aboutsummaryrefslogtreecommitdiffstats
path: root/drivers/i2c
Commit message (Collapse)AuthorAgeFilesLines
* initial merge with 3.2.72Wolfgang Wiedmeyer2015-10-234-0/+1432
|\
| * i2c: davinci: generate STP always when NACK is receivedGrygorii Strashko2015-01-011-5/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | commit 9ea359f7314132cbcb5a502d2d8ef095be1f45e4 upstream. According to I2C specification the NACK should be handled as follows: "When SDA remains HIGH during this ninth clock pulse, this is defined as the Not Acknowledge signal. The master can then generate either a STOP condition to abort the transfer, or a repeated START condition to start a new transfer." [I2C spec Rev. 6, 3.1.6: http://www.nxp.com/documents/user_manual/UM10204.pdf] Currently the Davinci i2c driver interrupts the transfer on receipt of a NACK but fails to send a STOP in some situations and so makes the bus stuck until next I2C IP reset (idle/enable). For example, the issue will happen during SMBus read transfer which consists from two i2c messages write command/address and read data: S Slave Address Wr A Command Code A Sr Slave Address Rd A D1..Dn A P <--- write -----------------------> <--- read ---------------------> The I2C client device will send NACK if it can't recognize "Command Code" and it's expected from I2C master to generate STP in this case. But now, Davinci i2C driver will just exit with -EREMOTEIO and STP will not be generated. Hence, fix it by generating Stop condition (STP) always when NACK is received. This patch fixes Davinci I2C in the same way it was done for OMAP I2C commit cda2109a26eb ("i2c: omap: query STP always when NACK is received"). Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Reported-by: Hein Tibosch <hein_tibosch@yahoo.es> Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
| * i2c: s3c2410: resume race fixOlof Johansson2014-06-091-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | commit ce78cc071f5f541480e381cc0241d37590041a9d upstream. Don't unmark the device as suspended until after it's been re-setup. The main race would be w.r.t. an i2c driver that gets resumed at the same time (asyncronously), that is allowed to do a transfer since suspended is set to 0 before reinit, but really should have seen the -EIO return instead. Signed-off-by: Olof Johansson <olof@lixom.net> Signed-off-by: Doug Anderson <dianders@chromium.org> Acked-by: Kukjin Kim <kgene.kim@samsung.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> [bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
| * i2c: designware: Mask all interrupts during i2c controller enableDu, Wenkai2014-06-091-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | commit 47bb27e78867997040a228328f2a631c3c7f2c82 upstream. There have been "i2c_designware 80860F41:00: controller timed out" errors on a number of Baytrail platforms. The issue is caused by incorrect value in Interrupt Mask Register (DW_IC_INTR_MASK) when i2c core is being enabled. This causes call to __i2c_dw_enable() to immediately start the transfer which leads to timeout. There are 3 failure modes observed: 1. Failure in S0 to S3 resume path The default value after reset for DW_IC_INTR_MASK is 0x8ff. When we start the first transaction after resuming from system sleep, TX_EMPTY interrupt is already unmasked because of the hardware default. 2. Failure in normal operational path This failure happens rarely and is hard to reproduce. Debug trace showed that DW_IC_INTR_MASK had value of 0x254 when failure occurred, which meant TX_EMPTY was unmasked. 3. Failure in S3 to S0 suspend path This failure also happens rarely and is hard to reproduce. Adding debug trace that read DW_IC_INTR_MASK made this failure not reproducible. But from ISR call trace we could conclude TX_EMPTY was unmasked when problem occurred. The patch masks all interrupts before the controller is enabled to resolve the faulty DW_IC_INTR_MASK conditions. Signed-off-by: Wenkai Du <wenkai.du@intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> [wsa: improved the comment and removed typo in commit msg] Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
| * i2c: piix4: Add support for AMD ML and CZ SMBus changesShane Huang2014-04-022-4/+23
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | commit 032f708bc4f6da868ec49dac48ddf3670d8035d3 upstream. The locations of SMBus register base address and enablement bit are changed from AMD ML, which need this patch to be supported. Signed-off-by: Shane Huang <shane.huang@amd.com> Reviewed-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> [bwh: Backported to 3.2: - Adjust context - Aux bus support is not included] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
| * i2c-piix4: Add AMD CZ SMBus device IDShane Huang2013-07-272-1/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | commit b996ac90f595dda271cbd858b136b45557fc1a57 upstream. To add AMD CZ SMBus controller device ID. [bhelgaas: drop pci_ids.h update] Signed-off-by: Shane Huang <shane.huang@amd.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Tejun Heo <tj@kernel.org> Reviewed-by: Jean Delvare <khali@linux-fr.org> [bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
| * i2c: designware: always clear interrupts before enabling themMika Westerberg2013-05-301-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | commit 2a2d95e9d6d29e726cc294b65391917ed2e32bf4 upstream. If the I2C bus is put to a low power state by an ACPI method it might pull the SDA line low (as its power is removed). Once the bus is put to full power state again, the SDA line is pulled back to high. This transition looks like a STOP condition from the controller point-of-view which sets STOP detected bit in its status register causing the driver to fail subsequent transfers. Fix this by always clearing all interrupts before we start a transfer. Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
| * i2c: xiic: must always write 16-bit words to TX_FIFOSteven A. Falco2013-05-131-4/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | commit c39e8e4354ce4daf23336de5daa28a3b01f00aa6 upstream. The TX_FIFO register is 10 bits wide. The lower 8 bits are the data to be written, while the upper two bits are flags to indicate stop/start. The driver apparently attempted to optimize write access, by only writing a byte in those cases where the stop/start bits are zero. However, we have seen cases where the lower byte is duplicated onto the upper byte by the hardware, which causes inadvertent stop/starts. This patch changes the write access to the transmit FIFO to always be 16 bits wide. Signed off by: Steven A. Falco <sfalco@harris.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
| * i2c: tegra: check the clk_prepare_enable() return valueLaxman Dewangan2013-03-271-2/+11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | commit 132c803f7b70b17322579f6f4f3f65cf68e55135 upstream. NVIDIA's Tegra SoC allows read/write of controller register only if controller clock is enabled. System hangs if read/write happens to registers without enabling clock. clk_prepare_enable() can be fail due to unknown reason and hence adding check for return value of this function. If this function success then only access register otherwise return to caller with error. Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com> Reviewed-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> [bwh: Backported to 3.2: - Adjust context - Keep calling clk_enable() directly] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
| * i2c-i801: Add Device IDs for Intel Lynx Point-LP PCHJames Ralston2012-09-192-0/+4
| | | | | | | | | | | | | | | | | | | | commit 4a8f1ddde942e232387e6129ce4f4c412e43802f upstream. Add the SMBus Device IDs for the Intel Lynx Point-LP PCH. Signed-off-by: James Ralston <james.d.ralston@intel.com> Signed-off-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
| * i2c-i801: Add device IDs for Intel Lynx PointSeth Heasley2012-09-192-0/+4
| | | | | | | | | | | | | | | | | | | | commit 062737fb6d90c632439b1f77ad6a4965cfc84a20 upstream. Add the SMBus controller device IDs for the Intel Lynx Point PCH. Signed-off-by: Seth Heasley <seth.heasley@intel.com> Signed-off-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
| * i2c-designware: Fix build error if CONFIG_I2C_DESIGNWARE_PLATFORM=y && ↵Axel Lin2012-09-193-2/+19
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | CONFIG_I2C_DESIGNWARE_PCI=y commit e68bb91baa0bb9817567bd45d560919e8e26373b upstream. This patch adds config I2C_DESIGNWARE_CORE in Kconfig, and let I2C_DESIGNWARE_PLATFORM and I2C_DESIGNWARE_PCI select I2C_DESIGNWARE_CORE. Because both I2C_DESIGNWARE_PLATFORM and I2C_DESIGNWARE_PCI can be built as built-in or module, we also need to export the functions in i2c-designware-core. This fixes below build error when CONFIG_I2C_DESIGNWARE_PLATFORM=y && CONFIG_I2C_DESIGNWARE_PCI=y: LD drivers/i2c/busses/built-in.o drivers/i2c/busses/i2c-designware-pci.o: In function `i2c_dw_clear_int': i2c-designware-core.c:(.text+0xa10): multiple definition of `i2c_dw_clear_int' drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x928): first defined here drivers/i2c/busses/i2c-designware-pci.o: In function `i2c_dw_init': i2c-designware-core.c:(.text+0x178): multiple definition of `i2c_dw_init' drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x90): first defined here drivers/i2c/busses/i2c-designware-pci.o: In function `dw_readl': i2c-designware-core.c:(.text+0xe8): multiple definition of `dw_readl' drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x0): first defined here drivers/i2c/busses/i2c-designware-pci.o: In function `i2c_dw_isr': i2c-designware-core.c:(.text+0x724): multiple definition of `i2c_dw_isr' drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x63c): first defined here drivers/i2c/busses/i2c-designware-pci.o: In function `i2c_dw_xfer': i2c-designware-core.c:(.text+0x4b0): multiple definition of `i2c_dw_xfer' drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x3c8): first defined here drivers/i2c/busses/i2c-designware-pci.o: In function `i2c_dw_is_enabled': i2c-designware-core.c:(.text+0x9d4): multiple definition of `i2c_dw_is_enabled' drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x8ec): first defined here drivers/i2c/busses/i2c-designware-pci.o: In function `dw_writel': i2c-designware-core.c:(.text+0x124): multiple definition of `dw_writel' drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x3c): first defined here drivers/i2c/busses/i2c-designware-pci.o: In function `i2c_dw_xfer_msg': i2c-designware-core.c:(.text+0x2e8): multiple definition of `i2c_dw_xfer_msg' drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x200): first defined here drivers/i2c/busses/i2c-designware-pci.o: In function `i2c_dw_enable': i2c-designware-core.c:(.text+0x9c8): multiple definition of `i2c_dw_enable' drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x8e0): first defined here drivers/i2c/busses/i2c-designware-pci.o: In function `i2c_dw_read_comp_param': i2c-designware-core.c:(.text+0xa24): multiple definition of `i2c_dw_read_comp_param' drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x93c): first defined here drivers/i2c/busses/i2c-designware-pci.o: In function `i2c_dw_disable': i2c-designware-core.c:(.text+0x9dc): multiple definition of `i2c_dw_disable' drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x8f4): first defined here drivers/i2c/busses/i2c-designware-pci.o: In function `i2c_dw_func': i2c-designware-core.c:(.text+0x710): multiple definition of `i2c_dw_func' drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x628): first defined here drivers/i2c/busses/i2c-designware-pci.o: In function `i2c_dw_disable_int': i2c-designware-core.c:(.text+0xa18): multiple definition of `i2c_dw_disable_int' drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x930): first defined here make[3]: *** [drivers/i2c/busses/built-in.o] Error 1 make[2]: *** [drivers/i2c/busses] Error 2 make[1]: *** [drivers/i2c] Error 2 make: *** [drivers] Error 2 Signed-off-by: Axel Lin <axel.lin@gmail.com> Signed-off-by: Jean Delvare <khali@linux-fr.org> Tested-by: Jiri Slaby <jslaby@suse.cz> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
| * i2c: davinci: Free requested IRQ in removeMarcus Folkesson2012-05-311-1/+1
| | | | | | | | | | | | | | | | | | | | | | commit 9868a060ccf769c08ec378a9829137e272e9a92c upstream. The freed IRQ is not necessary the one requested in probe. Even if it was, with two or more i2c-controllers it will fails anyway. Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com> Signed-off-by: Wolfram Sang <w.sang@pengutronix.de> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
| * i2c: tegra: notify transfer-complete after clearing status.Laxman Dewangan2012-05-311-7/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | commit c889e91d2cc22123f20f40dde0c0a91856a20eea upstream. The notification of the transfer complete by calling complete() should be done after clearing all interrupt status. This avoids the race condition of misconfigure the i2c controller in multi-core environment. Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com> Acked-by: Stephen Warren <swarren@wwwdotorg.org> Signed-off-by: Wolfram Sang <w.sang@pengutronix.de> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
| * i2c-eg20t: change timeout value 50msec to 1000msecTomoya MORINAGA2012-05-311-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | commit 8a52f9f347da721b199b7f9dcc0168bbe7d0baae upstream. Currently, during i2c works alone, wait-event timeout is not occurred. However, as CPU load increases, timeout occurs frequently. So, I modified like this patch. Modifying like this patch, I've never seen the timeout event with high load test. Signed-off-by: Tomoya MORINAGA <tomoya.rohm@gmail.com> Signed-off-by: Wolfram Sang <w.sang@pengutronix.de> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
| * i2c: pnx: Disable clk in suspendRoland Stigge2012-05-111-2/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | commit 6c557cfee08751d22aed34840f389b846f0f4508 upstream. In the driver's suspend function, clk_enable() was used instead of clk_disable(). This is corrected with this patch. Signed-off-by: Roland Stigge <stigge@antcom.de> Reviewed-by: Arnd Bergmann <arnd@arndb.de> [wsa: reworded commit header slightly] Signed-off-by: Wolfram Sang <w.sang@pengutronix.de> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
| * i2c-algo-bit: Fix spurious SCL timeouts under heavy loadVille Syrjala2012-03-191-1/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | commit 8ee161ce5e0cfc689eb677f227a6248191165fac upstream. When the system is under heavy load, there can be a significant delay between the getscl() and time_after() calls inside sclhi(). That delay may cause the time_after() check to trigger after SCL has gone high, causing sclhi() to return -ETIMEDOUT. To fix the problem, double check that SCL is still low after the timeout has been reached, before deciding to return -ETIMEDOUT. Signed-off-by: Ville Syrjala <syrjala@sci.fi> Signed-off-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| * i2c: mxs: only flag completion when queue is completely doneWolfram Sang2012-03-121-3/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | commit 844990daa2e69a4258049ba9c2bae1180657dac3 upstream. The hardware generates an interrupt for every completed command in the queue while the code assumed that it will only generate one interrupt when the queue is empty. So, explicitly check if the queue is really empty. This patch fixed problems which occurred due to high traffic on the bus. While we are here, move the completion-initialization after the parameter error checking. Signed-off-by: Wolfram Sang <w.sang@pengutronix.de> Cc: Shawn Guo <shawn.guo@linaro.org> Cc: Marek Vasut <marek.vasut@gmail.com> Cc: Lothar Waßmann <LW@KARO-electronics.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| * i2c-eg20t: modified the setting of transfer rate.Toshiharu Okada2012-01-251-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | commit ff35e8b18984ad2a82cbd259fc07f0be4b34b1aa upstream. This patch modified the setting value of I2C Bus Transfer Rate Setting Counter regisrer. Signed-off-by: Toshiharu Okada <toshiharu-linux@dsn.okisemi.com> Signed-off-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
| * I2C: OMAP: correct SYSC register offset for OMAP4Alexander Aring2012-01-251-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | commit 2727b1753934e154931d6b3bdf20c9b2398457a2 upstream. Correct OMAP_I2C_SYSC_REG offset in omap4 register map. Offset 0x20 is reserved and OMAP_I2C_SYSC_REG has 0x10 as offset. Signed-off-by: Alexander Aring <a.aring@phytec.de> [khilman@ti.com: minor changelog edits] Signed-off-by: Kevin Hilman <khilman@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
| * i2c: Fix error value returned by several bus driversJean Delvare2012-01-255-10/+20
| | | | | | | | | | | | | | | | | | | | | | | | | | commit 7c1f59c9d5caf3a84f35549b5d58f3c055a68da5 upstream. When adding checks for ACPI resource conflicts to many bus drivers, not enough attention was paid to the error paths, and for several drivers this causes 0 to be returned on error in some cases. Fix this by properly returning a non-zero value on every error. Signed-off-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
| * i2c-eg20t: correct the driver init order of pch_i2c_probe()Feng Tang2011-12-181-10/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Before registering an adapter to i2c subsystem, we need make sure driver is ready for incoming i2c xfer, becasue the i2c_add_adapter() may trigger a i2c device driver's proble function which may start some real i2c xfer. I met this issue when integrating a TSC2007 i2c touch screen device with the i2c-eg20t driver. This patch will call request_irq() and hw init before calling i2c_add_adapter(). Signed-off-by: Feng Tang <feng.tang@intel.com> Signed-off-by: Ben Dooks <ben-linux@fluff.org>
| * I2C: OMAP: fix FIFO usage for OMAP4Shubhrajyoti D2011-12-181-5/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | Currently the fifo depth is set to zero for OMAP4 which disables the FIFO usage. This patch enables the FIFO usage for I2C transactions on OMAP4 also. Tested on omap4430 and 3430. Tested-and-Reported-by: Nishanth Menon <nm@ti.com> Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com> Signed-off-by: Kevin Hilman <khilman@ti.com> Signed-off-by: Ben Dooks <ben-linux@fluff.org>
| * i2c-s3c2410: Fix return code of s3c24xx_i2c_parse_dt_gpioTushar Behera2011-12-181-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | s3c24xx_i2c_parse_dt_gpio is called when cfg_gpio is not defined in the platform data of the i2c device. When DT is not enabled, the above function always returns -EINVAL. Since there can be some i2c devices which don't need to configure any gpio lines, the probe of such devices would fail here. Changing the default return value to success would fix this issue. Signed-off-by: Tushar Behera <tushar.behera@linaro.org> Signed-off-by: Ben Dooks <ben-linux@fluff.org>
| * i2c: i2c-s3c2410: Add a cpu_relax() to busy wait for bus idleMark Brown2011-12-181-0/+1
| | | | | | | | | | | | | | Be a bit more friendly. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Ben Dooks <ben-linux@fluff.org>
| * Merge branch 'fixes' of ↵Linus Torvalds2011-12-011-1/+1
| |\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | http://ftp.arm.linux.org.uk/pub/linux/arm/kernel/git-cur/linux-2.6-arm * 'fixes' of http://ftp.arm.linux.org.uk/pub/linux/arm/kernel/git-cur/linux-2.6-arm: ARM: 7182/1: ARM cpu topology: fix warning ARM: 7181/1: Restrict kprobes probing SWP instructions to ARMv5 and below ARM: 7180/1: Change kprobes testcase with unpredictable STRD instruction ARM: 7177/1: GIC: avoid skipping non-existent PPIs in irq_start calculation ARM: 7176/1: cpu_pm: register GIC PM notifier only once ARM: 7175/1: add subname parameter to mfp_set_groupg callers ARM: 7174/1: Fix build error in kprobes test code on Thumb2 kernels ARM: 7172/1: dma: Drop GFP_COMP for DMA memory allocations ARM: 7171/1: unwind: add unwind directives to bitops assembly macros ARM: 7170/2: fix compilation breakage in entry-armv.S ARM: 7168/1: use cache type functions for arch_get_unmapped_area ARM: perf: check that we have a platform device when reserving PMU ARM: 7166/1: Use PMD_SHIFT instead of PGDIR_SHIFT in dma-consistent.c ARM: 7165/2: PL330: Fix typo in _prepare_ccr() ARM: 7163/2: PL330: Only register usable channels ARM: 7162/1: errata: tidy up Kconfig options for PL310 errata workarounds ARM: 7161/1: errata: no automatic store buffer drain ARM: perf: initialise used_mask for fake PMU during validation ARM: PMU: remove pmu_init declaration ARM: PMU: re-export release_pmu symbol to modules
| | * ARM: 7175/1: add subname parameter to mfp_set_groupg callersAxel Lin2011-11-261-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | commit 798681bf "ARM: 7158/1: add new MFP implement for NUC900" adds subname parameter for mfp_set_groupg. Thus add subname parameter to the callers. Signed-off-by: Axel Lin <axel.lin@gmail.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Wan Zongshun <mcuos.com@gmail.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
| * | i2c: Make i2cdev_notifier_call staticShubhrajyoti D2011-11-231-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The function i2cdev_notifier_call is used only in i2c-dev file making it static. Also removes the following sparse warning drivers/i2c/i2c-dev.c:582:5: warning: symbol 'i2cdev_notifier_call' was not declared. Should it be static? Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com> Signed-off-by: Jean Delvare <khali@linux-fr.org>
| * | i2c: Fix device name for 10-bit slave addressJean Delvare2011-11-231-1/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | 10-bit addresses overlap with traditional 7-bit addresses, leading in device name collisions. Add an arbitrary offset to 10-bit addresses to prevent this collision. The offset was chosen so that the address is still easily recognizable. Signed-off-by: Jean Delvare <khali@linux-fr.org> Acked-by: Wolfram Sang <w.sang@pengutronix.de>
| * | i2c-algo-bit: Generate correct i2c address sequence for 10-bit targetJeffrey (Sheng-Hui) Chu2011-11-231-2/+2
| |/ | | | | | | | | | | | | | | | | | | The wrong bits were put on the wire, fix that. This fixes kernel bug #42562. Signed-off-by: Sheng-Hui J. Chu <jeffchu@broadcom.com> Cc: stable@kernel.org Signed-off-by: Jean Delvare <khali@linux-fr.org>
| * Merge branch 'modsplit-Oct31_2011' of ↵Linus Torvalds2011-11-064-0/+4
| |\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux * 'modsplit-Oct31_2011' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux: (230 commits) Revert "tracing: Include module.h in define_trace.h" irq: don't put module.h into irq.h for tracking irqgen modules. bluetooth: macroize two small inlines to avoid module.h ip_vs.h: fix implicit use of module_get/module_put from module.h nf_conntrack.h: fix up fallout from implicit moduleparam.h presence include: replace linux/module.h with "struct module" wherever possible include: convert various register fcns to macros to avoid include chaining crypto.h: remove unused crypto_tfm_alg_modname() inline uwb.h: fix implicit use of asm/page.h for PAGE_SIZE pm_runtime.h: explicitly requires notifier.h linux/dmaengine.h: fix implicit use of bitmap.h and asm/page.h miscdevice.h: fix up implicit use of lists and types stop_machine.h: fix implicit use of smp.h for smp_processor_id of: fix implicit use of errno.h in include/linux/of.h of_platform.h: delete needless include <linux/module.h> acpi: remove module.h include from platform/aclinux.h miscdevice.h: delete unnecessary inclusion of module.h device_cgroup.h: delete needless include <linux/module.h> net: sch_generic remove redundant use of <linux/module.h> net: inet_timewait_sock doesnt need <linux/module.h> ... Fix up trivial conflicts (other header files, and removal of the ab3550 mfd driver) in - drivers/media/dvb/frontends/dibx000_common.c - drivers/media/video/{mt9m111.c,ov6650.c} - drivers/mfd/ab3550-core.c - include/linux/dmaengine.h
| | * i2c: Add module.h to modular files prev. implicitly getting itPaul Gortmaker2011-10-313-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | These files use interfaces from linux/module.h, so they must include that file to avoid build errors when the implicit presence of module.h is removed. [with i2c-pxa-pci.c fix from Randy Dunlap <rdunlap@xenotime.net>] Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
| | * i2c: add export.h to i2c-boardinfo.c for EXPORT_SYMBOLPaul Gortmaker2011-10-311-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | With module.h being implicitly everywhere via device.h, the absence of explicitly including something for EXPORT_SYMBOL went unnoticed. Since we are heading to fix things up and clean module.h from the device.h file, we need to explicitly include these files now. Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
| * | Merge branch 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linusLinus Torvalds2011-11-032-2/+2
| |\ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (37 commits) MIPS: O32: Provide definition of registers ta0 .. ta3. MIPS: perf: Add Octeon support for hardware perf. MIPS: perf: Add support for 64-bit perf counters. MIPS: perf: Reorganize contents of perf support files. MIPS: perf: Cleanup formatting in arch/mips/kernel/perf_event.c MIPS: Add accessor macros for 64-bit performance counter registers. MIPS: Add probes for more Octeon II CPUs. MIPS: Add more CPU identifiers for Octeon II CPUs. MIPS: XLR, XLS: Add comment for smp setup MIPS: JZ4740: GPIO: Check correct IRQ in demux handler MIPS: JZ4740: GPIO: Simplify IRQ demuxer MIPS: JZ4740: Use generic irq chip MIPS: Alchemy: remove all CONFIG_SOC_AU1??? defines MIPS: Alchemy: kill au1xxx.h header MIPS: Alchemy: clean DMA code of CONFIG_SOC_AU1??? defines MIPS, IDE: Alchem, au1xxx-ide: Remove pb1200/db1200 header dep MIPS: Alchemy: Redo PCI as platform driver MIPS: Alchemy: more base address cleanup MIPS: Alchemy: rewrite USB platform setup. MIPS: Alchemy: abstract USB block control register access ... Fix up trivial conflicts in: arch/mips/alchemy/devboards/db1x00/platform.c drivers/ide/Kconfig drivers/mmc/host/au1xmmc.c drivers/video/Kconfig sound/mips/Kconfig
| | * | MIPS: Alchemy: remove all CONFIG_SOC_AU1??? definesManuel Lauss2011-10-241-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Now that no driver any longer depends on the CONFIG_SOC_AU1??? symbols, it's time to get rid of them: Move some of the platform devices to the boards which can use them, Rename a few (unused) constants in the header, Replace them with MIPS_ALCHEMY in the various Kconfig files. Finally delete them altogether from the Alchemy Kconfig file. Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com> To: Linux-MIPS <linux-mips@linux-mips.org> Patchwork: https://patchwork.linux-mips.org/patch/2707/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
| | * | MIPS: Alchemy: kill au1xxx.h headerManuel Lauss2011-10-241-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | No longer required Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com> To: Linux-MIPS <linux-mips@linux-mips.org> Patchwork: https://patchwork.linux-mips.org/patch/2705/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org> delete mode 100644 arch/mips/include/asm/mach-au1x00/au1xxx.h
| * | | Merge branch 'for-next' of git://git.infradead.org/users/sameo/mfd-2.6Linus Torvalds2011-11-031-1/+0
| |\ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * 'for-next' of git://git.infradead.org/users/sameo/mfd-2.6: (80 commits) mfd: Fix missing abx500 header file updates mfd: Add missing <linux/io.h> include to intel_msic x86, mrst: add platform support for MSIC MFD driver mfd: Expose TurnOnStatus in ab8500 sysfs mfd: Remove support for early drop ab8500 chip mfd: Add support for ab8500 v3.3 mfd: Add ab8500 interrupt disable hook mfd: Convert db8500-prcmu panic() into pr_crit() mfd: Refactor db8500-prcmu request_clock() function mfd: Rename db8500-prcmu init function mfd: Fix db5500-prcmu defines mfd: db8500-prcmu voltage domain consumers additions mfd: db8500-prcmu reset code retrieval mfd: db8500-prcmu tweak for modem wakeup mfd: Add db8500-pcmu watchdog accessor functions for watchdog mfd: hwacc power state db8500-prcmu accessor mfd: Add db8500-prcmu accessors for PLL and SGA clock mfd: Move to the new db500 PRCMU API mfd: Create a common interface for dbx500 PRCMU drivers mfd: Initialize DB8500 PRCMU regs ... Fix up trivial conflicts in arch/arm/mach-imx/mach-mx31moboard.c arch/arm/mach-omap2/board-omap3beagle.c arch/arm/mach-u300/include/mach/irqs.h drivers/mfd/wm831x-spi.c
| | * | | mfd: remove CONFIG_MFD_SUPPORTArnd Bergmann2011-10-241-1/+0
| | |/ / | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | We currently have two symbols to control compilation the MFD subsystem, MFD_SUPPORT and MFD_CORE. The MFD_SUPPORT is actually not required at all, it only hides the submenu when not set, with the effect that Kconfig warns about missing dependencies when another driver selects an MFD driver while MFD_SUPPORT is disabled. Turning the MFD submenu back from menuconfig into a plain menu simplifies the Kconfig syntax for those kinds of users and avoids the surprise when the menu suddenly appears because another driver was enabled that selects this symbol. Signed-off-by: Arnd Bergmann <arnd@arndb.de>
| * | | Merge branch 'for-linus/i2c-3.2' of git://git.fluff.org/bjdooks/linuxLinus Torvalds2011-11-0120-664/+1450
| |\ \ \ | | |_|/ | |/| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * 'for-linus/i2c-3.2' of git://git.fluff.org/bjdooks/linux: (47 commits) i2c-s3c2410: Add device tree support i2c-s3c2410: Keep a copy of platform data and use it i2c-nomadik: cosmetic coding style corrections i2c-au1550: dev_pm_ops conversion i2c-au1550: increase timeout waiting for master done i2c-au1550: remove unused ack_timeout i2c-au1550: remove usage of volatile keyword i2c-tegra: __iomem annotation fix i2c-eg20t: Add initialize processing in case i2c-error occurs i2c-eg20t: Fix flag setting issue i2c-eg20t: add stop sequence in case wait-event timeout occurs i2c-eg20t: Separate error processing i2c-eg20t: Fix 10bit access issue i2c-eg20t: Modify returned value s32 to long i2c-eg20t: Fix bus-idle waiting issue i2c-designware: Fix PCI core warning on suspend/resume i2c-designware: Add runtime power management support i2c-designware: Add support for Designware core behind PCI devices. i2c-designware: Push all register reads/writes into the core code. i2c-designware: Support multiple cores using same ISR ...
| | | |
| | | \
| | | \
| | | \
| | *---. \ Merge branches 'for-32/i2c/nomadik', 'for-32/i2c/s3c2410-dt' and ↵Ben Dooks2011-11-013-52/+167
| | |\ \ \ \ | | | | | | | | | | | | | | | | | | | | | 'for-32/i2c/tegra-iomem' into for-linus/i2c-3.2
| | | | | * | i2c-tegra: __iomem annotation fixOlof Johansson2011-10-291-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | drivers/i2c/busses/i2c-tegra.c:585:7: warning: incorrect type in assignment (different address spaces) drivers/i2c/busses/i2c-tegra.c:585:7: expected void *base drivers/i2c/busses/i2c-tegra.c:585:7: got void [noderef] <asn:2>* drivers/i2c/busses/i2c-tegra.c:619:16: warning: incorrect type in assignment (different address spaces) drivers/i2c/busses/i2c-tegra.c:619:16: expected void [noderef] <asn:2>*base drivers/i2c/busses/i2c-tegra.c:619:16: got void *base drivers/i2c/busses/i2c-tegra.c:689:10: warning: incorrect type in argument 1 (different address spaces) drivers/i2c/busses/i2c-tegra.c:689:10: expected void volatile [noderef] <asn:2>*addr drivers/i2c/busses/i2c-tegra.c:689:10: got void *base Signed-off-by: Olof Johansson <olof@lixom.net> Acked-by; Stephen Warren <swarren@nvidia.com> Signed-off-by: Ben Dooks <ben-linux@fluff.org>
| | | | * | | i2c-s3c2410: Add device tree supportThomas Abraham2011-10-291-4/+106
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add device tree probe support for Samsung's s3c2410 i2c driver. Cc: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org> Acked-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: Ben Dooks <ben-linux@fluff.org>
| | | | * | | i2c-s3c2410: Keep a copy of platform data and use itThomas Abraham2011-10-291-4/+14
| | | | |/ / | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The platform data is copied into driver's private data and the copy is used for all access to the platform data. This simpifies the addition of device tree support for the i2c-s3c2410 driver. Cc: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org> Acked-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: Ben Dooks <ben-linux@fluff.org>
| | | * | | i2c-nomadik: cosmetic coding style correctionsJonas Aaberg2011-10-291-43/+46
| | | |/ / | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This fixes a number of whitespace and punctuation problems around the Nomadik I2C driver. Signed-off-by: Jonas Aaberg <jonas.aberg@stericsson.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Ben Dooks <ben-linux@fluff.org>
| | * | | Merge branch 'for-32/i2c/irqflags' into for-linus/i2c-3.2Ben Dooks2011-11-019-10/+10
| | |\ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Conflicts: drivers/i2c/busses/i2c-designware-core.c Fixed up merge conflic
| | | * | | i2c: irq: Remove IRQF_DISABLEDYong Zhang2011-10-2910-11/+11
| | | |/ / | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Since commit [c58543c8: genirq: Run irq handlers with interrupts disabled], We run all interrupt handlers with interrupts disabled and we even check and yell when an interrupt handler returns with interrupts enabled (see commit [b738a50a: genirq: Warn when handler enables interrupts]). So now this flag is a NOOP and can be removed. Signed-off-by: Yong Zhang <yong.zhang0@gmail.com> Acked-by: Wolfram Sang <w.sang@pengutronix.de> Acked-by: Linus Walleij <linus.walleij@linaro.org> Acked-by: Barry Song <21cnbao@gmail.com> Signed-off-by: Ben Dooks <ben-linux@fluff.org>
| | | | |
| | | \ \
| | | \ \
| | | \ \
| | | \ \
| | | \ \
| | *-----. \ \ Merge branches 'for-32/i2c/omap-v4', 'for-32/i2c/imx-dt', ↵Ben Dooks2011-11-019-530/+1181
| | |\ \ \ \ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | 'for-32/i2c/eg20t-v4', 'for-32/i2c/designware-v5' and 'for-32/i2c/au1550' into for-linus/i2c-3.2
| | | | | | * | | i2c-au1550: dev_pm_ops conversionManuel Lauss2011-10-291-10/+14
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | use newer dev_pm_ops for PM Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com> Signed-off-by: Ben Dooks <ben-linux@fluff.org>
| | | | | | * | | i2c-au1550: increase timeout waiting for master doneManuel Lauss2011-10-291-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Double the timeout in the loop which busy-waits for the "master-done" bit to be set. This bit indicates whether an i2c transaction has completed; on the DB1300 and DB1550 boards this timeout is slightly too short and causes transactions to the WM8731 codec to be falsely flagged as failed. The timeout itself is necessary since transactions to non-existant slaves never set this bit in the first place (and cause i2cdetect to hang). With this change the WM8731 codec on the DB1300/DB1550 boards is correctly detected and initialized. Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com> Signed-off-by: Ben Dooks <ben-linux@fluff.org>
| | | | | | * | | i2c-au1550: remove unused ack_timeoutManuel Lauss2011-10-291-2/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The ack_timeout context member is unused, get rid of it. Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com> Signed-off-by: Ben Dooks <ben-linux@fluff.org>
generated by cgit v1.1 at 2024-09-22 17:01:46 +0000