From 65d916d95314566f426cc40ff0f17b754a773b0b Mon Sep 17 00:00:00 2001 From: Edward Hsu Date: Fri, 17 Aug 2007 10:14:36 +0200 Subject: r8169: correct phy parameters for the 8110SC The phys of the 8110SC (RTL_GIGA_MAC_VER_{05/06}) act abnormally in gigabit mode if they are applied the parameters in rtl8169_hw_phy_config which actually aim the 8110S/SB. It is ok to return early from rtl8169_hw_phy_config as it does not apply to the 8101 and 8168 families. Signed-off-by: Edward Hsu Signed-off-by: Francois Romieu --- drivers/net/r8169.c | 5 ++++- 1 file changed, 4 insertions(+), 1 deletion(-) (limited to 'drivers/net') diff --git a/drivers/net/r8169.c b/drivers/net/r8169.c index b85ab4a..d9bb51b 100644 --- a/drivers/net/r8169.c +++ b/drivers/net/r8169.c @@ -1228,7 +1228,10 @@ static void rtl8169_hw_phy_config(struct net_device *dev) return; } - /* phy config for RTL8169s mac_version C chip */ + if ((tp->mac_version != RTL_GIGA_MAC_VER_02) && + (tp->mac_version != RTL_GIGA_MAC_VER_03)) + return; + mdio_write(ioaddr, 31, 0x0001); //w 31 2 0 1 mdio_write(ioaddr, 21, 0x1000); //w 21 15 0 1000 mdio_write(ioaddr, 24, 0x65c7); //w 24 15 0 65c7 -- cgit v1.1 From d78ae2dcc2acebb9a1048278f47f762c069db75c Mon Sep 17 00:00:00 2001 From: Francois Romieu Date: Sun, 26 Aug 2007 20:08:19 +0200 Subject: r8169: workaround against ignored TxPoll writes (8168) The 8168 ignores the requests to fetch the Tx descriptors when the relevant TxPoll bit is already set. It easily kills the performances of the 8168. David Gundersen has noticed that it is enough to wait for the completion of the DMA transfer (NPQ bit is cleared) before writing the TxPoll register again. The extra IO traffic added by the proposed workaround could be minimalized but it is not a high-priority task. Fix for: http://bugzilla.kernel.org/show_bug.cgi?id=7924 http://bugzilla.kernel.org/show_bug.cgi?id=8688 (http://bugzilla.kernel.org/show_bug.cgi?id=7555 ?) Signed-off-by: Francois Romieu Cc: David Gundersen Cc: Edward Hsu --- drivers/net/r8169.c | 9 +++++++++ 1 file changed, 9 insertions(+) (limited to 'drivers/net') diff --git a/drivers/net/r8169.c b/drivers/net/r8169.c index d9bb51b..c921ec3 100644 --- a/drivers/net/r8169.c +++ b/drivers/net/r8169.c @@ -2570,6 +2570,15 @@ static void rtl8169_tx_interrupt(struct net_device *dev, (TX_BUFFS_AVAIL(tp) >= MAX_SKB_FRAGS)) { netif_wake_queue(dev); } + /* + * 8168 hack: TxPoll requests are lost when the Tx packets are + * too close. Let's kick an extra TxPoll request when a burst + * of start_xmit activity is detected (if it is not detected, + * it is slow enough). -- FR + */ + smp_rmb(); + if (tp->cur_tx != dirty_tx) + RTL_W8(TxPoll, NPQ); } } -- cgit v1.1 From a07bc1ffaeee9f05490193f66915ac086c6ea5c9 Mon Sep 17 00:00:00 2001 From: Brice Goglin Date: Fri, 14 Sep 2007 00:40:14 +0200 Subject: myri10ge: Add support for PCI device id 9 Add support for new Myri-10G boards with PCI device id 9. Signed-off-by: Brice Goglin Signed-off-by: Jeff Garzik --- drivers/net/myri10ge/myri10ge.c | 3 +++ 1 file changed, 3 insertions(+) (limited to 'drivers/net') diff --git a/drivers/net/myri10ge/myri10ge.c b/drivers/net/myri10ge/myri10ge.c index 1c42266..556962f 100644 --- a/drivers/net/myri10ge/myri10ge.c +++ b/drivers/net/myri10ge/myri10ge.c @@ -3094,9 +3094,12 @@ static void myri10ge_remove(struct pci_dev *pdev) } #define PCI_DEVICE_ID_MYRICOM_MYRI10GE_Z8E 0x0008 +#define PCI_DEVICE_ID_MYRICOM_MYRI10GE_Z8E_9 0x0009 static struct pci_device_id myri10ge_pci_tbl[] = { {PCI_DEVICE(PCI_VENDOR_ID_MYRICOM, PCI_DEVICE_ID_MYRICOM_MYRI10GE_Z8E)}, + {PCI_DEVICE + (PCI_VENDOR_ID_MYRICOM, PCI_DEVICE_ID_MYRICOM_MYRI10GE_Z8E_9)}, {0}, }; -- cgit v1.1 From 680e9fe9d69ea86e81c859932bfd751be91cc0e0 Mon Sep 17 00:00:00 2001 From: Domen Puncer Date: Mon, 17 Sep 2007 22:21:40 +0200 Subject: phy: export phy_mii_ioctl Export phy_mii_ioctl, so network drivers can use it when built as modules too. Signed-off-by: Domen Puncer Signed-off-by: Jeff Garzik --- drivers/net/phy/phy.c | 1 + 1 file changed, 1 insertion(+) (limited to 'drivers/net') diff --git a/drivers/net/phy/phy.c b/drivers/net/phy/phy.c index 0cc4369..cb230f4 100644 --- a/drivers/net/phy/phy.c +++ b/drivers/net/phy/phy.c @@ -409,6 +409,7 @@ int phy_mii_ioctl(struct phy_device *phydev, return 0; } +EXPORT_SYMBOL(phy_mii_ioctl); /** * phy_start_aneg - start auto-negotiation for this PHY device -- cgit v1.1 From 21d0c83302fb742b7ffb6089d40196166102f5ed Mon Sep 17 00:00:00 2001 From: Herbert Xu Date: Wed, 19 Sep 2007 10:45:02 -0700 Subject: [PPP] pppoe: Fix double-free on skb after transmit failure When I got rid of the second packet in __pppoe_xmit I created a double-free on the skb because of the goto abort on failure. This patch removes that. Signed-off-by: Herbert Xu Signed-off-by: David S. Miller --- drivers/net/pppoe.c | 3 +-- 1 file changed, 1 insertion(+), 2 deletions(-) (limited to 'drivers/net') diff --git a/drivers/net/pppoe.c b/drivers/net/pppoe.c index 0d7f570..9b30cd6 100644 --- a/drivers/net/pppoe.c +++ b/drivers/net/pppoe.c @@ -879,8 +879,7 @@ static int __pppoe_xmit(struct sock *sk, struct sk_buff *skb) dev->hard_header(skb, dev, ETH_P_PPP_SES, po->pppoe_pa.remote, NULL, data_len); - if (dev_queue_xmit(skb) < 0) - goto abort; + dev_queue_xmit(skb); return 1; -- cgit v1.1 From a14d6abc947a5504e8d0f934da57b5bc4cea59ca Mon Sep 17 00:00:00 2001 From: Herbert Xu Date: Tue, 18 Sep 2007 13:18:17 -0700 Subject: [PPP] L2TP: Disallow non-UDP datagram sockets With the addition of UDP-Lite we need to refine the socket check so that only genuine UDP sockets are allowed through. Signed-off-by: Herbert Xu Signed-off-by: David S. Miller --- drivers/net/pppol2tp.c | 11 ++++++----- 1 file changed, 6 insertions(+), 5 deletions(-) (limited to 'drivers/net') diff --git a/drivers/net/pppol2tp.c b/drivers/net/pppol2tp.c index 266e8b3..ed8ead4 100644 --- a/drivers/net/pppol2tp.c +++ b/drivers/net/pppol2tp.c @@ -1326,12 +1326,14 @@ static struct sock *pppol2tp_prepare_tunnel_socket(int fd, u16 tunnel_id, goto err; } + sk = sock->sk; + /* Quick sanity checks */ - err = -ESOCKTNOSUPPORT; - if (sock->type != SOCK_DGRAM) { + err = -EPROTONOSUPPORT; + if (sk->sk_protocol != IPPROTO_UDP) { PRINTK(-1, PPPOL2TP_MSG_CONTROL, KERN_ERR, - "tunl %hu: fd %d wrong type, got %d, expected %d\n", - tunnel_id, fd, sock->type, SOCK_DGRAM); + "tunl %hu: fd %d wrong protocol, got %d, expected %d\n", + tunnel_id, fd, sk->sk_protocol, IPPROTO_UDP); goto err; } err = -EAFNOSUPPORT; @@ -1343,7 +1345,6 @@ static struct sock *pppol2tp_prepare_tunnel_socket(int fd, u16 tunnel_id, } err = -ENOTCONN; - sk = sock->sk; /* Check if this socket has already been prepped */ tunnel = (struct pppol2tp_tunnel *)sk->sk_user_data; -- cgit v1.1 From 7a70e39b6633ad85936b029463134ee2599600f1 Mon Sep 17 00:00:00 2001 From: Herbert Xu Date: Tue, 18 Sep 2007 13:18:42 -0700 Subject: [PPP] L2TP: Fix skb handling in pppol2tp_recv_core The function pppol2tp_recv_core doesn't handle non-linear packets properly. It also fails to check the remote offset field. This patch fixes these problems. It also removes an unnecessary check on the UDP header which has already been performed by the UDP layer. Signed-off-by: Herbert Xu Signed-off-by: David S. Miller --- drivers/net/pppol2tp.c | 44 ++++++++++++++++++++++++-------------------- 1 file changed, 24 insertions(+), 20 deletions(-) (limited to 'drivers/net') diff --git a/drivers/net/pppol2tp.c b/drivers/net/pppol2tp.c index ed8ead4..440e190 100644 --- a/drivers/net/pppol2tp.c +++ b/drivers/net/pppol2tp.c @@ -491,44 +491,46 @@ static int pppol2tp_recv_core(struct sock *sock, struct sk_buff *skb) u16 hdrflags; u16 tunnel_id, session_id; int length; - struct udphdr *uh; + int offset; tunnel = pppol2tp_sock_to_tunnel(sock); if (tunnel == NULL) goto error; + /* UDP always verifies the packet length. */ + __skb_pull(skb, sizeof(struct udphdr)); + /* Short packet? */ - if (skb->len < sizeof(struct udphdr)) { + if (!pskb_may_pull(skb, 12)) { PRINTK(tunnel->debug, PPPOL2TP_MSG_DATA, KERN_INFO, "%s: recv short packet (len=%d)\n", tunnel->name, skb->len); goto error; } /* Point to L2TP header */ - ptr = skb->data + sizeof(struct udphdr); + ptr = skb->data; /* Get L2TP header flags */ hdrflags = ntohs(*(__be16*)ptr); /* Trace packet contents, if enabled */ if (tunnel->debug & PPPOL2TP_MSG_DATA) { + length = min(16u, skb->len); + if (!pskb_may_pull(skb, length)) + goto error; + printk(KERN_DEBUG "%s: recv: ", tunnel->name); - for (length = 0; length < 16; length++) - printk(" %02X", ptr[length]); + offset = 0; + do { + printk(" %02X", ptr[offset]); + } while (++offset < length); + printk("\n"); } /* Get length of L2TP packet */ - uh = (struct udphdr *) skb_transport_header(skb); - length = ntohs(uh->len) - sizeof(struct udphdr); - - /* Too short? */ - if (length < 12) { - PRINTK(tunnel->debug, PPPOL2TP_MSG_DATA, KERN_INFO, - "%s: recv short L2TP packet (len=%d)\n", tunnel->name, length); - goto error; - } + length = skb->len; /* If type is control packet, it is handled by userspace. */ if (hdrflags & L2TP_HDRFLAG_T) { @@ -606,7 +608,6 @@ static int pppol2tp_recv_core(struct sock *sock, struct sk_buff *skb) "%s: recv data has no seq numbers when required. " "Discarding\n", session->name); session->stats.rx_seq_discards++; - session->stats.rx_errors++; goto discard; } @@ -625,7 +626,6 @@ static int pppol2tp_recv_core(struct sock *sock, struct sk_buff *skb) "%s: recv data has no seq numbers when required. " "Discarding\n", session->name); session->stats.rx_seq_discards++; - session->stats.rx_errors++; goto discard; } @@ -634,10 +634,14 @@ static int pppol2tp_recv_core(struct sock *sock, struct sk_buff *skb) } /* If offset bit set, skip it. */ - if (hdrflags & L2TP_HDRFLAG_O) - ptr += 2 + ntohs(*(__be16 *) ptr); + if (hdrflags & L2TP_HDRFLAG_O) { + offset = ntohs(*(__be16 *)ptr); + skb->transport_header += 2 + offset; + if (!pskb_may_pull(skb, skb_transport_offset(skb) + 2)) + goto discard; + } - skb_pull(skb, ptr - skb->data); + __skb_pull(skb, skb_transport_offset(skb)); /* Skip PPP header, if present. In testing, Microsoft L2TP clients * don't send the PPP header (PPP header compression enabled), but @@ -673,7 +677,6 @@ static int pppol2tp_recv_core(struct sock *sock, struct sk_buff *skb) */ if (PPPOL2TP_SKB_CB(skb)->ns != session->nr) { session->stats.rx_seq_discards++; - session->stats.rx_errors++; PRINTK(session->debug, PPPOL2TP_MSG_SEQ, KERN_DEBUG, "%s: oos pkt %hu len %d discarded, " "waiting for %hu, reorder_q_len=%d\n", @@ -698,6 +701,7 @@ static int pppol2tp_recv_core(struct sock *sock, struct sk_buff *skb) return 0; discard: + session->stats.rx_errors++; kfree_skb(skb); sock_put(session->sock); -- cgit v1.1 From f3d5e3a4155b6f42f6f6f0a2cc95ca0adbabe1af Mon Sep 17 00:00:00 2001 From: Herbert Xu Date: Wed, 19 Sep 2007 10:46:28 -0700 Subject: [PPP] L2TP: Fix skb handling in pppol2tp_xmit This patch makes pppol2tp_xmit call skb_cow_head so that we don't modify cloned skb data. It also gets rid of skb2 we only need to preserve the original skb for congestion notification, which is only applicable for ppp_async and ppp_sync. The other semantic change made here is the removal of socket accounting for data tranmitted out of pppol2tp_xmit. The original code leaked any existing socket skb accounting. We could fix this by dropping the original skb owner. However, this is undesirable as the packet has not physically left the host yet. In fact, all other tunnels in the kernel do not account skb's passing through to their own socket. In partciular, ESP over UDP does not do so and it is the closest tunnel type to PPPoL2TP. So this patch simply removes the socket accounting in pppol2tp_xmit. The accounting still applies to control packets of course. I've also added a reminder that the outgoing checksum here doesn't work. I suppose existing deployments don't actually enable checksums. Signed-off-by: Herbert Xu Signed-off-by: David S. Miller --- drivers/net/pppol2tp.c | 63 ++++++++++++++++++-------------------------------- 1 file changed, 23 insertions(+), 40 deletions(-) (limited to 'drivers/net') diff --git a/drivers/net/pppol2tp.c b/drivers/net/pppol2tp.c index 440e190..abe91cb 100644 --- a/drivers/net/pppol2tp.c +++ b/drivers/net/pppol2tp.c @@ -962,7 +962,6 @@ static int pppol2tp_xmit(struct ppp_channel *chan, struct sk_buff *skb) int data_len = skb->len; struct inet_sock *inet; __wsum csum = 0; - struct sk_buff *skb2 = NULL; struct udphdr *uh; unsigned int len; @@ -993,41 +992,30 @@ static int pppol2tp_xmit(struct ppp_channel *chan, struct sk_buff *skb) */ headroom = NET_SKB_PAD + sizeof(struct iphdr) + sizeof(struct udphdr) + hdr_len + sizeof(ppph); - if (skb_headroom(skb) < headroom) { - skb2 = skb_realloc_headroom(skb, headroom); - if (skb2 == NULL) - goto abort; - } else - skb2 = skb; - - /* Check that the socket has room */ - if (atomic_read(&sk_tun->sk_wmem_alloc) < sk_tun->sk_sndbuf) - skb_set_owner_w(skb2, sk_tun); - else - goto discard; + if (skb_cow_head(skb, headroom)) + goto abort; /* Setup PPP header */ - skb_push(skb2, sizeof(ppph)); - skb2->data[0] = ppph[0]; - skb2->data[1] = ppph[1]; + __skb_push(skb, sizeof(ppph)); + skb->data[0] = ppph[0]; + skb->data[1] = ppph[1]; /* Setup L2TP header */ - skb_push(skb2, hdr_len); - pppol2tp_build_l2tp_header(session, skb2->data); + pppol2tp_build_l2tp_header(session, __skb_push(skb, hdr_len)); /* Setup UDP header */ inet = inet_sk(sk_tun); - skb_push(skb2, sizeof(struct udphdr)); - skb_reset_transport_header(skb2); - uh = (struct udphdr *) skb2->data; + __skb_push(skb, sizeof(*uh)); + skb_reset_transport_header(skb); + uh = udp_hdr(skb); uh->source = inet->sport; uh->dest = inet->dport; uh->len = htons(sizeof(struct udphdr) + hdr_len + sizeof(ppph) + data_len); uh->check = 0; - /* Calculate UDP checksum if configured to do so */ + /* *BROKEN* Calculate UDP checksum if configured to do so */ if (sk_tun->sk_no_check != UDP_CSUM_NOXMIT) - csum = udp_csum_outgoing(sk_tun, skb2); + csum = udp_csum_outgoing(sk_tun, skb); /* Debug */ if (session->send_seq) @@ -1040,7 +1028,7 @@ static int pppol2tp_xmit(struct ppp_channel *chan, struct sk_buff *skb) if (session->debug & PPPOL2TP_MSG_DATA) { int i; - unsigned char *datap = skb2->data; + unsigned char *datap = skb->data; printk(KERN_DEBUG "%s: xmit:", session->name); for (i = 0; i < data_len; i++) { @@ -1053,18 +1041,18 @@ static int pppol2tp_xmit(struct ppp_channel *chan, struct sk_buff *skb) printk("\n"); } - memset(&(IPCB(skb2)->opt), 0, sizeof(IPCB(skb2)->opt)); - IPCB(skb2)->flags &= ~(IPSKB_XFRM_TUNNEL_SIZE | IPSKB_XFRM_TRANSFORMED | - IPSKB_REROUTED); - nf_reset(skb2); + memset(&(IPCB(skb)->opt), 0, sizeof(IPCB(skb)->opt)); + IPCB(skb)->flags &= ~(IPSKB_XFRM_TUNNEL_SIZE | IPSKB_XFRM_TRANSFORMED | + IPSKB_REROUTED); + nf_reset(skb); /* Get routing info from the tunnel socket */ - dst_release(skb2->dst); - skb2->dst = sk_dst_get(sk_tun); + dst_release(skb->dst); + skb->dst = sk_dst_get(sk_tun); /* Queue the packet to IP for output */ - len = skb2->len; - rc = ip_queue_xmit(skb2, 1); + len = skb->len; + rc = ip_queue_xmit(skb, 1); /* Update stats */ if (rc >= 0) { @@ -1077,17 +1065,12 @@ static int pppol2tp_xmit(struct ppp_channel *chan, struct sk_buff *skb) session->stats.tx_errors++; } - /* Free the original skb */ - kfree_skb(skb); - return 1; -discard: - /* Free the new skb. Caller will free original skb. */ - if (skb2 != skb) - kfree_skb(skb2); abort: - return 0; + /* Free the original skb */ + kfree_skb(skb); + return 1; } /***************************************************************************** -- cgit v1.1 From cd46171c7297739dc7e46d885862e98023eab9c7 Mon Sep 17 00:00:00 2001 From: Michael Chan Date: Thu, 20 Sep 2007 11:04:58 -0700 Subject: [BNX2]: Add PHY workaround for 5709 A1. Add the DIS_EARLY_DAC PHY workaround for 5709 A1. Without it, link sometimes does not come up. Update version to 1.6.5. Signed-off-by: Michael Chan Signed-off-by: David S. Miller --- drivers/net/bnx2.c | 7 ++++--- 1 file changed, 4 insertions(+), 3 deletions(-) (limited to 'drivers/net') diff --git a/drivers/net/bnx2.c b/drivers/net/bnx2.c index 854d80c..66eed22 100644 --- a/drivers/net/bnx2.c +++ b/drivers/net/bnx2.c @@ -54,8 +54,8 @@ #define DRV_MODULE_NAME "bnx2" #define PFX DRV_MODULE_NAME ": " -#define DRV_MODULE_VERSION "1.6.4" -#define DRV_MODULE_RELDATE "August 3, 2007" +#define DRV_MODULE_VERSION "1.6.5" +#define DRV_MODULE_RELDATE "September 20, 2007" #define RUN_AT(x) (jiffies + (x)) @@ -6727,7 +6727,8 @@ bnx2_init_board(struct pci_dev *pdev, struct net_device *dev) } else if (CHIP_NUM(bp) == CHIP_NUM_5706 || CHIP_NUM(bp) == CHIP_NUM_5708) bp->phy_flags |= PHY_CRC_FIX_FLAG; - else if (CHIP_ID(bp) == CHIP_ID_5709_A0) + else if (CHIP_ID(bp) == CHIP_ID_5709_A0 || + CHIP_ID(bp) == CHIP_ID_5709_A1) bp->phy_flags |= PHY_DIS_EARLY_DAC_FLAG; if ((CHIP_ID(bp) == CHIP_ID_5708_A0) || -- cgit v1.1 From d6532232cd3de79c852685823a9c52f723816d0a Mon Sep 17 00:00:00 2001 From: Stephen Hemminger Date: Wed, 19 Sep 2007 15:36:42 -0700 Subject: sky2: fix VLAN receive processing (resend) The length check for truncated frames was not correctly handling the case where VLAN acceleration had already read the tag. Also, the Yukon EX has some features that use high bit of status as security tag. Signed-off-by: Pierre-Yves Ritschard Signed-off-by: Stephen Hemminger Signed-off-by: Jeff Garzik --- drivers/net/sky2.c | 14 +++++++++++++- drivers/net/sky2.h | 2 +- 2 files changed, 14 insertions(+), 2 deletions(-) (limited to 'drivers/net') diff --git a/drivers/net/sky2.c b/drivers/net/sky2.c index 5d812de..8b15654 100644 --- a/drivers/net/sky2.c +++ b/drivers/net/sky2.c @@ -2103,6 +2103,13 @@ static struct sk_buff *sky2_receive(struct net_device *dev, struct sky2_port *sky2 = netdev_priv(dev); struct rx_ring_info *re = sky2->rx_ring + sky2->rx_next; struct sk_buff *skb = NULL; + u16 count = (status & GMR_FS_LEN) >> 16; + +#ifdef SKY2_VLAN_TAG_USED + /* Account for vlan tag */ + if (sky2->vlgrp && (status & GMR_FS_VLAN)) + count -= VLAN_HLEN; +#endif if (unlikely(netif_msg_rx_status(sky2))) printk(KERN_DEBUG PFX "%s: rx slot %u status 0x%x len %d\n", @@ -2117,7 +2124,8 @@ static struct sk_buff *sky2_receive(struct net_device *dev, if (!(status & GMR_FS_RX_OK)) goto resubmit; - if (status >> 16 != length) + /* if length reported by DMA does not match PHY, packet was truncated */ + if (length != count) goto len_mismatch; if (length < copybreak) @@ -2133,6 +2141,10 @@ len_mismatch: /* Truncation of overlength packets causes PHY length to not match MAC length */ ++sky2->net_stats.rx_length_errors; + if (netif_msg_rx_err(sky2) && net_ratelimit()) + pr_info(PFX "%s: rx length mismatch: length %d status %#x\n", + dev->name, length, status); + goto resubmit; error: ++sky2->net_stats.rx_errors; diff --git a/drivers/net/sky2.h b/drivers/net/sky2.h index 72e12b7c..3baae48 100644 --- a/drivers/net/sky2.h +++ b/drivers/net/sky2.h @@ -1668,7 +1668,7 @@ enum { /* Receive Frame Status Encoding */ enum { - GMR_FS_LEN = 0xffff<<16, /* Bit 31..16: Rx Frame Length */ + GMR_FS_LEN = 0x7fff<<16, /* Bit 30..16: Rx Frame Length */ GMR_FS_VLAN = 1<<13, /* VLAN Packet */ GMR_FS_JABBER = 1<<12, /* Jabber Packet */ GMR_FS_UN_SIZE = 1<<11, /* Undersize Packet */ -- cgit v1.1 From c99210b50fe741026d86fdcb5f3f5a0c00c503cc Mon Sep 17 00:00:00 2001 From: Stephen Hemminger Date: Wed, 19 Sep 2007 15:36:43 -0700 Subject: sky2: ethtool speed report bug On 100mbit versions, the driver always reports gigabit speed available. The correct modes are already computed, then overwritten. Signed-off-by: Stephen Hemminger Signed-off-by: Jeff Garzik --- drivers/net/sky2.c | 7 ------- 1 file changed, 7 deletions(-) (limited to 'drivers/net') diff --git a/drivers/net/sky2.c b/drivers/net/sky2.c index 8b15654..94552cc 100644 --- a/drivers/net/sky2.c +++ b/drivers/net/sky2.c @@ -2841,13 +2841,6 @@ static int sky2_get_settings(struct net_device *dev, struct ethtool_cmd *ecmd) ecmd->supported = sky2_supported_modes(hw); ecmd->phy_address = PHY_ADDR_MARV; if (sky2_is_copper(hw)) { - ecmd->supported = SUPPORTED_10baseT_Half - | SUPPORTED_10baseT_Full - | SUPPORTED_100baseT_Half - | SUPPORTED_100baseT_Full - | SUPPORTED_1000baseT_Half - | SUPPORTED_1000baseT_Full - | SUPPORTED_Autoneg | SUPPORTED_TP; ecmd->port = PORT_TP; ecmd->speed = sky2->speed; } else { -- cgit v1.1 From ea76e63598eb312e5d33a782275be91038fc6df2 Mon Sep 17 00:00:00 2001 From: Stephen Hemminger Date: Wed, 19 Sep 2007 15:36:44 -0700 Subject: sky2: reorganize chip revision features This patch should cause no functional changes in driver behaviour. There are (too) many revisions of the Yukon 2 chip now. Instead of adding more conditionals based on chip revision; rerganize into a set of feature flags so adding new versions is less problematic. Signed-off-by: Stephen Hemminger Signed-off-by: Jeff Garzik --- drivers/net/sky2.c | 135 +++++++++++++++++++++++++++++++---------------------- drivers/net/sky2.h | 12 ++++- 2 files changed, 90 insertions(+), 57 deletions(-) (limited to 'drivers/net') diff --git a/drivers/net/sky2.c b/drivers/net/sky2.c index 94552cc..060951a 100644 --- a/drivers/net/sky2.c +++ b/drivers/net/sky2.c @@ -217,8 +217,7 @@ static void sky2_power_on(struct sky2_hw *hw) else sky2_write8(hw, B2_Y2_CLK_GATE, 0); - if (hw->chip_id == CHIP_ID_YUKON_EC_U || - hw->chip_id == CHIP_ID_YUKON_EX) { + if (hw->flags & SKY2_HW_ADV_POWER_CTL) { u32 reg; sky2_pci_write32(hw, PCI_DEV_REG3, 0); @@ -311,10 +310,8 @@ static void sky2_phy_init(struct sky2_hw *hw, unsigned port) struct sky2_port *sky2 = netdev_priv(hw->dev[port]); u16 ctrl, ct1000, adv, pg, ledctrl, ledover, reg; - if (sky2->autoneg == AUTONEG_ENABLE - && !(hw->chip_id == CHIP_ID_YUKON_XL - || hw->chip_id == CHIP_ID_YUKON_EC_U - || hw->chip_id == CHIP_ID_YUKON_EX)) { + if (sky2->autoneg == AUTONEG_ENABLE && + !(hw->flags & SKY2_HW_NEWER_PHY)) { u16 ectrl = gm_phy_read(hw, port, PHY_MARV_EXT_CTRL); ectrl &= ~(PHY_M_EC_M_DSC_MSK | PHY_M_EC_S_DSC_MSK | @@ -346,9 +343,7 @@ static void sky2_phy_init(struct sky2_hw *hw, unsigned port) /* downshift on PHY 88E1112 and 88E1149 is changed */ if (sky2->autoneg == AUTONEG_ENABLE - && (hw->chip_id == CHIP_ID_YUKON_XL - || hw->chip_id == CHIP_ID_YUKON_EC_U - || hw->chip_id == CHIP_ID_YUKON_EX)) { + && (hw->flags & SKY2_HW_NEWER_PHY)) { /* set downshift counter to 3x and enable downshift */ ctrl &= ~PHY_M_PC_DSC_MSK; ctrl |= PHY_M_PC_DSC(2) | PHY_M_PC_DOWN_S_ENA; @@ -364,7 +359,7 @@ static void sky2_phy_init(struct sky2_hw *hw, unsigned port) gm_phy_write(hw, port, PHY_MARV_PHY_CTRL, ctrl); /* special setup for PHY 88E1112 Fiber */ - if (hw->chip_id == CHIP_ID_YUKON_XL && !sky2_is_copper(hw)) { + if (hw->chip_id == CHIP_ID_YUKON_XL && (hw->flags & SKY2_HW_FIBRE_PHY)) { pg = gm_phy_read(hw, port, PHY_MARV_EXT_ADR); /* Fiber: select 1000BASE-X only mode MAC Specific Ctrl Reg. */ @@ -788,7 +783,7 @@ static void sky2_mac_init(struct sky2_hw *hw, unsigned port) sky2_write8(hw, SK_REG(port, TX_GMF_CTRL_T), GMF_RST_CLR); sky2_write16(hw, SK_REG(port, TX_GMF_CTRL_T), GMF_OPER_ON); - if (hw->chip_id == CHIP_ID_YUKON_EC_U || hw->chip_id == CHIP_ID_YUKON_EX) { + if (!(hw->flags & SKY2_HW_RAMBUFFER)) { sky2_write8(hw, SK_REG(port, RX_GMF_LP_THR), 768/8); sky2_write8(hw, SK_REG(port, RX_GMF_UP_THR), 1024/8); @@ -967,19 +962,15 @@ static void sky2_rx_unmap_skb(struct pci_dev *pdev, struct rx_ring_info *re) */ static void rx_set_checksum(struct sky2_port *sky2) { - struct sky2_rx_le *le; - - if (sky2->hw->chip_id != CHIP_ID_YUKON_EX) { - le = sky2_next_rx(sky2); - le->addr = cpu_to_le32((ETH_HLEN << 16) | ETH_HLEN); - le->ctrl = 0; - le->opcode = OP_TCPSTART | HW_OWNER; + struct sky2_rx_le *le = sky2_next_rx(sky2); - sky2_write32(sky2->hw, - Q_ADDR(rxqaddr[sky2->port], Q_CSR), - sky2->rx_csum ? BMU_ENA_RX_CHKSUM : BMU_DIS_RX_CHKSUM); - } + le->addr = cpu_to_le32((ETH_HLEN << 16) | ETH_HLEN); + le->ctrl = 0; + le->opcode = OP_TCPSTART | HW_OWNER; + sky2_write32(sky2->hw, + Q_ADDR(rxqaddr[sky2->port], Q_CSR), + sky2->rx_csum ? BMU_ENA_RX_CHKSUM : BMU_DIS_RX_CHKSUM); } /* @@ -1175,7 +1166,8 @@ static int sky2_rx_start(struct sky2_port *sky2) sky2_prefetch_init(hw, rxq, sky2->rx_le_map, RX_LE_SIZE - 1); - rx_set_checksum(sky2); + if (!(hw->flags & SKY2_HW_NEW_LE)) + rx_set_checksum(sky2); /* Space needed for frame data + headers rounded up */ size = roundup(sky2->netdev->mtu + ETH_HLEN + VLAN_HLEN, 8); @@ -1246,7 +1238,7 @@ static int sky2_up(struct net_device *dev) struct sky2_port *sky2 = netdev_priv(dev); struct sky2_hw *hw = sky2->hw; unsigned port = sky2->port; - u32 ramsize, imask; + u32 imask; int cap, err = -ENOMEM; struct net_device *otherdev = hw->dev[sky2->port^1]; @@ -1301,13 +1293,13 @@ static int sky2_up(struct net_device *dev) sky2_mac_init(hw, port); - /* Register is number of 4K blocks on internal RAM buffer. */ - ramsize = sky2_read8(hw, B2_E_0) * 4; - printk(KERN_INFO PFX "%s: ram buffer %dK\n", dev->name, ramsize); - - if (ramsize > 0) { + if (hw->flags & SKY2_HW_RAMBUFFER) { + /* Register is number of 4K blocks on internal RAM buffer. */ + u32 ramsize = sky2_read8(hw, B2_E_0) * 4; u32 rxspace; + printk(KERN_DEBUG PFX "%s: ram buffer %dK\n", dev->name, ramsize); + if (ramsize < 16) rxspace = ramsize / 2; else @@ -1436,13 +1428,15 @@ static int sky2_xmit_frame(struct sk_buff *skb, struct net_device *dev) /* Check for TCP Segmentation Offload */ mss = skb_shinfo(skb)->gso_size; if (mss != 0) { - if (hw->chip_id != CHIP_ID_YUKON_EX) + + if (!(hw->flags & SKY2_HW_NEW_LE)) mss += ETH_HLEN + ip_hdrlen(skb) + tcp_hdrlen(skb); if (mss != sky2->tx_last_mss) { le = get_tx_le(sky2); le->addr = cpu_to_le32(mss); - if (hw->chip_id == CHIP_ID_YUKON_EX) + + if (hw->flags & SKY2_HW_NEW_LE) le->opcode = OP_MSS | HW_OWNER; else le->opcode = OP_LRGLEN | HW_OWNER; @@ -1468,8 +1462,7 @@ static int sky2_xmit_frame(struct sk_buff *skb, struct net_device *dev) /* Handle TCP checksum offload */ if (skb->ip_summed == CHECKSUM_PARTIAL) { /* On Yukon EX (some versions) encoding change. */ - if (hw->chip_id == CHIP_ID_YUKON_EX - && hw->chip_rev != CHIP_REV_YU_EX_B0) + if (hw->flags & SKY2_HW_AUTO_TX_SUM) ctrl |= CALSUM; /* auto checksum */ else { const unsigned offset = skb_transport_offset(skb); @@ -1708,7 +1701,7 @@ static int sky2_down(struct net_device *dev) static u16 sky2_phy_speed(const struct sky2_hw *hw, u16 aux) { - if (!sky2_is_copper(hw)) + if (hw->flags & SKY2_HW_FIBRE_PHY) return SPEED_1000; if (hw->chip_id == CHIP_ID_YUKON_FE) @@ -1753,9 +1746,7 @@ static void sky2_link_up(struct sky2_port *sky2) sky2_write8(hw, SK_REG(port, LNK_LED_REG), LINKLED_ON | LINKLED_BLINK_OFF | LINKLED_LINKSYNC_OFF); - if (hw->chip_id == CHIP_ID_YUKON_XL - || hw->chip_id == CHIP_ID_YUKON_EC_U - || hw->chip_id == CHIP_ID_YUKON_EX) { + if (hw->flags & SKY2_HW_NEWER_PHY) { u16 pg = gm_phy_read(hw, port, PHY_MARV_EXT_ADR); u16 led = PHY_M_LEDC_LOS_CTRL(1); /* link active */ @@ -1847,7 +1838,7 @@ static int sky2_autoneg_done(struct sky2_port *sky2, u16 aux) /* Since the pause result bits seem to in different positions on * different chips. look at registers. */ - if (!sky2_is_copper(hw)) { + if (hw->flags & SKY2_HW_FIBRE_PHY) { /* Shift for bits in fiber PHY */ advert &= ~(ADVERTISE_PAUSE_CAP|ADVERTISE_PAUSE_ASYM); lpa &= ~(LPA_PAUSE_CAP|LPA_PAUSE_ASYM); @@ -2593,23 +2584,56 @@ static int __devinit sky2_init(struct sky2_hw *hw) sky2_write8(hw, B0_CTST, CS_RST_CLR); hw->chip_id = sky2_read8(hw, B2_CHIP_ID); - if (hw->chip_id < CHIP_ID_YUKON_XL || hw->chip_id > CHIP_ID_YUKON_FE) { + hw->chip_rev = (sky2_read8(hw, B2_MAC_CFG) & CFG_CHIP_R_MSK) >> 4; + + switch(hw->chip_id) { + case CHIP_ID_YUKON_XL: + hw->flags = SKY2_HW_GIGABIT + | SKY2_HW_NEWER_PHY + | SKY2_HW_RAMBUFFER; + break; + + case CHIP_ID_YUKON_EC_U: + hw->flags = SKY2_HW_GIGABIT + | SKY2_HW_NEWER_PHY + | SKY2_HW_ADV_POWER_CTL; + break; + + case CHIP_ID_YUKON_EX: + hw->flags = SKY2_HW_GIGABIT + | SKY2_HW_NEWER_PHY + | SKY2_HW_NEW_LE + | SKY2_HW_ADV_POWER_CTL; + + /* New transmit checksum */ + if (hw->chip_rev != CHIP_REV_YU_EX_B0) + hw->flags |= SKY2_HW_AUTO_TX_SUM; + break; + + case CHIP_ID_YUKON_EC: + /* This rev is really old, and requires untested workarounds */ + if (hw->chip_rev == CHIP_REV_YU_EC_A1) { + dev_err(&hw->pdev->dev, "unsupported revision Yukon-EC rev A1\n"); + return -EOPNOTSUPP; + } + hw->flags = SKY2_HW_GIGABIT | SKY2_HW_RAMBUFFER; + break; + + case CHIP_ID_YUKON_FE: + hw->flags = SKY2_HW_RAMBUFFER; + break; + + default: dev_err(&hw->pdev->dev, "unsupported chip type 0x%x\n", hw->chip_id); return -EOPNOTSUPP; } - hw->chip_rev = (sky2_read8(hw, B2_MAC_CFG) & CFG_CHIP_R_MSK) >> 4; + hw->pmd_type = sky2_read8(hw, B2_PMD_TYP); + if (hw->pmd_type == 'L' || hw->pmd_type == 'S' || hw->pmd_type == 'P') + hw->flags |= SKY2_HW_FIBRE_PHY; - /* This rev is really old, and requires untested workarounds */ - if (hw->chip_id == CHIP_ID_YUKON_EC && hw->chip_rev == CHIP_REV_YU_EC_A1) { - dev_err(&hw->pdev->dev, "unsupported revision Yukon-%s (0x%x) rev %d\n", - yukon2_name[hw->chip_id - CHIP_ID_YUKON_XL], - hw->chip_id, hw->chip_rev); - return -EOPNOTSUPP; - } - hw->pmd_type = sky2_read8(hw, B2_PMD_TYP); hw->ports = 1; t8 = sky2_read8(hw, B2_Y2_HW_RES); if ((t8 & CFG_DUAL_MAC_MSK) == CFG_DUAL_MAC_MSK) { @@ -2821,7 +2845,7 @@ static u32 sky2_supported_modes(const struct sky2_hw *hw) | SUPPORTED_100baseT_Full | SUPPORTED_Autoneg | SUPPORTED_TP; - if (hw->chip_id != CHIP_ID_YUKON_FE) + if (hw->flags & SKY2_HW_GIGABIT) modes |= SUPPORTED_1000baseT_Half | SUPPORTED_1000baseT_Full; return modes; @@ -3851,7 +3875,7 @@ static irqreturn_t __devinit sky2_test_intr(int irq, void *dev_id) return IRQ_NONE; if (status & Y2_IS_IRQ_SW) { - hw->msi = 1; + hw->flags |= SKY2_HW_USE_MSI; wake_up(&hw->msi_wait); sky2_write8(hw, B0_CTST, CS_CL_SW_IRQ); } @@ -3879,9 +3903,9 @@ static int __devinit sky2_test_msi(struct sky2_hw *hw) sky2_write8(hw, B0_CTST, CS_ST_SW_IRQ); sky2_read8(hw, B0_CTST); - wait_event_timeout(hw->msi_wait, hw->msi, HZ/10); + wait_event_timeout(hw->msi_wait, (hw->flags & SKY2_HW_USE_MSI), HZ/10); - if (!hw->msi) { + if (!(hw->flags & SKY2_HW_USE_MSI)) { /* MSI test failed, go back to INTx mode */ dev_info(&pdev->dev, "No interrupt generated using MSI, " "switching to INTx mode.\n"); @@ -4014,7 +4038,8 @@ static int __devinit sky2_probe(struct pci_dev *pdev, goto err_out_free_netdev; } - err = request_irq(pdev->irq, sky2_intr, hw->msi ? 0 : IRQF_SHARED, + err = request_irq(pdev->irq, sky2_intr, + (hw->flags & SKY2_HW_USE_MSI) ? 0 : IRQF_SHARED, dev->name, hw); if (err) { dev_err(&pdev->dev, "cannot assign irq %d\n", pdev->irq); @@ -4047,7 +4072,7 @@ static int __devinit sky2_probe(struct pci_dev *pdev, return 0; err_out_unregister: - if (hw->msi) + if (hw->flags & SKY2_HW_USE_MSI) pci_disable_msi(pdev); unregister_netdev(dev); err_out_free_netdev: @@ -4096,7 +4121,7 @@ static void __devexit sky2_remove(struct pci_dev *pdev) sky2_read8(hw, B0_CTST); free_irq(pdev->irq, hw); - if (hw->msi) + if (hw->flags & SKY2_HW_USE_MSI) pci_disable_msi(pdev); pci_free_consistent(pdev, STATUS_LE_BYTES, hw->st_le, hw->st_dma); pci_release_regions(pdev); diff --git a/drivers/net/sky2.h b/drivers/net/sky2.h index 3baae48..af30349 100644 --- a/drivers/net/sky2.h +++ b/drivers/net/sky2.h @@ -2040,6 +2040,15 @@ struct sky2_hw { void __iomem *regs; struct pci_dev *pdev; struct net_device *dev[2]; + unsigned long flags; +#define SKY2_HW_USE_MSI 0x00000001 +#define SKY2_HW_FIBRE_PHY 0x00000002 +#define SKY2_HW_GIGABIT 0x00000004 +#define SKY2_HW_NEWER_PHY 0x00000008 +#define SKY2_HW_RAMBUFFER 0x00000010 /* chip has RAM FIFO */ +#define SKY2_HW_NEW_LE 0x00000020 /* new LSOv2 format */ +#define SKY2_HW_AUTO_TX_SUM 0x00000040 /* new IP decode for Tx */ +#define SKY2_HW_ADV_POWER_CTL 0x00000080 /* additional PHY power regs */ u8 chip_id; u8 chip_rev; @@ -2053,13 +2062,12 @@ struct sky2_hw { struct timer_list watchdog_timer; struct work_struct restart_work; - int msi; wait_queue_head_t msi_wait; }; static inline int sky2_is_copper(const struct sky2_hw *hw) { - return !(hw->pmd_type == 'L' || hw->pmd_type == 'S' || hw->pmd_type == 'P'); + return !(hw->flags & SKY2_HW_FIBRE_PHY); } /* Register accessor for memory mapped device */ -- cgit v1.1 From 05745c4ab1c58fbb6ab8e8d3a40e0e395d7e2b0e Mon Sep 17 00:00:00 2001 From: Stephen Hemminger Date: Wed, 19 Sep 2007 15:36:45 -0700 Subject: sky2: fe+ chip support Add support for newest Marvell chips. The Yukon FE plus chip is found in some not yet released laptops. Tested on hardware evaluation boards. This version of the patch is for 2.6.23. It supersedes the two previous patches that are sitting in netdev-2.6 (upstream branch). Signed-off-by: Stephen Hemminger Signed-off-by: Jeff Garzik --- drivers/net/sky2.c | 136 ++++++++++++++++++++++++++++++++++++++++------------- drivers/net/sky2.h | 18 +++++-- 2 files changed, 117 insertions(+), 37 deletions(-) (limited to 'drivers/net') diff --git a/drivers/net/sky2.c b/drivers/net/sky2.c index 060951a..d0e5875 100644 --- a/drivers/net/sky2.c +++ b/drivers/net/sky2.c @@ -118,12 +118,15 @@ static const struct pci_device_id sky2_id_table[] = { { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4351) }, /* 88E8036 */ { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4352) }, /* 88E8038 */ { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4353) }, /* 88E8039 */ + { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4354) }, /* 88E8040 */ { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4356) }, /* 88EC033 */ + { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x435A) }, /* 88E8048 */ { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4360) }, /* 88E8052 */ { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4361) }, /* 88E8050 */ { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4362) }, /* 88E8053 */ { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4363) }, /* 88E8055 */ { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4364) }, /* 88E8056 */ + { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4365) }, /* 88E8070 */ { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4366) }, /* 88EC036 */ { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4367) }, /* 88EC032 */ { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4368) }, /* 88EC034 */ @@ -147,6 +150,7 @@ static const char *yukon2_name[] = { "Extreme", /* 0xb5 */ "EC", /* 0xb6 */ "FE", /* 0xb7 */ + "FE+", /* 0xb8 */ }; static void sky2_set_multicast(struct net_device *dev); @@ -331,7 +335,7 @@ static void sky2_phy_init(struct sky2_hw *hw, unsigned port) ctrl = gm_phy_read(hw, port, PHY_MARV_PHY_CTRL); if (sky2_is_copper(hw)) { - if (hw->chip_id == CHIP_ID_YUKON_FE) { + if (!(hw->flags & SKY2_HW_GIGABIT)) { /* enable automatic crossover */ ctrl |= PHY_M_PC_MDI_XMODE(PHY_M_PC_ENA_AUTO) >> 1; } else { @@ -450,7 +454,7 @@ static void sky2_phy_init(struct sky2_hw *hw, unsigned port) gma_write16(hw, port, GM_GP_CTRL, reg); - if (hw->chip_id != CHIP_ID_YUKON_FE) + if (hw->flags & SKY2_HW_GIGABIT) gm_phy_write(hw, port, PHY_MARV_1000T_CTRL, ct1000); gm_phy_write(hw, port, PHY_MARV_AUNE_ADV, adv); @@ -474,6 +478,23 @@ static void sky2_phy_init(struct sky2_hw *hw, unsigned port) gm_phy_write(hw, port, PHY_MARV_FE_LED_PAR, ctrl); break; + case CHIP_ID_YUKON_FE_P: + /* Enable Link Partner Next Page */ + ctrl = gm_phy_read(hw, port, PHY_MARV_PHY_CTRL); + ctrl |= PHY_M_PC_ENA_LIP_NP; + + /* disable Energy Detect and enable scrambler */ + ctrl &= ~(PHY_M_PC_ENA_ENE_DT | PHY_M_PC_DIS_SCRAMB); + gm_phy_write(hw, port, PHY_MARV_PHY_CTRL, ctrl); + + /* set LED2 -> ACT, LED1 -> LINK, LED0 -> SPEED */ + ctrl = PHY_M_FELP_LED2_CTRL(LED_PAR_CTRL_ACT_BL) | + PHY_M_FELP_LED1_CTRL(LED_PAR_CTRL_LINK) | + PHY_M_FELP_LED0_CTRL(LED_PAR_CTRL_SPEED); + + gm_phy_write(hw, port, PHY_MARV_FE_LED_PAR, ctrl); + break; + case CHIP_ID_YUKON_XL: pg = gm_phy_read(hw, port, PHY_MARV_EXT_ADR); @@ -543,7 +564,13 @@ static void sky2_phy_init(struct sky2_hw *hw, unsigned port) /* set page register to 0 */ gm_phy_write(hw, port, PHY_MARV_EXT_ADR, 0); + } else if (hw->chip_id == CHIP_ID_YUKON_FE_P && + hw->chip_rev == CHIP_REV_YU_FE2_A0) { + /* apply workaround for integrated resistors calibration */ + gm_phy_write(hw, port, PHY_MARV_PAGE_ADDR, 17); + gm_phy_write(hw, port, PHY_MARV_PAGE_DATA, 0x3f60); } else if (hw->chip_id != CHIP_ID_YUKON_EX) { + /* no effect on Yukon-XL */ gm_phy_write(hw, port, PHY_MARV_LED_CTRL, ledctrl); if (sky2->autoneg == AUTONEG_DISABLE || sky2->speed == SPEED_100) { @@ -664,25 +691,25 @@ static void sky2_wol_init(struct sky2_port *sky2) static void sky2_set_tx_stfwd(struct sky2_hw *hw, unsigned port) { - if (hw->chip_id == CHIP_ID_YUKON_EX && hw->chip_rev != CHIP_REV_YU_EX_A0) { + struct net_device *dev = hw->dev[port]; + + if (dev->mtu <= ETH_DATA_LEN) sky2_write32(hw, SK_REG(port, TX_GMF_CTRL_T), - TX_STFW_ENA | - (hw->dev[port]->mtu > ETH_DATA_LEN) ? TX_JUMBO_ENA : TX_JUMBO_DIS); - } else { - if (hw->dev[port]->mtu > ETH_DATA_LEN) { - /* set Tx GMAC FIFO Almost Empty Threshold */ - sky2_write32(hw, SK_REG(port, TX_GMF_AE_THR), - (ECU_JUMBO_WM << 16) | ECU_AE_THR); + TX_JUMBO_DIS | TX_STFW_ENA); + + else if (hw->chip_id != CHIP_ID_YUKON_EC_U) + sky2_write32(hw, SK_REG(port, TX_GMF_CTRL_T), + TX_STFW_ENA | TX_JUMBO_ENA); + else { + /* set Tx GMAC FIFO Almost Empty Threshold */ + sky2_write32(hw, SK_REG(port, TX_GMF_AE_THR), + (ECU_JUMBO_WM << 16) | ECU_AE_THR); - sky2_write32(hw, SK_REG(port, TX_GMF_CTRL_T), - TX_JUMBO_ENA | TX_STFW_DIS); + sky2_write32(hw, SK_REG(port, TX_GMF_CTRL_T), + TX_JUMBO_ENA | TX_STFW_DIS); - /* Can't do offload because of lack of store/forward */ - hw->dev[port]->features &= ~(NETIF_F_TSO | NETIF_F_SG - | NETIF_F_ALL_CSUM); - } else - sky2_write32(hw, SK_REG(port, TX_GMF_CTRL_T), - TX_JUMBO_DIS | TX_STFW_ENA); + /* Can't do offload because of lack of store/forward */ + dev->features &= ~(NETIF_F_TSO | NETIF_F_SG | NETIF_F_ALL_CSUM); } } @@ -768,7 +795,8 @@ static void sky2_mac_init(struct sky2_hw *hw, unsigned port) /* Configure Rx MAC FIFO */ sky2_write8(hw, SK_REG(port, RX_GMF_CTRL_T), GMF_RST_CLR); rx_reg = GMF_OPER_ON | GMF_RX_F_FL_ON; - if (hw->chip_id == CHIP_ID_YUKON_EX) + if (hw->chip_id == CHIP_ID_YUKON_EX || + hw->chip_id == CHIP_ID_YUKON_FE_P) rx_reg |= GMF_RX_OVER_ON; sky2_write32(hw, SK_REG(port, RX_GMF_CTRL_T), rx_reg); @@ -777,7 +805,12 @@ static void sky2_mac_init(struct sky2_hw *hw, unsigned port) sky2_write16(hw, SK_REG(port, RX_GMF_FL_MSK), GMR_FS_ANY_ERR); /* Set threshold to 0xa (64 bytes) + 1 to workaround pause bug */ - sky2_write16(hw, SK_REG(port, RX_GMF_FL_THR), RX_GMF_FL_THR_DEF+1); + reg = RX_GMF_FL_THR_DEF + 1; + /* Another magic mystery workaround from sk98lin */ + if (hw->chip_id == CHIP_ID_YUKON_FE_P && + hw->chip_rev == CHIP_REV_YU_FE2_A0) + reg = 0x178; + sky2_write16(hw, SK_REG(port, RX_GMF_FL_THR), reg); /* Configure Tx MAC FIFO */ sky2_write8(hw, SK_REG(port, TX_GMF_CTRL_T), GMF_RST_CLR); @@ -1704,8 +1737,12 @@ static u16 sky2_phy_speed(const struct sky2_hw *hw, u16 aux) if (hw->flags & SKY2_HW_FIBRE_PHY) return SPEED_1000; - if (hw->chip_id == CHIP_ID_YUKON_FE) - return (aux & PHY_M_PS_SPEED_100) ? SPEED_100 : SPEED_10; + if (!(hw->flags & SKY2_HW_GIGABIT)) { + if (aux & PHY_M_PS_SPEED_100) + return SPEED_100; + else + return SPEED_10; + } switch (aux & PHY_M_PS_SPEED_MSK) { case PHY_M_PS_SPEED_1000: @@ -1949,7 +1986,9 @@ static int sky2_change_mtu(struct net_device *dev, int new_mtu) if (new_mtu < ETH_ZLEN || new_mtu > ETH_JUMBO_MTU) return -EINVAL; - if (new_mtu > ETH_DATA_LEN && hw->chip_id == CHIP_ID_YUKON_FE) + if (new_mtu > ETH_DATA_LEN && + (hw->chip_id == CHIP_ID_YUKON_FE || + hw->chip_id == CHIP_ID_YUKON_FE_P)) return -EINVAL; if (!netif_running(dev)) { @@ -1966,7 +2005,7 @@ static int sky2_change_mtu(struct net_device *dev, int new_mtu) synchronize_irq(hw->pdev->irq); - if (hw->chip_id == CHIP_ID_YUKON_EC_U || hw->chip_id == CHIP_ID_YUKON_EX) + if (!(hw->flags & SKY2_HW_RAMBUFFER)) sky2_set_tx_stfwd(hw, port); ctl = gma_read16(hw, port, GM_GP_CTRL); @@ -2205,7 +2244,7 @@ static int sky2_status_intr(struct sky2_hw *hw, int to_do) } /* This chip reports checksum status differently */ - if (hw->chip_id == CHIP_ID_YUKON_EX) { + if (hw->flags & SKY2_HW_NEW_LE) { if (sky2->rx_csum && (le->css & (CSS_ISIPV4 | CSS_ISIPV6)) && (le->css & CSS_TCPUDPCSOK)) @@ -2246,8 +2285,14 @@ static int sky2_status_intr(struct sky2_hw *hw, int to_do) if (!sky2->rx_csum) break; - if (hw->chip_id == CHIP_ID_YUKON_EX) + /* If this happens then driver assuming wrong format */ + if (unlikely(hw->flags & SKY2_HW_NEW_LE)) { + if (net_ratelimit()) + printk(KERN_NOTICE "%s: unexpected" + " checksum status\n", + dev->name); break; + } /* Both checksum counters are programmed to start at * the same offset, so unless there is a problem they @@ -2549,17 +2594,25 @@ static void sky2_netpoll(struct net_device *dev) #endif /* Chip internal frequency for clock calculations */ -static inline u32 sky2_mhz(const struct sky2_hw *hw) +static u32 sky2_mhz(const struct sky2_hw *hw) { switch (hw->chip_id) { case CHIP_ID_YUKON_EC: case CHIP_ID_YUKON_EC_U: case CHIP_ID_YUKON_EX: - return 125; /* 125 Mhz */ + return 125; + case CHIP_ID_YUKON_FE: - return 100; /* 100 Mhz */ - default: /* YUKON_XL */ - return 156; /* 156 Mhz */ + return 100; + + case CHIP_ID_YUKON_FE_P: + return 50; + + case CHIP_ID_YUKON_XL: + return 156; + + default: + BUG(); } } @@ -2623,6 +2676,12 @@ static int __devinit sky2_init(struct sky2_hw *hw) hw->flags = SKY2_HW_RAMBUFFER; break; + case CHIP_ID_YUKON_FE_P: + hw->flags = SKY2_HW_NEWER_PHY + | SKY2_HW_NEW_LE + | SKY2_HW_AUTO_TX_SUM + | SKY2_HW_ADV_POWER_CTL; + break; default: dev_err(&hw->pdev->dev, "unsupported chip type 0x%x\n", hw->chip_id); @@ -2827,7 +2886,9 @@ static int sky2_set_wol(struct net_device *dev, struct ethtool_wolinfo *wol) sky2->wol = wol->wolopts; - if (hw->chip_id == CHIP_ID_YUKON_EC_U || hw->chip_id == CHIP_ID_YUKON_EX) + if (hw->chip_id == CHIP_ID_YUKON_EC_U || + hw->chip_id == CHIP_ID_YUKON_EX || + hw->chip_id == CHIP_ID_YUKON_FE_P) sky2_write32(hw, B0_CTST, sky2->wol ? Y2_HW_WOL_ON : Y2_HW_WOL_OFF); @@ -3820,6 +3881,13 @@ static __devinit struct net_device *sky2_init_netdev(struct sky2_hw *hw, sky2->hw = hw; sky2->msg_enable = netif_msg_init(debug, default_msg); + /* This chip has hardware problems that generates + * bogus PHY receive status so by default shut up the message. + */ + if (hw->chip_id == CHIP_ID_YUKON_FE_P && + hw->chip_rev == CHIP_REV_YU_FE2_A0) + sky2->msg_enable &= ~NETIF_MSG_RX_ERR; + /* Auto speed and flow control */ sky2->autoneg = AUTONEG_ENABLE; sky2->flow_mode = FC_BOTH; @@ -4189,7 +4257,9 @@ static int sky2_resume(struct pci_dev *pdev) pci_enable_wake(pdev, PCI_D0, 0); /* Re-enable all clocks */ - if (hw->chip_id == CHIP_ID_YUKON_EX || hw->chip_id == CHIP_ID_YUKON_EC_U) + if (hw->chip_id == CHIP_ID_YUKON_EX || + hw->chip_id == CHIP_ID_YUKON_EC_U || + hw->chip_id == CHIP_ID_YUKON_FE_P) sky2_pci_write32(hw, PCI_DEV_REG3, 0); sky2_reset(hw); diff --git a/drivers/net/sky2.h b/drivers/net/sky2.h index af30349..a05b30b 100644 --- a/drivers/net/sky2.h +++ b/drivers/net/sky2.h @@ -470,18 +470,24 @@ enum { CHIP_ID_YUKON_EX = 0xb5, /* Chip ID for YUKON-2 Extreme */ CHIP_ID_YUKON_EC = 0xb6, /* Chip ID for YUKON-2 EC */ CHIP_ID_YUKON_FE = 0xb7, /* Chip ID for YUKON-2 FE */ - + CHIP_ID_YUKON_FE_P = 0xb8, /* Chip ID for YUKON-2 FE+ */ +}; +enum yukon_ec_rev { CHIP_REV_YU_EC_A1 = 0, /* Chip Rev. for Yukon-EC A1/A0 */ CHIP_REV_YU_EC_A2 = 1, /* Chip Rev. for Yukon-EC A2 */ CHIP_REV_YU_EC_A3 = 2, /* Chip Rev. for Yukon-EC A3 */ - +}; +enum yukon_ec_u_rev { CHIP_REV_YU_EC_U_A0 = 1, CHIP_REV_YU_EC_U_A1 = 2, CHIP_REV_YU_EC_U_B0 = 3, - +}; +enum yukon_fe_rev { CHIP_REV_YU_FE_A1 = 1, CHIP_REV_YU_FE_A2 = 2, - +}; +enum yukon_fe_p_rev { + CHIP_REV_YU_FE2_A0 = 0, }; enum yukon_ex_rev { CHIP_REV_YU_EX_A0 = 1, @@ -1729,6 +1735,10 @@ enum { GMF_RX_CTRL_DEF = GMF_OPER_ON | GMF_RX_F_FL_ON, }; +/* TX_GMF_EA 32 bit Tx GMAC FIFO End Address */ +enum { + TX_DYN_WM_ENA = 3, /* Yukon-FE+ specific */ +}; /* TX_GMF_CTRL_T 32 bit Tx GMAC FIFO Control/Test */ enum { -- cgit v1.1 From 75e806838a3327d4ca9030e588d34de11b04f341 Mon Sep 17 00:00:00 2001 From: Stephen Hemminger Date: Wed, 19 Sep 2007 15:36:46 -0700 Subject: sky2: receive FIFO checking A driver writer from another operating system hinted that the versions of Yukon 2 chip with rambuffer (EC and XL) have a hardware bug that if the FIFO ever gets completely full it will hang. Sounds like a classic ring full vs ring empty wrap around bug. As a workaround, use the existing watchdog timer to check for ring full lockup. Signed-off-by: Stephen Hemminger Signed-off-by: Jeff Garzik --- drivers/net/sky2.c | 74 ++++++++++++++++++++++++++++++++++++++++++------------ drivers/net/sky2.h | 9 ++++++- 2 files changed, 66 insertions(+), 17 deletions(-) (limited to 'drivers/net') diff --git a/drivers/net/sky2.c b/drivers/net/sky2.c index d0e5875..2831f44 100644 --- a/drivers/net/sky2.c +++ b/drivers/net/sky2.c @@ -1648,9 +1648,6 @@ static int sky2_down(struct net_device *dev) if (netif_msg_ifdown(sky2)) printk(KERN_INFO PFX "%s: disabling interface\n", dev->name); - if (netif_carrier_ok(dev) && --hw->active == 0) - del_timer(&hw->watchdog_timer); - /* Stop more packets from being queued */ netif_stop_queue(dev); @@ -1775,9 +1772,7 @@ static void sky2_link_up(struct sky2_port *sky2) netif_carrier_on(sky2->netdev); - if (hw->active++ == 0) - mod_timer(&hw->watchdog_timer, jiffies + 1); - + mod_timer(&hw->watchdog_timer, jiffies + 1); /* Turn on link LED */ sky2_write8(hw, SK_REG(port, LNK_LED_REG), @@ -1828,11 +1823,6 @@ static void sky2_link_down(struct sky2_port *sky2) netif_carrier_off(sky2->netdev); - /* Stop watchdog if both ports are not active */ - if (--hw->active == 0) - del_timer(&hw->watchdog_timer); - - /* Turn on link LED */ sky2_write8(hw, SK_REG(port, LNK_LED_REG), LINKLED_OFF); @@ -2484,20 +2474,72 @@ static void sky2_le_error(struct sky2_hw *hw, unsigned port, sky2_write32(hw, Q_ADDR(q, Q_CSR), BMU_CLR_IRQ_CHK); } -/* Check for lost IRQ once a second */ +static int sky2_rx_hung(struct net_device *dev) +{ + struct sky2_port *sky2 = netdev_priv(dev); + struct sky2_hw *hw = sky2->hw; + unsigned port = sky2->port; + unsigned rxq = rxqaddr[port]; + u32 mac_rp = sky2_read32(hw, SK_REG(port, RX_GMF_RP)); + u8 mac_lev = sky2_read8(hw, SK_REG(port, RX_GMF_RLEV)); + u8 fifo_rp = sky2_read8(hw, Q_ADDR(rxq, Q_RP)); + u8 fifo_lev = sky2_read8(hw, Q_ADDR(rxq, Q_RL)); + + /* If idle and MAC or PCI is stuck */ + if (sky2->check.last == dev->last_rx && + ((mac_rp == sky2->check.mac_rp && + mac_lev != 0 && mac_lev >= sky2->check.mac_lev) || + /* Check if the PCI RX hang */ + (fifo_rp == sky2->check.fifo_rp && + fifo_lev != 0 && fifo_lev >= sky2->check.fifo_lev))) { + printk(KERN_DEBUG PFX "%s: hung mac %d:%d fifo %d (%d:%d)\n", + dev->name, mac_lev, mac_rp, fifo_lev, fifo_rp, + sky2_read8(hw, Q_ADDR(rxq, Q_WP))); + return 1; + } else { + sky2->check.last = dev->last_rx; + sky2->check.mac_rp = mac_rp; + sky2->check.mac_lev = mac_lev; + sky2->check.fifo_rp = fifo_rp; + sky2->check.fifo_lev = fifo_lev; + return 0; + } +} + static void sky2_watchdog(unsigned long arg) { struct sky2_hw *hw = (struct sky2_hw *) arg; + struct net_device *dev; + /* Check for lost IRQ once a second */ if (sky2_read32(hw, B0_ISRC)) { - struct net_device *dev = hw->dev[0]; - + dev = hw->dev[0]; if (__netif_rx_schedule_prep(dev)) __netif_rx_schedule(dev); + } else { + int i, active = 0; + + for (i = 0; i < hw->ports; i++) { + dev = hw->dev[i]; + if (!netif_running(dev)) + continue; + ++active; + + /* For chips with Rx FIFO, check if stuck */ + if ((hw->flags & SKY2_HW_RAMBUFFER) && + sky2_rx_hung(dev)) { + pr_info(PFX "%s: receiver hang detected\n", + dev->name); + schedule_work(&hw->restart_work); + return; + } + } + + if (active == 0) + return; } - if (hw->active > 0) - mod_timer(&hw->watchdog_timer, round_jiffies(jiffies + HZ)); + mod_timer(&hw->watchdog_timer, round_jiffies(jiffies + HZ)); } /* Hardware/software error handling */ diff --git a/drivers/net/sky2.h b/drivers/net/sky2.h index a05b30b..69cd984 100644 --- a/drivers/net/sky2.h +++ b/drivers/net/sky2.h @@ -2027,6 +2027,14 @@ struct sky2_port { u16 rx_tag; struct vlan_group *vlgrp; #endif + struct { + unsigned long last; + u32 mac_rp; + u8 mac_lev; + u8 fifo_rp; + u8 fifo_lev; + } check; + dma_addr_t rx_le_map; dma_addr_t tx_le_map; @@ -2064,7 +2072,6 @@ struct sky2_hw { u8 chip_rev; u8 pmd_type; u8 ports; - u8 active; struct sky2_status_le *st_le; u32 st_idx; -- cgit v1.1 From faf60e72d07d163a623e47269680918fccaa789a Mon Sep 17 00:00:00 2001 From: Stephen Hemminger Date: Wed, 19 Sep 2007 15:36:47 -0700 Subject: sky2: version 1.18 Update version number Signed-off-by: Stephen Hemminger Signed-off-by: Jeff Garzik --- drivers/net/sky2.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers/net') diff --git a/drivers/net/sky2.c b/drivers/net/sky2.c index 2831f44..eaffe55 100644 --- a/drivers/net/sky2.c +++ b/drivers/net/sky2.c @@ -51,7 +51,7 @@ #include "sky2.h" #define DRV_NAME "sky2" -#define DRV_VERSION "1.17" +#define DRV_VERSION "1.18" #define PFX DRV_NAME " " /* -- cgit v1.1 From 6d3105d5388c359882068b161b431ab3db4b3721 Mon Sep 17 00:00:00 2001 From: Stephen Hemminger Date: Mon, 24 Sep 2007 19:34:51 -0700 Subject: sky2: FE+ Phy initialization One more snippet of PHY initialization required for FE+ chips. Discovered in latest sk98lin 10.21.1.3 driver. Please apply to 2.6.23. Signed-off-by: Stephen Hemminger Signed-off-by: Jeff Garzik --- drivers/net/sky2.c | 10 ++++++++++ 1 file changed, 10 insertions(+) (limited to 'drivers/net') diff --git a/drivers/net/sky2.c b/drivers/net/sky2.c index eaffe55..f3a8243 100644 --- a/drivers/net/sky2.c +++ b/drivers/net/sky2.c @@ -338,6 +338,16 @@ static void sky2_phy_init(struct sky2_hw *hw, unsigned port) if (!(hw->flags & SKY2_HW_GIGABIT)) { /* enable automatic crossover */ ctrl |= PHY_M_PC_MDI_XMODE(PHY_M_PC_ENA_AUTO) >> 1; + + if (hw->chip_id == CHIP_ID_YUKON_FE_P && + hw->chip_rev == CHIP_REV_YU_FE2_A0) { + u16 spec; + + /* Enable Class A driver for FE+ A0 */ + spec = gm_phy_read(hw, port, PHY_MARV_FE_SPEC_2); + spec |= PHY_M_FESC_SEL_CL_A; + gm_phy_write(hw, port, PHY_MARV_FE_SPEC_2, spec); + } } else { /* disable energy detect */ ctrl &= ~PHY_M_PC_EN_DET_MSK; -- cgit v1.1 From e0c281163d634e2982a81b55fc974a6663afde65 Mon Sep 17 00:00:00 2001 From: Stephen Hemminger Date: Thu, 20 Sep 2007 13:03:49 -0700 Subject: sky2: be more selective about FIFO watchdog Be more selective about when to enable the ram buffer watchdog code. It is unnecessary on XL A3 or later revs, and with Yukon FE the buffer is so small (4K) that the watchdog detects false positives. Signed-off-by: Stephen Hemminger Signed-off-by: Jeff Garzik --- drivers/net/sky2.c | 27 ++++++++++++++------------- drivers/net/sky2.h | 2 +- 2 files changed, 15 insertions(+), 14 deletions(-) (limited to 'drivers/net') diff --git a/drivers/net/sky2.c b/drivers/net/sky2.c index f3a8243..0792031 100644 --- a/drivers/net/sky2.c +++ b/drivers/net/sky2.c @@ -826,7 +826,8 @@ static void sky2_mac_init(struct sky2_hw *hw, unsigned port) sky2_write8(hw, SK_REG(port, TX_GMF_CTRL_T), GMF_RST_CLR); sky2_write16(hw, SK_REG(port, TX_GMF_CTRL_T), GMF_OPER_ON); - if (!(hw->flags & SKY2_HW_RAMBUFFER)) { + /* On chips without ram buffer, pause is controled by MAC level */ + if (sky2_read8(hw, B2_E_0) == 0) { sky2_write8(hw, SK_REG(port, RX_GMF_LP_THR), 768/8); sky2_write8(hw, SK_REG(port, RX_GMF_UP_THR), 1024/8); @@ -1281,7 +1282,7 @@ static int sky2_up(struct net_device *dev) struct sky2_port *sky2 = netdev_priv(dev); struct sky2_hw *hw = sky2->hw; unsigned port = sky2->port; - u32 imask; + u32 imask, ramsize; int cap, err = -ENOMEM; struct net_device *otherdev = hw->dev[sky2->port^1]; @@ -1336,13 +1337,12 @@ static int sky2_up(struct net_device *dev) sky2_mac_init(hw, port); - if (hw->flags & SKY2_HW_RAMBUFFER) { - /* Register is number of 4K blocks on internal RAM buffer. */ - u32 ramsize = sky2_read8(hw, B2_E_0) * 4; + /* Register is number of 4K blocks on internal RAM buffer. */ + ramsize = sky2_read8(hw, B2_E_0) * 4; + if (ramsize > 0) { u32 rxspace; - printk(KERN_DEBUG PFX "%s: ram buffer %dK\n", dev->name, ramsize); - + pr_debug(PFX "%s: ram buffer %dK\n", dev->name, ramsize); if (ramsize < 16) rxspace = ramsize / 2; else @@ -2005,7 +2005,7 @@ static int sky2_change_mtu(struct net_device *dev, int new_mtu) synchronize_irq(hw->pdev->irq); - if (!(hw->flags & SKY2_HW_RAMBUFFER)) + if (sky2_read8(hw, B2_E_0) == 0) sky2_set_tx_stfwd(hw, port); ctl = gma_read16(hw, port, GM_GP_CTRL); @@ -2536,7 +2536,7 @@ static void sky2_watchdog(unsigned long arg) ++active; /* For chips with Rx FIFO, check if stuck */ - if ((hw->flags & SKY2_HW_RAMBUFFER) && + if ((hw->flags & SKY2_HW_FIFO_HANG_CHECK) && sky2_rx_hung(dev)) { pr_info(PFX "%s: receiver hang detected\n", dev->name); @@ -2694,8 +2694,10 @@ static int __devinit sky2_init(struct sky2_hw *hw) switch(hw->chip_id) { case CHIP_ID_YUKON_XL: hw->flags = SKY2_HW_GIGABIT - | SKY2_HW_NEWER_PHY - | SKY2_HW_RAMBUFFER; + | SKY2_HW_NEWER_PHY; + if (hw->chip_rev < 3) + hw->flags |= SKY2_HW_FIFO_HANG_CHECK; + break; case CHIP_ID_YUKON_EC_U: @@ -2721,11 +2723,10 @@ static int __devinit sky2_init(struct sky2_hw *hw) dev_err(&hw->pdev->dev, "unsupported revision Yukon-EC rev A1\n"); return -EOPNOTSUPP; } - hw->flags = SKY2_HW_GIGABIT | SKY2_HW_RAMBUFFER; + hw->flags = SKY2_HW_GIGABIT | SKY2_HW_FIFO_HANG_CHECK; break; case CHIP_ID_YUKON_FE: - hw->flags = SKY2_HW_RAMBUFFER; break; case CHIP_ID_YUKON_FE_P: diff --git a/drivers/net/sky2.h b/drivers/net/sky2.h index 69cd984..8bc5c54 100644 --- a/drivers/net/sky2.h +++ b/drivers/net/sky2.h @@ -2063,7 +2063,7 @@ struct sky2_hw { #define SKY2_HW_FIBRE_PHY 0x00000002 #define SKY2_HW_GIGABIT 0x00000004 #define SKY2_HW_NEWER_PHY 0x00000008 -#define SKY2_HW_RAMBUFFER 0x00000010 /* chip has RAM FIFO */ +#define SKY2_HW_FIFO_HANG_CHECK 0x00000010 #define SKY2_HW_NEW_LE 0x00000020 /* new LSOv2 format */ #define SKY2_HW_AUTO_TX_SUM 0x00000040 /* new IP decode for Tx */ #define SKY2_HW_ADV_POWER_CTL 0x00000080 /* additional PHY power regs */ -- cgit v1.1 From 21c0f275085e5b884a409d75a7deb73ece6477fb Mon Sep 17 00:00:00 2001 From: Jeff Garzik Date: Tue, 25 Sep 2007 00:11:34 -0400 Subject: Revert "drivers/net/pcmcia/3c589_cs: fix port configuration switcheroo" This reverts commit fadacb1b80e35e0b36a90d43e21ef91eec4b889b. The change being reverted made the driver consistent with include/linux/netdevice.h, but then inconsistent with the other PCMCIA ethernet drivers. Signed-off-by: Jeff Garzik --- drivers/net/pcmcia/3c589_cs.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers/net') diff --git a/drivers/net/pcmcia/3c589_cs.c b/drivers/net/pcmcia/3c589_cs.c index c06cae3..503f268 100644 --- a/drivers/net/pcmcia/3c589_cs.c +++ b/drivers/net/pcmcia/3c589_cs.c @@ -116,7 +116,7 @@ struct el3_private { spinlock_t lock; }; -static const char *if_names[] = { "auto", "10base2", "10baseT", "AUI" }; +static const char *if_names[] = { "auto", "10baseT", "10base2", "AUI" }; /*====================================================================*/ -- cgit v1.1 From 45dfd5b5dd20f17fe23dafc5cfe921474d27f849 Mon Sep 17 00:00:00 2001 From: Michal Schmidt Date: Tue, 25 Sep 2007 23:05:39 -0700 Subject: [PPP_MPPE]: Don't put InterimKey on the stack Signed-off-by: Michal Schmidt Signed-off-by: David S. Miller --- drivers/net/ppp_mppe.c | 14 ++++++-------- 1 file changed, 6 insertions(+), 8 deletions(-) (limited to 'drivers/net') diff --git a/drivers/net/ppp_mppe.c b/drivers/net/ppp_mppe.c index f79cf87..c0b6d19 100644 --- a/drivers/net/ppp_mppe.c +++ b/drivers/net/ppp_mppe.c @@ -136,7 +136,7 @@ struct ppp_mppe_state { * Key Derivation, from RFC 3078, RFC 3079. * Equivalent to Get_Key() for MS-CHAP as described in RFC 3079. */ -static void get_new_key_from_sha(struct ppp_mppe_state * state, unsigned char *InterimKey) +static void get_new_key_from_sha(struct ppp_mppe_state * state) { struct hash_desc desc; struct scatterlist sg[4]; @@ -153,8 +153,6 @@ static void get_new_key_from_sha(struct ppp_mppe_state * state, unsigned char *I desc.flags = 0; crypto_hash_digest(&desc, sg, nbytes, state->sha1_digest); - - memcpy(InterimKey, state->sha1_digest, state->keylen); } /* @@ -163,21 +161,21 @@ static void get_new_key_from_sha(struct ppp_mppe_state * state, unsigned char *I */ static void mppe_rekey(struct ppp_mppe_state * state, int initial_key) { - unsigned char InterimKey[MPPE_MAX_KEY_LEN]; struct scatterlist sg_in[1], sg_out[1]; struct blkcipher_desc desc = { .tfm = state->arc4 }; - get_new_key_from_sha(state, InterimKey); + get_new_key_from_sha(state); if (!initial_key) { - crypto_blkcipher_setkey(state->arc4, InterimKey, state->keylen); - setup_sg(sg_in, InterimKey, state->keylen); + crypto_blkcipher_setkey(state->arc4, state->sha1_digest, + state->keylen); + setup_sg(sg_in, state->sha1_digest, state->keylen); setup_sg(sg_out, state->session_key, state->keylen); if (crypto_blkcipher_encrypt(&desc, sg_out, sg_in, state->keylen) != 0) { printk(KERN_WARNING "mppe_rekey: cipher_encrypt failed\n"); } } else { - memcpy(state->session_key, InterimKey, state->keylen); + memcpy(state->session_key, state->sha1_digest, state->keylen); } if (state->keylen == 8) { /* See RFC 3078 */ -- cgit v1.1 From d8c4a2f9d9e7827362fd7ab0b5d9637c6af5ac5b Mon Sep 17 00:00:00 2001 From: Al Viro Date: Wed, 26 Sep 2007 01:53:52 +0100 Subject: mv643xx_eth: duplicate methods in initializer Signed-off-by: Al Viro Signed-off-by: Linus Torvalds --- drivers/net/mv643xx_eth.c | 2 -- 1 file changed, 2 deletions(-) (limited to 'drivers/net') diff --git a/drivers/net/mv643xx_eth.c b/drivers/net/mv643xx_eth.c index 6a117e9..456d1e1 100644 --- a/drivers/net/mv643xx_eth.c +++ b/drivers/net/mv643xx_eth.c @@ -2768,8 +2768,6 @@ static const struct ethtool_ops mv643xx_ethtool_ops = { .get_stats_count = mv643xx_get_stats_count, .get_ethtool_stats = mv643xx_get_ethtool_stats, .get_strings = mv643xx_get_strings, - .get_stats_count = mv643xx_get_stats_count, - .get_ethtool_stats = mv643xx_get_ethtool_stats, .nway_reset = mv643xx_eth_nway_restart, }; -- cgit v1.1 From 3b12e0141f7a97c3b84731b5f935ed738bb6f960 Mon Sep 17 00:00:00 2001 From: Stephen Hemminger Date: Wed, 26 Sep 2007 17:58:47 -0700 Subject: sky2: sky2 FE+ receive status workaround The Yukon FE+ chip appears to have a hardware glitch that causes bogus receive status values to be posted. The data in the packet is good, but the status value is random garbage. As a temporary workaround until the problem is better understood, implement the workaround the vendor driver used of ignoring the status value on this chip. Since this means trusting dodgy hardware values; add additional checking of the receive packet length. Signed-off-by: Stephen Hemminger Signed-off-by: Jeff Garzik --- drivers/net/sky2.c | 28 +++++++++++++++++----------- 1 file changed, 17 insertions(+), 11 deletions(-) (limited to 'drivers/net') diff --git a/drivers/net/sky2.c b/drivers/net/sky2.c index 0792031..a3de0b6 100644 --- a/drivers/net/sky2.c +++ b/drivers/net/sky2.c @@ -2148,6 +2148,18 @@ static struct sk_buff *sky2_receive(struct net_device *dev, sky2->rx_next = (sky2->rx_next + 1) % sky2->rx_pending; prefetch(sky2->rx_ring + sky2->rx_next); + if (length < ETH_ZLEN || length > sky2->rx_data_size) + goto len_error; + + /* This chip has hardware problems that generates bogus status. + * So do only marginal checking and expect higher level protocols + * to handle crap frames. + */ + if (sky2->hw->chip_id == CHIP_ID_YUKON_FE_P && + sky2->hw->chip_rev == CHIP_REV_YU_FE2_A0 && + length != count) + goto okay; + if (status & GMR_FS_ANY_ERR) goto error; @@ -2156,8 +2168,9 @@ static struct sk_buff *sky2_receive(struct net_device *dev, /* if length reported by DMA does not match PHY, packet was truncated */ if (length != count) - goto len_mismatch; + goto len_error; +okay: if (length < copybreak) skb = receive_copy(sky2, re, length); else @@ -2167,13 +2180,13 @@ resubmit: return skb; -len_mismatch: +len_error: /* Truncation of overlength packets causes PHY length to not match MAC length */ ++sky2->net_stats.rx_length_errors; if (netif_msg_rx_err(sky2) && net_ratelimit()) - pr_info(PFX "%s: rx length mismatch: length %d status %#x\n", - dev->name, length, status); + pr_info(PFX "%s: rx length error: status %#x length %d\n", + dev->name, status, length); goto resubmit; error: @@ -3934,13 +3947,6 @@ static __devinit struct net_device *sky2_init_netdev(struct sky2_hw *hw, sky2->hw = hw; sky2->msg_enable = netif_msg_init(debug, default_msg); - /* This chip has hardware problems that generates - * bogus PHY receive status so by default shut up the message. - */ - if (hw->chip_id == CHIP_ID_YUKON_FE_P && - hw->chip_rev == CHIP_REV_YU_FE2_A0) - sky2->msg_enable &= ~NETIF_MSG_RX_ERR; - /* Auto speed and flow control */ sky2->autoneg = AUTONEG_ENABLE; sky2->flow_mode = FC_BOTH; -- cgit v1.1 From d6c9bc1ed4301cbc3df4565ff5348b64bf2a767c Mon Sep 17 00:00:00 2001 From: Stephen Hemminger Date: Thu, 27 Sep 2007 12:32:44 -0700 Subject: sky2: FE+ vlan workaround The FE+ workaround means the driver can no longer trust the status register to indicate VLAN tagged frames. The fix for this is to just disable VLAN acceleration for that chip version. Tested and works fine. Signed-off-by: Stephen Hemminger Signed-off-by: Jeff Garzik --- drivers/net/sky2.c | 8 ++++++-- 1 file changed, 6 insertions(+), 2 deletions(-) (limited to 'drivers/net') diff --git a/drivers/net/sky2.c b/drivers/net/sky2.c index a3de0b6..3bfc9d3 100644 --- a/drivers/net/sky2.c +++ b/drivers/net/sky2.c @@ -3970,8 +3970,12 @@ static __devinit struct net_device *sky2_init_netdev(struct sky2_hw *hw, dev->features |= NETIF_F_HIGHDMA; #ifdef SKY2_VLAN_TAG_USED - dev->features |= NETIF_F_HW_VLAN_TX | NETIF_F_HW_VLAN_RX; - dev->vlan_rx_register = sky2_vlan_rx_register; + /* The workaround for FE+ status conflicts with VLAN tag detection. */ + if (!(sky2->hw->chip_id == CHIP_ID_YUKON_FE_P && + sky2->hw->chip_rev == CHIP_REV_YU_FE2_A0)) { + dev->features |= NETIF_F_HW_VLAN_TX | NETIF_F_HW_VLAN_RX; + dev->vlan_rx_register = sky2_vlan_rx_register; + } #endif /* read the mac address */ -- cgit v1.1 From 88f5f0cad396be594d6d55cb2d0cd69e8df9ab16 Mon Sep 17 00:00:00 2001 From: Stephen Hemminger Date: Thu, 27 Sep 2007 12:38:12 -0700 Subject: sky2: fix transmit state on resume This should fix http://bugzilla.kernel.org/show_bug.cgi?id=8667 After resume, driver has reset the chip so the current state of transmit checksum offload state machine and DMA state machine will be undefined. The fix is to set the state so that first Tx will set MSS and offset values. Signed-off-by: Stephen Hemminger Signed-off-by: Jeff Garzik --- drivers/net/sky2.c | 17 ++++++++++++++++- 1 file changed, 16 insertions(+), 1 deletion(-) (limited to 'drivers/net') diff --git a/drivers/net/sky2.c b/drivers/net/sky2.c index 3bfc9d3..162489b 100644 --- a/drivers/net/sky2.c +++ b/drivers/net/sky2.c @@ -910,6 +910,20 @@ static inline struct sky2_tx_le *get_tx_le(struct sky2_port *sky2) return le; } +static void tx_init(struct sky2_port *sky2) +{ + struct sky2_tx_le *le; + + sky2->tx_prod = sky2->tx_cons = 0; + sky2->tx_tcpsum = 0; + sky2->tx_last_mss = 0; + + le = get_tx_le(sky2); + le->addr = 0; + le->opcode = OP_ADDR64 | HW_OWNER; + sky2->tx_addr64 = 0; +} + static inline struct tx_ring_info *tx_le_re(struct sky2_port *sky2, struct sky2_tx_le *le) { @@ -1320,7 +1334,8 @@ static int sky2_up(struct net_device *dev) GFP_KERNEL); if (!sky2->tx_ring) goto err_out; - sky2->tx_prod = sky2->tx_cons = 0; + + tx_init(sky2); sky2->rx_le = pci_alloc_consistent(hw->pdev, RX_LE_BYTES, &sky2->rx_le_map); -- cgit v1.1 From f4ec7f98714c2c0b7afa422c0cba6fb5c875c2c2 Mon Sep 17 00:00:00 2001 From: Auke Kok Date: Thu, 30 Aug 2007 11:23:58 -0700 Subject: e1000: Add device IDs of blade version of the 82571 quad port This blade-specific board form factor is identical to the 82571EB board. Signed-off-by: Auke Kok Signed-off-by: Jeff Garzik --- drivers/net/e1000/e1000_ethtool.c | 1 + drivers/net/e1000/e1000_hw.c | 1 + drivers/net/e1000/e1000_hw.h | 1 + drivers/net/e1000/e1000_main.c | 2 ++ 4 files changed, 5 insertions(+) (limited to 'drivers/net') diff --git a/drivers/net/e1000/e1000_ethtool.c b/drivers/net/e1000/e1000_ethtool.c index 4c3785c..9ecc3ad 100644 --- a/drivers/net/e1000/e1000_ethtool.c +++ b/drivers/net/e1000/e1000_ethtool.c @@ -1726,6 +1726,7 @@ static int e1000_wol_exclusion(struct e1000_adapter *adapter, struct ethtool_wol case E1000_DEV_ID_82571EB_QUAD_COPPER: case E1000_DEV_ID_82571EB_QUAD_FIBER: case E1000_DEV_ID_82571EB_QUAD_COPPER_LOWPROFILE: + case E1000_DEV_ID_82571PT_QUAD_COPPER: case E1000_DEV_ID_82546GB_QUAD_COPPER_KSP3: /* quad port adapters only support WoL on port A */ if (!adapter->quad_port_a) { diff --git a/drivers/net/e1000/e1000_hw.c b/drivers/net/e1000/e1000_hw.c index ba120f7..8604adb 100644 --- a/drivers/net/e1000/e1000_hw.c +++ b/drivers/net/e1000/e1000_hw.c @@ -387,6 +387,7 @@ e1000_set_mac_type(struct e1000_hw *hw) case E1000_DEV_ID_82571EB_SERDES_DUAL: case E1000_DEV_ID_82571EB_SERDES_QUAD: case E1000_DEV_ID_82571EB_QUAD_COPPER: + case E1000_DEV_ID_82571PT_QUAD_COPPER: case E1000_DEV_ID_82571EB_QUAD_FIBER: case E1000_DEV_ID_82571EB_QUAD_COPPER_LOWPROFILE: hw->mac_type = e1000_82571; diff --git a/drivers/net/e1000/e1000_hw.h b/drivers/net/e1000/e1000_hw.h index fe87146..07f0ea7 100644 --- a/drivers/net/e1000/e1000_hw.h +++ b/drivers/net/e1000/e1000_hw.h @@ -475,6 +475,7 @@ int32_t e1000_check_phy_reset_block(struct e1000_hw *hw); #define E1000_DEV_ID_82571EB_FIBER 0x105F #define E1000_DEV_ID_82571EB_SERDES 0x1060 #define E1000_DEV_ID_82571EB_QUAD_COPPER 0x10A4 +#define E1000_DEV_ID_82571PT_QUAD_COPPER 0x10D5 #define E1000_DEV_ID_82571EB_QUAD_FIBER 0x10A5 #define E1000_DEV_ID_82571EB_QUAD_COPPER_LOWPROFILE 0x10BC #define E1000_DEV_ID_82571EB_SERDES_DUAL 0x10D9 diff --git a/drivers/net/e1000/e1000_main.c b/drivers/net/e1000/e1000_main.c index 4a22595..e7c8951 100644 --- a/drivers/net/e1000/e1000_main.c +++ b/drivers/net/e1000/e1000_main.c @@ -108,6 +108,7 @@ static struct pci_device_id e1000_pci_tbl[] = { INTEL_E1000_ETHERNET_DEVICE(0x10BC), INTEL_E1000_ETHERNET_DEVICE(0x10C4), INTEL_E1000_ETHERNET_DEVICE(0x10C5), + INTEL_E1000_ETHERNET_DEVICE(0x10D5), INTEL_E1000_ETHERNET_DEVICE(0x10D9), INTEL_E1000_ETHERNET_DEVICE(0x10DA), /* required last entry */ @@ -1101,6 +1102,7 @@ e1000_probe(struct pci_dev *pdev, case E1000_DEV_ID_82571EB_QUAD_COPPER: case E1000_DEV_ID_82571EB_QUAD_FIBER: case E1000_DEV_ID_82571EB_QUAD_COPPER_LOWPROFILE: + case E1000_DEV_ID_82571PT_QUAD_COPPER: /* if quad port adapter, disable WoL on all but port A */ if (global_quad_port_a != 0) adapter->eeprom_wol = 0; -- cgit v1.1 From 2bcff60f7ce88c09a2bc1302ff14510737bfcb7b Mon Sep 17 00:00:00 2001 From: Dale Farnsworth Date: Fri, 28 Sep 2007 06:30:43 -0700 Subject: mv643xx_eth: Check ETH_INT_CAUSE_STATE bit Commit 468d09f8946d40228c56de26fe4874b2f98067ed masked the "state" interrupt (bit 20 of the cause register). This results in Radstone's PPC7D repeatedly re-entering the interrupt routine, locking up the board. The following patch returns the required handling for this interrupt. Signed-off-by: Martyn Welch Signed-off-by: Dale Farnsworth Signed-off-by: Jeff Garzik --- drivers/net/mv643xx_eth.c | 2 +- drivers/net/mv643xx_eth.h | 4 +++- 2 files changed, 4 insertions(+), 2 deletions(-) (limited to 'drivers/net') diff --git a/drivers/net/mv643xx_eth.c b/drivers/net/mv643xx_eth.c index 456d1e1..34288fe 100644 --- a/drivers/net/mv643xx_eth.c +++ b/drivers/net/mv643xx_eth.c @@ -534,7 +534,7 @@ static irqreturn_t mv643xx_eth_int_handler(int irq, void *dev_id) } /* PHY status changed */ - if (eth_int_cause_ext & ETH_INT_CAUSE_PHY) { + if (eth_int_cause_ext & (ETH_INT_CAUSE_PHY | ETH_INT_CAUSE_STATE)) { struct ethtool_cmd cmd; if (mii_link_ok(&mp->mii)) { diff --git a/drivers/net/mv643xx_eth.h b/drivers/net/mv643xx_eth.h index 82f8c0c..565b966 100644 --- a/drivers/net/mv643xx_eth.h +++ b/drivers/net/mv643xx_eth.h @@ -64,7 +64,9 @@ #define ETH_INT_CAUSE_TX_ERROR (ETH_TX_QUEUES_ENABLED << 8) #define ETH_INT_CAUSE_TX (ETH_INT_CAUSE_TX_DONE | ETH_INT_CAUSE_TX_ERROR) #define ETH_INT_CAUSE_PHY 0x00010000 -#define ETH_INT_UNMASK_ALL_EXT (ETH_INT_CAUSE_TX | ETH_INT_CAUSE_PHY) +#define ETH_INT_CAUSE_STATE 0x00100000 +#define ETH_INT_UNMASK_ALL_EXT (ETH_INT_CAUSE_TX | ETH_INT_CAUSE_PHY | \ + ETH_INT_CAUSE_STATE) #define ETH_INT_MASK_ALL 0x00000000 #define ETH_INT_MASK_ALL_EXT 0x00000000 -- cgit v1.1 From f998351c755a0e87785f2616c4f91f1b3b19b149 Mon Sep 17 00:00:00 2001 From: Randy Dunlap Date: Sun, 30 Sep 2007 20:35:39 -0400 Subject: [PATCH] libertas: build problems when partially modular Fix missing symbols in libertas USB driver when it is modular and rest of libertas is built-in. Signed-off-by: Randy Dunlap Signed-off-by: John W. Linville --- drivers/net/wireless/Makefile | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers/net') diff --git a/drivers/net/wireless/Makefile b/drivers/net/wireless/Makefile index ef35bc6..4eb6d97 100644 --- a/drivers/net/wireless/Makefile +++ b/drivers/net/wireless/Makefile @@ -43,7 +43,7 @@ obj-$(CONFIG_PCMCIA_RAYCS) += ray_cs.o obj-$(CONFIG_PCMCIA_WL3501) += wl3501_cs.o obj-$(CONFIG_USB_ZD1201) += zd1201.o -obj-$(CONFIG_LIBERTAS_USB) += libertas/ +obj-$(CONFIG_LIBERTAS) += libertas/ rtl8187-objs := rtl8187_dev.o rtl8187_rtl8225.o obj-$(CONFIG_RTL8187) += rtl8187.o -- cgit v1.1 From b323e0e49fe9331ee3a7a336af879d6e303b16b3 Mon Sep 17 00:00:00 2001 From: Ron Mercer Date: Mon, 1 Oct 2007 11:43:22 -0700 Subject: qla3xxx: bugfix: Add memory barrier before accessing rx completion. Signed-off-by: Ron Mercer Signed-off-by: Jeff Garzik --- drivers/net/qla3xxx.c | 1 + 1 file changed, 1 insertion(+) (limited to 'drivers/net') diff --git a/drivers/net/qla3xxx.c b/drivers/net/qla3xxx.c index 69da95b..c3fe1c7 100755 --- a/drivers/net/qla3xxx.c +++ b/drivers/net/qla3xxx.c @@ -2248,6 +2248,7 @@ static int ql_tx_rx_clean(struct ql3_adapter *qdev, qdev->rsp_consumer_index) && (work_done < work_to_do)) { net_rsp = qdev->rsp_current; + rmb(); switch (net_rsp->opcode) { case OPCODE_OB_MAC_IOCB_FN0: -- cgit v1.1 From 50626297b1beb0a29c0f174be39f36485533216c Mon Sep 17 00:00:00 2001 From: Ron Mercer Date: Mon, 1 Oct 2007 11:43:23 -0700 Subject: qla3xxx: bugfix: Fix VLAN rx completion handling. Fix 4032 chip undocumented "feature" where bit-8 is set if the inbound completion is for a VLAN. Signed-off-by: Ron Mercer Signed-off-by: Jeff Garzik --- drivers/net/qla3xxx.c | 6 ++++++ 1 file changed, 6 insertions(+) (limited to 'drivers/net') diff --git a/drivers/net/qla3xxx.c b/drivers/net/qla3xxx.c index c3fe1c7..ea15131 100755 --- a/drivers/net/qla3xxx.c +++ b/drivers/net/qla3xxx.c @@ -2249,6 +2249,12 @@ static int ql_tx_rx_clean(struct ql3_adapter *qdev, net_rsp = qdev->rsp_current; rmb(); + /* + * Fix 4032 chipe undocumented "feature" where bit-8 is set if the + * inbound completion is for a VLAN. + */ + if (qdev->device_id == QL3032_DEVICE_ID) + net_rsp->opcode &= 0x7f; switch (net_rsp->opcode) { case OPCODE_OB_MAC_IOCB_FN0: -- cgit v1.1 From 593ff56ef2a23ed3a66ee87d9c9b33044b9fb193 Mon Sep 17 00:00:00 2001 From: Dale Farnsworth Date: Mon, 1 Oct 2007 16:02:18 -0700 Subject: mv643xx_eth: Do not modify struct netdev tx_queue_len This driver erroneously zeros dev->tx_queue_len, since mp->tx_ring_size has not yet been initialized. Actually, the driver shouldn't modify tx_queue_len at all and should leave the value set by alloc_etherdev(), currently 1000. Signed-off-by: Dale Farnsworth Signed-off-by: Jeff Garzik --- drivers/net/mv643xx_eth.c | 1 - 1 file changed, 1 deletion(-) (limited to 'drivers/net') diff --git a/drivers/net/mv643xx_eth.c b/drivers/net/mv643xx_eth.c index 34288fe..3153356 100644 --- a/drivers/net/mv643xx_eth.c +++ b/drivers/net/mv643xx_eth.c @@ -1357,7 +1357,6 @@ static int mv643xx_eth_probe(struct platform_device *pdev) #endif dev->watchdog_timeo = 2 * HZ; - dev->tx_queue_len = mp->tx_ring_size; dev->base_addr = 0; dev->change_mtu = mv643xx_eth_change_mtu; dev->do_ioctl = mv643xx_eth_do_ioctl; -- cgit v1.1 From f662fe5a0b144efadbfc00e8040e603ec318746e Mon Sep 17 00:00:00 2001 From: Peter Korsgaard Date: Mon, 1 Oct 2007 13:36:07 +0200 Subject: dm9601: Fix receive MTU dm9601 didn't take the ethernet header into account when calculating RX MTU, causing packets bigger than 1486 to fail. Signed-off-by: Peter Korsgaard Signed-off-by: Jeff Garzik --- drivers/net/usb/dm9601.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers/net') diff --git a/drivers/net/usb/dm9601.c b/drivers/net/usb/dm9601.c index 16c7a0e..a2de32f 100644 --- a/drivers/net/usb/dm9601.c +++ b/drivers/net/usb/dm9601.c @@ -405,7 +405,7 @@ static int dm9601_bind(struct usbnet *dev, struct usb_interface *intf) dev->net->ethtool_ops = &dm9601_ethtool_ops; dev->net->hard_header_len += DM_TX_OVERHEAD; dev->hard_mtu = dev->net->mtu + dev->net->hard_header_len; - dev->rx_urb_size = dev->net->mtu + DM_RX_OVERHEAD; + dev->rx_urb_size = dev->net->mtu + ETH_HLEN + DM_RX_OVERHEAD; dev->mii.dev = dev->net; dev->mii.mdio_read = dm9601_mdio_read; -- cgit v1.1