0000 - 0000000000100000 (reserved) -[ 0.000000] Xen: 0000000000100000 - 0000000008100000 (usable) -[ 0.000000] Xen: 0000000008100000 - 0000000020800000 (unusable) +[ 0.000000] Xen: 0000000000100000 - 0000000020800000 (usable) ... [ 0.000000] NX (Execute Disable) protection: active [ 0.000000] DMI not present or invalid. [ 0.000000] e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved) [ 0.000000] e820 remove range: 00000000000a0000 - 0000000000100000 (usable) -[ 0.000000] last_pfn = 0x8100 max_arch_pfn = 0x1000000 +[ 0.000000] last_pfn = 0x20800 max_arch_pfn = 0x1000000 [ 0.000000] initial memory mapped : 0 - 027ff000 [ 0.000000] Base memory trampoline at [c009f000] 9f000 size 4096 -[ 0.000000] init_memory_mapping: 0000000000000000-0000000008100000 -[ 0.000000] 0000000000 - 0008100000 page 4k -[ 0.000000] kernel direct mapping tables up to 8100000 @ 27bb000-27ff000 +[ 0.000000] init_memory_mapping: 0000000000000000-0000000020800000 +[ 0.000000] 0000000000 - 0020800000 page 4k +[ 0.000000] kernel direct mapping tables up to 20800000 @ 26f8000-27ff000 [ 0.000000] xen: setting RW the range 27e8000 - 27ff000 [ 0.000000] 0MB HIGHMEM available. -[ 0.000000] 129MB LOWMEM available. -[ 0.000000] mapped low ram: 0 - 08100000 -[ 0.000000] low ram: 0 - 08100000 +[ 0.000000] 520MB LOWMEM available. +[ 0.000000] mapped low ram: 0 - 20800000 +[ 0.000000] low ram: 0 - 20800000 With this change "xl mem-set <domain> 512M" will successfully increase the guest RAM (by reducing the balloon). There is no change for dom0. Reported-and-Tested-by: George Shuklin <george.shuklin@gmail.com> Signed-off-by: Ian Campbell <ian.campbell@citrix.com> Reviewed-by: David Vrabel <david.vrabel@citrix.com> Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* md/raid5: fix bug that could result in reads from a failed device.NeilBrown2011-12-211-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | commit 355840e7a7e56bb2834fd3b0da64da5465f8aeaa upstream. commit a847627709b3402163d99f7c6fda4a77bcd6b51b in linux-3.0.9 attempted to backport this to 3.0 but only made one change were two were necessary. This add the second change. This bug was introduced in 415e72d034c50520ddb7ff79e7d1792c1306f0c9 which was in 2.6.36. There is a small window of time between when a device fails and when it is removed from the array. During this time we might still read from it, but we won't write to it - so it is possible that we could read stale data. We didn't need the test of 'Faulty' before because the test on In_sync is sufficient. Since we started allowing reads from the early part of non-In_sync devices we need a test on Faulty too. This is suitable for any kernel from 2.6.36 onwards, though the patch might need a bit of tweaking in 3.0 and earlier. Signed-off-by: NeilBrown <neilb@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* xfs: avoid synchronous transactions when deleting attr blocksChristoph Hellwig2011-12-213-28/+4
| | | | | | | | | | | | | | | | | | | | | commit 859f57ca00805e6c482eef1a7ab073097d02c8ca upstream. [slightly different from the upstream version because of a previous cleanup] Currently xfs_attr_inactive causes a synchronous transactions if we are removing a file that has any extents allocated to the attribute fork, and thus makes XFS extremely slow at removing files with out of line extended attributes. The code looks a like a relict from the days before the busy extent list, but with the busy extent list we avoid reusing data and attr extents that have been freed but not commited yet, so this code is just as superflous as the synchronous transactions for data blocks. Signed-off-by: Christoph Hellwig <hch@lst.de> Reported-by: Bernd Schubert <bernd.schubert@itwm.fraunhofer.de> Reviewed-by: Dave Chinner <dchinner@redhat.com> Signed-off-by: Alex Elder <aelder@sgi.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* xfs: fix nfs export of 64-bit inodes numbers on 32-bit kernelsChristoph Hellwig2011-12-211-4/+4
| | | | | | | | | | | | | | | | | commit c29f7d457ac63311feb11928a866efd2fe153d74 upstream. The i_ino field in the VFS inode is of type unsigned long and thus can't hold the full 64-bit inode number on 32-bit kernels. We have the full inode number in the XFS inode, so use that one for nfs exports. Note that I've also switched the 32-bit file handles types to it, just to make the code more consistent and copy & paste errors less likely to happen. Reported-by: Guoquan Yang <ygq51@hotmail.com> Reported-by: Hank Peng <pengxihan@gmail.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Ben Myers <bpm@sgi.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* hwmon: (coretemp) Fix oops on CPU offliningJean Delvare2011-12-211-0/+2
| | | | | | | | | | | | | | | This is for stable kernel branch 3.0 only. Previous and later versions have different code paths and are not affected by this bug. This is the same fix as "hwmon: (coretemp) Fix oops on driver load" but for the CPU offlining case. Sorry for missing it at first. Signed-off-by: Jean Delvare <khali@linux-fr.org> Cc: Durgadoss R <durgadoss.r@intel.com> Acked-by: Guenter Roeck <guenter.roeck@ericsson.com> Cc: Fenghua Yu <fenghua.yu@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* hfs: fix hfs_find_init() sb->ext_tree NULL ptr oopsPhillip Lougher2011-12-211-5/+15
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | commit 434a964daa14b9db083ce20404a4a2add54d037a upstream. Clement Lecigne reports a filesystem which causes a kernel oops in hfs_find_init() trying to dereference sb->ext_tree which is NULL. This proves to be because the filesystem has a corrupted MDB extent record, where the extents file does not fit into the first three extents in the file record (the first blocks). In hfs_get_block() when looking up the blocks for the extent file (HFS_EXT_CNID), it fails the first blocks special case, and falls through to the extent code (which ultimately calls hfs_find_init()) which is in the process of being initialised. Hfs avoids this scenario by always having the extents b-tree fitting into the first blocks (the extents B-tree can't have overflow extents). The fix is to check at mount time that the B-tree fits into first blocks, i.e. fail if HFS_I(inode)->alloc_blocks >= HFS_I(inode)->first_blocks Note, the existing commit 47f365eb57573 ("hfs: fix oops on mount with corrupted btree extent records") becomes subsumed into this as a special case, but only for the extents B-tree (HFS_EXT_CNID), it is perfectly acceptable for the catalog B-Tree file to grow beyond three extents, with the remaining extent descriptors in the extents overfow. This fixes CVE-2011-2203 Reported-by: Clement LECIGNE <clement.lecigne@netasq.com> Signed-off-by: Phillip Lougher <plougher@redhat.com> Cc: Jeff Mahoney <jeffm@suse.com> Cc: Christoph Hellwig <hch@lst.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Cc: Moritz Mühlenhoff <jmm@inutil.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* Make TASKSTATS require root accessLinus Torvalds2011-12-211-0/+1
| | | | | | | | | | | | | | | | | | | | commit 1a51410abe7d0ee4b1d112780f46df87d3621043 upstream. Ok, this isn't optimal, since it means that 'iotop' needs admin capabilities, and we may have to work on this some more. But at the same time it is very much not acceptable to let anybody just read anybody elses IO statistics quite at this level. Use of the GENL_ADMIN_PERM suggested by Johannes Berg as an alternative to checking the capabilities by hand. Reported-by: Vasiliy Kulikov <segoon@openwall.com> Cc: Johannes Berg <johannes.berg@intel.com> Acked-by: Balbir Singh <bsingharora@gmail.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Cc: Moritz Mühlenhoff <jmm@inutil.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* jbd/jbd2: validate sb->s_first in journal_get_superblock()Eryu Guan2011-12-212-0/+16
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | commit 8762202dd0d6e46854f786bdb6fb3780a1625efe upstream. I hit a J_ASSERT(blocknr != 0) failure in cleanup_journal_tail() when mounting a fsfuzzed ext3 image. It turns out that the corrupted ext3 image has s_first = 0 in journal superblock, and the 0 is passed to journal->j_head in journal_reset(), then to blocknr in cleanup_journal_tail(), in the end the J_ASSERT failed. So validate s_first after reading journal superblock from disk in journal_get_superblock() to ensure s_first is valid. The following script could reproduce it: fstype=ext3 blocksize=1024 img=$fstype.img offset=0 found=0 magic="c0 3b 39 98" dd if=/dev/zero of=$img bs=1M count=8 mkfs -t $fstype -b $blocksize -F $img filesize=`stat -c %s $img` while [ $offset -lt $filesize ] do if od -j $offset -N 4 -t x1 $img | grep -i "$magic";then echo "Found journal: $offset" found=1 break fi offset=`echo "$offset+$blocksize" | bc` done if [ $found -ne 1 ];then echo "Magic \"$magic\" not found" exit 1 fi dd if=/dev/zero of=$img seek=$(($offset+23)) conv=notrunc bs=1 count=1 mkdir -p ./mnt mount -o loop $img ./mnt Cc: Jan Kara <jack@suse.cz> Signed-off-by: Eryu Guan <guaneryu@gmail.com> Signed-off-by: "Theodore Ts'o" <tytso@mit.edu> Cc: Moritz Mühlenhoff <jmm@inutil.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* x86, hpet: Immediately disable HPET timer 1 if rtc irq is maskedMark Langsdorf2011-12-211-7/+14
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | commit 2ded6e6a94c98ea453a156748cb7fabaf39a76b9 upstream. When HPET is operating in RTC mode, the TN_ENABLE bit on timer1 controls whether the HPET or the RTC delivers interrupts to irq8. When the system goes into suspend, the RTC driver sends a signal to the HPET driver so that the HPET releases control of irq8, allowing the RTC to wake the system from suspend. The switchover is accomplished by a write to the HPET configuration registers which currently only occurs while servicing the HPET interrupt. On some systems, I have seen the system suspend before an HPET interrupt occurs, preventing the write to the HPET configuration register and leaving the HPET in control of the irq8. As the HPET is not active during suspend, it does not generate a wake signal and RTC alarms do not work. This patch forces the HPET driver to immediately transfer control of the irq8 channel to the RTC instead of waiting until the next interrupt event. Signed-off-by: Mark Langsdorf <mark.langsdorf@amd.com> Link: http://lkml.kernel.org/r/20111118153306.GB16319@alberich.amd.com Tested-by: Andreas Herrmann <andreas.herrmann3@amd.com> Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* mmc: mxcmmc: fix falling back to PIOSascha Hauer2011-12-211-0/+1
| | | | | | | | | | | | | | | commit e58f516ff4730c4047c3f104b061f7a03e9a263c upstream. When we can't configure the dma channel we want to fall back to PIO. We do this by setting host->do_dma to zero. This does not work as do_dma is used to see whether dma can be used for the current transfer. Instead, we have to set host->dma to NULL. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Chris Ball <cjb@laptop.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* hwmon: (jz4740) fix signedness bugAxel Lin2011-12-211-1/+1
| | | | | | | | | | | | | commit 0b57d7602b68f7b2786b2f0e22da39cbd4139a95 upstream. wait_for_completion_interruptible_timeout() may return negative value. In this case, checking if (t > 0) will return true if t is unsigned. Signed-off-by: Axel Lin <axel.lin@gmail.com> Acked-by: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* linux/log2.h: Fix rounddown_pow_of_two(1)Linus Torvalds2011-12-211-1/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | commit 13c07b0286d340275f2d97adf085cecda37ede37 upstream. Exactly like roundup_pow_of_two(1), the rounddown version was buggy for the case of a compile-time constant '1' argument. Probably because it originated from the same code, sharing history with the roundup version from before the bugfix (for that one, see commit 1a06a52ee1b0: "Fix roundup_pow_of_two(1)"). However, unlike the roundup version, the fix for rounddown is to just remove the broken special case entirely. It's simply not needed - the generic code 1UL << ilog2(n) does the right thing for the constant '1' argment too. The only reason roundup needed that special case was because rounding up does so by subtracting one from the argument (and then adding one to the result) causing the obvious problems with "ilog2(0)". But rounddown doesn't do any of that, since ilog2() naturally truncates (ie "rounds down") to the right rounded down value. And without the ilog2(0) case, there's no reason for the special case that had the wrong value. tl;dr: rounddown_pow_of_two(1) should be 1, not 0. Acked-by: Dmitry Torokhov <dtor@vmware.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* mac80211: fix race condition caused by late addBA responseNikolay Martynov2011-12-211-1/+16
| | | | | | | | | | | | | | | | | | | | Upstream commit d305a6557b2c4dca0110f05ffe745b1ef94adb80. If addBA responses comes in just after addba_resp_timer has expired mac80211 will still accept it and try to open the aggregation session. This causes drivers to be confused and in some cases even crash. This patch fixes the race condition and makes sure that if addba_resp_timer has expired addBA response is not longer accepted and we do not try to open half-closed session. Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com> [some adjustments] Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* iwlwifi: do not re-configure HT40 after associatedWey-Yi Guy2011-12-213-28/+28
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | commit 34a5b4b6af104cf18eb50748509528b9bdbc4036 upstream. The ht40 setting should not change after association unless channel switch This fix a problem we are seeing which cause uCode assert because driver sending invalid information and make uCode confuse Here is the firmware assert message: kernel: iwlagn 0000:03:00.0: Microcode SW error detected. Restarting 0x82000000. kernel: iwlagn 0000:03:00.0: Loaded firmware version: 17.168.5.3 build 42301 kernel: iwlagn 0000:03:00.0: Start IWL Error Log Dump: kernel: iwlagn 0000:03:00.0: Status: 0x000512E4, count: 6 kernel: iwlagn 0000:03:00.0: 0x00002078 | ADVANCED_SYSASSERT kernel: iwlagn 0000:03:00.0: 0x00009514 | uPc kernel: iwlagn 0000:03:00.0: 0x00009496 | branchlink1 kernel: iwlagn 0000:03:00.0: 0x00009496 | branchlink2 kernel: iwlagn 0000:03:00.0: 0x0000D1F2 | interruptlink1 kernel: iwlagn 0000:03:00.0: 0x00000000 | interruptlink2 kernel: iwlagn 0000:03:00.0: 0x01008035 | data1 kernel: iwlagn 0000:03:00.0: 0x0000C90F | data2 kernel: iwlagn 0000:03:00.0: 0x000005A7 | line kernel: iwlagn 0000:03:00.0: 0x5080B520 | beacon time kernel: iwlagn 0000:03:00.0: 0xCC515AE0 | tsf low kernel: iwlagn 0000:03:00.0: 0x00000003 | tsf hi kernel: iwlagn 0000:03:00.0: 0x00000000 | time gp1 kernel: iwlagn 0000:03:00.0: 0x29703BF0 | time gp2 kernel: iwlagn 0000:03:00.0: 0x00000000 | time gp3 kernel: iwlagn 0000:03:00.0: 0x000111A8 | uCode version kernel: iwlagn 0000:03:00.0: 0x000000B0 | hw version kernel: iwlagn 0000:03:00.0: 0x00480303 | board version kernel: iwlagn 0000:03:00.0: 0x09E8004E | hcmd kernel: iwlagn 0000:03:00.0: CSR values: kernel: iwlagn 0000:03:00.0: (2nd byte of CSR_INT_COALESCING is CSR_INT_PERIODIC_REG) kernel: iwlagn 0000:03:00.0: CSR_HW_IF_CONFIG_REG: 0X00480303 kernel: iwlagn 0000:03:00.0: CSR_INT_COALESCING: 0X0000ff40 kernel: iwlagn 0000:03:00.0: CSR_INT: 0X00000000 kernel: iwlagn 0000:03:00.0: CSR_INT_MASK: 0X00000000 kernel: iwlagn 0000:03:00.0: CSR_FH_INT_STATUS: 0X00000000 kernel: iwlagn 0000:03:00.0: CSR_GPIO_IN: 0X00000030 kernel: iwlagn 0000:03:00.0: CSR_RESET: 0X00000000 kernel: iwlagn 0000:03:00.0: CSR_GP_CNTRL: 0X080403c5 kernel: iwlagn 0000:03:00.0: CSR_HW_REV: 0X000000b0 kernel: iwlagn 0000:03:00.0: CSR_EEPROM_REG: 0X07d60ffd kernel: iwlagn 0000:03:00.0: CSR_EEPROM_GP: 0X90000001 kernel: iwlagn 0000:03:00.0: CSR_OTP_GP_REG: 0X00030001 kernel: iwlagn 0000:03:00.0: CSR_GIO_REG: 0X00080044 kernel: iwlagn 0000:03:00.0: CSR_GP_UCODE_REG: 0X000093bb kernel: iwlagn 0000:03:00.0: CSR_GP_DRIVER_REG: 0X00000000 kernel: iwlagn 0000:03:00.0: CSR_UCODE_DRV_GP1: 0X00000000 kernel: iwlagn 0000:03:00.0: CSR_UCODE_DRV_GP2: 0X00000000 kernel: iwlagn 0000:03:00.0: CSR_LED_REG: 0X00000078 kernel: iwlagn 0000:03:00.0: CSR_DRAM_INT_TBL_REG: 0X88214dd2 kernel: iwlagn 0000:03:00.0: CSR_GIO_CHICKEN_BITS: 0X27800200 kernel: iwlagn 0000:03:00.0: CSR_ANA_PLL_CFG: 0X00000000 kernel: iwlagn 0000:03:00.0: CSR_HW_REV_WA_REG: 0X0001001a kernel: iwlagn 0000:03:00.0: CSR_DBG_HPET_MEM_REG: 0Xffff0010 kernel: iwlagn 0000:03:00.0: FH register values: kernel: iwlagn 0000:03:00.0: FH_RSCSR_CHNL0_STTS_WPTR_REG: 0X21316d00 kernel: iwlagn 0000:03:00.0: FH_RSCSR_CHNL0_RBDCB_BASE_REG: 0X021479c0 kernel: iwlagn 0000:03:00.0: FH_RSCSR_CHNL0_WPTR: 0X00000060 kernel: iwlagn 0000:03:00.0: FH_MEM_RCSR_CHNL0_CONFIG_REG: 0X80819104 kernel: iwlagn 0000:03:00.0: FH_MEM_RSSR_SHARED_CTRL_REG: 0X000000fc kernel: iwlagn 0000:03:00.0: FH_MEM_RSSR_RX_STATUS_REG: 0X07030000 kernel: iwlagn 0000:03:00.0: FH_MEM_RSSR_RX_ENABLE_ERR_IRQ2DRV: 0X00000000 kernel: iwlagn 0000:03:00.0: FH_TSSR_TX_STATUS_REG: 0X07ff0001 kernel: iwlagn 0000:03:00.0: FH_TSSR_TX_ERROR_REG: 0X00000000 kernel: iwlagn 0000:03:00.0: Start IWL Event Log Dump: display last 20 entries kernel: ------------[ cut here ]------------ WARNING: at net/mac80211/util.c:1208 ieee80211_reconfig+0x1f1/0x407() kernel: Hardware name: 4290W4H kernel: Pid: 1896, comm: kworker/0:0 Not tainted 3.1.0 #2 kernel: Call Trace: kernel: [<ffffffff81036558>] ? warn_slowpath_common+0x73/0x87 kernel: [<ffffffff813b8966>] ? ieee80211_reconfig+0x1f1/0x407 kernel: [<ffffffff8139e8dc>] ? ieee80211_recalc_smps_work+0x32/0x32 kernel: [<ffffffff8139e95a>] ? ieee80211_restart_work+0x7e/0x87 kernel: [<ffffffff810472fa>] ? process_one_work+0x1c8/0x2e3 kernel: [<ffffffff810480c9>] ? worker_thread+0x17a/0x23a kernel: [<ffffffff81047f4f>] ? manage_workers.clone.18+0x15b/0x15b kernel: [<ffffffff81047f4f>] ? manage_workers.clone.18+0x15b/0x15b kernel: [<ffffffff8104ba97>] ? kthread+0x7a/0x82 kernel: [<ffffffff813d21b4>] ? kernel_thread_helper+0x4/0x10 kernel: [<ffffffff8104ba1d>] ? kthread_flush_work_fn+0x11/0x11 kernel: [<ffffffff813d21b0>] ? gs_change+0xb/0xb Reported-by: Udo Steinberg <udo@hypervisor.org> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* percpu: fix chunk range calculationTejun Heo2011-12-212-20/+26
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | commit a855b84c3d8c73220d4d3cd392a7bee7c83de70e upstream. Percpu allocator recorded the cpus which map to the first and last units in pcpu_first/last_unit_cpu respectively and used them to determine the address range of a chunk - e.g. it assumed that the first unit has the lowest address in a chunk while the last unit has the highest address. This simply isn't true. Groups in a chunk can have arbitrary positive or negative offsets from the previous one and there is no guarantee that the first unit occupies the lowest offset while the last one the highest. Fix it by actually comparing unit offsets to determine cpus occupying the lowest and highest offsets. Also, rename pcu_first/last_unit_cpu to pcpu_low/high_unit_cpu to avoid confusion. The chunk address range is used to flush cache on vmalloc area map/unmap and decide whether a given address is in the first chunk by per_cpu_ptr_to_phys() and the bug was discovered by invalid per_cpu_ptr_to_phys() translation for crash_note. Kudos to Dave Young for tracking down the problem. Signed-off-by: Tejun Heo <tj@kernel.org> Reported-by: WANG Cong <xiyou.wangcong@gmail.com> Reported-by: Dave Young <dyoung@redhat.com> Tested-by: Dave Young <dyoung@redhat.com> LKML-Reference: <4EC21F67.10905@redhat.com> Signed-off-by: Thomas Renninger <trenn@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* intel-iommu: fix superpage support in pfn_to_dma_pte()Allen Kay2011-12-211-9/+8
| | | | | | | | | | | | | | | commit 4399c8bf2b9093696fa8160d79712e7346989c46 upstream. If target_level == 0, current code breaks out of the while-loop if SUPERPAGE bit is set. We should also break out if PTE is not present. If we don't do this, KVM calls to iommu_iova_to_phys() will cause pfn_to_dma_pte() to create mapping for 4KiB pages. Signed-off-by: Allen Kay <allen.m.kay@intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com> Signed-off-by: Youquan Song <youquan.song@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* intel-iommu: set iommu_superpage on VM domains to lowest common denominatorAllen Kay2011-12-211-5/+7
| | | | | | | | | | | | | | | | commit 8140a95d228efbcd64d84150e794761a32463947 upstream. set dmar->iommu_superpage field to the smallest common denominator of super page sizes supported by all active VT-d engines. Initialize this field in intel_iommu_domain_init() API so intel_iommu_map() API will be able to use iommu_superpage field to determine the appropriate super page size to use. Signed-off-by: Allen Kay <allen.m.kay@intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com> Signed-off-by: Youquan Song <youquan.song@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* intel-iommu: fix return value of iommu_unmap() APIAllen Kay2011-12-211-3/+8
| | | | | | | | | | | | | | commit 292827cb164ad00cc7689a21283b1261c0b6daed upstream. iommu_unmap() API expects IOMMU drivers to return the actual page order of the address being unmapped. Previous code was just returning page order passed in from the caller. This patch fixes this problem. Signed-off-by: Allen Kay <allen.m.kay@intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com> Signed-off-by: Youquan Song <youquan.song@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* target: Handle 0 correctly in transport_get_sectors_6()Roland Dreier2011-12-211-2/+7
| | | | | | | | | | | | | | | | | | commit 9b5cd7f37e1e018432111333e2a67f78ba41edfe upstream. SBC-3 says: A TRANSFER LENGTH field set to zero specifies that 256 logical blocks shall be written. Any other value specifies the number of logical blocks that shall be written. The old code was always just returning the value in the TRANSFER LENGTH byte. Fix this to return 256 if the byte is 0. Signed-off-by: Roland Dreier <roland@purestorage.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
generated by cgit v1.1 at 2024-10-27 19:32:29 +0000