/* * Customer code to add GPIO control during WLAN start/stop * Copyright (C) 1999-2012, Broadcom Corporation * * Unless you and Broadcom execute a separate written software license * agreement governing use of this software, this software is licensed to you * under the terms of the GNU General Public License version 2 (the "GPL"), * available at http://www.broadcom.com/licenses/GPLv2.php, with the * following added to such license: * * As a special exception, the copyright holders of this software give you * permission to link this software with independent modules, and to copy and * distribute the resulting executable under terms of your choice, provided that * you also meet, for each linked independent module, the terms and conditions of * the license of that module. An independent module is a module which is not * derived from this software. The special exception does not apply to any * modifications of the software. * * Notwithstanding the above, under no circumstances may you combine this * software in any way with any other Broadcom software provided under a license * other than the GPL, without Broadcom's express prior written consent. * * $Id: dhd_custom_gpio.c 353167 2012-08-24 22:11:30Z $ */ #include #include #include #include #include #include #include #include #define WL_ERROR(x) printf x #define WL_TRACE(x) #ifdef CUSTOMER_HW extern void bcm_wlan_power_off(int); extern void bcm_wlan_power_on(int); #endif /* CUSTOMER_HW */ #if defined(CUSTOMER_HW2) || defined(CUSTOMER_HW4) #ifdef CONFIG_WIFI_CONTROL_FUNC int wifi_set_power(int on, unsigned long msec); int wifi_get_irq_number(unsigned long *irq_flags_ptr); int wifi_get_mac_addr(unsigned char *buf); void *wifi_get_country_code(char *ccode); #else int wifi_set_power(int on, unsigned long msec) { return -1; } int wifi_get_irq_number(unsigned long *irq_flags_ptr) { return -1; } int wifi_get_mac_addr(unsigned char *buf) { return -1; } void *wifi_get_country_code(char *ccode) { return NULL; } #endif /* CONFIG_WIFI_CONTROL_FUNC */ #endif /* CUSTOMER_HW2 || CUSTOMER_HW4 */ #if defined(OOB_INTR_ONLY) || defined(BCMSPI_ANDROID) #if defined(BCMLXSDMMC) extern int sdioh_mmc_irq(int irq); #endif /* (BCMLXSDMMC) */ #ifdef CUSTOMER_HW3 #include #endif /* Customer specific Host GPIO defintion */ static int dhd_oob_gpio_num = -1; module_param(dhd_oob_gpio_num, int, 0644); MODULE_PARM_DESC(dhd_oob_gpio_num, "DHD oob gpio number"); /* This function will return: * 1) return : Host gpio interrupt number per customer platform * 2) irq_flags_ptr : Type of Host interrupt as Level or Edge * * NOTE : * Customer should check his platform definitions * and his Host Interrupt spec * to figure out the proper setting for his platform. * Broadcom provides just reference settings as example. * */ int dhd_customer_oob_irq_map(unsigned long *irq_flags_ptr) { int host_oob_irq = 0; #if defined(CUSTOMER_HW2) || defined(CUSTOMER_HW4) host_oob_irq = wifi_get_irq_number(irq_flags_ptr); #else #if defined(CUSTOM_OOB_GPIO_NUM) if (dhd_oob_gpio_num < 0) { dhd_oob_gpio_num = CUSTOM_OOB_GPIO_NUM; } #endif /* CUSTOMER_OOB_GPIO_NUM */ if (dhd_oob_gpio_num < 0) { WL_ERROR(("%s: ERROR customer specific Host GPIO is NOT defined \n", __FUNCTION__)); return (dhd_oob_gpio_num); } WL_ERROR(("%s: customer specific Host GPIO number is (%d)\n", __FUNCTION__, dhd_oob_gpio_num)); #if defined CUSTOMER_HW host_oob_irq = MSM_GPIO_TO_INT(dhd_oob_gpio_num); #elif defined CUSTOMER_HW3 gpio_request(dhd_oob_gpio_num, "oob irq"); host_oob_irq = gpio_to_irq(dhd_oob_gpio_num); gpio_direction_input(dhd_oob_gpio_num); #endif /* CUSTOMER_HW */ #endif /* CUSTOMER_HW2 || CUSTOMER_HW4 */ return (host_oob_irq); } #endif /* defined(OOB_INTR_ONLY) || defined(BCMSPI_ANDROID) */ /* Customer function to control hw specific wlan gpios */ void dhd_customer_gpio_wlan_ctrl(int onoff) { switch (onoff) { case WLAN_RESET_OFF: WL_TRACE(("%s: call customer specific GPIO to insert WLAN RESET\n", __FUNCTION__)); #ifdef CUSTOMER_HW bcm_wlan_power_off(2); #endif /* CUSTOMER_HW */ #if defined(CUSTOMER_HW2) || defined(CUSTOMER_HW4) wifi_set_power(0, 0); #endif WL_ERROR(("=========== WLAN placed in RESET ========\n")); break; case WLAN_RESET_ON: WL_TRACE(("%s: callc customer specific GPIO to remove WLAN RESET\n", __FUNCTION__)); #ifdef CUSTOMER_HW bcm_wlan_power_on(2); #endif /* CUSTOMER_HW */ #if defined(CUSTOMER_HW2) || defined(CUSTOMER_HW4) wifi_set_power(1, 0); #endif WL_ERROR(("=========== WLAN going back to live ========\n")); break; case WLAN_POWER_OFF: WL_TRACE(("%s: call customer specific GPIO to turn off WL_REG_ON\n", __FUNCTION__)); #ifdef CUSTOMER_HW bcm_wlan_power_off(1); #endif /* CUSTOMER_HW */ break; case WLAN_POWER_ON: WL_TRACE(("%s: call customer specific GPIO to turn on WL_REG_ON\n", __FUNCTION__)); #ifdef CUSTOMER_HW bcm_wlan_power_on(1); /* Lets customer power to get stable */ OSL_DELAY(200); #endif /* CUSTOMER_HW */ break; } } #ifdef GET_CUSTOM_MAC_ENABLE /* Function to get custom MAC address */ int dhd_custom_get_mac_address(unsigned char *buf) { int ret = 0; WL_TRACE(("%s Enter\n", __FUNCTION__)); if (!buf) return -EINVAL; /* Customer access to MAC address stored outside of DHD driver */ #if defined(CUSTOMER_HW2) && (LINUX_VERSION_CODE >= KERNEL_VERSION(2, 6, 35)) ret = wifi_get_mac_addr(buf); #endif #ifdef EXAMPLE_GET_MAC /* EXAMPLE code */ { struct ether_addr ea_example = {{0x00, 0x11, 0x22, 0x33, 0x44, 0xFF}}; bcopy((char *)&ea_example, buf, sizeof(struct ether_addr)); } #endif /* EXAMPLE_GET_MAC */ return ret; } #endif /* GET_CUSTOM_MAC_ENABLE */ #ifndef CUSTOMER_HW4 /* Customized Locale table : OPTIONAL feature */ const struct cntry_locales_custom translate_custom_table[] = { /* Table should be filled out based on custom platform regulatory requirement */ #ifdef EXAMPLE_TABLE {"", "XY", 4}, /* Universal if Country code is unknown or empty */ {"US", "US", 69}, /* input ISO "US" to : US regrev 69 */ {"CA", "US", 69}, /* input ISO "CA" to : US regrev 69 */ {"EU", "EU", 5}, /* European union countries to : EU regrev 05 */ {"AT", "EU", 5}, {"BE", "EU", 5}, {"BG", "EU", 5}, {"CY", "EU", 5}, {"CZ", "EU", 5}, {"DK", "EU", 5}, {"EE", "EU", 5}, {"FI", "EU", 5}, {"FR", "EU", 5}, {"DE", "EU", 5}, {"GR", "EU", 5}, {"HU", "EU", 5}, {"IE", "EU", 5}, {"IT", "EU", 5}, {"LV", "EU", 5}, {"LI", "EU", 5}, {"LT", "EU", 5}, {"LU", "EU", 5}, {"MT", "EU", 5}, {"NL", "EU", 5}, {"PL", "EU", 5}, {"PT", "EU", 5}, {"RO", "EU", 5}, {"SK", "EU", 5}, {"SI", "EU", 5}, {"ES", "EU", 5}, {"SE", "EU", 5}, {"GB", "EU", 5}, {"KR", "XY", 3}, {"AU", "XY", 3}, {"CN", "XY", 3}, /* input ISO "CN" to : XY regrev 03 */ {"TW", "XY", 3}, {"AR", "XY", 3}, {"MX", "XY", 3}, {"IL", "IL", 0}, {"CH", "CH", 0}, {"TR", "TR", 0}, {"NO", "NO", 0}, #endif /* EXMAPLE_TABLE */ }; /* Customized Locale convertor * input : ISO 3166-1 country abbreviation * output: customized cspec */ void get_customized_country_code(char *country_iso_code, wl_country_t *cspec) { #if defined(CUSTOMER_HW2) && (LINUX_VERSION_CODE >= KERNEL_VERSION(2, 6, 39)) struct cntry_locales_custom *cloc_ptr; if (!cspec) return; cloc_ptr = wifi_get_country_code(country_iso_code); if (cloc_ptr) { strlcpy(cspec->ccode, cloc_ptr->custom_locale, WLC_CNTRY_BUF_SZ); cspec->rev = cloc_ptr->custom_locale_rev; } return; #else int size, i; size = ARRAYSIZE(translate_custom_table); if (cspec == 0) return; if (size == 0) return; for (i = 0; i < size; i++) { if (strcmp(country_iso_code, translate_custom_table[i].iso_abbrev) == 0) { memcpy(cspec->ccode, translate_custom_table[i].custom_locale, WLC_CNTRY_BUF_SZ); cspec->rev = translate_custom_table[i].custom_locale_rev; return; } } #ifdef EXAMPLE_TABLE /* if no country code matched return first universal code from translate_custom_table */ memcpy(cspec->ccode, translate_custom_table[0].custom_locale, WLC_CNTRY_BUF_SZ); cspec->rev = translate_custom_table[0].custom_locale_rev; #endif /* EXMAPLE_TABLE */ return; #endif /* defined(CUSTOMER_HW2) && (LINUX_VERSION_CODE >= KERNEL_VERSION(2, 6, 36)) */ } #endif /* CUSTOMER_HW4 */