aboutsummaryrefslogtreecommitdiffstats
path: root/net/ipv6
Commit message (Collapse)AuthorAgeFilesLines
* ipv6: Fix build failure when CONFIG_INET disabledBen Hutchings2015-10-131-1/+2
| | | | | | | | | | output_core.c, added in 3.2.66, is only needed and can only be compiled when CONFIG_INET is enabled. The condition in the Makefile is already correct upstream. Reported-by: kbuild test robot <fengguang.wu@intel.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
* udp: fix behavior of wrong checksumsEric Dumazet2015-08-071-4/+2
| | | | | | | | | | | | | | | | | | | | | | | | commit beb39db59d14990e401e235faf66a6b9b31240b0 upstream. We have two problems in UDP stack related to bogus checksums : 1) We return -EAGAIN to application even if receive queue is not empty. This breaks applications using edge trigger epoll() 2) Under UDP flood, we can loop forever without yielding to other processes, potentially hanging the host, especially on non SMP. This patch is an attempt to make things better. We might in the future add extra support for rt applications wanting to better control time spent doing a recv() in a hostile environment. For example we could validate checksums before queuing packets in socket receive queue. Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
* udp: only allow UFO for packets from SOCK_DGRAM socketsMichal Kubeček2015-05-091-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | [ Upstream commit acf8dd0a9d0b9e4cdb597c2f74802f79c699e802 ] If an over-MTU UDP datagram is sent through a SOCK_RAW socket to a UFO-capable device, ip_ufo_append_data() sets skb->ip_summed to CHECKSUM_PARTIAL unconditionally as all GSO code assumes transport layer checksum is to be computed on segmentation. However, in this case, skb->csum_start and skb->csum_offset are never set as raw socket transmit path bypasses udp_send_skb() where they are usually set. As a result, driver may access invalid memory when trying to calculate the checksum and store the result (as observed in virtio_net driver). Moreover, the very idea of modifying the userspace provided UDP header is IMHO against raw socket semantics (I wasn't able to find a document clearly stating this or the opposite, though). And while allowing CHECKSUM_NONE in the UFO case would be more efficient, it would be a bit too intrusive change just to handle a corner case like this. Therefore disallowing UFO for packets from SOCK_DGRAM seems to be the best option. Signed-off-by: Michal Kubecek <mkubecek@suse.cz> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
* ipv6: stop sending PTB packets for MTU < 1280Hagen Paul Pfeifer2015-05-091-5/+2
| | | | | | | | | | | | | | | | | | | [ Upstream commit 9d289715eb5c252ae15bd547cb252ca547a3c4f2 ] Reduce the attack vector and stop generating IPv6 Fragment Header for paths with an MTU smaller than the minimum required IPv6 MTU size (1280 byte) - called atomic fragments. See IETF I-D "Deprecating the Generation of IPv6 Atomic Fragments" [1] for more information and how this "feature" can be misused. [1] https://tools.ietf.org/html/draft-ietf-6man-deprecate-atomfrag-generation-00 Signed-off-by: Fernando Gont <fgont@si6networks.com> Signed-off-by: Hagen Paul Pfeifer <hagen@jauu.net> Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
* ip: zero sockaddr returned on error queueWillem de Bruijn2015-05-091-7/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | [ Upstream commit f812116b174e59a350acc8e4856213a166a91222 ] The sockaddr is returned in IP(V6)_RECVERR as part of errhdr. That structure is defined and allocated on the stack as struct { struct sock_extended_err ee; struct sockaddr_in(6) offender; } errhdr; The second part is only initialized for certain SO_EE_ORIGIN values. Always initialize it completely. An MTU exceeded error on a SOCK_RAW/IPPROTO_RAW is one example that would return uninitialized bytes. Signed-off-by: Willem de Bruijn <willemb@google.com> ---- Also verified that there is no padding between errhdr.ee and errhdr.offender that could leak additional kernel data. Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> [bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
* ipv6: Don't reduce hop limit for an interfaceD.S. Ljungmark2015-05-091-1/+8
| | | | | | | | | | | | | | | | | | | | | | | commit 6fd99094de2b83d1d4c8457f2c83483b2828e75a upstream. A local route may have a lower hop_limit set than global routes do. RFC 3756, Section 4.2.7, "Parameter Spoofing" > 1. The attacker includes a Current Hop Limit of one or another small > number which the attacker knows will cause legitimate packets to > be dropped before they reach their destination. > As an example, one possible approach to mitigate this threat is to > ignore very small hop limits. The nodes could implement a > configurable minimum hop limit, and ignore attempts to set it below > said limit. Signed-off-by: D.S. Ljungmark <ljungmark@modio.se> Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net> [bwh: Backported to 3.2: adjust ND_PRINTK() usage] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
* ipv6: fix ipv6_cow_metrics for non DST_HOST caseMartin KaFai Lau2015-05-091-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | commit 3b4711757d7903ab6fa88a9e7ab8901b8227da60 upstream. ipv6_cow_metrics() currently assumes only DST_HOST routes require dynamic metrics allocation from inetpeer. The assumption breaks when ndisc discovered router with RTAX_MTU and RTAX_HOPLIMIT metric. Refer to ndisc_router_discovery() in ndisc.c and note that dst_metric_set() is called after the route is created. This patch creates the metrics array (by calling dst_cow_metrics_generic) in ipv6_cow_metrics(). Test: radvd.conf: interface qemubr0 { AdvLinkMTU 1300; AdvCurHopLimit 30; prefix fd00:face:face:face::/64 { AdvOnLink on; AdvAutonomous on; AdvRouterAddr off; }; }; Before: [root@qemu1 ~]# ip -6 r show | egrep -v unreachable fd00:face:face:face::/64 dev eth0 proto kernel metric 256 expires 27sec fe80::/64 dev eth0 proto kernel metric 256 default via fe80::74df:d0ff:fe23:8ef2 dev eth0 proto ra metric 1024 expires 27sec After: [root@qemu1 ~]# ip -6 r show | egrep -v unreachable fd00:face:face:face::/64 dev eth0 proto kernel metric 256 expires 27sec mtu 1300 fe80::/64 dev eth0 proto kernel metric 256 mtu 1300 default via fe80::74df:d0ff:fe23:8ef2 dev eth0 proto ra metric 1024 expires 27sec mtu 1300 hoplimit 30 Fixes: 8e2ec639173f325 (ipv6: don't use inetpeer to store metrics for routes.) Signed-off-by: Martin KaFai Lau <kafai@fb.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
* ipv6: fib: fix fib dump restartKumar Sundararajan2015-03-061-1/+2
| | | | | | | | | | | | | | | | | | commit 1c2658545816088477e91860c3a645053719cb54 upstream. When the ipv6 fib changes during a table dump, the walk is restarted and the number of nodes dumped are skipped. But the existing code doesn't advance to the next node after a node is skipped. This can cause the dump to loop or produce lots of duplicates when the fib is modified during the dump. This change advances the walk to the next node if the current node is skipped after a restart. Signed-off-by: Kumar Sundararajan <kumar@fb.com> Signed-off-by: Chris Mason <clm@fb.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
* ipv6: fib: fix fib dump restartEric Dumazet2015-03-061-2/+2
| | | | | | | | | | | | | | | | | | | | commit fa809e2fd6e317226c046202a88520962672eac0 upstream. Commit 2bec5a369ee79576a3 (ipv6: fib: fix crash when changing large fib while dumping it) introduced ability to restart the dump at tree root, but failed to skip correctly a count of already dumped entries. Code didn't match Patrick intent. We must skip exactly the number of already dumped entries. Note that like other /proc/net files or netlink producers, we could still dump some duplicates entries. Reported-by: Debabrata Banerjee <dbavatar@gmail.com> Reported-by: Josh Hunt <johunt@akamai.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
* ipv6: mld: fix add_grhead skb_over_panic for devs with large MTUsDaniel Borkmann2015-02-201-4/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | commit 4c672e4b42bc8046d63a6eb0a2c6a450a501af32 upstream. It has been reported that generating an MLD listener report on devices with large MTUs (e.g. 9000) and a high number of IPv6 addresses can trigger a skb_over_panic(): skbuff: skb_over_panic: text:ffffffff80612a5d len:3776 put:20 head:ffff88046d751000 data:ffff88046d751010 tail:0xed0 end:0xec0 dev:port1 ------------[ cut here ]------------ kernel BUG at net/core/skbuff.c:100! invalid opcode: 0000 [#1] SMP Modules linked in: ixgbe(O) CPU: 3 PID: 0 Comm: swapper/3 Tainted: G O 3.14.23+ #4 [...] Call Trace: <IRQ> [<ffffffff80578226>] ? skb_put+0x3a/0x3b [<ffffffff80612a5d>] ? add_grhead+0x45/0x8e [<ffffffff80612e3a>] ? add_grec+0x394/0x3d4 [<ffffffff80613222>] ? mld_ifc_timer_expire+0x195/0x20d [<ffffffff8061308d>] ? mld_dad_timer_expire+0x45/0x45 [<ffffffff80255b5d>] ? call_timer_fn.isra.29+0x12/0x68 [<ffffffff80255d16>] ? run_timer_softirq+0x163/0x182 [<ffffffff80250e6f>] ? __do_softirq+0xe0/0x21d [<ffffffff8025112b>] ? irq_exit+0x4e/0xd3 [<ffffffff802214bb>] ? smp_apic_timer_interrupt+0x3b/0x46 [<ffffffff8063f10a>] ? apic_timer_interrupt+0x6a/0x70 mld_newpack() skb allocations are usually requested with dev->mtu in size, since commit 72e09ad107e7 ("ipv6: avoid high order allocations") we have changed the limit in order to be less likely to fail. However, in MLD/IGMP code, we have some rather ugly AVAILABLE(skb) macros, which determine if we may end up doing an skb_put() for adding another record. To avoid possible fragmentation, we check the skb's tailroom as skb->dev->mtu - skb->len, which is a wrong assumption as the actual max allocation size can be much smaller. The IGMP case doesn't have this issue as commit 57e1ab6eaddc ("igmp: refine skb allocations") stores the allocation size in the cb[]. Set a reserved_tailroom to make it fit into the MTU and use skb_availroom() helper instead. This also allows to get rid of igmp_skb_size(). Reported-by: Wei Liu <lw1a2.jing@gmail.com> Fixes: 72e09ad107e7 ("ipv6: avoid high order allocations") Signed-off-by: Daniel Borkmann <dborkman@redhat.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Hannes Frederic Sowa <hannes@stressinduktion.org> Cc: David L Stevens <david.stevens@oracle.com> Acked-by: Eric Dumazet <edumazet@google.com> Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net> [bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
* ipv6: Remove all uses of LL_ALLOCATED_SPACEHerbert Xu2015-02-204-12/+27
| | | | | | | | | | | | | | | | | | | | | | | commit a7ae1992248e5cf9dc5bd35695ab846d27efe15f upstream. ipv6: Remove all uses of LL_ALLOCATED_SPACE The macro LL_ALLOCATED_SPACE was ill-conceived. It applies the alignment to the sum of needed_headroom and needed_tailroom. As the amount that is then reserved for head room is needed_headroom with alignment, this means that the tail room left may be too small. This patch replaces all uses of LL_ALLOCATED_SPACE in net/ipv6 with the macro LL_RESERVED_SPACE and direct reference to needed_tailroom. This also fixes the problem with needed_headroom changing between allocating the skb and reserving the head room. Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net> [bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
* tcp: md5: remove spinlock usage in fast pathEric Dumazet2015-01-011-6/+1
| | | | | | | | | | | | | | | | | | | | | | | | commit 71cea17ed39fdf1c0634f530ddc6a2c2fc601c2b upstream. TCP md5 code uses per cpu variables but protects access to them with a shared spinlock, which is a contention point. [ tcp_md5sig_pool_lock is locked twice per incoming packet ] Makes things much simpler, by allocating crypto structures once, first time a socket needs md5 keys, and not deallocating them as they are really small. Next step would be to allow crypto allocations being done in a NUMA aware way. Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net> [bwh: Backported to 3.2: - Adjust context - Conditions for alloc/free are quite different] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
* drivers/net, ipv6: Select IPv6 fragment idents for virtio UFO packetsBen Hutchings2015-01-012-1/+39
| | | | | | | | | | | | | | commit 5188cd44c55db3e92cd9e77a40b5baa7ed4340f7 upstream. UFO is now disabled on all drivers that work with virtio net headers, but userland may try to send UFO/IPv6 packets anyway. Instead of sending with ID=0, we should select identifiers on their behalf (as we used to). Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Fixes: 916e4cf46d02 ("ipv6: reuse ip6_frag_id from ip6_ufo_append_data") Signed-off-by: David S. Miller <davem@davemloft.net> [bwh: For 3.2, net/ipv6/output_core.c is a completely new file]
* tcp: be more strict before accepting ECN negociationEric Dumazet2014-12-141-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | commit bd14b1b2e29bd6812597f896dde06eaf7c6d2f24 upstream. It appears some networks play bad games with the two bits reserved for ECN. This can trigger false congestion notifications and very slow transferts. Since RFC 3168 (6.1.1) forbids SYN packets to carry CT bits, we can disable TCP ECN negociation if it happens we receive mangled CT bits in the SYN packet. Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Perry Lorier <perryl@google.com> Cc: Matt Mathis <mattmathis@google.com> Cc: Yuchung Cheng <ycheng@google.com> Cc: Neal Cardwell <ncardwell@google.com> Cc: Wilmer van der Gaast <wilmer@google.com> Cc: Ankur Jain <jankur@google.com> Cc: Tom Herbert <therbert@google.com> Cc: Dave Täht <dave.taht@bufferbloat.net> Acked-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Cc: Florian Westphal <fw@strlen.de>
* ipv6: reuse ip6_frag_id from ip6_ufo_append_dataHannes Frederic Sowa2014-11-051-1/+1
| | | | | | | | | | | | | | | | | | | | commit 916e4cf46d0204806c062c8c6c4d1f633852c5b6 upstream. Currently we generate a new fragmentation id on UFO segmentation. It is pretty hairy to identify the correct net namespace and dst there. Especially tunnels use IFF_XMIT_DST_RELEASE and thus have no skb_dst available at all. This causes unreliable or very predictable ipv6 fragmentation id generation while segmentation. Luckily we already have pregenerated the ip6_frag_id in ip6_ufo_append_data and can use it here. Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net> [bwh: Backported to 3.2: adjust filename, indentation] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
* ipv6: reallocate addrconf router for ipv6 address when lo device upchenweilong2014-11-051-2/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | It fix the bug 67951 on bugzilla https://bugzilla.kernel.org/show_bug.cgi?id=67951 The patch can't be applied directly, as it' used the function introduced by "commit 94e187c0" ip6_rt_put(), that patch can't be applied directly either. ==================== From: Gao feng <gaofeng@cn.fujitsu.com> commit 33d99113b1102c2d2f8603b9ba72d89d915c13f5 upstream. This commit don't have a stable tag, but it fix the bug no reply after loopback down-up.It's very worthy to be applied to stable 3.4 kernels. The bug is 67951 on bugzilla https://bugzilla.kernel.org/show_bug.cgi?id=67951 CC: Sabrina Dubroca <sd@queasysnail.net> CC: Hannes Frederic Sowa <hannes@stressinduktion.org> Reported-by: Weilong Chen <chenweilong@huawei.com> Signed-off-by: Weilong Chen <chenweilong@huawei.com> Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com> Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net> [weilong: s/ip6_rt_put/dst_release] Signed-off-by: Chen Weilong <chenweilong@huawei.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
* ip: make IP identifiers less predictableEric Dumazet2014-09-131-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | [ Upstream commit 04ca6973f7c1a0d8537f2d9906a0cf8e69886d75 ] In "Counting Packets Sent Between Arbitrary Internet Hosts", Jeffrey and Jedidiah describe ways exploiting linux IP identifier generation to infer whether two machines are exchanging packets. With commit 73f156a6e8c1 ("inetpeer: get rid of ip_id_count"), we changed IP id generation, but this does not really prevent this side-channel technique. This patch adds a random amount of perturbation so that IP identifiers for a given destination [1] are no longer monotonically increasing after an idle period. Note that prandom_u32_max(1) returns 0, so if generator is used at most once per jiffy, this patch inserts no hole in the ID suite and do not increase collision probability. This is jiffies based, so in the worst case (HZ=1000), the id can rollover after ~65 seconds of idle time, which should be fine. We also change the hash used in __ip_select_ident() to not only hash on daddr, but also saddr and protocol, so that ICMP probes can not be used to infer information for other protocols. For IPv6, adds saddr into the hash as well, but not nexthdr. If I ping the patched target, we can see ID are now hard to predict. 21:57:11.008086 IP (...) A > target: ICMP echo request, seq 1, length 64 21:57:11.010752 IP (... id 2081 ...) target > A: ICMP echo reply, seq 1, length 64 21:57:12.013133 IP (...) A > target: ICMP echo request, seq 2, length 64 21:57:12.015737 IP (... id 3039 ...) target > A: ICMP echo reply, seq 2, length 64 21:57:13.016580 IP (...) A > target: ICMP echo request, seq 3, length 64 21:57:13.019251 IP (... id 3437 ...) target > A: ICMP echo reply, seq 3, length 64 [1] TCP sessions uses a per flow ID generator not changed by this patch. Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: Jeffrey Knockel <jeffk@cs.unm.edu> Reported-by: Jedidiah R. Crandall <crandall@cs.unm.edu> Cc: Willy Tarreau <w@1wt.eu> Cc: Hannes Frederic Sowa <hannes@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
* inetpeer: get rid of ip_id_countEric Dumazet2014-09-131-14/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | [ Upstream commit 73f156a6e8c1074ac6327e0abd1169e95eb66463 ] Ideally, we would need to generate IP ID using a per destination IP generator. linux kernels used inet_peer cache for this purpose, but this had a huge cost on servers disabling MTU discovery. 1) each inet_peer struct consumes 192 bytes 2) inetpeer cache uses a binary tree of inet_peer structs, with a nominal size of ~66000 elements under load. 3) lookups in this tree are hitting a lot of cache lines, as tree depth is about 20. 4) If server deals with many tcp flows, we have a high probability of not finding the inet_peer, allocating a fresh one, inserting it in the tree with same initial ip_id_count, (cf secure_ip_id()) 5) We garbage collect inet_peer aggressively. IP ID generation do not have to be 'perfect' Goal is trying to avoid duplicates in a short period of time, so that reassembly units have a chance to complete reassembly of fragments belonging to one message before receiving other fragments with a recycled ID. We simply use an array of generators, and a Jenkin hash using the dst IP as a key. ipv6_select_ident() is put back into net/ipv6/ip6_output.c where it belongs (it is only used from this file) secure_ip_id() and secure_ipv6_id() no longer are needed. Rename ip_select_ident_more() to ip_select_ident_segs() to avoid unnecessary decrement/increment of the number of segments. Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
* Revert "net: ip, ipv6: handle gso skbs in forwarding path"Ben Hutchings2014-08-061-12/+1
| | | | | | | | | | This reverts commit caa5344994778a2b4725b2d75c74430f76925e4a, which was commit fe6cc55f3a9a053482a76f5a6b2257cee51b4663 upstream. In 3.2, the transport header length is not calculated in the forwarding path, so skb_gso_network_seglen() returns an incorrect result. We also have problems due to the local_df flag not being set correctly. Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
* net: fix inet_getid() and ipv6_select_ident() bugsEric Dumazet2014-07-111-8/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | [ Upstream commit 39c36094d78c39e038c1e499b2364e13bce36f54 ] I noticed we were sending wrong IPv4 ID in TCP flows when MTU discovery is disabled. Note how GSO/TSO packets do not have monotonically incrementing ID. 06:37:41.575531 IP (id 14227, proto: TCP (6), length: 4396) 06:37:41.575534 IP (id 14272, proto: TCP (6), length: 65212) 06:37:41.575544 IP (id 14312, proto: TCP (6), length: 57972) 06:37:41.575678 IP (id 14317, proto: TCP (6), length: 7292) 06:37:41.575683 IP (id 14361, proto: TCP (6), length: 63764) It appears I introduced this bug in linux-3.1. inet_getid() must return the old value of peer->ip_id_count, not the new one. Lets revert this part, and remove the prevention of a null identification field in IPv6 Fragment Extension Header, which is dubious and not even done properly. Fixes: 87c48fa3b463 ("ipv6: make fragment identifications less predictable") Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
* net: tunnels - enable module autoloadingTom Gundersen2014-07-112-0/+2
| | | | | | | | | | | | | [ Upstream commit f98f89a0104454f35a62d681683c844f6dbf4043 ] Enable the module alias hookup to allow tunnel modules to be autoloaded on demand. This is in line with how most other netdev kinds work, and will allow userspace to create tunnels without having CAP_SYS_MODULE. Signed-off-by: Tom Gundersen <teg@jklm.no> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
* ipv6: Limit mtu to 65575 bytesEric Dumazet2014-06-091-2/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | [ Upstream commit 30f78d8ebf7f514801e71b88a10c948275168518 ] Francois reported that setting big mtu on loopback device could prevent tcp sessions making progress. We do not support (yet ?) IPv6 Jumbograms and cook corrupted packets. We must limit the IPv6 MTU to (65535 + 40) bytes in theory. Tested: ifconfig lo mtu 70000 netperf -H ::1 Before patch : Throughput : 0.05 Mbits After patch : Throughput : 35484 Mbits Reported-by: Francois WELLENREITER <f.wellenreiter@gmail.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org> Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
* netfilter: Can't fail and free after table replacementThomas Graf2014-06-091-2/+4
| | | | | | | | | | | | | | | | | | | commit c58dd2dd443c26d856a168db108a0cd11c285bf3 upstream. All xtables variants suffer from the defect that the copy_to_user() to copy the counters to user memory may fail after the table has already been exchanged and thus exposed. Return an error at this point will result in freeing the already exposed table. Any subsequent packet processing will result in a kernel panic. We can't copy the counters before exposing the new tables as we want provide the counter state after the old table has been unhooked. Therefore convert this into a silent error. Cc: Florian Westphal <fw@strlen.de> Signed-off-by: Thomas Graf <tgraf@suug.ch> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
* ipv6: don't set DST_NOCOUNT for remotely added routesSabrina Dubroca2014-04-301-1/+1
| | | | | | | | | | | | | | | | commit c88507fbad8055297c1d1e21e599f46960cbee39 upstream. DST_NOCOUNT should only be used if an authorized user adds routes locally. In case of routes which are added on behalf of router advertisments this flag must not get used as it allows an unlimited number of routes getting added remotely. Signed-off-by: Sabrina Dubroca <sd@queasysnail.net> Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net> [bwh: Backported to 3.2: adjust context] Acked-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
* ipv6: some ipv6 statistic counters failed to disable bhHannes Frederic Sowa2014-04-303-8/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | [ Upstream commit 43a43b6040165f7b40b5b489fe61a4cb7f8c4980 ] After commit c15b1ccadb323ea ("ipv6: move DAD and addrconf_verify processing to workqueue") some counters are now updated in process context and thus need to disable bh before doing so, otherwise deadlocks can happen on 32-bit archs. Fabio Estevam noticed this while while mounting a NFS volume on an ARM board. As a compensation for missing this I looked after the other *_STATS_BH and found three other calls which need updating: 1) icmp6_send: ip6_fragment -> icmpv6_send -> icmp6_send (error handling) 2) ip6_push_pending_frames: rawv6_sendmsg -> rawv6_push_pending_frames -> ... (only in case of icmp protocol with raw sockets in error handling) 3) ping6_v6_sendmsg (error handling) Fixes: c15b1ccadb323ea ("ipv6: move DAD and addrconf_verify processing to workqueue") Reported-by: Fabio Estevam <festevam@gmail.com> Tested-by: Fabio Estevam <fabio.estevam@freescale.com> Cc: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
* ipv6: ip6_append_data_mtu do not handle the mtu of the second fragment properlylucien2014-04-301-8/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | [ Upstream commit e367c2d03dba4c9bcafad24688fadb79dd95b218 ] In ip6_append_data_mtu(), when the xfrm mode is not tunnel(such as transport),the ipsec header need to be added in the first fragment, so the mtu will decrease to reserve space for it, then the second fragment come, the mtu should be turn back, as the commit 0c1833797a5a6ec23ea9261d979aa18078720b74 said. however, in the commit a493e60ac4bbe2e977e7129d6d8cbb0dd236be, it use *mtu = min(*mtu, ...) to change the mtu, which lead to the new mtu is alway equal with the first fragment's. and cannot turn back. when I test through ping6 -c1 -s5000 $ip (mtu=1280): ...frag (0|1232) ESP(spi=0x00002000,seq=0xb), length 1232 ...frag (1232|1216) ...frag (2448|1216) ...frag (3664|1216) ...frag (4880|164) which should be: ...frag (0|1232) ESP(spi=0x00001000,seq=0x1), length 1232 ...frag (1232|1232) ...frag (2464|1232) ...frag (3696|1232) ...frag (4928|116) so delete the min() when change back the mtu. Signed-off-by: Xin Long <lucien.xin@gmail.com> Fixes: 75a493e60ac4bb ("ipv6: ip6_append_data_mtu did not care about pmtudisc and frag_size") Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
* ipv6: Avoid unnecessary temporary addresses being generatedHeiner Kallweit2014-04-301-1/+4
| | | | | | | | | | | | | | | | | | [ Upstream commit ecab67015ef6e3f3635551dcc9971cf363cc1cd5 ] tmp_prefered_lft is an offset to ifp->tstamp, not now. Therefore age needs to be added to the condition. Age calculation in ipv6_create_tempaddr is different from the one in addrconf_verify and doesn't consider ADDRCONF_TIMER_FUZZ_MINUS. This can cause age in ipv6_create_tempaddr to be less than the one in addrconf_verify and therefore unnecessary temporary address to be generated. Use age calculation as in addrconf_modify to avoid this. Signed-off-by: Heiner Kallweit <heiner.kallweit@web.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
* net: ip, ipv6: handle gso skbs in forwarding pathFlorian Westphal2014-04-091-1/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | commit fe6cc55f3a9a053482a76f5a6b2257cee51b4663 upstream. [ use zero netdev_feature mask to avoid backport of netif_skb_dev_features function ] Marcelo Ricardo Leitner reported problems when the forwarding link path has a lower mtu than the incoming one if the inbound interface supports GRO. Given: Host <mtu1500> R1 <mtu1200> R2 Host sends tcp stream which is routed via R1 and R2. R1 performs GRO. In this case, the kernel will fail to send ICMP fragmentation needed messages (or pkt too big for ipv6), as GSO packets currently bypass dstmtu checks in forward path. Instead, Linux tries to send out packets exceeding the mtu. When locking route MTU on Host (i.e., no ipv4 DF bit set), R1 does not fragment the packets when forwarding, and again tries to send out packets exceeding R1-R2 link mtu. This alters the forwarding dstmtu checks to take the individual gso segment lengths into account. For ipv6, we send out pkt too big error for gso if the individual segments are too big. For ipv4, we either send icmp fragmentation needed, or, if the DF bit is not set, perform software segmentation and let the output path create fragments when the packet is leaving the machine. It is not 100% correct as the error message will contain the headers of the GRO skb instead of the original/segmented one, but it seems to work fine in my (limited) tests. Eric Dumazet suggested to simply shrink mss via ->gso_size to avoid sofware segmentation. However it turns out that skb_segment() assumes skb nr_frags is related to mss size so we would BUG there. I don't want to mess with it considering Herbert and Eric disagree on what the correct behavior should be. Hannes Frederic Sowa notes that when we would shrink gso_size skb_segment would then also need to deal with the case where SKB_MAX_FRAGS would be exceeded. This uses sofware segmentation in the forward path when we hit ipv4 non-DF packets and the outgoing link mtu is too small. Its not perfect, but given the lack of bug reports wrt. GRO fwd being broken this is a rare case anyway. Also its not like this could not be improved later once the dust settles. Acked-by: Herbert Xu <herbert@gondor.apana.org.au> Reported-by: Marcelo Ricardo Leitner <mleitner@redhat.com> Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
* net: avoid reference counter overflows on fib_rules in multicast forwardingHannes Frederic Sowa2014-02-151-2/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | [ Upstream commit 95f4a45de1a0f172b35451fc52283290adb21f6e ] Bob Falken reported that after 4G packets, multicast forwarding stopped working. This was because of a rule reference counter overflow which freed the rule as soon as the overflow happend. This patch solves this by adding the FIB_LOOKUP_NOREF flag to fib_rules_lookup calls. This is safe even from non-rcu locked sections as in this case the flag only implies not taking a reference to the rule, which we don't need at all. Rules only hold references to the namespace, which are guaranteed to be available during the call of the non-rcu protected function reg_vif_xmit because of the interface reference which itself holds a reference to the net namespace. Fixes: f0ad0860d01e47 ("ipv4: ipmr: support multiple tables") Fixes: d1db275dd3f6e4 ("ipv6: ip6mr: support multiple tables") Reported-by: Bob Falken <NetFestivalHaveFun@gmx.com> Cc: Patrick McHardy <kaber@trash.net> Cc: Thomas Graf <tgraf@suug.ch> Cc: Julian Anastasov <ja@ssi.bg> Cc: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
* ipv6: don't count addrconf generated routes against gc limitHannes Frederic Sowa2014-02-151-6/+2
| | | | | | | | | | | | | | | | | | [ Upstream commit a3300ef4bbb1f1e33ff0400e1e6cf7733d988f4f ] Brett Ciphery reported that new ipv6 addresses failed to get installed because the addrconf generated dsts where counted against the dst gc limit. We don't need to count those routes like we currently don't count administratively added routes. Because the max_addresses check enforces a limit on unbounded address generation first in case someone plays with router advertisments, we are still safe here. Reported-by: Brett Ciphery <brett.ciphery@windriver.com> Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
* ipv6: fix possible seqlock deadlock in ip6_finish_output2Hannes Frederic Sowa2014-01-031-2/+2
| | | | | | | | | | | | | | [ Upstream commit 7f88c6b23afbd31545c676dea77ba9593a1a14bf ] IPv6 stats are 64 bits and thus are protected with a seqlock. By not disabling bottom-half we could deadlock here if we don't disable bh and a softirq reentrantly updates the same mib. Cc: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
* ipv6: fix leaking uninitialized port number of offender sockaddrHannes Frederic Sowa2014-01-031-0/+1
| | | | | | | | | | [ Upstream commit 1fa4c710b6fe7b0aac9907240291b6fe6aafc3b8 ] Offenders don't have port numbers, so set it to 0. Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
* inet: fix addr_len/msg->msg_namelen assignment in recv_error and rxpmtu ↵Hannes Frederic Sowa2014-01-033-6/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | functions [ Upstream commit 85fbaa75037d0b6b786ff18658ddf0b4014ce2a4 ] Commit bceaa90240b6019ed73b49965eac7d167610be69 ("inet: prevent leakage of uninitialized memory to user in recv syscalls") conditionally updated addr_len if the msg_name is written to. The recv_error and rxpmtu functions relied on the recvmsg functions to set up addr_len before. As this does not happen any more we have to pass addr_len to those functions as well and set it to the size of the corresponding sockaddr length. This broke traceroute and such. Fixes: bceaa90240b6 ("inet: prevent leakage of uninitialized memory to user in recv syscalls") Reported-by: Brad Spengler <spender@grsecurity.net> Reported-by: Tom Labanowski Cc: mpb <mpb.mail@gmail.com> Cc: David S. Miller <davem@davemloft.net> Cc: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
* inet: prevent leakage of uninitialized memory to user in recv syscallsHannes Frederic Sowa2014-01-032-7/+2
| | | | | | | | | | | | | | | | | | | [ Upstream commit bceaa90240b6019ed73b49965eac7d167610be69 ] Only update *addr_len when we actually fill in sockaddr, otherwise we can return uninitialized memory from the stack to the caller in the recvfrom, recvmmsg and recvmsg syscalls. Drop the the (addr_len == NULL) checks because we only get called with a valid addr_len pointer either from sock_common_recvmsg or inet_recvmsg. If a blocking read waits on a socket which is concurrently shut down we now return zero and set msg_msgnamelen to 0. Reported-by: mpb <mpb.mail@gmail.com> Suggested-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
* ipv6: use rt6_get_dflt_router to get default router in rt6_route_rcvDuan Jiong2014-01-031-2/+5
| | | | | | | | | | | | | | | | | | | [ Upstream commit f104a567e673f382b09542a8dc3500aa689957b4 ] As the rfc 4191 said, the Router Preference and Lifetime values in a ::/0 Route Information Option should override the preference and lifetime values in the Router Advertisement header. But when the kernel deals with a ::/0 Route Information Option, the rt6_get_route_info() always return NULL, that means that overriding will not happen, because those default routers were added without flag RTF_ROUTEINFO in rt6_add_dflt_router(). In order to deal with that condition, we should call rt6_get_dflt_router when the prefix length is 0. Signed-off-by: Duan Jiong <duanj.fnst@cn.fujitsu.com> Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
* inet: fix possible memory corruption with UDP_CORK and UFOHannes Frederic Sowa2013-11-281-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | [ This is a simplified -stable version of a set of upstream commits. ] This is a replacement patch only for stable which does fix the problems handled by the following two commits in -net: "ip_output: do skb ufo init for peeked non ufo skb as well" (e93b7d748be887cd7639b113ba7d7ef792a7efb9) "ip6_output: do skb ufo init for peeked non ufo skb as well" (c547dbf55d5f8cf615ccc0e7265e98db27d3fb8b) Three frames are written on a corked udp socket for which the output netdevice has UFO enabled. If the first and third frame are smaller than the mtu and the second one is bigger, we enqueue the second frame with skb_append_datato_frags without initializing the gso fields. This leads to the third frame appended regulary and thus constructing an invalid skb. This fixes the problem by always using skb_append_datato_frags as soon as the first frag got enqueued to the skb without marking the packet as SKB_GSO_UDP. The problem with only two frames for ipv6 was fixed by "ipv6: udp packets following an UFO enqueued packet need also be handled by UFO" (2811ebac2521ceac84f2bdae402455baa6a7fb47). Cc: Jiri Pirko <jiri@resnulli.us> Cc: Eric Dumazet <eric.dumazet@gmail.com> Cc: David Miller <davem@davemloft.net> Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
* ipv6: restrict neighbor entry creation to output flowMarcelo Ricardo Leitner2013-11-281-4/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch is based on 3.2.y branch, the one used by reporter. Please let me know if it should be different. Thanks. The patch which introduced the regression was applied on stables: 3.0.64 3.4.31 3.7.8 3.2.39 The patch which introduced the regression was for stable trees only. ---8<--- Commit 0d6a77079c475033cb622c07c5a880b392ef664e "ipv6: do not create neighbor entries for local delivery" introduced a regression on which routes to local delivery would not work anymore. Like this: $ ip -6 route add local 2001::/64 dev lo $ ping6 -c1 2001::9 PING 2001::9(2001::9) 56 data bytes ping: sendmsg: Invalid argument As this is a local delivery, that commit would not allow the creation of a neighbor entry and thus the packet cannot be sent. But as TPROXY scenario actually needs to avoid the neighbor entry creation only for input flow, this patch now limits previous patch to input flow, keeping output as before that patch. Reported-by: Debabrata Banerjee <dbavatar@gmail.com> Signed-off-by: Marcelo Ricardo Leitner <mleitner@redhat.com> Signed-off-by: Jiri Pirko <jiri@resnulli.us> Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org> CC: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
* net: do not call sock_put() on TIMEWAIT socketsEric Dumazet2013-11-281-1/+1
| | | | | | | | | | | | | [ Upstream commit 80ad1d61e72d626e30ebe8529a0455e660ca4693 ] commit 3ab5aee7fe84 ("net: Convert TCP & DCCP hash tables to use RCU / hlist_nulls") incorrectly used sock_put() on TIMEWAIT sockets. We should instead use inet_twsk_put() Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
* ipv6 mcast: use in6_dev_put in timer handlers instead of __in6_dev_putSalam Noureddine2013-10-261-2/+2
| | | | | | | | | | | | | | | | | | | [ Upstream commit 9260d3e1013701aa814d10c8fc6a9f92bd17d643 ] It is possible for the timer handlers to run after the call to ipv6_mc_down so use in6_dev_put instead of __in6_dev_put in the handler function in order to do proper cleanup when the refcnt reaches 0. Otherwise, the refcnt can reach zero without the inet6_dev being destroyed and we end up leaking a reference to the net_device and see messages like the following, unregister_netdevice: waiting for eth0 to become free. Usage count = 1 Tested on linux-3.4.43. Signed-off-by: Salam Noureddine <noureddine@aristanetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
* ipv6: udp packets following an UFO enqueued packet need also be handled by UFOHannes Frederic Sowa2013-10-261-31/+22
| | | | | | | | | | | | | | | | | | | | | | | | | | [ Upstream commit 2811ebac2521ceac84f2bdae402455baa6a7fb47 ] In the following scenario the socket is corked: If the first UDP packet is larger then the mtu we try to append it to the write queue via ip6_ufo_append_data. A following packet, which is smaller than the mtu would be appended to the already queued up gso-skb via plain ip6_append_data. This causes random memory corruptions. In ip6_ufo_append_data we also have to be careful to not queue up the same skb multiple times. So setup the gso frame only when no first skb is available. This also fixes a shortcoming where we add the current packet's length to cork->length but return early because of a packet > mtu with dontfrag set (instead of sutracting it again). Found with trinity. Cc: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org> Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Reported-by: Dmitry Vyukov <dvyukov@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
* ICMPv6: treat dest unreachable codes 5 and 6 as EACCES, not EPROTOJiri Bohac2013-10-261-1/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | [ Upstream commit 61e76b178dbe7145e8d6afa84bb4ccea71918994 ] RFC 4443 has defined two additional codes for ICMPv6 type 1 (destination unreachable) messages: 5 - Source address failed ingress/egress policy 6 - Reject route to destination Now they are treated as protocol error and icmpv6_err_convert() converts them to EPROTO. RFC 4443 says: "Codes 5 and 6 are more informative subsets of code 1." Treat codes 5 and 6 as code 1 (EACCES) Btw, connect() returning -EPROTO confuses firefox, so that fallback to other/IPv4 addresses does not work: https://bugzilla.mozilla.org/show_bug.cgi?id=910773 Signed-off-by: Jiri Bohac <jbohac@suse.cz> Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
* ipv6: Don't depend on per socket memory for neighbour discovery messagesThomas Graf2013-10-261-7/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | [ Upstream commit 25a6e6b84fba601eff7c28d30da8ad7cfbef0d43 ] Allocating skbs when sending out neighbour discovery messages currently uses sock_alloc_send_skb() based on a per net namespace socket and thus share a socket wmem buffer space. If a netdevice is temporarily unable to transmit due to carrier loss or for other reasons, the queued up ndisc messages will cosnume all of the wmem space and will thus prevent from any more skbs to be allocated even for netdevices that are able to transmit packets. The number of neighbour discovery messages sent is very limited, use of alloc_skb() bypasses the socket wmem buffer size enforcement while the manual call to skb_set_owner_w() maintains the socket reference needed for the IPv6 output path. This patch has orginally been posted by Eric Dumazet in a modified form. Signed-off-by: Thomas Graf <tgraf@suug.ch> Cc: Eric Dumazet <eric.dumazet@gmail.com> Cc: Hannes Frederic Sowa <hannes@stressinduktion.org> Cc: Stephen Warren <swarren@wwwdotorg.org> Cc: Fabio Estevam <festevam@gmail.com> Tested-by: Fabio Estevam <fabio.estevam@freescale.com> Tested-by: Stephen Warren <swarren@nvidia.com> Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
* ipv6: drop packets with multiple fragmentation headersHannes Frederic Sowa2013-10-261-0/+5
| | | | | | | | | | | | | | | | [ Upstream commit f46078cfcd77fa5165bf849f5e568a7ac5fa569c ] It is not allowed for an ipv6 packet to contain multiple fragmentation headers. So discard packets which were already reassembled by fragmentation logic and send back a parameter problem icmp. The updates for RFC 6980 will come in later, I have to do a bit more research here. Cc: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org> Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
* ipv6: remove max_addresses check from ipv6_create_tempaddrHannes Frederic Sowa2013-10-261-6/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | [ Upstream commit 4b08a8f1bd8cb4541c93ec170027b4d0782dab52 ] Because of the max_addresses check attackers were able to disable privacy extensions on an interface by creating enough autoconfigured addresses: <http://seclists.org/oss-sec/2012/q4/292> But the check is not actually needed: max_addresses protects the kernel to install too many ipv6 addresses on an interface and guards addrconf_prefix_rcv to install further addresses as soon as this limit is reached. We only generate temporary addresses in direct response of a new address showing up. As soon as we filled up the maximum number of addresses of an interface, we stop installing more addresses and thus also stop generating more temp addresses. Even if the attacker tries to generate a lot of temporary addresses by announcing a prefix and removing it again (lifetime == 0) we won't install more temp addresses, because the temporary addresses do count to the maximum number of addresses, thus we would stop installing new autoconfigured addresses when the limit is reached. This patch fixes CVE-2013-0343 (but other layer-2 attacks are still possible). Thanks to Ding Tianhong to bring this topic up again. Cc: Ding Tianhong <dingtianhong@huawei.com> Cc: George Kargiotakis <kargig@void.gr> Cc: P J P <ppandit@redhat.com> Cc: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org> Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Acked-by: Ding Tianhong <dingtianhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
* ipv6: don't stop backtracking in fib6_lookup_1 if subtree does not matchHannes Frederic Sowa2013-10-261-4/+12
| | | | | | | | | | | | | | | | | | | | | [ Upstream commit 3e3be275851bc6fc90bfdcd732cd95563acd982b ] In case a subtree did not match we currently stop backtracking and return NULL (root table from fib_lookup). This could yield in invalid routing table lookups when using subtrees. Instead continue to backtrack until a valid subtree or node is found and return this match. Also remove unneeded NULL check. Reported-by: Teco Boot <teco@inf-net.nl> Cc: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org> Cc: David Lamparter <equinox@diac24.net> Cc: <boutier@pps.univ-paris-diderot.fr> Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
* ipv6: take rtnl_lock and mark mrt6 table as freed on namespace cleanupHannes Frederic Sowa2013-09-101-0/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | [ Upstream commit 905a6f96a1b18e490a75f810d733ced93c39b0e5 ] Otherwise we end up dereferencing the already freed net->ipv6.mrt pointer which leads to a panic (from Srivatsa S. Bhat): BUG: unable to handle kernel paging request at ffff882018552020 IP: [<ffffffffa0366b02>] ip6mr_sk_done+0x32/0xb0 [ipv6] PGD 290a067 PUD 207ffe0067 PMD 207ff1d067 PTE 8000002018552060 Oops: 0000 [#1] SMP DEBUG_PAGEALLOC Modules linked in: ebtable_nat ebtables nfs fscache nf_conntrack_ipv4 nf_defrag_ipv4 ipt_REJECT xt_CHECKSUM iptable_mangle iptable_filter ip_tables nfsd lockd nfs_acl exportfs auth_rpcgss autofs4 sunrpc 8021q garp bridge stp llc ip6t_REJECT nf_conntrack_ipv6 nf_defrag_ipv6 xt_state nf_conntrack ip6table_filter +ip6_tables ipv6 vfat fat vhost_net macvtap macvlan vhost tun kvm_intel kvm uinput iTCO_wdt iTCO_vendor_support cdc_ether usbnet mii microcode i2c_i801 i2c_core lpc_ich mfd_core shpchp ioatdma dca mlx4_core be2net wmi acpi_cpufreq mperf ext4 jbd2 mbcache dm_mirror dm_region_hash dm_log dm_mod CPU: 0 PID: 7 Comm: kworker/u33:0 Not tainted 3.11.0-rc1-ea45e-a #4 Hardware name: IBM -[8737R2A]-/00Y2738, BIOS -[B2E120RUS-1.20]- 11/30/2012 Workqueue: netns cleanup_net task: ffff8810393641c0 ti: ffff881039366000 task.ti: ffff881039366000 RIP: 0010:[<ffffffffa0366b02>] [<ffffffffa0366b02>] ip6mr_sk_done+0x32/0xb0 [ipv6] RSP: 0018:ffff881039367bd8 EFLAGS: 00010286 RAX: ffff881039367fd8 RBX: ffff882018552000 RCX: dead000000200200 RDX: 0000000000000000 RSI: ffff881039367b68 RDI: ffff881039367b68 RBP: ffff881039367bf8 R08: ffff881039367b68 R09: 2222222222222222 R10: 2222222222222222 R11: 2222222222222222 R12: ffff882015a7a040 R13: ffff882014eb89c0 R14: ffff8820289e2800 R15: 0000000000000000 FS: 0000000000000000(0000) GS:ffff88103fc00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: ffff882018552020 CR3: 0000000001c0b000 CR4: 00000000000407f0 Stack: ffff881039367c18 ffff882014eb89c0 ffff882015e28c00 0000000000000000 ffff881039367c18 ffffffffa034d9d1 ffff8820289e2800 ffff882014eb89c0 ffff881039367c58 ffffffff815bdecb ffffffff815bddf2 ffff882014eb89c0 Call Trace: [<ffffffffa034d9d1>] rawv6_close+0x21/0x40 [ipv6] [<ffffffff815bdecb>] inet_release+0xfb/0x220 [<ffffffff815bddf2>] ? inet_release+0x22/0x220 [<ffffffffa032686f>] inet6_release+0x3f/0x50 [ipv6] [<ffffffff8151c1d9>] sock_release+0x29/0xa0 [<ffffffff81525520>] sk_release_kernel+0x30/0x70 [<ffffffffa034f14b>] icmpv6_sk_exit+0x3b/0x80 [ipv6] [<ffffffff8152fff9>] ops_exit_list+0x39/0x60 [<ffffffff815306fb>] cleanup_net+0xfb/0x1a0 [<ffffffff81075e3a>] process_one_work+0x1da/0x610 [<ffffffff81075dc9>] ? process_one_work+0x169/0x610 [<ffffffff81076390>] worker_thread+0x120/0x3a0 [<ffffffff81076270>] ? process_one_work+0x610/0x610 [<ffffffff8107da2e>] kthread+0xee/0x100 [<ffffffff8107d940>] ? __init_kthread_worker+0x70/0x70 [<ffffffff8162a99c>] ret_from_fork+0x7c/0xb0 [<ffffffff8107d940>] ? __init_kthread_worker+0x70/0x70 Code: 20 48 89 5d e8 4c 89 65 f0 4c 89 6d f8 66 66 66 66 90 4c 8b 67 30 49 89 fd e8 db 3c 1e e1 49 8b 9c 24 90 08 00 00 48 85 db 74 06 <4c> 39 6b 20 74 20 bb f3 ff ff ff e8 8e 3c 1e e1 89 d8 4c 8b 65 RIP [<ffffffffa0366b02>] ip6mr_sk_done+0x32/0xb0 [ipv6] RSP <ffff881039367bd8> CR2: ffff882018552020 Reported-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com> Tested-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com> Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
* ipv6: ip6_append_data_mtu did not care about pmtudisc and frag_sizeHannes Frederic Sowa2013-08-021-6/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | [ Upstream commit 75a493e60ac4bbe2e977e7129d6d8cbb0dd236be ] If the socket had an IPV6_MTU value set, ip6_append_data_mtu lost track of this when appending the second frame on a corked socket. This results in the following splat: [37598.993962] ------------[ cut here ]------------ [37598.994008] kernel BUG at net/core/skbuff.c:2064! [37598.994008] invalid opcode: 0000 [#1] SMP [37598.994008] Modules linked in: tcp_lp uvcvideo videobuf2_vmalloc videobuf2_memops videobuf2_core videodev media vfat fat usb_storage fuse ebtable_nat xt_CHECKSUM bridge stp llc ipt_MASQUERADE nf_conntrack_netbios_ns nf_conntrack_broadcast ip6table_mangle ip6t_REJECT nf_conntrack_ipv6 nf_defrag_ipv6 iptable_nat +nf_nat_ipv4 nf_nat iptable_mangle nf_conntrack_ipv4 nf_defrag_ipv4 xt_conntrack nf_conntrack ebtable_filter ebtables ip6table_filter ip6_tables be2iscsi iscsi_boot_sysfs bnx2i cnic uio cxgb4i cxgb4 cxgb3i cxgb3 mdio libcxgbi ib_iser rdma_cm ib_addr iw_cm ib_cm ib_sa ib_mad ib_core iscsi_tcp libiscsi_tcp libiscsi +scsi_transport_iscsi rfcomm bnep iTCO_wdt iTCO_vendor_support snd_hda_codec_conexant arc4 iwldvm mac80211 snd_hda_intel acpi_cpufreq mperf coretemp snd_hda_codec microcode cdc_wdm cdc_acm [37598.994008] snd_hwdep cdc_ether snd_seq snd_seq_device usbnet mii joydev btusb snd_pcm bluetooth i2c_i801 e1000e lpc_ich mfd_core ptp iwlwifi pps_core snd_page_alloc mei cfg80211 snd_timer thinkpad_acpi snd tpm_tis soundcore rfkill tpm tpm_bios vhost_net tun macvtap macvlan kvm_intel kvm uinput binfmt_misc +dm_crypt i915 i2c_algo_bit drm_kms_helper drm i2c_core wmi video [37598.994008] CPU 0 [37598.994008] Pid: 27320, comm: t2 Not tainted 3.9.6-200.fc18.x86_64 #1 LENOVO 27744PG/27744PG [37598.994008] RIP: 0010:[<ffffffff815443a5>] [<ffffffff815443a5>] skb_copy_and_csum_bits+0x325/0x330 [37598.994008] RSP: 0018:ffff88003670da18 EFLAGS: 00010202 [37598.994008] RAX: ffff88018105c018 RBX: 0000000000000004 RCX: 00000000000006c0 [37598.994008] RDX: ffff88018105a6c0 RSI: ffff88018105a000 RDI: ffff8801e1b0aa00 [37598.994008] RBP: ffff88003670da78 R08: 0000000000000000 R09: ffff88018105c040 [37598.994008] R10: ffff8801e1b0aa00 R11: 0000000000000000 R12: 000000000000fff8 [37598.994008] R13: 00000000000004fc R14: 00000000ffff0504 R15: 0000000000000000 [37598.994008] FS: 00007f28eea59740(0000) GS:ffff88023bc00000(0000) knlGS:0000000000000000 [37598.994008] CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b [37598.994008] CR2: 0000003d935789e0 CR3: 00000000365cb000 CR4: 00000000000407f0 [37598.994008] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [37598.994008] DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400 [37598.994008] Process t2 (pid: 27320, threadinfo ffff88003670c000, task ffff88022c162ee0) [37598.994008] Stack: [37598.994008] ffff88022e098a00 ffff88020f973fc0 0000000000000008 00000000000004c8 [37598.994008] ffff88020f973fc0 00000000000004c4 ffff88003670da78 ffff8801e1b0a200 [37598.994008] 0000000000000018 00000000000004c8 ffff88020f973fc0 00000000000004c4 [37598.994008] Call Trace: [37598.994008] [<ffffffff815fc21f>] ip6_append_data+0xccf/0xfe0 [37598.994008] [<ffffffff8158d9f0>] ? ip_copy_metadata+0x1a0/0x1a0 [37598.994008] [<ffffffff81661f66>] ? _raw_spin_lock_bh+0x16/0x40 [37598.994008] [<ffffffff8161548d>] udpv6_sendmsg+0x1ed/0xc10 [37598.994008] [<ffffffff812a2845>] ? sock_has_perm+0x75/0x90 [37598.994008] [<ffffffff815c3693>] inet_sendmsg+0x63/0xb0 [37598.994008] [<ffffffff812a2973>] ? selinux_socket_sendmsg+0x23/0x30 [37598.994008] [<ffffffff8153a450>] sock_sendmsg+0xb0/0xe0 [37598.994008] [<ffffffff810135d1>] ? __switch_to+0x181/0x4a0 [37598.994008] [<ffffffff8153d97d>] sys_sendto+0x12d/0x180 [37598.994008] [<ffffffff810dfb64>] ? __audit_syscall_entry+0x94/0xf0 [37598.994008] [<ffffffff81020ed1>] ? syscall_trace_enter+0x231/0x240 [37598.994008] [<ffffffff8166a7e7>] tracesys+0xdd/0xe2 [37598.994008] Code: fe 07 00 00 48 c7 c7 04 28 a6 81 89 45 a0 4c 89 4d b8 44 89 5d a8 e8 1b ac b1 ff 44 8b 5d a8 4c 8b 4d b8 8b 45 a0 e9 cf fe ff ff <0f> 0b 66 0f 1f 84 00 00 00 00 00 66 66 66 66 90 55 48 89 e5 48 [37598.994008] RIP [<ffffffff815443a5>] skb_copy_and_csum_bits+0x325/0x330 [37598.994008] RSP <ffff88003670da18> [37599.007323] ---[ end trace d69f6a17f8ac8eee ]--- While there, also check if path mtu discovery is activated for this socket. The logic was adapted from ip6_append_data when first writing on the corked socket. This bug was introduced with commit 0c1833797a5a6ec23ea9261d979aa18078720b74 ("ipv6: fix incorrect ipsec fragment"). v2: a) Replace IPV6_PMTU_DISC_DO with IPV6_PMTUDISC_PROBE. b) Don't pass ipv6_pinfo to ip6_append_data_mtu (suggestion by Gao feng, thanks!). c) Change mtu to unsigned int, else we get a warning about non-matching types because of the min()-macro type-check. Acked-by: Gao feng <gaofeng@cn.fujitsu.com> Cc: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org> Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
* ipv6: call udp_push_pending_frames when uncorking a socket with AF_INET ↵Hannes Frederic Sowa2013-08-021-1/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | pending data [ Upstream commit 8822b64a0fa64a5dd1dfcf837c5b0be83f8c05d1 ] We accidentally call down to ip6_push_pending_frames when uncorking pending AF_INET data on a ipv6 socket. This results in the following splat (from Dave Jones): skbuff: skb_under_panic: text:ffffffff816765f6 len:48 put:40 head:ffff88013deb6df0 data:ffff88013deb6dec tail:0x2c end:0xc0 dev:<NULL> ------------[ cut here ]------------ kernel BUG at net/core/skbuff.c:126! invalid opcode: 0000 [#1] PREEMPT SMP DEBUG_PAGEALLOC Modules linked in: dccp_ipv4 dccp 8021q garp bridge stp dlci mpoa snd_seq_dummy sctp fuse hidp tun bnep nfnetlink scsi_transport_iscsi rfcomm can_raw can_bcm af_802154 appletalk caif_socket can caif ipt_ULOG x25 rose af_key pppoe pppox ipx phonet irda llc2 ppp_generic slhc p8023 psnap p8022 llc crc_ccitt atm bluetooth +netrom ax25 nfc rfkill rds af_rxrpc coretemp hwmon kvm_intel kvm crc32c_intel snd_hda_codec_realtek ghash_clmulni_intel microcode pcspkr snd_hda_codec_hdmi snd_hda_intel snd_hda_codec snd_hwdep usb_debug snd_seq snd_seq_device snd_pcm e1000e snd_page_alloc snd_timer ptp snd pps_core soundcore xfs libcrc32c CPU: 2 PID: 8095 Comm: trinity-child2 Not tainted 3.10.0-rc7+ #37 task: ffff8801f52c2520 ti: ffff8801e6430000 task.ti: ffff8801e6430000 RIP: 0010:[<ffffffff816e759c>] [<ffffffff816e759c>] skb_panic+0x63/0x65 RSP: 0018:ffff8801e6431de8 EFLAGS: 00010282 RAX: 0000000000000086 RBX: ffff8802353d3cc0 RCX: 0000000000000006 RDX: 0000000000003b90 RSI: ffff8801f52c2ca0 RDI: ffff8801f52c2520 RBP: ffff8801e6431e08 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000001 R11: 0000000000000001 R12: ffff88022ea0c800 R13: ffff88022ea0cdf8 R14: ffff8802353ecb40 R15: ffffffff81cc7800 FS: 00007f5720a10740(0000) GS:ffff880244c00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000005862000 CR3: 000000022843c000 CR4: 00000000001407e0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000600 Stack: ffff88013deb6dec 000000000000002c 00000000000000c0 ffffffff81a3f6e4 ffff8801e6431e18 ffffffff8159a9aa ffff8801e6431e90 ffffffff816765f6 ffffffff810b756b 0000000700000002 ffff8801e6431e40 0000fea9292aa8c0 Call Trace: [<ffffffff8159a9aa>] skb_push+0x3a/0x40 [<ffffffff816765f6>] ip6_push_pending_frames+0x1f6/0x4d0 [<ffffffff810b756b>] ? mark_held_locks+0xbb/0x140 [<ffffffff81694919>] udp_v6_push_pending_frames+0x2b9/0x3d0 [<ffffffff81694660>] ? udplite_getfrag+0x20/0x20 [<ffffffff8162092a>] udp_lib_setsockopt+0x1aa/0x1f0 [<ffffffff811cc5e7>] ? fget_light+0x387/0x4f0 [<ffffffff816958a4>] udpv6_setsockopt+0x34/0x40 [<ffffffff815949f4>] sock_common_setsockopt+0x14/0x20 [<ffffffff81593c31>] SyS_setsockopt+0x71/0xd0 [<ffffffff816f5d54>] tracesys+0xdd/0xe2 Code: 00 00 48 89 44 24 10 8b 87 d8 00 00 00 48 89 44 24 08 48 8b 87 e8 00 00 00 48 c7 c7 c0 04 aa 81 48 89 04 24 31 c0 e8 e1 7e ff ff <0f> 0b 55 48 89 e5 0f 0b 55 48 89 e5 0f 0b 55 48 89 e5 0f 0b 55 RIP [<ffffffff816e759c>] skb_panic+0x63/0x65 RSP <ffff8801e6431de8> This patch adds a check if the pending data is of address family AF_INET and directly calls udp_push_ending_frames from udp_v6_push_pending_frames if that is the case. This bug was found by Dave Jones with trinity. (Also move the initialization of fl6 below the AF_INET check, even if not strictly necessary.) Cc: Dave Jones <davej@redhat.com> Cc: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org> Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
* ipv6,mcast: always hold idev->lock before mca_lockAmerigo Wang2013-08-022-18/+28
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | [ Upstream commit 8965779d2c0e6ab246c82a405236b1fb2adae6b2, with some bits from commit b7b1bfce0bb68bd8f6e62a28295922785cc63781 ("ipv6: split duplicate address detection and router solicitation timer") to get the __ipv6_get_lladdr() used by this patch. ] dingtianhong reported the following deadlock detected by lockdep: ====================================================== [ INFO: possible circular locking dependency detected ] 3.4.24.05-0.1-default #1 Not tainted ------------------------------------------------------- ksoftirqd/0/3 is trying to acquire lock: (&ndev->lock){+.+...}, at: [<ffffffff8147f804>] ipv6_get_lladdr+0x74/0x120 but task is already holding lock: (&mc->mca_lock){+.+...}, at: [<ffffffff8149d130>] mld_send_report+0x40/0x150 which lock already depends on the new lock. the existing dependency chain (in reverse order) is: -> #1 (&mc->mca_lock){+.+...}: [<ffffffff810a8027>] validate_chain+0x637/0x730 [<ffffffff810a8417>] __lock_acquire+0x2f7/0x500 [<ffffffff810a8734>] lock_acquire+0x114/0x150 [<ffffffff814f691a>] rt_spin_lock+0x4a/0x60 [<ffffffff8149e4bb>] igmp6_group_added+0x3b/0x120 [<ffffffff8149e5d8>] ipv6_mc_up+0x38/0x60 [<ffffffff81480a4d>] ipv6_find_idev+0x3d/0x80 [<ffffffff81483175>] addrconf_notify+0x3d5/0x4b0 [<ffffffff814fae3f>] notifier_call_chain+0x3f/0x80 [<ffffffff81073471>] raw_notifier_call_chain+0x11/0x20 [<ffffffff813d8722>] call_netdevice_notifiers+0x32/0x60 [<ffffffff813d92d4>] __dev_notify_flags+0x34/0x80 [<ffffffff813d9360>] dev_change_flags+0x40/0x70 [<ffffffff813ea627>] do_setlink+0x237/0x8a0 [<ffffffff813ebb6c>] rtnl_newlink+0x3ec/0x600 [<ffffffff813eb4d0>] rtnetlink_rcv_msg+0x160/0x310 [<ffffffff814040b9>] netlink_rcv_skb+0x89/0xb0 [<ffffffff813eb357>] rtnetlink_rcv+0x27/0x40 [<ffffffff81403e20>] netlink_unicast+0x140/0x180 [<ffffffff81404a9e>] netlink_sendmsg+0x33e/0x380 [<ffffffff813c4252>] sock_sendmsg+0x112/0x130 [<ffffffff813c537e>] __sys_sendmsg+0x44e/0x460 [<ffffffff813c5544>] sys_sendmsg+0x44/0x70 [<ffffffff814feab9>] system_call_fastpath+0x16/0x1b -> #0 (&ndev->lock){+.+...}: [<ffffffff810a798e>] check_prev_add+0x3de/0x440 [<ffffffff810a8027>] validate_chain+0x637/0x730 [<ffffffff810a8417>] __lock_acquire+0x2f7/0x500 [<ffffffff810a8734>] lock_acquire+0x114/0x150 [<ffffffff814f6c82>] rt_read_lock+0x42/0x60 [<ffffffff8147f804>] ipv6_get_lladdr+0x74/0x120 [<ffffffff8149b036>] mld_newpack+0xb6/0x160 [<ffffffff8149b18b>] add_grhead+0xab/0xc0 [<ffffffff8149d03b>] add_grec+0x3ab/0x460 [<ffffffff8149d14a>] mld_send_report+0x5a/0x150 [<ffffffff8149f99e>] igmp6_timer_handler+0x4e/0xb0 [<ffffffff8105705a>] call_timer_fn+0xca/0x1d0 [<ffffffff81057b9f>] run_timer_softirq+0x1df/0x2e0 [<ffffffff8104e8c7>] handle_pending_softirqs+0xf7/0x1f0 [<ffffffff8104ea3b>] __do_softirq_common+0x7b/0xf0 [<ffffffff8104f07f>] __thread_do_softirq+0x1af/0x210 [<ffffffff8104f1c1>] run_ksoftirqd+0xe1/0x1f0 [<ffffffff8106c7de>] kthread+0xae/0xc0 [<ffffffff814fff74>] kernel_thread_helper+0x4/0x10 actually we can just hold idev->lock before taking pmc->mca_lock, and avoid taking idev->lock again when iterating idev->addr_list, since the upper callers of mld_newpack() already take read_lock_bh(&idev->lock). Reported-by: dingtianhong <dingtianhong@huawei.com> Cc: dingtianhong <dingtianhong@huawei.com> Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org> Cc: David S. Miller <davem@davemloft.net> Cc: Hannes Frederic Sowa <hannes@stressinduktion.org> Tested-by: Ding Tianhong <dingtianhong@huawei.com> Tested-by: Chen Weilong <chenweilong@huawei.com> Signed-off-by: Cong Wang <amwang@redhat.com> Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
* ipv6: ip6_sk_dst_check() must not assume ipv6 dstEric Dumazet2013-08-021-1/+7
| | | | | | | | | | | | | | | | | | | | | | | [ Upstream commit a963a37d384d71ad43b3e9e79d68d42fbe0901f3 ] It's possible to use AF_INET6 sockets and to connect to an IPv4 destination. After this, socket dst cache is a pointer to a rtable, not rt6_info. ip6_sk_dst_check() should check the socket dst cache is IPv6, or else various corruptions/crashes can happen. Dave Jones can reproduce immediate crash with trinity -q -l off -n -c sendmsg -c connect With help from Hannes Frederic Sowa Reported-by: Dave Jones <davej@redhat.com> Reported-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: Eric Dumazet <edumazet@google.com> Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
generated by cgit v1.1 at 2024-05-19 05:46:28 +0000