blob: ba2643a43c73c662236ad8f79144dba39d5dcfad (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
|
config MAC80211
tristate "Generic IEEE 802.11 Networking Stack (mac80211)"
depends on CFG80211
select CRYPTO
select CRYPTO_ECB
select CRYPTO_ARC4
select CRYPTO_AES
select CRC32
select WIRELESS_EXT
---help---
This option enables the hardware independent IEEE 802.11
networking stack.
comment "CFG80211 needs to be enabled for MAC80211"
depends on CFG80211=n
config MAC80211_DEFAULT_PS
bool "enable powersave by default"
depends on MAC80211
default y
help
This option enables powersave mode by default.
If this causes your applications to misbehave you should fix your
applications instead -- they need to register their network
latency requirement, see Documentation/power/pm_qos_interface.txt.
config MAC80211_DEFAULT_PS_VALUE
int
default 1 if MAC80211_DEFAULT_PS
default 0
menu "Rate control algorithm selection"
depends on MAC80211 != n
config MAC80211_RC_PID
bool "PID controller based rate control algorithm" if EMBEDDED
---help---
This option enables a TX rate control algorithm for
mac80211 that uses a PID controller to select the TX
rate.
config MAC80211_RC_MINSTREL
bool "Minstrel" if EMBEDDED
default y
---help---
This option enables the 'minstrel' TX rate control algorithm
choice
prompt "Default rate control algorithm"
default MAC80211_RC_DEFAULT_MINSTREL
---help---
This option selects the default rate control algorithm
mac80211 will use. Note that this default can still be
overridden through the ieee80211_default_rc_algo module
parameter if different algorithms are available.
config MAC80211_RC_DEFAULT_PID
bool "PID controller based rate control algorithm"
depends on MAC80211_RC_PID
---help---
Select the PID controller based rate control as the
default rate control algorithm. You should choose
this unless you know what you are doing.
config MAC80211_RC_DEFAULT_MINSTREL
bool "Minstrel"
depends on MAC80211_RC_MINSTREL
---help---
Select Minstrel as the default rate control algorithm.
endchoice
config MAC80211_RC_DEFAULT
string
default "minstrel" if MAC80211_RC_DEFAULT_MINSTREL
default "pid" if MAC80211_RC_DEFAULT_PID
default ""
endmenu
config MAC80211_MESH
bool "Enable mac80211 mesh networking (pre-802.11s) support"
depends on MAC80211 && EXPERIMENTAL
---help---
This options enables support of Draft 802.11s mesh networking.
The implementation is based on Draft 1.08 of the Mesh Networking
amendment. For more information visit http://o11s.org/.
config MAC80211_LEDS
bool "Enable LED triggers"
depends on MAC80211
select NEW_LEDS
select LEDS_TRIGGERS
---help---
This option enables a few LED triggers for different
packet receive/transmit events.
config MAC80211_DEBUGFS
bool "Export mac80211 internals in DebugFS"
depends on MAC80211 && DEBUG_FS
---help---
Select this to see extensive information about
the internal state of mac80211 in debugfs.
Say N unless you know you need this.
menuconfig MAC80211_DEBUG_MENU
bool "Select mac80211 debugging features"
depends on MAC80211
---help---
This option collects various mac80211 debug settings.
config MAC80211_DEBUG_PACKET_ALIGNMENT
bool "Enable packet alignment debugging"
depends on MAC80211_DEBUG_MENU
---help---
This option is recommended for driver authors and strongly
discouraged for everybody else, it will trigger a warning
when a driver hands mac80211 a buffer that is aligned in
a way that will cause problems with the IP stack on some
architectures.
Say N unless you're writing a mac80211 based driver.
config MAC80211_NOINLINE
bool "Do not inline TX/RX handlers"
depends on MAC80211_DEBUG_MENU
---help---
This option affects code generation in mac80211, when
selected some functions are marked "noinline" to allow
easier debugging of problems in the transmit and receive
paths.
This option increases code size a bit and inserts a lot
of function calls in the code, but is otherwise safe to
enable.
If unsure, say N unless you expect to be finding problems
in mac80211.
config MAC80211_VERBOSE_DEBUG
bool "Verbose debugging output"
depends on MAC80211_DEBUG_MENU
---help---
Selecting this option causes mac80211 to print out
many debugging messages. It should not be selected
on production systems as some of the messages are
remotely triggerable.
Do not select this option.
config MAC80211_HT_DEBUG
bool "Verbose HT debugging"
depends on MAC80211_DEBUG_MENU
---help---
This option enables 802.11n High Throughput features
debug tracing output.
It should not be selected on production systems as some
of the messages are remotely triggerable.
Do not select this option.
config MAC80211_TKIP_DEBUG
bool "Verbose TKIP debugging"
depends on MAC80211_DEBUG_MENU
---help---
Selecting this option causes mac80211 to print out
very verbose TKIP debugging messages. It should not
be selected on production systems as those messages
are remotely triggerable.
Do not select this option.
config MAC80211_IBSS_DEBUG
bool "Verbose IBSS debugging"
depends on MAC80211_DEBUG_MENU
---help---
Selecting this option causes mac80211 to print out
very verbose IBSS debugging messages. It should not
be selected on production systems as those messages
are remotely triggerable.
Do not select this option.
config MAC80211_VERBOSE_PS_DEBUG
bool "Verbose powersave mode debugging"
depends on MAC80211_DEBUG_MENU
---help---
Selecting this option causes mac80211 to print out very
verbose power save mode debugging messages (when mac80211
is an AP and has power saving stations.)
It should not be selected on production systems as those
messages are remotely triggerable.
Do not select this option.
config MAC80211_VERBOSE_MPL_DEBUG
bool "Verbose mesh peer link debugging"
depends on MAC80211_DEBUG_MENU
depends on MAC80211_MESH
---help---
Selecting this option causes mac80211 to print out very
verbose mesh peer link debugging messages (when mac80211
is taking part in a mesh network).
It should not be selected on production systems as those
messages are remotely triggerable.
Do not select this option.
config MAC80211_DEBUG_COUNTERS
bool "Extra statistics for TX/RX debugging"
depends on MAC80211_DEBUG_MENU
depends on MAC80211_DEBUGFS
---help---
Selecting this option causes mac80211 to keep additional
and very verbose statistics about TX and RX handler use
and show them in debugfs.
If unsure, say N.
|
