aboutsummaryrefslogtreecommitdiffstats
path: root/arch/arm/mach-omap2/board-4430sdp.c
Commit message (Collapse)AuthorAgeFilesLines
* OMAPDSS: HDMI: PHY burnout fixTomi Valkeinen2012-03-121-0/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | commit c49d005b6cc8491fad5b24f82805be2d6bcbd3dd upstream. A hardware bug in the OMAP4 HDMI PHY causes physical damage to the board if the HDMI PHY is kept powered on when the cable is not connected. This patch solves the problem by adding hot-plug-detection into the HDMI IP driver. This is not a real HPD support in the sense that nobody else than the IP driver gets to know about the HPD events, but is only meant to fix the HW bug. The strategy is simple: If the display device is turned off by the user, the PHY power is set to OFF. When the display device is turned on by the user, the PHY power is set either to LDOON or TXON, depending on whether the HDMI cable is connected. The reason to avoid PHY OFF when the display device is on, but the cable is disconnected, is that when the PHY is turned OFF, the HDMI IP is not "ticking" and thus the DISPC does not receive pixel clock from the HDMI IP. This would, for example, prevent any VSYNCs from happening, and would thus affect the users of omapdss. By using LDOON when the cable is disconnected we'll avoid the HW bug, but keep the HDMI working as usual from the user's point of view. Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* OMAP: 4430SDP/Panda: add HDMI HPD gpioTomi Valkeinen2012-03-121-0/+3
| | | | | | | | | | | | | commit aa74274b464d4aa24703963ac89a0ee942d5d267 upstream. Both Panda and 4430SDP use GPIO 63 as HDMI hot-plug-detect. Configure this GPIO in the board files. Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* OMAP: 4430SDP/Panda: setup HDMI GPIO muxesTomi Valkeinen2012-03-121-0/+3
| | | | | | | | | | | | | commit 78a1ad8f12db70b8b0a4548b90704de08ee216ce upstream. The HDMI GPIO pins LS_OE and CT_CP_HPD are not currently configured. This patch configures them as output pins. Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* OMAPDSS: remove wrong HDMI HPD muxingTomi Valkeinen2012-03-121-4/+0
| | | | | | | | | | | | | | | commit 7bb122d155f742fe2d79849090c825be7b4a247e upstream. "hdmi_hpd" pin is muxed to INPUT and PULLUP, but the pin is not currently used, and in the future when it is used, the pin is used as a GPIO and is board specific, not an OMAP4 wide thing. So remove the muxing for now. Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* OMAP: 4430SDP/Panda: rename HPD GPIO to CT_CP_HPDTomi Valkeinen2012-03-121-2/+2
| | | | | | | | | | | | | | | commit 3932a32fcf5393f8be70ac99dc718ad7ad0a415b upstream. The GPIO 60 on 4430sdp and Panda is not HPD GPIO, as currently marked in the board files, but CT_CP_HPD, which is used to enable/disable HPD functionality. This patch renames the GPIO. Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* OMAP: 4430SDP/Panda: use gpio_free_array to free HDMI gpiosTomi Valkeinen2012-03-121-2/+1
| | | | | | | | | | | commit 575753e3bea3b67eef8e454fb87f719e3f7da599 upstream. Instead of freeing the GPIOs individually, use gpio_free_array(). Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* OMAP: DSS2: HDMI: use default dividersTomi Valkeinen2012-03-121-9/+0
| | | | | | | | | | | | | commit 8d88767a4377171752c22ac39bcb2b505eb751da upstream. Use default regn and regm2 dividers in the hdmi driver if the board file does not define them. Cc: Mythri P K <mythripk@ti.com> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* ARM: OMAP4: MMC: no regulator off during probe for eMMCBalaji T K2011-06-011-0/+1
| | | | | | | | | | | | | | eMMC does not handle power off when not in sleep state, Skip regulator disable during probe when eMMC is not in known state - state left by bootloader. Resolves eMMC failure on OMAP4 mmc0: error -110 whilst initialising MMC card Signed-off-by: Balaji T K <balajitk@ti.com> Tested-by: Kishore Kadiyala <kishore.kadiyala@ti.com> Acked-by: Kishore Kadiyala <kishore.kadiyala@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
* ARM: omap4: Pass core and wakeup mux tables to omap4_mux_initColin Cross2011-06-011-1/+1
| | | | | | | | | OMAP4 contains two separate instances of the padconf registers, one in the core system config and one in the wakeup system config. Pass in two tables to apply the correct values to each instance. Signed-off-by: Colin Cross <ccross@android.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
* OMAP2+: Fix 9 section mismatch(es) warnings from mach-omap2/built-in.oSantosh Shilimkar2011-05-311-4/+4
| | | | | | | | | | | The serial*_data should have been marked as __initdata as per it's usage in the board files. Fix the same to remove the section mismatch warnings caused by it. Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com> Signed-off-by: Silesh C V <silesh@ti.com> [tony@atomide.com: updated with additional fixes from Silesh] Signed-off-by: Tony Lindgren <tony@atomide.com>
* Merge branch 'omap-for-linus' of ↵Linus Torvalds2011-05-261-89/+25
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6 * 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (33 commits) OMAP3: PM: Boot message is not an error, and not helpful, remove it OMAP3: cpuidle: change the power domains modes determination logic OMAP3: cpuidle: code rework for improved readability OMAP3: cpuidle: re-organize the C-states data OMAP3: clean-up mach specific cpuidle data structures OMAP3 cpuidle: remove useless SDP specific timings usb: otg: OMAP4430: Powerdown the internal PHY when USB is disabled usb: otg: OMAP4430: Fixing the omap4430_phy_init function usb: musb: am35x: fix compile error when building am35x usb: musb: OMAP4430: Power down the PHY during board init omap: drop board-igep0030.c omap: igep0020: add support for IGEP3 omap: igep0020: minor refactoring omap: igep0020: name refactoring for future merge with IGEP3 omap: Remove support for omap2evm arm: omap2plus: GPIO cleanup omap: musb: introduce default board config omap: move detection of NAND CS to common-board-devices omap: use common initialization for PMIC i2c bus omap: consolidate touch screen initialization among different boards ...
| * arm: omap2plus: GPIO cleanupIgor Grinberg2011-05-121-75/+23
| | | | | | | | | | | | | | | | use gpio_request_<one|array>() instead of multiple gpiolib calls, remove unneeded variables, etc. Signed-off-by: Igor Grinberg <grinberg@compulab.co.il> Signed-off-by: Tony Lindgren <tony@atomide.com>
| * omap: use common initialization for PMIC i2c busMike Rapoport2011-05-031-14/+2
| | | | | | | | | | | | | | | | Introduce omap_pmic_init that registers i2c bus and PMIC device on that bus and add omap2/3/4 wrappers for common cases. Signed-off-by: Mike Rapoport <mike@compulab.co.il> Signed-off-by: Tony Lindgren <tony@atomide.com>
* | OMAP: DSS2: HDMI: Use dss_device clock configuration for HDMI PLL parametersArchit Taneja2011-05-111-0/+9
| | | | | | | | | | | | | | | | | | Move some of the configurable HDMI PLL parameters to dssdev.clock struct. Cleanup the function hdmi_compute_pll() by using the parameters defined in the board file and do some cosmetic modifications. Signed-off-by: Archit Taneja <archit@ti.com> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
* | OMAP: DSS2: Move display.h to include/video/Tomi Valkeinen2011-05-111-1/+1
|/ | | | | | | arch/arm/plat-omap/include/plat/display.h is an include for the OMAP DSS driver. A more logical place for it is in include/video. Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
* Merge branch 'for-next' of ↵Linus Torvalds2011-03-241-0/+7
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6 * 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (90 commits) mfd: Push byte swaps out of wm8994 bulk read path mfd: Rename ab8500 gpadc header mfd: Constify WM8994 write path mfd: Push byte swap out of WM8994 bulk I/O mfd: Avoid copying data in WM8994 I2C write mfd: Remove copy from WM831x I2C write function mfd: Staticise WM8994 PM ops regulator: Add a subdriver for TI TPS6105x regulator portions v2 mfd: Add a core driver for TI TPS61050/TPS61052 chips v2 gpio: Add Tunnel Creek support to sch_gpio mfd: Add Tunnel Creek support to lpc_sch pci_ids: Add Intel Tunnel Creek LPC Bridge device ID. regulator: MAX8997/8966 support mfd: Add WM8994 bulk register write operation mfd: Append additional read write on 88pm860x mfd: Adopt mfd_data in 88pm860x input driver mfd: Adopt mfd_data in 88pm860x regulator mfd: Adopt mfd_data in 88pm860x led mfd: Adopt mfd_data in 88pm860x backlight mfd: Fix MAX8997 Kconfig entry typos ...
| * OMAP4: add clk32kg data to omap4panda and blaze board fileBalaji T K2011-03-231-0/+7
| | | | | | | | | | | | | | | | | | | | | | In Blaze and Panda, 32KHz clock - CLK32KG to WLAN is supplied from Phoenix TWL6030. Add CLK32KG platform data to blaze and omap4panda board file. Signed-off-by: Balaji T K <balajitk@ti.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* | Merge branch 'for-paul' of git://gitorious.org/linux-omap-dss2/linuxPaul Mundt2011-03-221-0/+75
|\ \ | |/ |/| | | | | | | | | Conflicts: arch/arm/mach-omap2/board-overo.c Signed-off-by: Paul Mundt <lethal@linux-sh.org>
| * OMAP4: HDMI: Add HDMI structure in the board file for OMAP4 SDPMythri P K2011-03-161-0/+75
| | | | | | | | | | | | | | | | | | | | Adding board file structure for display which adds the display structure with HDMI as the default driver when the display init is called. HDMI GPIO configurations are also done in this file. Signed-off-by: Mythri P K <mythripk@ti.com> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
* | Merge branch 'omap-for-linus' of ↵Linus Torvalds2011-03-171-18/+172
|\ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6 * 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (258 commits) omap: zoom: host should not pull up wl1271's irq line arm: plat-omap: iommu: fix request_mem_region() error path OMAP2+: Common CPU DIE ID reading code reads wrong registers for OMAP4430 omap4: mux: Remove duplicate mux modes omap: iovmm: don't check 'da' to set IOVMF_DA_FIXED flag omap: iovmm: disallow mapping NULL address when IOVMF_DA_ANON is set omap2+: mux: Fix compile when CONFIG_OMAP_MUX is not selected omap4: board-omap4panda: Initialise the serial pads omap3: board-3430sdp: Initialise the serial pads omap4: board-4430sdp: Initialise the serial pads omap2+: mux: Add macro for configuring static with omap_hwmod_mux_init omap2+: mux: Remove the use of IDLE flag omap2+: Add separate list for dynamic pads to mux perf: add OMAP support for the new power events OMAP4: Add IVA OPP enteries. OMAP4: Update Voltage Rail Values for MPU, IVA and CORE OMAP4: Enable 800 MHz and 1 GHz MPU-OPP OMAP3+: OPP: Replace voltage values with Macros OMAP3: wdtimer: Fix CORE idle transition Watchdog: omap_wdt: add fine grain runtime-pm ... Fix up various conflicts in - arch/arm/mach-omap2/board-omap3evm.c - arch/arm/mach-omap2/clock3xxx_data.c - arch/arm/mach-omap2/usb-musb.c - arch/arm/plat-omap/include/plat/usb.h - drivers/usb/musb/musb_core.h
| * | omap4: board-4430sdp: Initialise the serial padsR Sricharan2011-03-111-2/+69
| |/ | | | | | | | | | | | | Use the mux framework to initialise the serial pads. Signed-off-by: sricharan <r.sricharan@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
| *-. Merge branches 'devel-iommu-mailbox', 'devel-mcbsp', 'devel-board' and ↵Tony Lindgren2011-03-021-9/+10
| |\ \ | | | | | | | | | | | | | | | | | | | | | | | | 'devel-hsmmc' into omap-for-linus Conflicts: arch/arm/mach-omap2/omap_hwmod_44xx_data.c
| | | * OMAP: hsmmc: Rename the device and driverKishore Kadiyala2011-03-011-7/+7
| | |/ | |/| | | | | | | | | | | | | | | | | | | | | | Modifying the device & driver name from "mmci-omap-hs" to "omap_hsmmc". Signed-off-by: Kishore Kadiyala <kishore.kadiyala@ti.com> Acked-by: Benoit Cousson<b-cousson@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
| | * omap2+: Minimize board specific init_early callsTony Lindgren2011-02-251-2/+3
| |/ | | | | | | | | | | | | We should only call init_common_infrastructure and init_common_devices from init_early. Signed-off-by: Tony Lindgren <tony@atomide.com>
| *---. Merge branches 'devel-cleanup', 'devel-omap4', 'devel-board' and ↵Tony Lindgren2011-02-231-3/+89
| |\ \ \ | | | | | | | | | | | | | | | 'devel-nand' into omap-for-linus
| | | | * OMAP4: Fix -EINVAL for vana, vcxio, vdacBalaji T K2011-02-221-3/+0
| | | |/ | | |/| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Fixed regulators in twl6030 do not have set_voltage hook. Regulator core returns -22 if set_voltage is NULL and apply_uV is set while applying the constraint to set voltage resulting in failure during probe of these regulators. Do not set apply_uV for fixed regulators which don't have set_voltage. machine_constraints_voltage: VANA: failed to apply 2100000uV constraint twl_reg twl_reg.43: can't register VANA, -22 twl_reg: probe of twl_reg.43 failed with error -22 machine_constraints_voltage: VCXIO: failed to apply 1800000uV constraint twl_reg twl_reg.44: can't register VCXIO, -22 twl_reg: probe of twl_reg.44 failed with error -22 machine_constraints_voltage: VDAC: failed to apply 1800000uV constraint twl_reg twl_reg.45: can't register VDAC, -22 twl_reg: probe of twl_reg.45 failed with error -22 Signed-off-by: Balaji T K <balajitk@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
| | | * OMAP4: keypad: Add the board supportSyed Rafiuddin2011-02-171-0/+89
| | |/ | | | | | | | | | | | | | | | | | | | | | | | | | | | -Add the platform changes for the keypad driver -Register keyboard device with hwmod framework. Signed-off-by: Syed Rafiuddin <rafiuddin.syed@ti.com> Signed-off-by: Abraham Arce <x0066660@ti.com> Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
| * | Merge branch 'for-tony' of git://gitorious.org/usb/usb into omap-for-linusTony Lindgren2011-02-221-19/+0
| |\ \ | | |/ | |/| | | | | | | | | | Conflicts: arch/arm/mach-omap2/omap_hwmod_2430_data.c arch/arm/mach-omap2/omap_hwmod_3xxx_data.c
| | * arm: omap4: 4430sdp: drop ehci supportAnand Gadiyar2011-02-171-19/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Most revisions of the OMAP4 Blaze/SDP platform do not have the EHCI signals routed by default. The pads are routed for the alternate HSI functionality instead, and explicit board modifications are needed to route the signals to the USB PHY on the board. Also, turning on the PHY connected to the EHCI port causes a board reboot during bootup due to an unintended short on the rails - this affects many initial revisions of the board, and needs a minor board mod to fix (or as a workaround, one should not attempt to power on the USB PHY). Given that these boards need explicit board mods to even get EHCI working (separate from the accidental short above), we should not attempt to enable EHCI by default. So drop the EHCI support from the board files for the Blaze/SDP platforms. Signed-off-by: Anand Gadiyar <gadiyar@ti.com> Cc: Keshava Munegowda <keshava_mgowda@ti.com> Cc: Tony Lindgren <tony@atomide.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
| * | ARM: OMAP2: use early init hookRussell King - ARM Linux2011-02-141-4/+4
| |/ | | | | | | | | | | | | | | Move non-mapping and non-irq initialization code out of .map_io and .init_irq respectively into the new init_early hook. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Tony Lindgren <tony@atomide.com>
* | arm: omap4: 4430sdp: drop ehci supportAnand Gadiyar2011-03-071-19/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Most revisions of the OMAP4 Blaze/SDP platform do not have the EHCI signals routed by default. The pads are routed for the alternate HSI functionality instead, and explicit board modifications are needed to route the signals to the USB PHY on the board. Also, turning on the PHY connected to the EHCI port causes a board reboot during bootup due to an unintended short on the rails - this affects many initial revisions of the board, and needs a minor board mod to fix (or as a workaround, one should not attempt to power on the USB PHY). Given that these boards need explicit board mods to even get EHCI working (separate from the accidental short above), we should not attempt to enable EHCI by default. So drop the EHCI support from the board files for the Blaze/SDP platforms. Signed-off-by: Anand Gadiyar <gadiyar@ti.com> Cc: Keshava Munegowda <keshava_mgowda@ti.com> Cc: Tony Lindgren <tony@atomide.com> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* | arm: omap: usb: Invoke usbhs core device initializationKeshava Munegowda2011-03-011-1/+1
| | | | | | | | | | | | | | | | The usbhs intialization is invoked by all omap3 and omap4 variant board files. Signed-off-by: Keshava Munegowda <keshava_mgowda@ti.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
* | arm: omap: usb: create common enums and structures for ehci and ohciKeshava Munegowda2011-03-011-5/+5
| | | | | | | | | | | | | | | | Create the ehci and ohci specific platform data structures. The port enum values are made common for both ehci and ohci. Signed-off-by: Keshava Munegowda <keshava_mgowda@ti.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
* | usb: otg: OMAP4430: Introducing suspend function for power managementHema HK2011-02-181-0/+1
|/ | | | | | | | | | | | | | | Introduced the suspend/resume function for the OMAP4430 internal PHY. This will be used by the twl6030-usb transceiver driver. Moved the clock enable/disable function calls and power on/off of the PHY code from power on/off functions to suspend/resume function. Pass the suspend function through board data for OMAP4430sdp and OMAP4panda. This will be used by the twl6030-usb transceiver driver. Signed-off-by: Hema HK <hemahk@ti.com> Cc: Tony Lindgren <tony@atomide.com> Cc: Paul Walmsley <paul@pwsan.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
* omap4: Fix ULPI PHY init for ES1.0 SDPTony Lindgren2011-01-131-4/+6
| | | | | | | | | | | | | | | | Commit 6aa85a5ae610106d89e50c7e1f760c56d12f9bc4 (omap4: 4430sdp: enable the ehci port on 4430SDP) added code to enable EHCI support on 4430sdp board. Looks like the ULPI pin does not seem to be muxed properly on ES1.0 SDP and this causes the system to reboot when the ULPI PHY is enabled. Fix this by muxing the pin, this is the same setting for both ES1.0 and ES2.0. Also add checking for gpio_request. Cc: Keshava Munegowda <keshava_mgowda@ti.com Signed-off-by: Tony Lindgren <tony@atomide.com>
* Merge branch 'usb-next' of ↵Linus Torvalds2011-01-071-6/+29
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6 * 'usb-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (144 commits) USB: add support for Dream Cheeky DL100B Webmail Notifier (1d34:0004) USB: serial: ftdi_sio: add support for TIOCSERGETLSR USB: ehci-mxc: Setup portsc register prior to accessing OTG viewport USB: atmel_usba_udc: fix freeing irq in usba_udc_remove() usb: ehci-omap: fix tll channel enable mask usb: ohci-omap3: fix trivial typo USB: gadget: ci13xxx: don't assume that PAGE_SIZE is 4096 USB: gadget: ci13xxx: fix complete() callback for no_interrupt rq's USB: gadget: update ci13xxx to work with g_ether USB: gadgets: ci13xxx: fix probing of compiled-in gadget drivers Revert "USB: musb: pm: don't rely fully on clock support" Revert "USB: musb: blackfin: pm: make it work" USB: uas: Use GFP_NOIO instead of GFP_KERNEL in I/O submission path USB: uas: Ensure we only bind to a UAS interface USB: uas: Rename sense pipe and sense urb to status pipe and status urb USB: uas: Use kzalloc instead of kmalloc USB: uas: Fix up the Sense IU usb: musb: core: kill unneeded #include's DA8xx: assign name to MUSB IRQ resource usb: gadget: g_ncm added ... Manually fix up trivial conflicts in USB Kconfig changes in: arch/arm/mach-omap2/Kconfig arch/sh/Kconfig drivers/usb/Kconfig drivers/usb/host/ehci-hcd.c and annoying chip clock data conflicts in: arch/arm/mach-omap2/clock3xxx_data.c arch/arm/mach-omap2/clock44xx_data.c
| * arm: OMAP4430: musb: Configure musb to OTG modeHema HK2010-12-101-1/+1
| | | | | | | | | | | | | | | | Enabling the musb OTG mode for SDP and PANDA boards. Signed-off-by: Hema HK <hemahk@ti.com> Cc: Tony Lindgren <tony@atomide.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
| * mfd: TWL6030: OMAP4: Registering the TWL6030-usb deviceHema HK2010-12-101-3/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | Registering the twl6030-usb transceiver device as a child to twl6030 core. Removed the NOP transceiver init call from board file. Populated twl4030_usb_data platform data structure with the function pointers for OMAP4430 internal PHY operation to be used by twl630-usb driver. Signed-off-by: Hema HK <hemahk@ti.com> Cc: Samuel Ortiz <sameo@linux.intel.com> Cc: Tony Lindgren <tony@atomide.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
| * arm: omap4: enable usb on 4430sdpFelipe Balbi2010-12-101-3/+1
| | | | | | | | | | | | | | Let musb work on 4430sdp as well. We can now test any problems with multi-omap builds. Signed-off-by: Felipe Balbi <balbi@ti.com>
| * omap4: 4430sdp: enable the ehci port on 4430SDPKeshava Munegowda2010-12-011-0/+20
| | | | | | | | | | | | | | | | | | | | | | The OMAP4 SDP has an SMSC3320 PHY hooked up to EHCI on Port1. The PHY power is controlled by GPIO 157. Turn on the PHY power, and register the controller at init. Signed-off-by: Keshava Munegowda <keshava_mgowda@ti.com> Signed-off-by: Anand Gadiyar <gadiyar@ti.com> Acked-by: Tony Lindgren <tony@atomide.com>
* | OMAP2+: io: split omap2_init_common_hw()Paul Walmsley2010-12-211-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Split omap2_init_common_hw() into two functions. The first, omap2_init_common_infrastructure(), initializes the hwmod code and data, the OMAP PM code, and the clock code and data. The second, omap2_init_common_devices(), handles any other early device initialization that, for whatever reason, has not been or cannot be moved to initcalls or early platform devices. This patch is required for the hwmod postsetup patch, which allows board files to change the state that hwmods should be placed into at the conclusion of the hwmod _setup() function. For example, for a board whose creators wish to ensure watchdog coverage across the entire kernel boot process, code to change the watchdog's postsetup state will be added in the board-*.c file between the omap2_init_common_infrastructure() and omap2_init_common_devices() function calls. Signed-off-by: Paul Walmsley <paul@pwsan.com> Cc: Tony Lindgren <tony@atomide.com>
* | omap4: Add platform changes for PWM LEDHemanth V2010-12-201-0/+24
| | | | | | | | | | | | | | Register TWL6030 PWM, which is used as charging LED Signed-off-by: Hemanth V <hemanthv@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
* | omap4: Add platform changes for Ambient Light sensorHemanth V2010-12-201-0/+3
| | | | | | | | | | | | | | | | Register BH1780GLI Ambient light sensor, which is an I2C device for 4430SDP board. Signed-off-by: Hemanth V <hemanthv@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
* | OMAP: GPIO: Implement GPIO as a platform deviceVaradarajan, Charulatha2010-12-071-1/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Implement GPIO as a platform device. GPIO APIs are used in machine_init functions. Hence it is required to complete GPIO probe before board_init. Therefore GPIO device register and driver register are implemented as postcore_initcalls. omap_gpio_init() does nothing now and this function would be removed in the next patch as it's usage is spread across most of the board files. Inorder to convert GPIO as platform device, modifications are required in clockxxxx_data.c file for OMAP1 so that device names can be used to obtain clock instead of getting clocks by name/NULL ptr. Use runtime pm APIs (pm_runtime_put*/pm_runtime_get*) for enabling or disabling the clocks, modify sysconfig settings and remove usage of clock FW APIs. Note 1: Converting GPIO driver to use runtime PM APIs is not done as a separate patch because GPIO clock names are different for various OMAPs and are different for some of the banks in the same CPU. This would need usage of cpu_is checks and bank id checks while using clock FW APIs in the gpio driver. Hence while making GPIO a platform driver framework, PM runtime APIs are used directly. Note 2: While implementing GPIO as a platform device, pm runtime APIs are used as mentioned above and modification is not done in gpio's prepare for idle/ resume after idle functions. This would be done in the next patch series and GPIO driver would be made to use dev_pm_ops instead of sysdev_class in that series only. Due to the above, the GPIO driver implicitly relies on CM_AUTOIDLE = 1 on its iclk for power management to work, since the driver never disables its iclk. This would be taken care in the next patch series (see Note 3 below). Refer to http://www.mail-archive.com/linux-omap@vger.kernel.org/msg39112.html for more details. Note 3: only pm_runtime_get_sync is called in gpio's probe() and pm_runtime_put* is never called. This is to make the implementation similar to the existing GPIO code. Another patch series would be sent to correct this. In OMAP3 and OMAP4 gpio's debounce clocks are optional clocks. They are enabled/ disabled whenever required using clock framework APIs TODO: 1. Cleanup the GPIO driver. Use function pointers and register offest pointers instead of using hardcoded values 2. Remove all cpu_is_ checks and OMAP specific macros 3. Remove usage of gpio_bank array so that only instance specific information is used in driver code 4. Rename 'method'/ avoid it's usage 5. Fix the non-wakeup gpios handling for OMAP2430, OMAP3 & OMAP4 6. Modify gpio's prepare for idle/ resume after idle functions to use runtime pm implentation. Signed-off-by: Charulatha V <charu@ti.com> Signed-off-by: Rajendra Nayak <rnayak@ti.com> Reviewed-by: Basak, Partha <p-basak2@ti.com> Acked-by: Kevin Hilman <khilman@deeprootsystems.com> [tony@atomide.com: updated for bank specific revision and updated boards] Signed-off-by: Tony Lindgren <tony@atomide.com>
* | OMAP4: sdp4430: Select CBS package for ES2Benoit Cousson2010-11-171-1/+5
| | | | | | | | | | | | | | | | | | | | | | Select the CBS package if SDP4430 is enabled during config. Use the proper package (CBL or CBS) based on chip revision. Signed-off-by: Benoit Cousson <b-cousson@ti.com> Cc: Tony Lindgren <tony@atomide.com> Cc: Paul Walmsley <paul@pwsan.com> Cc: Santosh Shilimkar <santosh.shilimkar@ti.com> Cc: Anand Gadiyar <gadiyar@ti.com>
* | OMAP4: sdp4430: Select CBL package for ES1 and initialize muxBenoit Cousson2010-11-171-0/+10
|/ | | | | | | | | | Select the CBL package if SDP4430 is enabled during config. Initialize the mux framework during the board init. Signed-off-by: Benoit Cousson <b-cousson@ti.com> Cc: Tony Lindgren <tony@atomide.com> Cc: Paul Walmsley <paul@pwsan.com> Cc: Kevin Hilman <khilman@deeprootsystems.com>
* mfd: Adding twl6030 mmc card detect support for MMC1kishore kadiyala2010-10-291-1/+6
| | | | | | | | | | | | | | | | | | | | | | | | | Adding card detect callback function and card detect configuration function for MMC1 Controller on OMAP4. Card detect configuration function does initial configuration of the MMC Control & PullUp-PullDown registers of Phoenix. For MMC1 Controller, card detect interrupt source is twl6030 which is non-gpio. The card detect call back function provides card present/absent status by reading MMC Control register present on twl6030. Since OMAP4 doesn't use any GPIO line as used in OMAP3 for card detect, the suspend/resume initialization which was done in omap_hsmmc_gpio_init previously is moved to the probe thus making it generic for both OMAP3 & OMAP4. Cc: Tony Lindgren <tony@atomide.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Madhusudhan Chikkature <madhu.cr@ti.com> Cc: Adrian Hunter <adrian.hunter@nokia.com> Signed-off-by: Kishore Kadiyala <kishore.kadiyala@ti.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* Merge branch 'omap-for-linus' of ↵Linus Torvalds2010-10-251-6/+81
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6 * 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (163 commits) omap: complete removal of machine_desc.io_pg_offst and .phys_io omap: UART: fix wakeup registers for OMAP24xx UART2 omap: Fix spotty MMC voltages ASoC: OMAP4: MCPDM: Remove unnecessary include of plat/control.h serial: omap-serial: fix signess error OMAP3: DMA: Errata i541: sDMA FIFO draining does not finish omap: dma: Fix buffering disable bit setting for omap24xx omap: serial: Fix the boot-up crash/reboot without CONFIG_PM OMAP3: PM: fix scratchpad memory accesses for off-mode omap4: pandaboard: enable the ehci port on pandaboard omap4: pandaboard: Fix the init if CONFIG_MMC_OMAP_HS is not set omap4: pandaboard: remove unused hsmmc definition OMAP: McBSP: Remove null omap44xx ops comment OMAP: McBSP: Swap CLKS source definition OMAP: McBSP: Fix CLKR and FSR signal muxing OMAP2+: clock: reduce the amount of standard debugging while disabling unused clocks OMAP: control: move plat-omap/control.h to mach-omap2/control.h OMAP: split plat-omap/common.c OMAP: McBSP: implement functional clock switching via clock framework OMAP: McBSP: implement McBSP CLKR and FSR signal muxing via mach-omap2/mcbsp.c ... Fixed up trivial conflicts in arch/arm/mach-omap2/ {board-zoom-peripherals.c,devices.c} as per Tony
| * OMAP: control: move plat-omap/control.h to mach-omap2/control.hPaul Walmsley2010-10-081-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Only OMAP2+ platforms have the System Control Module (SCM) IP block. In the past, we've kept the SCM header file in plat-omap. This has led to abuse - device drivers including it; includes being added that create implicit dependencies on OMAP2+ builds; etc. In response, move the SCM headers into mach-omap2/. As part of this, remove the direct SCM access from the OMAP UDC driver. It was clearly broken. The UDC code needs an indepth review for use on OMAP2+ chips. Signed-off-by: Paul Walmsley <paul@pwsan.com> Cc: Cory Maccarrone <darkstar6262@gmail.com> Cc: Kyungmin Park <kyungmin.park@samsung.com>
| *-. Merge branches 'devel-omap1' and 'devel-omap2plus' into omap-for-linusTony Lindgren2010-10-081-1/+8
| |\ \
generated by cgit v1.1 at 2024-06-02 12:11:24 +0000