From a0ba4332a2cb110d6ef7695e64887396ab7d09d6 Mon Sep 17 00:00:00 2001 From: Greg Ungerer Date: Sun, 6 Mar 2011 00:20:01 +1000 Subject: m68knommu: remove use of MBAR value for ColdFire 528x peripheral addressing The ColdFire 528x family of CPUs does not have an MBAR register, so don't define its peripheral addresses relative to one. Its internal peripherals are relative to the IPSBAR register, so make sure to use that. Signed-off-by: Greg Ungerer --- arch/m68k/include/asm/m528xsim.h | 12 +++++++++--- arch/m68knommu/platform/528x/config.c | 14 +++++++------- 2 files changed, 16 insertions(+), 10 deletions(-) diff --git a/arch/m68k/include/asm/m528xsim.h b/arch/m68k/include/asm/m528xsim.h index 014098a..d7c9241 100644 --- a/arch/m68k/include/asm/m528xsim.h +++ b/arch/m68k/include/asm/m528xsim.h @@ -49,9 +49,15 @@ /* * UART module. */ -#define MCFUART_BASE1 0x200 /* Base address of UART1 */ -#define MCFUART_BASE2 0x240 /* Base address of UART2 */ -#define MCFUART_BASE3 0x280 /* Base address of UART3 */ +#define MCFUART_BASE1 (MCF_IPSBAR + 0x00000200) +#define MCFUART_BASE2 (MCF_IPSBAR + 0x00000240) +#define MCFUART_BASE3 (MCF_IPSBAR + 0x00000280) + +/* + * FEC ethernet module. + */ +#define MCFFEC_BASE (MCF_IPSBAR + 0x00001000) +#define MCFFEC_SIZE 0x800 /* * GPIO registers diff --git a/arch/m68knommu/platform/528x/config.c b/arch/m68knommu/platform/528x/config.c index 76b7433..ac39fc6 100644 --- a/arch/m68knommu/platform/528x/config.c +++ b/arch/m68knommu/platform/528x/config.c @@ -29,15 +29,15 @@ static struct mcf_platform_uart m528x_uart_platform[] = { { - .mapbase = MCF_MBAR + MCFUART_BASE1, + .mapbase = MCFUART_BASE1, .irq = MCFINT_VECBASE + MCFINT_UART0, }, { - .mapbase = MCF_MBAR + MCFUART_BASE2, + .mapbase = MCFUART_BASE2, .irq = MCFINT_VECBASE + MCFINT_UART0 + 1, }, { - .mapbase = MCF_MBAR + MCFUART_BASE3, + .mapbase = MCFUART_BASE3, .irq = MCFINT_VECBASE + MCFINT_UART0 + 2, }, { }, @@ -51,8 +51,8 @@ static struct platform_device m528x_uart = { static struct resource m528x_fec_resources[] = { { - .start = MCF_MBAR + 0x1000, - .end = MCF_MBAR + 0x1000 + 0x7ff, + .start = MCFFEC_BASE, + .end = MCFFEC_BASE + MCFFEC_SIZE - 1, .flags = IORESOURCE_MEM, }, { @@ -227,9 +227,9 @@ static void __init m528x_uart_init_line(int line, int irq) /* make sure PUAPAR is set for UART0 and UART1 */ if (line < 2) { - port = readb(MCF_MBAR + MCF5282_GPIO_PUAPAR); + port = readb(MCF5282_GPIO_PUAPAR); port |= (0x03 << (line * 2)); - writeb(port, MCF_MBAR + MCF5282_GPIO_PUAPAR); + writeb(port, MCF5282_GPIO_PUAPAR); } } -- cgit v1.1