| Commit message (Collapse) | Author | Age | Files | Lines |
|\ |
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
commit 8f2777f53e3d5ad8ef2a176a4463a5c8e1a16431 upstream.
Since fc_fcp_cleanup_cmd() can sleep this function must not
be called while holding a spinlock. This patch avoids that
fc_fcp_cleanup_each_cmd() triggers the following bug:
BUG: scheduling while atomic: sg_reset/1512/0x00000202
1 lock held by sg_reset/1512:
#0: (&(&fsp->scsi_pkt_lock)->rlock){+.-...}, at: [<ffffffffc0225cd5>] fc_fcp_cleanup_each_cmd.isra.21+0xa5/0x150 [libfc]
Preemption disabled at:[<ffffffffc0225cd5>] fc_fcp_cleanup_each_cmd.isra.21+0xa5/0x150 [libfc]
Call Trace:
[<ffffffff816c612c>] dump_stack+0x4f/0x7b
[<ffffffff810828bc>] __schedule_bug+0x6c/0xd0
[<ffffffff816c87aa>] __schedule+0x71a/0xa10
[<ffffffff816c8ad2>] schedule+0x32/0x80
[<ffffffffc0217eac>] fc_seq_set_resp+0xac/0x100 [libfc]
[<ffffffffc0218b11>] fc_exch_done+0x41/0x60 [libfc]
[<ffffffffc0225cff>] fc_fcp_cleanup_each_cmd.isra.21+0xcf/0x150 [libfc]
[<ffffffffc0225f43>] fc_eh_device_reset+0x1c3/0x270 [libfc]
[<ffffffff814a2cc9>] scsi_try_bus_device_reset+0x29/0x60
[<ffffffff814a3908>] scsi_ioctl_reset+0x258/0x2d0
[<ffffffff814a2650>] scsi_ioctl+0x150/0x440
[<ffffffff814b3a9d>] sd_ioctl+0xad/0x120
[<ffffffff8132f266>] blkdev_ioctl+0x1b6/0x810
[<ffffffff811da608>] block_ioctl+0x38/0x40
[<ffffffff811b4e08>] do_vfs_ioctl+0x2f8/0x530
[<ffffffff811b50c1>] SyS_ioctl+0x81/0xa0
[<ffffffff816cf8b2>] system_call_fastpath+0x16/0x7a
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
commit 660d0831d1494a6837b2f810d08b5be092c1f31d upstream.
In case of hw iscsi offload, an host can have N-number of active
connections. There can be IO's running on some connections which
make host->host_busy always TRUE. Now if logout from a connection
is tried then the code gets into an infinite loop as host->host_busy
is always TRUE.
iscsi_conn_teardown(....)
{
.........
/*
* Block until all in-progress commands for this connection
* time out or fail.
*/
for (;;) {
spin_lock_irqsave(session->host->host_lock, flags);
if (!atomic_read(&session->host->host_busy)) { /* OK for ERL == 0 */
spin_unlock_irqrestore(session->host->host_lock, flags);
break;
}
spin_unlock_irqrestore(session->host->host_lock, flags);
msleep_interruptible(500);
iscsi_conn_printk(KERN_INFO, conn, "iscsi conn_destroy(): "
"host_busy %d host_failed %d\n",
atomic_read(&session->host->host_busy),
session->host->host_failed);
................
...............
}
}
This is not an issue with software-iscsi/iser as each cxn is a separate
host.
Fix:
Acquiring eh_mutex in iscsi_conn_teardown() before setting
session->state = ISCSI_STATE_TERMINATE.
Signed-off-by: John Soni Jose <sony.john@avagotech.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Reviewed-by: Chris Leech <cleech@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
commit 45c44b5ff9caa743ed9c2bfd44307c536c9caf1e upstream.
Increase the default init stage change timeout from 15 seconds to 30 seconds.
This resolves issues we have seen with some adapters not transitioning
to the first init stage within 15 seconds, which results in adapter
initialization failures.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
commit 74856fbf441929918c49ff262ace9835048e4e6a upstream.
256 bytes per sector support has been broken since 2.6.X,
and no-one stepped up to fix this.
So disable support for it.
Signed-off-by: Mark Hounschell <dmarkh@cfl.rr.com>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
commit 118c855b5623f3e2e6204f02623d88c09e0c34de upstream.
The 3w-9xxx driver needs to tear down the dma mappings before returning
the command to the midlayer, as there is no guarantee the sglist and
count are valid after that point. Also remove the dma mapping helpers
which have another inherent race due to the request_id index.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
commit 9cd9554615cba14f0877cc9972a6537ad2bdde61 upstream.
The 3w-xxxx driver needs to tear down the dma mappings before returning
the command to the midlayer, as there is no guarantee the sglist and
count are valid after that point. Also remove the dma mapping helpers
which have another inherent race due to the request_id index.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
commit 579d69bc1fd56d5af5761969aa529d1d1c188300 upstream.
The 3w-sas driver needs to tear down the dma mappings before returning
the command to the midlayer, as there is no guarantee the sglist and
count are valid after that point. Also remove the dma mapping helpers
which have another inherent race due to the request_id index.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reported-by: Torsten Luettgert <ml-lkml@enda.eu>
Tested-by: Bernd Kardatzki <Bernd.Kardatzki@med.uni-tuebingen.de>
Acked-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
commit 16b8528d20607925899b1df93bfd8fbab98d267c upstream.
We only want to steer the I/O completion towards a queue, but don't
actually access any per-CPU data, so the raw_ version is fine to use
and avoids the warnings when using smp_processor_id().
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reported-by: Andy Lutomirski <luto@kernel.org>
Tested-by: Andy Lutomirski <luto@kernel.org>
Acked-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
[bwh: Backported to 3.2: drop changes to megasas_build_dcdb_fusion()]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
commit 451a2886b6bf90e2fb378f7c46c655450fb96e81 upstream.
unfortunately, allowing an arbitrary 16bit value means a possibility of
overflow in the calculation of total number of pages in bio_map_user_iov() -
we rely on there being no more than PAGE_SIZE members of sum in the
first loop there. If that sum wraps around, we end up allocating
too small array of pointers to pages and it's easy to overflow it in
the second loop.
X-Coverup: TINC (and there's no lumber cartel either)
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
[bwh: s/MAX_UIOVEC/UIO_MAXIOV/. This was fixed upstream by commit
fdc81f45e9f5 ("sg_start_req(): use import_iovec()"), but we don't have
that function.]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
commit bba0bdd7ad4713d82338bcd9b72d57e9335a664b upstream.
SCSI transport drivers and SCSI LLDs block a SCSI device if the
transport layer is not operational. This means that in this state
no requests should be processed, even if the REQ_PREEMPT flag has
been set. This patch avoids that a rescan shortly after a cable
pull sporadically triggers the following kernel oops:
BUG: unable to handle kernel paging request at ffffc9001a6bc084
IP: [<ffffffffa04e08f2>] mlx4_ib_post_send+0xd2/0xb30 [mlx4_ib]
Process rescan-scsi-bus (pid: 9241, threadinfo ffff88053484a000, task ffff880534aae100)
Call Trace:
[<ffffffffa0718135>] srp_post_send+0x65/0x70 [ib_srp]
[<ffffffffa071b9df>] srp_queuecommand+0x1cf/0x3e0 [ib_srp]
[<ffffffffa0001ff1>] scsi_dispatch_cmd+0x101/0x280 [scsi_mod]
[<ffffffffa0009ad1>] scsi_request_fn+0x411/0x4d0 [scsi_mod]
[<ffffffff81223b37>] __blk_run_queue+0x27/0x30
[<ffffffff8122a8d2>] blk_execute_rq_nowait+0x82/0x110
[<ffffffff8122a9c2>] blk_execute_rq+0x62/0xf0
[<ffffffffa000b0e8>] scsi_execute+0xe8/0x190 [scsi_mod]
[<ffffffffa000b2f3>] scsi_execute_req+0xa3/0x130 [scsi_mod]
[<ffffffffa000c1aa>] scsi_probe_lun+0x17a/0x450 [scsi_mod]
[<ffffffffa000ce86>] scsi_probe_and_add_lun+0x156/0x480 [scsi_mod]
[<ffffffffa000dc2f>] __scsi_scan_target+0xdf/0x1f0 [scsi_mod]
[<ffffffffa000dfa3>] scsi_scan_host_selected+0x183/0x1c0 [scsi_mod]
[<ffffffffa000edfb>] scsi_scan+0xdb/0xe0 [scsi_mod]
[<ffffffffa000ee13>] store_scan+0x13/0x20 [scsi_mod]
[<ffffffff811c8d9b>] sysfs_write_file+0xcb/0x160
[<ffffffff811589de>] vfs_write+0xce/0x140
[<ffffffff81158b53>] sys_write+0x53/0xa0
[<ffffffff81464592>] system_call_fastpath+0x16/0x1b
[<00007f611c9d9300>] 0x7f611c9d92ff
Reported-by: Max Gurtuvoy <maxg@mellanox.com>
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
commit 2e7cee027b26cbe7e6685a7a14bd2850bfe55d33 upstream.
Kernel panic was happening as iscsi_host_remove() was called on
a host which was not yet added.
Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
commit 6302ce4d80aa82b3fdb5c5cd68e7268037091b47 upstream.
This crash was reported:
[ 366.947370] sd 3:0:1:0: [sdb] Spinning up disk....
[ 368.804046] BUG: unable to handle kernel NULL pointer dereference at (null)
[ 368.804072] IP: [<ffffffff81358457>] __mutex_lock_common.isra.7+0x9c/0x15b
[ 368.804098] PGD 0
[ 368.804114] Oops: 0002 [#1] SMP
[ 368.804143] CPU 1
[ 368.804151] Modules linked in: sg netconsole s3g(PO) uinput joydev hid_multitouch usbhid hid snd_hda_codec_via cpufreq_userspace cpufreq_powersave cpufreq_stats uhci_hcd cpufreq_conservative snd_hda_intel snd_hda_codec snd_hwdep snd_pcm sdhci_pci snd_page_alloc sdhci snd_timer snd psmouse evdev serio_raw pcspkr soundcore xhci_hcd shpchp s3g_drm(O) mvsas mmc_core ahci libahci drm i2c_core acpi_cpufreq mperf video processor button thermal_sys dm_dmirror exfat_fs exfat_core dm_zcache dm_mod padlock_aes aes_generic padlock_sha iscsi_target_mod target_core_mod configfs sswipe libsas libata scsi_transport_sas picdev via_cputemp hwmon_vid fuse parport_pc ppdev lp parport autofs4 ext4 crc16 mbcache jbd2 sd_mod crc_t10dif usb_storage scsi_mod ehci_hcd usbcore usb_common
[ 368.804749]
[ 368.804764] Pid: 392, comm: kworker/u:3 Tainted: P W O 3.4.87-logicube-ng.22 #1 To be filled by O.E.M. To be filled by O.E.M./EPIA-M920
[ 368.804802] RIP: 0010:[<ffffffff81358457>] [<ffffffff81358457>] __mutex_lock_common.isra.7+0x9c/0x15b
[ 368.804827] RSP: 0018:ffff880117001cc0 EFLAGS: 00010246
[ 368.804842] RAX: 0000000000000000 RBX: ffff8801185030d0 RCX: ffff88008edcb420
[ 368.804857] RDX: 0000000000000000 RSI: 0000000000000002 RDI: ffff8801185030d4
[ 368.804873] RBP: ffff8801181531c0 R08: 0000000000000020 R09: 00000000fffffffe
[ 368.804885] R10: 0000000000000000 R11: 0000000000000000 R12: ffff8801185030d4
[ 368.804899] R13: 0000000000000002 R14: ffff880117001fd8 R15: ffff8801185030d8
[ 368.804916] FS: 0000000000000000(0000) GS:ffff88011fc80000(0000) knlGS:0000000000000000
[ 368.804931] CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b
[ 368.804946] CR2: 0000000000000000 CR3: 000000000160b000 CR4: 00000000000006e0
[ 368.804962] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 368.804978] DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
[ 368.804995] Process kworker/u:3 (pid: 392, threadinfo ffff880117000000, task ffff8801181531c0)
[ 368.805009] Stack:
[ 368.805017] ffff8801185030d8 0000000000000000 ffffffff8161ddf0 ffffffff81056f7c
[ 368.805062] 000000000000b503 ffff8801185030d0 ffff880118503000 0000000000000000
[ 368.805100] ffff8801185030d0 ffff8801188b8000 ffff88008edcb420 ffffffff813583ac
[ 368.805135] Call Trace:
[ 368.805153] [<ffffffff81056f7c>] ? up+0xb/0x33
[ 368.805168] [<ffffffff813583ac>] ? mutex_lock+0x16/0x25
[ 368.805194] [<ffffffffa018c414>] ? smp_execute_task+0x4e/0x222 [libsas]
[ 368.805217] [<ffffffffa018ce1c>] ? sas_find_bcast_dev+0x3c/0x15d [libsas]
[ 368.805240] [<ffffffffa018ce4f>] ? sas_find_bcast_dev+0x6f/0x15d [libsas]
[ 368.805264] [<ffffffffa018e989>] ? sas_ex_revalidate_domain+0x37/0x2ec [libsas]
[ 368.805280] [<ffffffff81355a2a>] ? printk+0x43/0x48
[ 368.805296] [<ffffffff81359a65>] ? _raw_spin_unlock_irqrestore+0xc/0xd
[ 368.805318] [<ffffffffa018b767>] ? sas_revalidate_domain+0x85/0xb6 [libsas]
[ 368.805336] [<ffffffff8104e5d9>] ? process_one_work+0x151/0x27c
[ 368.805351] [<ffffffff8104f6cd>] ? worker_thread+0xbb/0x152
[ 368.805366] [<ffffffff8104f612>] ? manage_workers.isra.29+0x163/0x163
[ 368.805382] [<ffffffff81052c4e>] ? kthread+0x79/0x81
[ 368.805399] [<ffffffff8135fea4>] ? kernel_thread_helper+0x4/0x10
[ 368.805416] [<ffffffff81052bd5>] ? kthread_flush_work_fn+0x9/0x9
[ 368.805431] [<ffffffff8135fea0>] ? gs_change+0x13/0x13
[ 368.805442] Code: 83 7d 30 63 7e 04 f3 90 eb ab 4c 8d 63 04 4c 8d 7b 08 4c 89 e7 e8 fa 15 00 00 48 8b 43 10 4c 89 3c 24 48 89 63 10 48 89 44 24 08 <48> 89 20 83 c8 ff 48 89 6c 24 10 87 03 ff c8 74 35 4d 89 ee 41
[ 368.805851] RIP [<ffffffff81358457>] __mutex_lock_common.isra.7+0x9c/0x15b
[ 368.805877] RSP <ffff880117001cc0>
[ 368.805886] CR2: 0000000000000000
[ 368.805899] ---[ end trace b720682065d8f4cc ]---
It's directly caused by 89d3cf6 [SCSI] libsas: add mutex for SMP task
execution, but shows a deeper cause: expander functions expect to be able to
cast to and treat domain devices as expanders. The correct fix is to only do
expander discover when we know we've got an expander device to avoid wrongly
casting a non-expander device.
Reported-by: Praveen Murali <pmurali@logicube.com>
Tested-by: Praveen Murali <pmurali@logicube.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
[bwh: Backported to 3.2:
- Adjust context
- Use sas_dev_type enumerators rather than sas_device_type enumerators]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
commit 3b524a683af8991b4eab4182b947c65f0ce1421b upstream.
Fix SCSI generic read() incorrectly returning success after detecting an
error.
Signed-off-by: Tony Battersby <tonyb@cybernetics.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
gather segment boundary limit.
commit f76a610a8b4b6280eaedf48f3af9d5d74e418b66 upstream.
In reference to bug https://bugzilla.redhat.com/show_bug.cgi?id=1097141
Assert is seen with AMD cpu whenever calling pci_alloc_consistent.
[ 29.406183] ------------[ cut here ]------------
[ 29.410505] kernel BUG at lib/iommu-helper.c:13!
Signed-off-by: Minh Tran <minh.tran@emulex.com>
Fixes: 6733b39a1301b0b020bbcbf3295852e93e624cb1
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
commit b6c92b7e0af575e2b8b05bdf33633cf9e1661cbf upstream.
The .eh_abort_handler needs to return SUCCESS, FAILED, or
FAST_IO_FAIL. So fixup all callers to adhere to this requirement.
Reviewed-by: Robert Elliott <elliott@hp.com>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
[bwh: Backported to 3.2: drop changes to esas2r]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
commit 2cc5bfaf854463d9d1aa52091f60110fbf102a96 upstream.
When the driver calls scsi_done and after that frees it's internal
preallocated memory it can happen that a new job is enqueud before
the memory is freed. The allocation fails and the message
"cmd_alloc returned NULL" is shown.
Patch below fixes it by moving cmd->scsi_done after cmd_free.
Signed-off-by: Tomas Henzl <thenzl@redhat.com>
Acked-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Cc: Masoud Sharbiani <msharbiani@twopensource.com>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
commit 01a4cc4d0cd6a836c7b923760e8eb1cbb6a47258 upstream.
In some cases, the fcoe_rx_list may contains multiple instances
of the same skb (the so called "shared skbs").
the bnx2fc_l2_rcv thread is a loop that extracts a skb from the list,
modifies (and destroys) its content and then proceed to the next one.
The problem is that if the skb is shared, the remaining instances will
be corrupted.
The solution is to use skb_share_check() before adding the skb to the
fcoe_rx_list.
[ 6286.808725] ------------[ cut here ]------------
[ 6286.808729] WARNING: at include/scsi/fc_frame.h:173 bnx2fc_l2_rcv_thread+0x425/0x450 [bnx2fc]()
[ 6286.808748] Modules linked in: bnx2x(-) mdio dm_service_time bnx2fc cnic uio fcoe libfcoe 8021q garp stp mrp libfc llc scsi_transport_fc scsi_tgt sg iTCO_wdt iTCO_vendor_support coretemp kvm_intel kvm crct10dif_pclmul crc32_pclmul crc32c_intel e1000e ghash_clmulni_intel aesni_intel lrw gf128mul glue_helper ablk_helper ptp cryptd hpilo serio_raw hpwdt lpc_ich pps_core ipmi_si pcspkr mfd_core ipmi_msghandler shpchp pcc_cpufreq mperf nfsd auth_rpcgss nfs_acl lockd sunrpc dm_multipath xfs libcrc32c ata_generic pata_acpi sd_mod crc_t10dif crct10dif_common mgag200 syscopyarea sysfillrect sysimgblt i2c_algo_bit ata_piix drm_kms_helper ttm drm libata i2c_core hpsa dm_mirror dm_region_hash dm_log dm_mod [last unloaded: mdio]
[ 6286.808750] CPU: 3 PID: 1304 Comm: bnx2fc_l2_threa Not tainted 3.10.0-121.el7.x86_64 #1
[ 6286.808750] Hardware name: HP ProLiant DL120 G7, BIOS J01 07/01/2013
[ 6286.808752] 0000000000000000 000000000b36e715 ffff8800deba1e00 ffffffff815ec0ba
[ 6286.808753] ffff8800deba1e38 ffffffff8105dee1 ffffffffa05618c0 ffff8801e4c81888
[ 6286.808754] ffffe8ffff663868 ffff8801f402b180 ffff8801f56bc000 ffff8800deba1e48
[ 6286.808754] Call Trace:
[ 6286.808759] [<ffffffff815ec0ba>] dump_stack+0x19/0x1b
[ 6286.808762] [<ffffffff8105dee1>] warn_slowpath_common+0x61/0x80
[ 6286.808763] [<ffffffff8105e00a>] warn_slowpath_null+0x1a/0x20
[ 6286.808765] [<ffffffffa054f415>] bnx2fc_l2_rcv_thread+0x425/0x450 [bnx2fc]
[ 6286.808767] [<ffffffffa054eff0>] ? bnx2fc_disable+0x90/0x90 [bnx2fc]
[ 6286.808769] [<ffffffff81085aef>] kthread+0xcf/0xe0
[ 6286.808770] [<ffffffff81085a20>] ? kthread_create_on_node+0x140/0x140
[ 6286.808772] [<ffffffff815fc76c>] ret_from_fork+0x7c/0xb0
[ 6286.808773] [<ffffffff81085a20>] ? kthread_create_on_node+0x140/0x140
[ 6286.808774] ---[ end trace c6cdb939184ccb4e ]---
Signed-off-by: Maurizio Lombardi <mlombard@redhat.com>
Acked-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
commit 48379270fe6808cf4612ee094adc8da2b7a83baa upstream.
Setups that use the blk-mq I/O path can lock up if a host with a single
device that has its door locked enters EH. Make sure to only send the
command to re-lock the door to devices that actually were reset and thus
might have lost their state. Otherwise the EH code might be get blocked
on blk_get_request as all requests for non-reset devices might be in use.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reported-by: Meelis Roos <meelis.roos@ut.ee>
Tested-by: Meelis Roos <meelis.roos@ut.ee>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
commit db9bfd64b14a3a8f1868d2164518fdeab1b26ad1 upstream.
This patches fixes a potential buffer overrun in __iscsi_conn_send_pdu.
This function is used by iscsi drivers and userspace to send iscsi PDUs/
commands. For login commands, we have a set buffer size. For all other
commands we do not support data buffers.
This was reported by Dan Carpenter here:
http://www.spinics.net/lists/linux-scsi/msg66838.html
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
commit 0758f4f732b08b6ef07f2e5f735655cf69fea477 upstream.
When copy_from_user fails, return -EFAULT, not -ENOMEM
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Reported-by: Robert Elliott <elliott@hp.com>
Reviewed-by: Joe Handzik <joseph.t.handzik@hp.com>
Reviewed-by: Scott Teel <scott.teel@hp.com>
Reviewed by: Mike MIller <michael.miller@canonical.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
commit 03a6c3ff3282ee9fa893089304d951e0be93a144 upstream.
bfa_swap_words() shifts its argument (assumed to be 64-bit) by 32 bits
each way. In two places the argument type is dma_addr_t, which may be
32-bit, in which case the effect of the bit shift is undefined:
drivers/scsi/bfa/bfa_fcpim.c: In function 'bfa_ioim_send_ioreq':
drivers/scsi/bfa/bfa_fcpim.c:2497:4: warning: left shift count >= width of type [enabled by default]
addr = bfa_sgaddr_le(sg_dma_address(sg));
^
drivers/scsi/bfa/bfa_fcpim.c:2497:4: warning: right shift count >= width of type [enabled by default]
drivers/scsi/bfa/bfa_fcpim.c:2509:4: warning: left shift count >= width of type [enabled by default]
addr = bfa_sgaddr_le(sg_dma_address(sg));
^
drivers/scsi/bfa/bfa_fcpim.c:2509:4: warning: right shift count >= width of type [enabled by default]
Avoid this by adding casts to u64 in bfa_swap_words().
Compile-tested only.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: Anil Gurumurthy <anil.gurumurthy@qlogic.com>
Fixes: f16a17507b09 ('[SCSI] bfa: remove all OS wrappers')
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
commit 89fb4cd1f717a871ef79fa7debbe840e3225cd54 upstream.
Flush commands don't transfer data and thus need to be special cased
in the I/O completion handler so that we can propagate errors to
the block layer and filesystem.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Reported-by: Steven Haber <steven@qumulo.com>
Tested-by: Steven Haber <steven@qumulo.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
commit fd1232b214af43a973443aec6a2808f16ee5bf70 upstream.
This patch fixes I/O errors with the sym53c8xx_2 driver when the disk
returns QUEUE FULL status.
When the controller encounters an error (including QUEUE FULL or BUSY
status), it aborts all not yet submitted requests in the function
sym_dequeue_from_squeue.
This function aborts them with DID_SOFT_ERROR.
If the disk has full tag queue, the request that caused the overflow is
aborted with QUEUE FULL status (and the scsi midlayer properly retries
it until it is accepted by the disk), but the sym53c8xx_2 driver aborts
the following requests with DID_SOFT_ERROR --- for them, the midlayer
does just a few retries and then signals the error up to sd.
The result is that disk returning QUEUE FULL causes request failures.
The error was reproduced on 53c895 with COMPAQ BD03685A24 disk
(rebranded ST336607LC) with command queue 48 or 64 tags. The disk has
64 tags, but under some access patterns it return QUEUE FULL when there
are less than 64 pending tags. The SCSI specification allows returning
QUEUE FULL anytime and it is up to the host to retry.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: Matthew Wilcox <matthew@wil.cx>
Cc: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
commit b14bf2d0c0358140041d1c1805a674376964d0e0 upstream.
Some buggy JMicron USB-ATA bridges don't know how to translate the FUA
bit in READs or WRITEs. This patch adds an entry in unusual_devs.h
and a blacklist flag to tell the sd driver not to use FUA.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Michael Büsch <m@bues.ch>
Tested-by: Michael Büsch <m@bues.ch>
Acked-by: James Bottomley <James.Bottomley@HansenPartnership.com>
CC: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[bwh: Backported to 3.2:
- Adjust context
- Use sd_printk() not sd_first_printk()]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
commit 7114aae02742d6b5c5a0d39a41deb61d415d3717 upstream.
Add a memory barrier prior to sending a new command to the VIOS
to ensure the VIOS does not receive stale data in the command buffer.
Also add a memory barrier when processing the CRQ for completed commands.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Acked-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
[bwh: Backported to 3.2: as the iSeries code is still present, these
functions have different names and live in rpa_vscsi.c.]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
commit 9ee755974bea2f9880e517ec985dc9dede1b3a36 upstream.
If a CRQ reset is triggered for some reason while in the middle
of performing VSCSI adapter initialization, we don't want to
call the done function for the initialization MAD commands as
this will only result in two threads attempting initialization
at the same time, resulting in failures.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Acked-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
commit 11f8a7b31f2140b0dc164bb484281235ffbe51d3 upstream.
The assumption that sizeof(long) >= sizeof(resource_size_t) can lead to
truncation of the PCI resource address, meaning this driver didn't work
on 32-bit systems with 64-bit PCI adressing ranges.
Signed-off-by: Ben Collins <ben.c@servergy.com>
Acked-by: Sumit Saxena <sumit.saxena@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
commit d555a2abf3481f81303d835046a5ec2c4fb3ca8e upstream.
We unconditionally execute scsi_eh_get_sense() to make sure all failed
commands that should have sense attached, do. However, the routine forgets
that some commands, because of the way they fail, will not have any sense code
... we should not bother them with a REQUEST_SENSE command. Fix this by
testing to see if we actually got a CHECK_CONDITION return and skip asking for
sense if we don't.
Tested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
commit f2495e228fce9f9cec84367547813cbb0d6db15a upstream.
In the highly unusual case where two threads are running concurrently through
the scanning code scanning the same target, we run into the situation where
one may allocate the target while the other is still using it. In this case,
because the reap checks for STARGET_CREATED and kills the target without
reference counting, the second thread will do the wrong thing on reap.
Fix this by reference counting even creates and doing the STARGET_CREATED
check in the final put.
Tested-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
commit e63ed0d7a98014fdfc2cfeb3f6dada313dcabb59 upstream.
This patch eliminates the reap_ref and replaces it with a proper kref.
On last put of this kref, the target is removed from visibility in
sysfs. The final call to scsi_target_reap() for the device is done from
__scsi_remove_device() and only if the device was made visible. This
ensures that the target disappears as soon as the last device is gone
rather than waiting until final release of the device (which is often
too long).
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
commit b485462aca7df4e32bcf7efb6f84a69e8b640243 upstream.
Avoid that the code for requeueing SCSI requests triggers a
crash by making sure that that code isn't scheduled anymore
after a device has been removed.
Also, source code inspection of __scsi_remove_device() revealed
a race condition in this function: no new SCSI requests must be
accepted for a SCSI device after device removal started.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
commit af61e27c3f77c7623b5335590ae24b6a5c323e22 upstream.
On suspend, _scsih_suspend calls mpt2sas_base_free_resources, which
in turn calls pci_disable_device if the device is enabled prior to
suspending. However, _scsih_suspend also calls pci_disable_device
itself.
Thus, in the event that the device is enabled prior to suspending,
pci_disable_device will be called twice. This patch removes the
duplicate call to pci_disable_device in _scsi_suspend as it is both
unnecessary and results in a kernel oops.
Signed-off-by: Tyler Stachecki <tstache1@binghamton.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
This reverts commit 584ec12265192bf49dfa270d517380f6723a6956, which
was commit ddfadd7736b677de2d4ca2cd5b4b655368c85a7a upstream. It
causes boot failure on 3.2 although no such problem occurs upstream.
Reported-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Acked-by: Dan Williams <dan.j.williams@intel.com>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
commit b77ed25c9f8402e8b3e49e220edb4ef09ecfbb53 upstream.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
[bwh: Backported to 3.2:
- Adjust context
- QLA83XX was not included]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
commit c59053a23d586675c25d789a7494adfdc02fba57 upstream.
In the first place, the loop 'for' in the macro 'for_each_isci_host'
(drivers/scsi/isci/host.h:314) is incorrect, because it accesses
the 3rd element of 2 element array. After the 2nd iteration it executes
the instruction:
ihost = to_pci_info(pdev)->hosts[2]
(while the size of the 'hosts' array equals 2) and reads an
out of range element.
In the second place, this loop is incorrectly optimized by GCC v4.8
(see http://marc.info/?l=linux-kernel&m=138998871911336&w=2).
As a result, on platforms with two SCU controllers,
the loop is executed more times than it can be (for i=0,1 and 2).
It causes kernel panic during entering the S3 state
and the following oops after 'rmmod isci':
BUG: unable to handle kernel NULL pointer dereference at (null)
IP: [<ffffffff8131360b>] __list_add+0x1b/0xc0
Oops: 0000 [#1] SMP
RIP: 0010:[<ffffffff8131360b>] [<ffffffff8131360b>] __list_add+0x1b/0xc0
Call Trace:
[<ffffffff81661b84>] __mutex_lock_slowpath+0x114/0x1b0
[<ffffffff81661c3f>] mutex_lock+0x1f/0x30
[<ffffffffa03e97cb>] sas_disable_events+0x1b/0x50 [libsas]
[<ffffffffa03e9818>] sas_unregister_ha+0x18/0x60 [libsas]
[<ffffffffa040316e>] isci_unregister+0x1e/0x40 [isci]
[<ffffffffa0403efd>] isci_pci_remove+0x5d/0x100 [isci]
[<ffffffff813391cb>] pci_device_remove+0x3b/0xb0
[<ffffffff813fbf7f>] __device_release_driver+0x7f/0xf0
[<ffffffff813fc8f8>] driver_detach+0xa8/0xb0
[<ffffffff813fbb8b>] bus_remove_driver+0x9b/0x120
[<ffffffff813fcf2c>] driver_unregister+0x2c/0x50
[<ffffffff813381f3>] pci_unregister_driver+0x23/0x80
[<ffffffffa04152f8>] isci_exit+0x10/0x1e [isci]
[<ffffffff810d199b>] SyS_delete_module+0x16b/0x2d0
[<ffffffff81012a21>] ? do_notify_resume+0x61/0xa0
[<ffffffff8166ce29>] system_call_fastpath+0x16/0x1b
The loop has been corrected.
This patch fixes kernel panic during entering the S3 state
and the above oops.
Signed-off-by: Lukasz Dorau <lukasz.dorau@intel.com>
Reviewed-by: Maciej Patelczyk <maciej.patelczyk@intel.com>
Tested-by: Lukasz Dorau <lukasz.dorau@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
commit ddfadd7736b677de2d4ca2cd5b4b655368c85a7a upstream.
Remove an erroneous BUG_ON() in the case of a hard reset timeout. The
reset timeout handler puts the port into the "awaiting link-up" state.
The timeout causes the device to be disconnected and we need to be in
the awaiting link-up state to re-connect the port. The BUG_ON() made
the incorrect assumption that resets never timeout and we always
complete the reset in the "resetting" state.
Testing this patch also uncovered that libata continues to attempt to
reset the port long after the driver has torn down the context. Once
the driver has committed to abandoning the link it must indicate to
libata that recovery ends by returning -ENODEV from
->lldd_I_T_nexus_reset().
Acked-by: Lukasz Dorau <lukasz.dorau@intel.com>
Reported-by: David Milburn <dmilburn@redhat.com>
Reported-by: Xun Ni <xun.ni@intel.com>
Tested-by: Xun Ni <xun.ni@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
commit dcaf9aed995c2b2a49fb86bbbcfa2f92c797ab5d upstream.
Bfa driver crash is observed while pushing the firmware on to chinook
quad port card due to uninitialized bfi_image_ct2 access which gets
initialized only for CT2 ASIC based cards after request_firmware().
For quard port chinook (CT2 ASIC based), bfi_image_ct2 is not getting
initialized as there is no check for chinook PCI device ID before
request_firmware and instead bfi_image_cb is initialized as it is the
default case for card type check.
This patch includes changes to read the right firmware for quad port chinook.
Signed-off-by: Vijaya Mohan Guvva <vmohan@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
commit b4789b8e6be3151a955ade74872822f30e8cd914 upstream.
It appears that driver runs into a problem here if fibsize is too small
because we allocate user_srbcmd with fibsize size only but later we
access it until user_srbcmd->sg.count to copy it over to srbcmd.
It is not correct to test (fibsize < sizeof(*user_srbcmd)) because this
structure already includes one sg element and this is not needed for
commands without data. So, we would recommend to add the following
(instead of test for fibsize == 0).
Signed-off-by: Mahesh Rajashekhara <Mahesh.Rajashekhara@pmcs.com>
Reported-by: Nico Golde <nico@ngolde.de>
Reported-by: Fabian Yamaguchi <fabs@goesec.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
commit 88bf6d62db4393fa03a58bada9d746312d5b496f upstream.
A return value of 1 is interpreted as an error. See pci_driver.
in local_pci_probe(). If you're wondering how this ever could
have worked, it's because it used to be the case that only return
values less than zero were interpreted as failure. But even in
the current kernel if the driver registers its various entry
points with the kernel, and then returns a value which is
interpreted as failure, those registrations aren't undone, so
the driver still mostly works. However, the driver's remove
function wouldn't be called on rmmod, and pci power management
functions wouldn't work. In the case of Smart Array, since it
has a battery backed cache (or else no cache) even if the driver
is not shut down properly as long as there is no outstanding
i/o, nothing too bad happens, which is why it took so long to
notice.
Requesting backport to stable because the change to pci-driver.c
which requires driver probe functions to return 0 occurred between
2.6.35 and 2.6.36 (the pci power management breakage) and again
between 3.7 and 3.8 (pci_dev->driver getting set to NULL in
local_pci_probe() preventing driver remove function from being
called on rmmod.)
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
commit 2e311fbabdc23b7eaec77313dc3b9a151a5407b5 upstream.
We inadvertantly discarded the scsi status for aborted commands.
For some commands (e.g. reads from tape drives) these can't be retried,
and if we discarded the scsi status, the scsi mid layer couldn't notice
anything was wrong and the error was not reported.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
commit ae5fbae0ccd982dfca0ce363036ed92f5b13f150 upstream.
Since commit 110dd8f19df5 "[SCSI] libsas: fix scr_read/write users and
update the libata documentation" we have been passing pmp=1 and is_cmd=0
to ata_tf_to_fis(). Praveen reports that eSATA attached drives do not
discover correctly. His investigation found that the BIOS was passing
pmp=0 while Linux was passing pmp=1 and failing to discover the drives.
Update libsas to follow the libata example of pulling the pmp setting
from the ata_link and correct is_cmd to be 1 since all tf's submitted
through ->qc_issue are commands. Presumably libsas lldds do not care
about is_cmd as they have sideband mechanisms to perform link
management.
http://marc.info/?l=linux-scsi&m=138179681726990
[jejb: checkpatch fix]
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Reported-by: Praveen Murali <pmurali@logicube.com>
Tested-by: Praveen Murali <pmurali@logicube.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
commit f856567b930dfcdbc3323261bf77240ccdde01f5 upstream.
In commit d496f94d22d1 ('[SCSI] aacraid: fix security weakness') we
added a check on CAP_SYS_RAWIO to the ioctl. The compat ioctls need the
check as well.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
commit 46a7c17d26967922092f3a8291815ffb20f6cabe upstream.
iscsi_if_send_reply() may return -ESRCH if there were no targets to send
data to. Currently we're ignoring this value and looping in attempt to do it
over and over, which will usually lead in a hung task like this one:
[ 4920.817298] INFO: task trinity:9074 blocked for more than 120 seconds.
[ 4920.818527] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 4920.819982] trinity D 0000000000000000 5504 9074 2756 0x00000004
[ 4920.825374] ffff880003961a98 0000000000000086 ffff8800001aa000 ffff8800001aa000
[ 4920.826791] 00000000001d4340 ffff880003961fd8 ffff880003960000 00000000001d4340
[ 4920.828241] 00000000001d4340 00000000001d4340 ffff880003961fd8 00000000001d4340
[ 4920.833231]
[ 4920.833519] Call Trace:
[ 4920.834010] [<ffffffff826363fa>] schedule+0x3a/0x50
[ 4920.834953] [<ffffffff82634ac9>] __mutex_lock_common+0x209/0x5b0
[ 4920.836226] [<ffffffff81af805d>] ? iscsi_if_rx+0x2d/0x990
[ 4920.837281] [<ffffffff81053943>] ? sched_clock+0x13/0x20
[ 4920.838305] [<ffffffff81af805d>] ? iscsi_if_rx+0x2d/0x990
[ 4920.839336] [<ffffffff82634eb0>] mutex_lock_nested+0x40/0x50
[ 4920.840423] [<ffffffff81af805d>] iscsi_if_rx+0x2d/0x990
[ 4920.841434] [<ffffffff810dffed>] ? sub_preempt_count+0x9d/0xd0
[ 4920.842548] [<ffffffff82637bb0>] ? _raw_read_unlock+0x30/0x60
[ 4920.843666] [<ffffffff821f71de>] netlink_unicast+0x1ae/0x1f0
[ 4920.844751] [<ffffffff821f7997>] netlink_sendmsg+0x227/0x350
[ 4920.845850] [<ffffffff821857bd>] ? sock_update_netprioidx+0xdd/0x1b0
[ 4920.847060] [<ffffffff82185732>] ? sock_update_netprioidx+0x52/0x1b0
[ 4920.848276] [<ffffffff8217f226>] sock_aio_write+0x166/0x180
[ 4920.849348] [<ffffffff810dfe41>] ? get_parent_ip+0x11/0x50
[ 4920.850428] [<ffffffff811d0d9a>] do_sync_write+0xda/0x120
[ 4920.851465] [<ffffffff810dffed>] ? sub_preempt_count+0x9d/0xd0
[ 4920.852579] [<ffffffff810dfe41>] ? get_parent_ip+0x11/0x50
[ 4920.853608] [<ffffffff81791887>] ? security_file_permission+0x27/0xb0
[ 4920.854821] [<ffffffff811d0f4c>] vfs_write+0x16c/0x180
[ 4920.855781] [<ffffffff811d104f>] sys_write+0x4f/0xa0
[ 4920.856798] [<ffffffff82638e79>] system_call_fastpath+0x16/0x1b
[ 4920.877487] 1 lock held by trinity/9074:
[ 4920.878239] #0: (rx_queue_mutex){+.+...}, at: [<ffffffff81af805d>] iscsi_if_rx+0x2d/0x990
[ 4920.880005] Kernel panic - not syncing: hung_task: blocked tasks
Signed-off-by: Sasha Levin <levinsasha928@gmail.com>
Acked-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
[ Upstream commit 21af8107f27878813d0364733c0b08813c2c192a ]
Meelis Roos reports a crash in esp_free_lun_tag() in the presense
of a disk which has died.
The issue is that when we issue an autosense command, we do so by
hijacking the original command that caused the check-condition.
When we do so we clear out the ent->tag[] array when we issue it via
find_and_prep_issuable_command(). This is so that the autosense
command is forced to be issued non-tagged.
That is problematic, because it is the value of ent->tag[] which
determines whether we issued the original scsi command as tagged
vs. non-tagged (see esp_alloc_lun_tag()).
And that, in turn, is what trips up the sanity checks in
esp_free_lun_tag(). That function needs the original ->tag[] values
in order to free up the tag slot properly.
Fix this by remembering the original command's tag values, and
having esp_alloc_lun_tag() and esp_free_lun_tag() use them.
Reported-by: Meelis Roos <mroos@linux.ee>
Tested-by: Meelis Roos <mroos@linux.ee>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
commit 984f1733fcee3fbc78d47e26c5096921c5d9946a upstream.
This patch fixes an out-of-bounds error in sd_read_cache_type(), found
by Google's AddressSanitizer tool. When the loop ends, we know that
"offset" lies beyond the end of the data in the buffer, so no Caching
mode page was found. In theory it may be present, but the buffer size
is limited to 512 bytes.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
commit b497ceb964a80ebada3b9b3cea4261409039e25a upstream.
ARM cannot handle udelay for more than 2 miliseconds, so we
should use mdelay instead for those.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: GOTO Masanori <gotom@debian.or.jp>
Cc: YOKOTA Hiroshi <yokota@netlab.is.tsukuba.ac.jp>
Cc: "James E.J. Bottomley" <JBottomley@parallels.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
commit 6431f5d7c6025f8b007af06ea090de308f7e6881 upstream.
Problem: When Hardware IOMMU is on, megaraid_sas driver initialization fails
in kdump kernel with LSI MegaRAID controller(device id-0x73).
Actually this issue needs fix in firmware, but for firmware running in field,
this driver fix is proposed to resolve the issue. At firmware initialization
time, if firmware does not come to ready state, driver will reset the adapter
and retry for firmware transition to ready state unconditionally(not only
executed for kdump kernel).
Signed-off-by: Sumit Saxena <sumit.saxena@lsi.com>
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
commit 085b513f97d8d799d28491239be4b451bcd8c2c5 upstream.
sd_prep_fn will allocate a larger CDB for the command via mempool_alloc
for devices using DIF type 2 protection. This CDB was being freed
in sd_done, which results in a kernel crash if the command is retried
due to a UNIT ATTENTION. This change moves the code to free the larger
CDB into sd_unprep_fn instead, which is invoked after the request is
complete.
It is no longer necessary to call scsi_print_command separately for
this case as the ->cmnd will no longer be NULL in the normal code path.
Also removed conditional test for DIF type 2 when freeing the larger
CDB because the protection_type could have been changed via sysfs while
the command was executing.
Signed-off-by: Ewan D. Milne <emilne@redhat.com>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
commit c3ccb1d7cf4c4549151876dd37c0944a682fd9e1 upstream.
This fixes a regression where Xyratex controllers and disks were lost by the
driver:
https://bugzilla.kernel.org/show_bug.cgi?id=59601
Reported-by: Jack Hill <jackhill@jackhill.us>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|