| Commit message (Collapse) | Author | Age | Files | Lines |
|---|
| | |
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This patch fixes the value of FIFO_CTRL in MSCTRL.
Main-scaler has the value to specify a basis FIFO control of input DMA.
The description of FIFO_CTRL has been changed as below.
0 = FIFO Empty (Next burst transaction is possible when FIFO is empty)
1 = FIFO Full (Next burst transaction is possible except Full FIFO)
Value '1' is recommended to enhance the FIMC operation performance.
Reviewed-by: Jonghun Han <jonghun.han@samsung.com>
Signed-off-by: Hyunwoong Kim <khw0178.kim@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The main scaler has four SFRs for main scaler ratio depending on FIMC version.
FIMC 4.x has only two SFRs and FIMC 5.x has four SFRs for main scaler.
Those are MainHorRatio, MainHorRatio_ext, MainVerRatio and MainverRatio_ext.
The FIMC 5.x has 15 bit resolution for scaling ratio as below.
{MainHorRatio,MainHorRatio_ext} = {[14:6],[5:0]}.
{MainVerRatio,MainVerRatio_ext} = {[14:6],[5:0]}.
MainHorRatio = CISCCTRL[24:16], MainHorRatio_ext = CIEXTEN[15:10]
MainVerRatio = CISCCTRL[8:0], MainVerRatio_ext = CIEXTEN[5:0]
This patch supports FIMC 4.x and FIMC 5.x using platform_device_id::driver_data.
Reviewed-by: Jonghun Han <jonghun.han@samsung.com>
Signed-off-by: Hyunwoong Kim <khw0178.kim@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
| |
|
|
|
|
|
|
|
|
| |
Some color formats are mismatched in s5p-fimc driver.
CIOCTRL[1:0], order422_out, should be set 2b'00 not 2b'11
to use V4L2_PIX_FMT_YUYV. Because in V4L2 standard V4L2_PIX_FMT_YUYV means
"start + 0: Y'00 Cb00 Y'01 Cr00 Y'02 Cb01 Y'03 Cr01". According to datasheet
2b'00 is right value for V4L2_PIX_FMT_YUYV.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
| |
|
|
|
|
|
|
|
| |
Increase the input DMA "successive burst count" to default
value 4 to improve DMA performance. Minor cleanup.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
| |
|
|
|
|
|
|
|
|
|
| |
FIMC IP in S5Pv310 series has extended DMA status registers
and some bit fields are marked as reserved comparing to S5PC100/110.
Use correct registers for getting DMA write pointer in each SoC variant
supported by the driver.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
| |
|
|
|
|
|
|
|
|
| |
Enable FIMC operation on S5PC210 (S5PV310) SoCs. This a minimal
adaptation to obtain functionality of older FIMC IP revisions
(S5PC100, S5PC110) on S5PC210 SOcs.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
| |
|
|
|
|
|
|
|
| |
Add MIPI CSI format definitions, prepare DMA address
definitions for interlaced input frame mode.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
|
This driver exports a video device node per each camera interface/
video postprocessor (FIMC) device contained in Samsung S5P SoC series.
The driver is based on v4l2-mem2mem framework.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Pawel Osciak <p.osciak@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
