From 400b48ecd95a7fac6b126042d37b7efe0202b582 Mon Sep 17 00:00:00 2001 From: Jean Delvare Date: Thu, 23 Mar 2006 16:46:47 +0100 Subject: [PATCH] hwmon: Add sysfs interface for individual alarm files Extend the sysfs interface of hardware monitoring chips, by adding individual alarm and beep files. Contrary to the old aggregated "alarms" and "beeps" files, individual files constitute a standard way to access the status information, making it finally possible to implement a chip-independant hardware monitoring chip access library (once all drivers have been added this new interface, that is.) If future drivers need more individual files, the interface will be extended as needed at the same time these drivers are merged into the kernel tree. Signed-off-by: Jean Delvare Signed-off-by: Greg Kroah-Hartman --- Documentation/hwmon/sysfs-interface | 98 +++++++++++++++++++++++++++---------- 1 file changed, 73 insertions(+), 25 deletions(-) (limited to 'Documentation') diff --git a/Documentation/hwmon/sysfs-interface b/Documentation/hwmon/sysfs-interface index 2d16e1e..eeb9122 100644 --- a/Documentation/hwmon/sysfs-interface +++ b/Documentation/hwmon/sysfs-interface @@ -252,9 +252,68 @@ curr[1-n]_input Current input value Read only. -********* -* Other * -********* +********** +* Alarms * +********** + +Each channel or limit may have an associated alarm file, containing a +boolean value. 1 means than an alarm condition exists, 0 means no alarm. + +Usually a given chip will either use channel-related alarms, or +limit-related alarms, not both. The driver should just reflect the hardware +implementation. + +in[0-n]_alarm +fan[1-n]_alarm +temp[1-n]_alarm + Channel alarm + Boolean + Read-only + +OR + +in[0-n]_min_alarm +in[0-n]_max_alarm +fan[1-n]_min_alarm +temp[1-n]_min_alarm +temp[1-n]_max_alarm +temp[1-n]_crit_alarm + Limit alarm + Boolean + Read-only + +Each input channel may have an associated fault file. This can be used +to notify open diodes, unconnected fans etc. where the hardware +supports it. When this boolean has value 1, the measurement for that +channel should not be trusted. + +in[0-n]_input_fault +fan[1-n]_input_fault +temp[1-n]_input_fault + Input fault condition + Boolean + Read-only + +Some chips also offer the possibility to get beeped when an alarm occurs: + +beep_enable Master beep enable + Boolean + Read/Write + +in[0-n]_beep +fan[1-n]_beep +temp[1-n]_beep + Channel beep + 0 to disable. + 1 to enable. + Read/write + +In theory, a chip could provide per-limit beep masking, but no such chip +was seen so far. + +Old drivers provided a different, non-standard interface to alarms and +beeps. These interface files are deprecated, but will be kept around +for compatibility reasons: alarms Alarm bitmask. Read only. @@ -265,33 +324,22 @@ alarms Alarm bitmask. if it is still valid. Generally a direct representation of a chip's internal alarm registers; there is no standard for the position - of individual bits. + of individual bits. For this reason, the use of this + interface file for new drivers is discouraged. Use + individual *_alarm and *_fault files instead. Bits are defined in kernel/include/sensors.h. -alarms_in Alarm bitmask relative to in (voltage) channels - Read only - A '1' bit means an alarm, LSB corresponds to in0 and so on - Prefered to 'alarms' for newer chips - -alarms_fan Alarm bitmask relative to fan channels - Read only - A '1' bit means an alarm, LSB corresponds to fan1 and so on - Prefered to 'alarms' for newer chips - -alarms_temp Alarm bitmask relative to temp (temperature) channels - Read only - A '1' bit means an alarm, LSB corresponds to temp1 and so on - Prefered to 'alarms' for newer chips - -beep_enable Beep/interrupt enable - 0 to disable. - 1 to enable. - Read/Write - beep_mask Bitmask for beep. - Same format as 'alarms' with the same bit locations. + Same format as 'alarms' with the same bit locations, + use discouraged for the same reason. Use individual + *_beep files instead. Read/Write + +********* +* Other * +********* + eeprom Raw EEPROM data in binary form. Read only. -- cgit v1.1