aboutsummaryrefslogtreecommitdiffstats
path: root/drivers/net/sfc/sfe4001.c
blob: b27849523990e0d9e43f8ff2262dc7c843e955de (plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
/****************************************************************************
 * Driver for Solarflare Solarstorm network controllers and boards
 * Copyright 2007 Solarflare Communications Inc.
 *
 * This program is free software; you can redistribute it and/or modify it
 * under the terms of the GNU General Public License version 2 as published
 * by the Free Software Foundation, incorporated herein by reference.
 */

/*****************************************************************************
 * Support for the SFE4001 NIC: driver code for the PCA9539 I/O expander that
 * controls the PHY power rails, and for the MAX6647 temp. sensor used to check
 * the PHY
 */
#include <linux/delay.h>
#include "efx.h"
#include "phy.h"
#include "boards.h"
#include "falcon.h"
#include "falcon_hwdefs.h"
#include "mac.h"

/**************************************************************************
 *
 * I2C IO Expander device
 *
 **************************************************************************/
#define	PCA9539 0x74

#define	P0_IN 0x00
#define	P0_OUT 0x02
#define	P0_INVERT 0x04
#define	P0_CONFIG 0x06

#define	P0_EN_1V0X_LBN 0
#define	P0_EN_1V0X_WIDTH 1
#define	P0_EN_1V2_LBN 1
#define	P0_EN_1V2_WIDTH 1
#define	P0_EN_2V5_LBN 2
#define	P0_EN_2V5_WIDTH 1
#define	P0_EN_3V3X_LBN 3
#define	P0_EN_3V3X_WIDTH 1
#define	P0_EN_5V_LBN 4
#define	P0_EN_5V_WIDTH 1
#define	P0_SHORTEN_JTAG_LBN 5
#define	P0_SHORTEN_JTAG_WIDTH 1
#define	P0_X_TRST_LBN 6
#define	P0_X_TRST_WIDTH 1
#define	P0_DSP_RESET_LBN 7
#define	P0_DSP_RESET_WIDTH 1

#define	P1_IN 0x01
#define	P1_OUT 0x03
#define	P1_INVERT 0x05
#define	P1_CONFIG 0x07

#define	P1_AFE_PWD_LBN 0
#define	P1_AFE_PWD_WIDTH 1
#define	P1_DSP_PWD25_LBN 1
#define	P1_DSP_PWD25_WIDTH 1
#define	P1_RESERVED_LBN 2
#define	P1_RESERVED_WIDTH 2
#define	P1_SPARE_LBN 4
#define	P1_SPARE_WIDTH 4


/**************************************************************************
 *
 * Temperature Sensor
 *
 **************************************************************************/
#define	MAX6647	0x4e

#define	RLTS	0x00
#define	RLTE	0x01
#define	RSL	0x02
#define	RCL	0x03
#define	RCRA	0x04
#define	RLHN	0x05
#define	RLLI	0x06
#define	RRHI	0x07
#define	RRLS	0x08
#define	WCRW	0x0a
#define	WLHO	0x0b
#define	WRHA	0x0c
#define	WRLN	0x0e
#define	OSHT	0x0f
#define	REET	0x10
#define	RIET	0x11
#define	RWOE	0x19
#define	RWOI	0x20
#define	HYS	0x21
#define	QUEUE	0x22
#define	MFID	0xfe
#define	REVID	0xff

/* Status bits */
#define MAX6647_BUSY	(1 << 7)	/* ADC is converting */
#define MAX6647_LHIGH	(1 << 6)	/* Local high temp. alarm */
#define MAX6647_LLOW	(1 << 5)	/* Local low temp. alarm */
#define MAX6647_RHIGH	(1 << 4)	/* Remote high temp. alarm */
#define MAX6647_RLOW	(1 << 3)	/* Remote low temp. alarm */
#define MAX6647_FAULT	(1 << 2)	/* DXN/DXP short/open circuit */
#define MAX6647_EOT	(1 << 1)	/* Remote junction overtemp. */
#define MAX6647_IOT	(1 << 0)	/* Local junction overtemp. */

static const u8 xgphy_max_temperature = 90;

static void sfe4001_poweroff(struct efx_nic *efx)
{
	struct i2c_client *ioexp_client = efx->board_info.ioexp_client;
	struct i2c_client *hwmon_client = efx->board_info.hwmon_client;

	/* Turn off all power rails and disable outputs */
	i2c_smbus_write_byte_data(ioexp_client, P0_OUT, 0xff);
	i2c_smbus_write_byte_data(ioexp_client, P1_CONFIG, 0xff);
	i2c_smbus_write_byte_data(ioexp_client, P0_CONFIG, 0xff);

	/* Clear any over-temperature alert */
	i2c_smbus_read_byte_data(hwmon_client, RSL);
}

static void sfe4001_fini(struct efx_nic *efx)
{
	EFX_INFO(efx, "%s\n", __func__);

	sfe4001_poweroff(efx);
 	i2c_unregister_device(efx->board_info.ioexp_client);
 	i2c_unregister_device(efx->board_info.hwmon_client);
}

/* The P0_EN_3V3X line on SFE4001 boards (from A2 onward) is connected
 * to the FLASH_CFG_1 input on the DSP.  We must keep it high at power-
 * up to allow writing the flash (done through MDIO from userland).
 */
unsigned int sfe4001_phy_flash_cfg;
module_param_named(phy_flash_cfg, sfe4001_phy_flash_cfg, uint, 0444);
MODULE_PARM_DESC(phy_flash_cfg,
		 "Force PHY to enter flash configuration mode");

/* This board uses an I2C expander to provider power to the PHY, which needs to
 * be turned on before the PHY can be used.
 * Context: Process context, rtnl lock held
 */
int sfe4001_init(struct efx_nic *efx)
{
	struct i2c_client *hwmon_client, *ioexp_client;
	unsigned int count;
	int rc;
	u8 out;
	efx_dword_t reg;

	hwmon_client = i2c_new_dummy(&efx->i2c_adap, MAX6647);
	if (!hwmon_client)
		return -EIO;
	efx->board_info.hwmon_client = hwmon_client;

	ioexp_client = i2c_new_dummy(&efx->i2c_adap, PCA9539);
	if (!ioexp_client) {
		rc = -EIO;
		goto fail_hwmon;
	}
	efx->board_info.ioexp_client = ioexp_client;

	/* 10Xpress has fixed-function LED pins, so there is no board-specific
	 * blink code. */
	efx->board_info.blink = tenxpress_phy_blink;

	/* Ensure that XGXS and XAUI SerDes are held in reset */
	EFX_POPULATE_DWORD_7(reg, XX_PWRDNA_EN, 1,
			     XX_PWRDNB_EN, 1,
			     XX_RSTPLLAB_EN, 1,
			     XX_RESETA_EN, 1,
			     XX_RESETB_EN, 1,
			     XX_RSTXGXSRX_EN, 1,
			     XX_RSTXGXSTX_EN, 1);
	falcon_xmac_writel(efx, &reg, XX_PWR_RST_REG_MAC);
	udelay(10);

	efx->board_info.fini = sfe4001_fini;

	/* Set DSP over-temperature alert threshold */
	EFX_INFO(efx, "DSP cut-out at %dC\n", xgphy_max_temperature);
	rc = i2c_smbus_write_byte_data(hwmon_client, WLHO,
				       xgphy_max_temperature);
	if (rc)
		goto fail_ioexp;

	/* Read it back and verify */
	rc = i2c_smbus_read_byte_data(hwmon_client, RLHN);
	if (rc < 0)
		goto fail_ioexp;
	if (rc != xgphy_max_temperature) {
		rc = -EFAULT;
		goto fail_ioexp;
	}

	/* Clear any previous over-temperature alert */
	rc = i2c_smbus_read_byte_data(hwmon_client, RSL);
	if (rc < 0)
		goto fail_ioexp;

	/* Enable port 0 and port 1 outputs on IO expander */
	rc = i2c_smbus_write_byte_data(ioexp_client, P0_CONFIG, 0x00);
	if (rc)
		goto fail_ioexp;
	rc = i2c_smbus_write_byte_data(ioexp_client, P1_CONFIG,
				       0xff & ~(1 << P1_SPARE_LBN));
	if (rc)
		goto fail_on;

	/* Turn all power off then wait 1 sec. This ensures PHY is reset */
	out = 0xff & ~((0 << P0_EN_1V2_LBN) | (0 << P0_EN_2V5_LBN) |
		       (0 << P0_EN_3V3X_LBN) | (0 << P0_EN_5V_LBN) |
		       (0 << P0_EN_1V0X_LBN));
	rc = i2c_smbus_write_byte_data(ioexp_client, P0_OUT, out);
	if (rc)
		goto fail_on;

	schedule_timeout_uninterruptible(HZ);
	count = 0;
	do {
		/* Turn on 1.2V, 2.5V, 3.3V and 5V power rails */
		out = 0xff & ~((1 << P0_EN_1V2_LBN) | (1 << P0_EN_2V5_LBN) |
			       (1 << P0_EN_3V3X_LBN) | (1 << P0_EN_5V_LBN) |
			       (1 << P0_X_TRST_LBN));
		if (sfe4001_phy_flash_cfg)
			out |= 1 << P0_EN_3V3X_LBN;

		rc = i2c_smbus_write_byte_data(ioexp_client, P0_OUT, out);
		if (rc)
			goto fail_on;
		msleep(10);

		/* Turn on 1V power rail */
		out &= ~(1 << P0_EN_1V0X_LBN);
		rc = i2c_smbus_write_byte_data(ioexp_client, P0_OUT, out);
		if (rc)
			goto fail_on;

		EFX_INFO(efx, "waiting for power (attempt %d)...\n", count);

		schedule_timeout_uninterruptible(HZ);

		/* Check DSP is powered */
		rc = i2c_smbus_read_byte_data(ioexp_client, P1_IN);
		if (rc < 0)
			goto fail_on;
		if (rc & (1 << P1_AFE_PWD_LBN))
			goto done;

		/* DSP doesn't look powered in flash config mode */
		if (sfe4001_phy_flash_cfg)
			goto done;
	} while (++count < 20);

	EFX_INFO(efx, "timed out waiting for power\n");
	rc = -ETIMEDOUT;
	goto fail_on;

done:
	EFX_INFO(efx, "PHY is powered on\n");
	return 0;

fail_on:
	sfe4001_poweroff(efx);
fail_ioexp:
 	i2c_unregister_device(ioexp_client);
fail_hwmon:
 	i2c_unregister_device(hwmon_client);
	return rc;
}