aboutsummaryrefslogtreecommitdiffstats
path: root/include/linux
Commit message (Collapse)AuthorAgeFilesLines
...
| * | [SG] Get rid of __sg_mark_end()Jens Axboe2007-11-021-10/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | sg_mark_end() overwrites the page_link information, but all users want __sg_mark_end() behaviour where we just set the end bit. That is the most natural way to use the sg list, since you'll fill it in and then mark the end point. So change sg_mark_end() to only set the termination bit. Add a sg_magic debug check as well, and clear a chain pointer if it is set. Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
| * | SG: Make sg_init_one() use general table init functionsJens Axboe2007-11-021-22/+18
| |/ | | | | | | | | | | Don't open code sg_init_one(), make it reuse sg_init_table(). Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
* | libata: increase 128 KB / cmd limit for ATAPI tape drivesTony Battersby2007-11-031-0/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Commands sent to ATAPI tape drives via the SCSI generic (sg) driver are limited in the amount of data that they can transfer by the max_sectors value. The max_sectors value is currently calculated according to the command set for disk drives, which doesn't apply to tape drives. The default max_sectors value of 256 limits ATAPI tape drive commands to 128 KB. This patch against 2.6.24-rc1 increases the max_sectors value for tape drives to 65535, which permits tape drive commands to transfer just under 32 MB. Tested with a SuperMicro PDSME motherboard, AHCI, and a Sony SDX-570V SATA tape drive. Note that some of the chipset drivers also set their own max_sectors value, which may override the value set in libata-core. I don't have any of these chipsets to test, so I didn't go messing with them. Also, ATAPI devices other than tape drives may benefit from similar changes, but I have only tape drives and disk drives to test. Signed-off-by: Tony Battersby <tonyb@cybernetics.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* | Merge branch 'for-linus' of ↵Linus Torvalds2007-11-021-0/+3
|\ \ | |/ |/| | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: Input: linux-input mailing list moved to vger.kernel.org Input: inport, logibm - use KERN_INFO when reporting missing mouse Input: appletouch - idle reset logic broke older Fountains Input: hp_sdc.c - fix section mismatch Input: appletouch - add Johannes Berg as maintainer Input: Add Euro and Dollar key codes Input: xpad - add more USB IDs
| * Input: Add Euro and Dollar key codesCarlos Corbacho2007-10-271-0/+3
| | | | | | | | | | | | | | | | | | Most newer Acer laptops (from 2005 onwards) now ship with an extra Dollar and Euro key either side of the 'Up' arrow. These cannot be mapped in the traditional way, since they are not combination keys. Signed-off-by: Carlos Corbacho <cathectic@gmail.com> Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* | [NET]: docbook fixes for netif_ functionsStephen Hemminger2007-11-011-0/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | Documentation updates for network interfaces. 1. Add doc for netif_napi_add 2. Remove doc for unused returns from netif_rx 3. Add doc for netif_receive_skb [ Incorporated minor mods from Randy Dunlap -DaveM ] Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org> Signed-off-by: David S. Miller <davem@davemloft.net>
* | Revert "Driver core: remove class_device_*_bin_file"Greg Kroah-Hartman2007-10-311-0/+4
| | | | | | | | | | | | | | | | | | | | | | This reverts commit fcd239d3d5575e5cc63aab5c33cf6dc66904f6d6. I messed up, ia64 still uses these files in the current tree, and now can not build the pci code, which all ia64 boxes seem to require :) This fixes that mistake. Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* | Merge branch 'master' of ↵Linus Torvalds2007-10-312-9/+4
|\ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6 * 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: [AF_KEY]: suppress a warning for 64k pages. [TIPC]: Fix headercheck wrt. tipc_config.h [COMPAT]: Fix build on COMPAT platforms when CONFIG_NET is disabled. [CONNECTOR]: Fix a spurious kfree_skb() call [COMPAT]: Fix new dev_ifname32 returning -EFAULT [NET]: Fix incorrect sg_mark_end() calls. [IPVS]: Remove /proc/net/ip_vs_lblcr [IPV6]: remove duplicate call to proc_net_remove [NETNS]: fix net released by rcu callback [NET]: Fix free_netdev on register_netdev failure. [WAN]: fix drivers/net/wan/lmc/ compilation
| * | [TIPC]: Fix headercheck wrt. tipc_config.hDavid S. Miller2007-10-302-9/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | It wants string functions like memcpy() for inline routines, and these define userland interfaces. The only clean way to deal with this is to simply put linux/string.h into unifdef-y and have it include <string.h> when not-__KERNEL__. Signed-off-by: David S. Miller <davem@davemloft.net>
* | | Driver core: remove class_device_*_bin_fileGreg Kroah-Hartman2007-10-301-4/+0
|/ / | | | | | | | | | | | | | | | | | | | | | | These functions are not used by anyone, so remove them from the tree. The class_device code will be removed soon anyway, so no future users will ever be possible. Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* | Merge branch 'upstream-linus' of ↵Linus Torvalds2007-10-301-3/+3
|\ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/netdev-2.6 * 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/netdev-2.6: ixgb: fix TX hangs under heavy load e1000e: Fix typo ! & ixgbe: minor sparse fixes e1000: sparse warnings fixes ixgb: fix sparse warnings e1000e: fix sparse warnings mv643xx_eth: Fix MV643XX_ETH offsets used by Pegasos 2 Blackfin EMAC driver: Fix Ethernet communication bug (dupliated and lost packets) DM9601: Support for ADMtek ADM8515 NIC
| * | mv643xx_eth: Fix MV643XX_ETH offsets used by Pegasos 2Dale Farnsworth2007-10-301-3/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | In the mv643xx_eth driver, we now use offsets from the ethernet register block within the chip, but the pegasos 2 platform still needs offsets from the full chip's register base address. Signed-off-by: Dale Farnsworth <dale@farnsworth.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* | | Merge branch 'upstream-linus' of ↵Linus Torvalds2007-10-301-0/+1
|\ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev * 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev: libata: implement and use ATA_QCFLAG_QUIET libata: stop being overjealous about non-IO commands libata: flush is an IO command sata_promise: cleanups sata_promise: ASIC PRD table bug workaround, take 2
| * | | libata: implement and use ATA_QCFLAG_QUIETTejun Heo2007-10-301-0/+1
| |/ / | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Implement ATA_QCFLAG_QUIET which indicates that there's no need to report if the command fails with AC_ERR_DEV and set it for passthrough commands. Combined with previous changes, this now makes device errors for all direct commands reported directly to the issuer without going through EH actions and reporting. Note that EH is still invoked after non-IO device errors to determine the nature of the error and resume command execution (some controller requires special care after error to continue). It just performs default maintenance after error, examines what's going on, realizes that it's none of its business and reports the command failure without logging any error messages. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* | | Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6Linus Torvalds2007-10-301-0/+1
|\ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: [TIPC]: Add tipc_config.h to include/linux/Kbuild. [WAN]: lmc_ioctl: don't return with locks held [SUNRPC]: fix rpc debugging [TCP]: Saner thash_entries default with much memory. [SUNRPC] rpc_rdma: we need to cast u64 to unsigned long long for printing [IPv4] SNMP: Refer correct memory location to display ICMP out-going statistics [NET]: Fix error reporting in sys_socketpair(). [NETFILTER]: nf_ct_alloc_hashtable(): use __GFP_NOWARN [NET]: Fix race between poll_napi() and net_rx_action() [TCP] MD5: Remove some more unnecessary casting. [TCP] vegas: Fix a bug in disabling slow start by gamma parameter. [IPVS]: use proper timeout instead of fixed value [IPV6] NDISC: Fix setting base_reachable_time_ms variable.
| * | | [TIPC]: Add tipc_config.h to include/linux/Kbuild.David S. Miller2007-10-301-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Needed, as reported in: http://bugzilla.kernel.org/show_bug.cgi?id=9260 Signed-off-by: David S. Miller <davem@davemloft.net>
* | | | IPMI: fix comparison in demangle_device_idCorey Minyard2007-10-301-1/+1
|/ / / | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Coverity spotted some incorrect code in a recent change to the IPMI driver; this patch make sure the data is really long enough to pull the manufacturer id and product id out of a get device id message. Signed-off-by: Corey Minyard <cminyard@mvista.com> Cc: Adrian Bunk <bunk@kernel.org> Cc: Stian Jordet <liste@jordet.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* | | sched: fix /proc/<PID>/stat stime/utime monotonicity, part 2Balbir Singh2007-10-301-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | Extend Peter's patch to fix accounting issues, by keeping stime monotonic too. Signed-off-by: Balbir Singh <balbir@linux.vnet.ibm.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Tested-by: Frans Pop <elendil@planet.nl>
* | | Merge git://git.kernel.org/pub/scm/linux/kernel/git/mingo/linux-2.6-schedLinus Torvalds2007-10-291-0/+1
|\ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * git://git.kernel.org/pub/scm/linux/kernel/git/mingo/linux-2.6-sched: sched: fix style in kernel/sched.c sched: fix style of swap() macro in kernel/sched_fair.c sched: report CPU usage in CFS cgroup directories sched: move rcu_head to task_group struct sched: fix incorrect assumption that cpu 0 exists sched: keep utime/stime monotonic sched: make kernel/sched.c:account_guest_time() static
| * | | sched: keep utime/stime monotonicPeter Zijlstra2007-10-291-0/+1
| |/ / | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | keep utime/stime monotonic. cpustats use utime/stime as a ratio against sum_exec_runtime, as a consequence it can happen - when the ratio changes faster than time accumulates - that either can be appear to go backwards. Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Signed-off-by: Ingo Molnar <mingo@elte.hu>
* | | Revert "x86_64: allocate sparsemem memmap above 4G"Linus Torvalds2007-10-291-1/+0
|/ / | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This reverts commit 2e1c49db4c640b35df13889b86b9d62215ade4b6. First off, testing in Fedora has shown it to cause boot failures, bisected down by Martin Ebourne, and reported by Dave Jobes. So the commit will likely be reverted in the 2.6.23 stable kernels. Secondly, in the 2.6.24 model, x86-64 has now grown support for SPARSEMEM_VMEMMAP, which disables the relevant code anyway, so while the bug is not visible any more, it's become invisible due to the code just being irrelevant and no longer enabled on the only architecture that this ever affected. Reported-by: Dave Jones <davej@redhat.com> Tested-by: Martin Ebourne <fedora@ebourne.me.uk> Cc: Zou Nan hai <nanhai.zou@intel.com> Cc: Suresh Siddha <suresh.b.siddha@intel.com> Cc: Andrew Morton <akpm@linux-foundation.org> Acked-by: Andy Whitcroft <apw@shadowen.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* | Merge branch 'alpm' of ↵Linus Torvalds2007-10-292-1/+41
|\ \ | | | | | | | | | | | | | | | | | | | | | master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev * 'alpm' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev: [libata] AHCI: add hw link power management support [libata] Link power management infrastructure
| * | [libata] Link power management infrastructureKristen Carlson Accardi2007-10-292-1/+41
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Device Initiated Power Management, which is defined in SATA 2.5 can be enabled for disks which support it. This patch enables DIPM when the user sets the link power management policy to "min_power". Additionally, libata drivers can define a function (enable_pm) that will perform hardware specific actions to enable whatever power management policy the user set up for Host Initiated Power management (HIPM). This power management policy will be activated after all disks have been enumerated and intialized. Drivers should also define disable_pm, which will turn off link power management, but not change link power management policy. Documentation/scsi/link_power_management_policy.txt has additional information. Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* | | Merge branch 'upstream-linus' of ↵Linus Torvalds2007-10-292-0/+10
|\ \ \ | |/ / | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev * 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev: [libata] AHCI: fix newly introduced host-reset bug [libata] sata_nv: fix SWNCQ enabling libata: add MAXTOR 7V300F0/VA111900 to NCQ blacklist libata: no need to speed down if already at PIO0 libata: relocate forcing PIO0 on reset pata_ns87415: define SUPERIO_IDE_MAX_RETRIES [libata] Address some checkpatch-spotted issues [libata] fix 'if(' and similar areas that lack whitespace libata: implement ata_wait_after_reset() libata: track SLEEP state and issue SRST to wake it up libata: relocate and fix post-command processing
| * | libata: implement ata_wait_after_reset()Tejun Heo2007-10-291-0/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | On certain device/controller combination, 0xff status is asserted after reset and doesn't get cleared during 150ms post-reset wait. As 0xff status is interpreted as no device (for good reasons), this can lead to misdetection on such cases. This patch implements ata_wait_after_reset() which replaces the 150ms sleep and waits upto ATA_TMOUT_FF_WAIT if status is 0xff. ATA_TMOUT_FF_WAIT is currently 800ms which is enough for HHD424020F7SV00 to get detected but not enough for Quantum GoVault drive which is known to take upto 2s. Without parallel probing, spending 2s on 0xff port would incur too much delay on ata_piix's which use 0xff to indicate empty port and doesn't have SCR register, so GoVault needs to wait till parallel probing. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
| * | libata: track SLEEP state and issue SRST to wake it upTejun Heo2007-10-292-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ATA devices in SLEEP mode don't respond to any commands. SRST is necessary to wake it up. Till now, when a command is issued to a device in SLEEP mode, the command times out, which makes EH reset the device and retry the command after that, causing a long delay. This patch makes libata track SLEEP state and issue SRST automatically if a command is about to be issued to a device in SLEEP. Signed-off-by: Tejun Heo <htejun@gmail.com> Cc: Bruce Allen <ballen@gravity.phys.uwm.edu> Cc: Andrew Paprocki <andrew@ishiboo.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* | | Merge branch 'for-linus' of git://git.kernel.dk/linux-2.6-blockLinus Torvalds2007-10-291-1/+1
|\ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * 'for-linus' of git://git.kernel.dk/linux-2.6-block: compat_ioctl: fix block device compat ioctl regression [BLOCK] Fix bad sharing of tag busy list on queues with shared tag maps Fix a build error when BLOCK=n block: use lock bitops for the tag map. cciss: update copyright notices cfq_get_queue: fix possible NULL pointer access blk_sync_queue() should cancel request_queue->unplug_work cfq_exit_queue() should cancel cfq_data->unplug_work block layer: remove a unused argument of drive_stat_acct()
| * | | [BLOCK] Fix bad sharing of tag busy list on queues with shared tag mapsJens Axboe2007-10-291-1/+1
| |/ / | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | For the locking to work, only the tag map and tag bit map may be shared (incidentally, I was just explaining this to Nick yesterday, but I apparently didn't review the code well enough myself). But we also share the busy list! The busy_list must be queue private, or we need a block_queue_tag covering lock as well. So we have to move the busy_list to the queue. This'll work fine, and it'll actually also fix a problem with blk_queue_invalidate_tags() which will invalidate tags across all shared queues. This is a bit confusing, the low level driver should call it for each queue seperately since otherwise you cannot kill tags on just a single queue for eg a hard drive that stops responding. Since the function has no callers currently, it's not an issue. Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
* | | Merge branch 'sg' of git://git.kernel.dk/linux-2.6-blockLinus Torvalds2007-10-291-3/+7
|\ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * 'sg' of git://git.kernel.dk/linux-2.6-block: Correction of "Update drivers to use sg helpers" patch for IMXMMC driver sg_init_table() should use unsigned loop index variable sg_last() should use unsigned loop index variable Initialise scatter/gather list in sg driver Initialise scatter/gather list in ata_sg_setup x86: fix pci-gart failure handling SG: s390-scsi: missing size parameter in zfcp_address_to_sg() SG: clear termination bit in sg_chain()
| * | | sg_init_table() should use unsigned loop index variableChuck Lever2007-10-291-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Clean up: fix a mixed sign comparison in sg_init_table() accidentally introduced by commit d6ec0842. The sign of the loop index variable should match the sign of the "nents" argument. Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Cc: Jens Axboe <jens.axboe@oracle.com> Signed-off-by: Jens Axboe <axboe@carl.home.kernel.dk>
| * | | sg_last() should use unsigned loop index variableChuck Lever2007-10-291-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Clean up: fix a mixed sign comparison in sg_last() accidentally introduced by commit 70eb8040. The sign of the loop index variable should match the sign of the "nents" argument. Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: Jens Axboe <axboe@carl.home.kernel.dk>
| * | | SG: clear termination bit in sg_chain()Jens Axboe2007-10-291-1/+5
| |/ / | | | | | | | | | | | | | | | | | | Since we are using the last entry in the list, clear any possible termination bit that may have already been set. Pointed out by Rusty. Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
* | | fix abuses of ptrdiff_tAl Viro2007-10-291-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Use of ptrdiff_t in places like - if (!access_ok(VERIFY_WRITE, u_tmp->rx_buf, u_tmp->len)) + if (!access_ok(VERIFY_WRITE, (u8 __user *) + (ptrdiff_t) u_tmp->rx_buf, + u_tmp->len)) is wrong; for one thing, it's a bad C (it's what uintptr_t is for; in general we are not even promised that ptrdiff_t is large enough to hold a pointer, just enough to hold a difference between two pointers within the same object). For another, it confuses the fsck out of sparse. Use unsigned long or uintptr_t instead. There are several places misusing ptrdiff_t; fixed. Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* | | SUNRPC endianness annotationsAl Viro2007-10-291-16/+16
| | | | | | | | | | | | | | | | | | | | | | | | rpcrdma stuff lacks endianness annotations for on-the-wire data. Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Acked-by: David S. Miller <davem@davemloft.net> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* | | x86 merge fallout: umlAl Viro2007-10-291-6/+1
|/ / | | | | | | | | | | | | | | Don't undef __i386__/__x86_64__ in uml anymore, make sure that (few) places that required adjusting the ifdefs got those. Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* | fix breakage in pegasos_ethAl Viro2007-10-271-0/+3
|/ | | | | | | | Fix fallout from commit b45d9147f1582333e180e1023624c003874b7312 ("mv643xx_eth: Remove unused register defines") Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* Merge branch 'master' of ↵Linus Torvalds2007-10-262-7/+7
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6 * 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (32 commits) [NetLabel]: correct usage of RCU locking [TCP]: fix D-SACK cwnd handling [NET] napi: use non-interruptible sleep in napi_disable [SCTP] net/sctp/auth.c: make 3 functions static [TCP]: Add missing I/O AT code to ipv6 side. [SCTP]: #if 0 sctp_update_copy_cksum() [INET]: Unexport icmpmsg_statistics [NET]: Unexport sock_enable_timestamp(). [TCP]: Make tcp_match_skb_to_sack() static. [IRDA]: Make ircomm_tty static. [NET] fs/proc/proc_net.c: make a struct static [NET] dev_change_name: ignore changes to same name [NET]: Document some simple rules for actions [NET_CLS_ACT]: Use skb_act_clone [NET_CLS_ACT]: Introduce skb_act_clone [TCP]: Fix scatterlist handling in MD5 signature support. [IPSEC]: Fix scatterlist handling in skb_icv_walk(). [IPSEC]: Add missing sg_init_table() calls to ESP. [CRYPTO]: Initialize TCRYPT on-stack scatterlist objects correctly. [CRYPTO]: HMAC needs some more scatterlist fixups. ...
| * [NET] napi: use non-interruptible sleep in napi_disableBenjamin Herrenschmidt2007-10-261-1/+1
| | | | | | | | | | | | | | | | | | | | The current napi_disable() uses msleep_interruptible() but doesn't (and can't) exit in case there's a signal, thus ending up doing a hot spin without a cpu_relax. Use uninterruptible sleep instead. Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Acked-by: Jeff Garzik <jeff@garzik.org> Signed-off-by: David S. Miller <davem@davemloft.net>
| * Merge master.kernel.org:/pub/scm/linux/kernel/git/acme/net-2.6David S. Miller2007-10-261-6/+6
| |\
| | * [DCCP]: Convert Reset code into socket error numberGerrit Renker2007-10-241-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This adds support for converting the 11 currently defined Reset codes into system error numbers, which are stored in sk_err for further interpretation. This makes the externally visible API behaviour similar to TCP, since a client connecting to a non-existing port will experience ECONNREFUSED. * Code 0, Unspecified, is interpreted as non-error (0); * Code 1, Closed (normal termination), also maps into 0; * Code 2, Aborted, maps into "Connection reset by peer" (ECONNRESET); * Code 3, No Connection and Code 7, Connection Refused, map into "Connection refused" (ECONNREFUSED); * Code 4, Packet Error, maps into "No message of desired type" (ENOMSG); * Code 5, Option Error, maps into "Illegal byte sequence" (EILSEQ); * Code 6, Mandatory Error, maps into "Operation not supported on transport endpoint" (EOPNOTSUPP); * Code 8, Bad Service Code, maps into "Invalid request code" (EBADRQC); * Code 9, Too Busy, maps into "Too many users" (EUSERS); * Code 10, Bad Init Cookie, maps into "Invalid request descriptor" (EBADR); * Code 11, Aggression Penalty, maps into "Quota exceeded" (EDQUOT) which makes sense in terms of using more than the `fair share' of bandwidth. Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk> Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz> Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
| | * [DCCP]: Retrieve packet sequence number for error reportingGerrit Renker2007-10-241-6/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This fixes a problem when analysing erroneous packets in dccp_v{4,6}_err: * dccp_hdr_seq currently takes an skb * however, the transport headers in the skb are shifted, due to the preceding IPv4/v6 header. Fixed for v4 and v6 by changing dccp_hdr_seq to take a struct dccp_hdr as argument. Verified that the correct sequence number is now reported in the error handler. Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk> Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz> Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
* | | De-constify sched.hAlexey Dobriyan2007-10-261-14/+14
|/ / | | | | | | | | | | | | | | | | | | | | | | | | | | | | [PATCH] De-constify sched.h This reverts commit a8972ccf00b7184a743eb6cd9bc7f3443357910c ("sched: constify sched.h") 1) Patch doesn't change any code here, so gcc is already smart enough to "feel" constness in such simple functions. 2) There is no such thing as const task_struct. Anyone who think otherwise deserves compiler warning. Signed-off-by: Alexey Dobriyan <adobriyan@sw.ru> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* | Merge branch 'master' of ↵Linus Torvalds2007-10-252-2/+4
|\ \ | |/ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6 * 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: [IPV4]: Explicitly call fib_get_table() in fib_frontend.c [NET]: Use BUILD_BUG_ON in net/core/flowi.c [NET]: Remove in-code externs for some functions from net/core/dev.c [NET]: Don't declare extern variables in net/core/sysctl_net_core.c [TCP]: Remove unneeded implicit type cast when calling tcp_minshall_update() [NET]: Treat the sign of the result of skb_headroom() consistently [9P]: Fix missing unlock before return in p9_mux_poll_start [PKT_SCHED]: Fix sch_prio.c build with CONFIG_NETDEVICES_MULTIQUEUE [IPV4] ip_gre: sendto/recvfrom NBMA address [SCTP]: Consolidate sctp_ulpq_renege_xxx functions [NETLINK]: Fix ACK processing after netlink_dump_start [VLAN]: MAINTAINERS update [DCCP]: Implement SIOCINQ/FIONREAD [NET]: Validate device addr prior to interface-up
| * [NET]: Treat the sign of the result of skb_headroom() consistentlyChuck Lever2007-10-231-2/+2
| | | | | | | | | | | | | | | | | | In some places, the result of skb_headroom() is compared to an unsigned integer, and in others, the result is compared to a signed integer. Make the comparisons consistent and correct. Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * [NET]: Validate device addr prior to interface-upJeff Garzik2007-10-231-0/+2
| | | | | | | | | | Signed-off-by: Jeff Garzik <jgarzik@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | Merge branch 'sg' of git://git.kernel.dk/linux-2.6-blockLinus Torvalds2007-10-251-12/+31
|\ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * 'sg' of git://git.kernel.dk/linux-2.6-block: fix sg_phys to use dma_addr_t ub: add sg_init_table for sense and read capacity commands x86: pci-gart fix blackfin: fix sg fallout xtensa: dma-mapping.h is using linux/scatterlist.h functions, so include it SG: audit of drivers that use blk_rq_map_sg() arch/um/drivers/ubd_kern.c: fix a building error SG: Change sg_set_page() to take length and offset argument AVR32: Fix sg_page breakage mmc: sg fallout m68k: sg fallout More SG build fixes sg: add missing sg_init_table calls to zfcp SG build fix
| * | fix sg_phys to use dma_addr_tHugh Dickins2007-10-251-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | x86_32 CONFIG_HIGHMEM64G with 5GB RAM hung when booting, after issuing some "request_module: runaway loop modprobe binfmt-0000" messages in trying to exec /sbin/init. The binprm buf doesn't see the right ".ELF" header because sg_phys() is providing the wrong physical addresses for high pages: a 32-bit unsigned long is too small in this case, we need to use dma_addr_t. Signed-off-by: Hugh Dickins <hugh@veritas.com> Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
| * | SG: Change sg_set_page() to take length and offset argumentJens Axboe2007-10-241-11/+29
| |/ | | | | | | | | | | | | | | | | | | Most drivers need to set length and offset as well, so may as well fold those three lines into one. Add sg_assign_page() for those two locations that only needed to set the page, where the offset/length is set outside of the function context. Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
* | Merge git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-lguestLinus Torvalds2007-10-252-17/+11
|\ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-lguest: lguest: documentation update lguest: Add to maintainers file. lguest: build fix lguest: clean up lguest_launcher.h lguest: remove unused "wake" element from struct lguest lguest: use defines from x86 headers instead of magic numbers lguest: example launcher header cleanup.
| * | lguest: documentation updateRusty Russell2007-10-252-3/+7
| | | | | | | | | | | | | | | | | | | | | | | | Went through the documentation doing typo and content fixes. This patch contains only comment and whitespace changes. Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>