Linux-2.6.12-rc2

Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!

1 files changed, 704 insertions, 0 deletions

diff --git a/drivers/net/hamradio/baycom_ser_fdx.c b/drivers/net/hamradio/baycom_ser_fdx.c
new file mode 100644
index 0000000..25f270b
--- /dev/null
+++ b/drivers/net/hamradio/baycom_ser_fdx.c
@@ -0,0 +1,704 @@
+/*****************************************************************************/
+
+/*
+ *	baycom_ser_fdx.c  -- baycom ser12 fullduplex radio modem driver.
+ *
+ *	Copyright (C) 1996-2000  Thomas Sailer (sailer@ife.ee.ethz.ch)
+ *
+ *	This program is free software; you can redistribute it and/or modify
+ *	it under the terms of the GNU General Public License as published by
+ *	the Free Software Foundation; either version 2 of the License, or
+ *	(at your option) any later version.
+ *
+ *	This program is distributed in the hope that it will be useful,
+ *	but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *	MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *	GNU General Public License for more details.
+ *
+ *	You should have received a copy of the GNU General Public License
+ *	along with this program; if not, write to the Free Software
+ *	Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+ *
+ *  Please note that the GPL allows you to use the driver, NOT the radio.
+ *  In order to use the radio, you need a license from the communications
+ *  authority of your country.
+ *
+ *
+ *  Supported modems
+ *
+ *  ser12:  This is a very simple 1200 baud AFSK modem. The modem consists only
+ *          of a modulator/demodulator chip, usually a TI TCM3105. The computer
+ *          is responsible for regenerating the receiver bit clock, as well as
+ *          for handling the HDLC protocol. The modem connects to a serial port,
+ *          hence the name. Since the serial port is not used as an async serial
+ *          port, the kernel driver for serial ports cannot be used, and this
+ *          driver only supports standard serial hardware (8250, 16450, 16550A)
+ *
+ *          This modem usually draws its supply current out of the otherwise unused
+ *          TXD pin of the serial port. Thus a contignuous stream of 0x00-bytes
+ *          is transmitted to achieve a positive supply voltage.
+ *
+ *  hsk:    This is a 4800 baud FSK modem, designed for TNC use. It works fine
+ *          in 'baycom-mode' :-)  In contrast to the TCM3105 modem, power is
+ *          externally supplied. So there's no need to provide the 0x00-byte-stream
+ *          when receiving or idle, which drastically reduces interrupt load.
+ *
+ *  Command line options (insmod command line)
+ *
+ *  mode     ser#    hardware DCD
+ *           ser#*   software DCD
+ *           ser#+   hardware DCD, inverted signal at DCD pin
+ *           '#' denotes the baud rate / 100, eg. ser12* is '1200 baud, soft DCD'
+ *  iobase   base address of the port; common values are 0x3f8, 0x2f8, 0x3e8, 0x2e8
+ *  baud     baud rate (between 300 and 4800)
+ *  irq      interrupt line of the port; common values are 4,3
+ *
+ *
+ *  History:
+ *   0.1  26.06.1996  Adapted from baycom.c and made network driver interface
+ *        18.10.1996  Changed to new user space access routines (copy_{to,from}_user)
+ *   0.3  26.04.1997  init code/data tagged
+ *   0.4  08.07.1997  alternative ser12 decoding algorithm (uses delta CTS ints)
+ *   0.5  11.11.1997  ser12/par96 split into separate files
+ *   0.6  24.01.1998  Thorsten Kranzkowski, dl8bcu and Thomas Sailer:
+ *                    reduced interrupt load in transmit case
+ *                    reworked receiver
+ *   0.7  03.08.1999  adapt to Linus' new __setup/__initcall
+ *   0.8  10.08.1999  use module_init/module_exit
+ *   0.9  12.02.2000  adapted to softnet driver interface
+ *   0.10 03.07.2000  fix interface name handling
+ */
+
+/*****************************************************************************/
+
+#include <linux/module.h>
+#include <linux/ioport.h>
+#include <linux/string.h>
+#include <linux/init.h>
+#include <asm/uaccess.h>
+#include <asm/io.h>
+#include <linux/hdlcdrv.h>
+#include <linux/baycom.h>
+
+/* --------------------------------------------------------------------- */
+
+#define BAYCOM_DEBUG
+
+/* --------------------------------------------------------------------- */
+
+static const char bc_drvname[] = "baycom_ser_fdx";
+static const char bc_drvinfo[] = KERN_INFO "baycom_ser_fdx: (C) 1996-2000 Thomas Sailer, HB9JNX/AE4WA\n"
+KERN_INFO "baycom_ser_fdx: version 0.10 compiled " __TIME__ " " __DATE__ "\n";
+
+/* --------------------------------------------------------------------- */
+
+#define NR_PORTS 4
+
+static struct net_device *baycom_device[NR_PORTS];
+
+/* --------------------------------------------------------------------- */
+
+#define RBR(iobase) (iobase+0)
+#define THR(iobase) (iobase+0)
+#define IER(iobase) (iobase+1)
+#define IIR(iobase) (iobase+2)
+#define FCR(iobase) (iobase+2)
+#define LCR(iobase) (iobase+3)
+#define MCR(iobase) (iobase+4)
+#define LSR(iobase) (iobase+5)
+#define MSR(iobase) (iobase+6)
+#define SCR(iobase) (iobase+7)
+#define DLL(iobase) (iobase+0)
+#define DLM(iobase) (iobase+1)
+
+#define SER12_EXTENT 8
+
+/* ---------------------------------------------------------------------- */
+/*
+ * Information that need to be kept for each board.
+ */
+
+struct baycom_state {
+	struct hdlcdrv_state hdrv;
+
+	unsigned int baud, baud_us, baud_arbdiv, baud_uartdiv, baud_dcdtimeout;
+	int opt_dcd;
+
+	struct modem_state {
+		unsigned char flags;
+		unsigned char ptt;
+		unsigned int shreg;
+		struct modem_state_ser12 {
+			unsigned char tx_bit;
+			unsigned char last_rxbit;
+			int dcd_sum0, dcd_sum1, dcd_sum2;
+			int dcd_time;
+			unsigned int pll_time;
+			unsigned int txshreg;
+		} ser12;
+	} modem;
+
+#ifdef BAYCOM_DEBUG
+	struct debug_vals {
+		unsigned long last_jiffies;
+		unsigned cur_intcnt;
+		unsigned last_intcnt;
+		int cur_pllcorr;
+		int last_pllcorr;
+	} debug_vals;
+#endif /* BAYCOM_DEBUG */
+};
+
+/* --------------------------------------------------------------------- */
+
+static inline void baycom_int_freq(struct baycom_state *bc)
+{
+#ifdef BAYCOM_DEBUG
+	unsigned long cur_jiffies = jiffies;
+	/*
+	 * measure the interrupt frequency
+	 */
+	bc->debug_vals.cur_intcnt++;
+	if ((cur_jiffies - bc->debug_vals.last_jiffies) >= HZ) {
+		bc->debug_vals.last_jiffies = cur_jiffies;
+		bc->debug_vals.last_intcnt = bc->debug_vals.cur_intcnt;
+		bc->debug_vals.cur_intcnt = 0;
+		bc->debug_vals.last_pllcorr = bc->debug_vals.cur_pllcorr;
+		bc->debug_vals.cur_pllcorr = 0;
+	}
+#endif /* BAYCOM_DEBUG */
+}
+
+/* --------------------------------------------------------------------- */
+/*
+ * ===================== SER12 specific routines =========================
+ */
+
+/* --------------------------------------------------------------------- */
+
+static inline void ser12_set_divisor(struct net_device *dev,
+                                     unsigned int divisor)
+{
+        outb(0x81, LCR(dev->base_addr));        /* DLAB = 1 */
+        outb(divisor, DLL(dev->base_addr));
+        outb(divisor >> 8, DLM(dev->base_addr));
+        outb(0x01, LCR(dev->base_addr));        /* word length = 6 */
+        /*
+         * make sure the next interrupt is generated;
+         * 0 must be used to power the modem; the modem draws its
+         * power from the TxD line
+         */
+        outb(0x00, THR(dev->base_addr));
+        /*
+         * it is important not to set the divider while transmitting;
+         * this reportedly makes some UARTs generating interrupts
+         * in the hundredthousands per second region
+         * Reported by: Ignacio.Arenaza@studi.epfl.ch (Ignacio Arenaza Nuno)
+         */
+}
+
+/* --------------------------------------------------------------------- */
+
+#if 0
+static inline unsigned int hweight16(unsigned int w)
+        __attribute__ ((unused));
+static inline unsigned int hweight8(unsigned int w)
+        __attribute__ ((unused));
+
+static inline unsigned int hweight16(unsigned int w)
+{
+        unsigned short res = (w & 0x5555) + ((w >> 1) & 0x5555);
+        res = (res & 0x3333) + ((res >> 2) & 0x3333);
+        res = (res & 0x0F0F) + ((res >> 4) & 0x0F0F);
+        return (res & 0x00FF) + ((res >> 8) & 0x00FF);
+}
+
+static inline unsigned int hweight8(unsigned int w)
+{
+        unsigned short res = (w & 0x55) + ((w >> 1) & 0x55);
+        res = (res & 0x33) + ((res >> 2) & 0x33);
+        return (res & 0x0F) + ((res >> 4) & 0x0F);
+}
+#endif
+
+/* --------------------------------------------------------------------- */
+
+static __inline__ void ser12_rx(struct net_device *dev, struct baycom_state *bc, struct timeval *tv, unsigned char curs)
+{
+	int timediff;
+	int bdus8 = bc->baud_us >> 3;
+	int bdus4 = bc->baud_us >> 2;
+	int bdus2 = bc->baud_us >> 1;
+
+	timediff = 1000000 + tv->tv_usec - bc->modem.ser12.pll_time;
+	while (timediff >= 500000)
+		timediff -= 1000000;
+	while (timediff >= bdus2) {
+		timediff -= bc->baud_us;
+		bc->modem.ser12.pll_time += bc->baud_us;
+		bc->modem.ser12.dcd_time--;
+		/* first check if there is room to add a bit */
+		if (bc->modem.shreg & 1) {
+			hdlcdrv_putbits(&bc->hdrv, (bc->modem.shreg >> 1) ^ 0xffff);
+			bc->modem.shreg = 0x10000;
+		}
+		/* add a one bit */
+		bc->modem.shreg >>= 1;
+	}
+	if (bc->modem.ser12.dcd_time <= 0) {
+		if (!bc->opt_dcd)
+			hdlcdrv_setdcd(&bc->hdrv, (bc->modem.ser12.dcd_sum0 + 
+						   bc->modem.ser12.dcd_sum1 + 
+						   bc->modem.ser12.dcd_sum2) < 0);
+		bc->modem.ser12.dcd_sum2 = bc->modem.ser12.dcd_sum1;
+		bc->modem.ser12.dcd_sum1 = bc->modem.ser12.dcd_sum0;
+		bc->modem.ser12.dcd_sum0 = 2; /* slight bias */
+		bc->modem.ser12.dcd_time += 120;
+	}
+	if (bc->modem.ser12.last_rxbit != curs) {
+		bc->modem.ser12.last_rxbit = curs;
+		bc->modem.shreg |= 0x10000;
+		/* adjust the PLL */
+		if (timediff > 0)
+			bc->modem.ser12.pll_time += bdus8;
+		else
+			bc->modem.ser12.pll_time += 1000000 - bdus8;
+		/* update DCD */
+		if (abs(timediff) > bdus4)
+			bc->modem.ser12.dcd_sum0 += 4;
+		else
+			bc->modem.ser12.dcd_sum0--;
+#ifdef BAYCOM_DEBUG
+		bc->debug_vals.cur_pllcorr = timediff;
+#endif /* BAYCOM_DEBUG */
+	}
+	while (bc->modem.ser12.pll_time >= 1000000)
+		bc->modem.ser12.pll_time -= 1000000;
+}
+
+/* --------------------------------------------------------------------- */
+
+static irqreturn_t ser12_interrupt(int irq, void *dev_id, struct pt_regs *regs)
+{
+	struct net_device *dev = (struct net_device *)dev_id;
+	struct baycom_state *bc = netdev_priv(dev);
+	struct timeval tv;
+	unsigned char iir, msr;
+	unsigned int txcount = 0;
+
+	if (!bc || bc->hdrv.magic != HDLCDRV_MAGIC)
+		return IRQ_NONE;
+	/* fast way out for shared irq */
+	if ((iir = inb(IIR(dev->base_addr))) & 1) 	
+		return IRQ_NONE;
+	/* get current time */
+	do_gettimeofday(&tv);
+	msr = inb(MSR(dev->base_addr));
+	/* delta DCD */
+	if ((msr & 8) && bc->opt_dcd)
+		hdlcdrv_setdcd(&bc->hdrv, !((msr ^ bc->opt_dcd) & 0x80));
+	do {
+		switch (iir & 6) {
+		case 6:
+			inb(LSR(dev->base_addr));
+			break;
+			
+		case 4:
+			inb(RBR(dev->base_addr));
+			break;
+			
+		case 2:
+			/*
+			 * make sure the next interrupt is generated;
+			 * 0 must be used to power the modem; the modem draws its
+			 * power from the TxD line
+			 */
+			outb(0x00, THR(dev->base_addr));
+			baycom_int_freq(bc);
+			txcount++;
+			/*
+			 * first output the last bit (!) then call HDLC transmitter,
+			 * since this may take quite long
+			 */
+			if (bc->modem.ptt)
+				outb(0x0e | (!!bc->modem.ser12.tx_bit), MCR(dev->base_addr));
+			else
+				outb(0x0d, MCR(dev->base_addr));       /* transmitter off */
+			break;
+			
+		default:
+			msr = inb(MSR(dev->base_addr));
+			/* delta DCD */
+			if ((msr & 8) && bc->opt_dcd) 
+				hdlcdrv_setdcd(&bc->hdrv, !((msr ^ bc->opt_dcd) & 0x80));
+			break;
+		}
+		iir = inb(IIR(dev->base_addr));
+	} while (!(iir & 1));
+	ser12_rx(dev, bc, &tv, msr & 0x10); /* CTS */
+	if (bc->modem.ptt && txcount) {
+		if (bc->modem.ser12.txshreg <= 1) {
+			bc->modem.ser12.txshreg = 0x10000 | hdlcdrv_getbits(&bc->hdrv);
+			if (!hdlcdrv_ptt(&bc->hdrv)) {
+				ser12_set_divisor(dev, 115200/100/8);
+				bc->modem.ptt = 0;
+				goto end_transmit;
+			}
+		}
+		bc->modem.ser12.tx_bit = !(bc->modem.ser12.tx_bit ^ (bc->modem.ser12.txshreg & 1));
+		bc->modem.ser12.txshreg >>= 1;
+	}
+ end_transmit:
+	local_irq_enable();
+	if (!bc->modem.ptt && txcount) {
+		hdlcdrv_arbitrate(dev, &bc->hdrv);
+		if (hdlcdrv_ptt(&bc->hdrv)) {
+			ser12_set_divisor(dev, bc->baud_uartdiv);
+			bc->modem.ser12.txshreg = 1;
+			bc->modem.ptt = 1;
+		}
+	}
+	hdlcdrv_transmitter(dev, &bc->hdrv);
+	hdlcdrv_receiver(dev, &bc->hdrv);
+	local_irq_disable();
+	return IRQ_HANDLED;
+}
+
+/* --------------------------------------------------------------------- */
+
+enum uart { c_uart_unknown, c_uart_8250,
+	    c_uart_16450, c_uart_16550, c_uart_16550A};
+static const char *uart_str[] = { 
+	"unknown", "8250", "16450", "16550", "16550A" 
+};
+
+static enum uart ser12_check_uart(unsigned int iobase)
+{
+	unsigned char b1,b2,b3;
+	enum uart u;
+	enum uart uart_tab[] =
+		{ c_uart_16450, c_uart_unknown, c_uart_16550, c_uart_16550A };
+
+	b1 = inb(MCR(iobase));
+	outb(b1 | 0x10, MCR(iobase));	/* loopback mode */
+	b2 = inb(MSR(iobase));
+	outb(0x1a, MCR(iobase));
+	b3 = inb(MSR(iobase)) & 0xf0;
+	outb(b1, MCR(iobase));			/* restore old values */
+	outb(b2, MSR(iobase));
+	if (b3 != 0x90)
+		return c_uart_unknown;
+	inb(RBR(iobase));
+	inb(RBR(iobase));
+	outb(0x01, FCR(iobase));		/* enable FIFOs */
+	u = uart_tab[(inb(IIR(iobase)) >> 6) & 3];
+	if (u == c_uart_16450) {
+		outb(0x5a, SCR(iobase));
+		b1 = inb(SCR(iobase));
+		outb(0xa5, SCR(iobase));
+		b2 = inb(SCR(iobase));
+		if ((b1 != 0x5a) || (b2 != 0xa5))
+			u = c_uart_8250;
+	}
+	return u;
+}
+
+/* --------------------------------------------------------------------- */
+
+static int ser12_open(struct net_device *dev)
+{
+	struct baycom_state *bc = netdev_priv(dev);
+	enum uart u;
+
+	if (!dev || !bc)
+		return -ENXIO;
+	if (!dev->base_addr || dev->base_addr > 0x1000-SER12_EXTENT ||
+	    dev->irq < 2 || dev->irq > 15)
+		return -ENXIO;
+	if (bc->baud < 300 || bc->baud > 4800)
+		return -EINVAL;
+	if (!request_region(dev->base_addr, SER12_EXTENT, "baycom_ser_fdx")) {
+		printk(KERN_WARNING "BAYCOM_SER_FSX: I/O port 0x%04lx busy \n", 
+		       dev->base_addr);
+		return -EACCES;
+	}
+	memset(&bc->modem, 0, sizeof(bc->modem));
+	bc->hdrv.par.bitrate = bc->baud;
+	bc->baud_us = 1000000/bc->baud;
+	bc->baud_uartdiv = (115200/8)/bc->baud;
+	if ((u = ser12_check_uart(dev->base_addr)) == c_uart_unknown){
+		release_region(dev->base_addr, SER12_EXTENT);
+		return -EIO;
+	}
+	outb(0, FCR(dev->base_addr));  /* disable FIFOs */
+	outb(0x0d, MCR(dev->base_addr));
+	outb(0, IER(dev->base_addr));
+	if (request_irq(dev->irq, ser12_interrupt, SA_INTERRUPT | SA_SHIRQ,
+			"baycom_ser_fdx", dev)) {
+		release_region(dev->base_addr, SER12_EXTENT);
+		return -EBUSY;
+	}
+	/*
+	 * set the SIO to 6 Bits/character; during receive,
+	 * the baud rate is set to produce 100 ints/sec
+	 * to feed the channel arbitration process,
+	 * during transmit to baud ints/sec to run
+	 * the transmitter
+	 */
+	ser12_set_divisor(dev, 115200/100/8);
+	/*
+	 * enable transmitter empty interrupt and modem status interrupt
+	 */
+	outb(0x0a, IER(dev->base_addr));
+	/*
+	 * make sure the next interrupt is generated;
+	 * 0 must be used to power the modem; the modem draws its
+	 * power from the TxD line
+	 */
+	outb(0x00, THR(dev->base_addr));
+	hdlcdrv_setdcd(&bc->hdrv, 0);
+	printk(KERN_INFO "%s: ser_fdx at iobase 0x%lx irq %u baud %u uart %s\n",
+	       bc_drvname, dev->base_addr, dev->irq, bc->baud, uart_str[u]);
+	return 0;
+}
+
+/* --------------------------------------------------------------------- */
+
+static int ser12_close(struct net_device *dev)
+{
+	struct baycom_state *bc = netdev_priv(dev);
+
+	if (!dev || !bc)
+		return -EINVAL;
+	/*
+	 * disable interrupts
+	 */
+	outb(0, IER(dev->base_addr));
+	outb(1, MCR(dev->base_addr));
+	free_irq(dev->irq, dev);
+	release_region(dev->base_addr, SER12_EXTENT);
+	printk(KERN_INFO "%s: close ser_fdx at iobase 0x%lx irq %u\n",
+	       bc_drvname, dev->base_addr, dev->irq);
+	return 0;
+}
+
+/* --------------------------------------------------------------------- */
+/*
+ * ===================== hdlcdrv driver interface =========================
+ */
+
+/* --------------------------------------------------------------------- */
+
+static int baycom_ioctl(struct net_device *dev, struct ifreq *ifr,
+			struct hdlcdrv_ioctl *hi, int cmd);
+
+/* --------------------------------------------------------------------- */
+
+static struct hdlcdrv_ops ser12_ops = {
+	.drvname = bc_drvname,
+	.drvinfo = bc_drvinfo,
+	.open    = ser12_open,
+	.close   = ser12_close,
+	.ioctl   = baycom_ioctl,
+};
+
+/* --------------------------------------------------------------------- */
+
+static int baycom_setmode(struct baycom_state *bc, const char *modestr)
+{
+	unsigned int baud;
+
+	if (!strncmp(modestr, "ser", 3)) {
+		baud = simple_strtoul(modestr+3, NULL, 10);
+		if (baud >= 3 && baud <= 48)
+			bc->baud = baud*100;
+	}
+	if (strchr(modestr, '*'))
+		bc->opt_dcd = 0;
+	else if (strchr(modestr, '+'))
+		bc->opt_dcd = -1;
+	else
+		bc->opt_dcd = 1;
+	return 0;
+}
+
+/* --------------------------------------------------------------------- */
+
+static int baycom_ioctl(struct net_device *dev, struct ifreq *ifr,
+			struct hdlcdrv_ioctl *hi, int cmd)
+{
+	struct baycom_state *bc;
+	struct baycom_ioctl bi;
+
+	if (!dev)
+		return -EINVAL;
+
+	bc = netdev_priv(dev);
+	BUG_ON(bc->hdrv.magic != HDLCDRV_MAGIC);
+
+	if (cmd != SIOCDEVPRIVATE)
+		return -ENOIOCTLCMD;
+	switch (hi->cmd) {
+	default:
+		break;
+
+	case HDLCDRVCTL_GETMODE:
+		sprintf(hi->data.modename, "ser%u", bc->baud / 100);
+		if (bc->opt_dcd <= 0)
+			strcat(hi->data.modename, (!bc->opt_dcd) ? "*" : "+");
+		if (copy_to_user(ifr->ifr_data, hi, sizeof(struct hdlcdrv_ioctl)))
+			return -EFAULT;
+		return 0;
+
+	case HDLCDRVCTL_SETMODE:
+		if (netif_running(dev) || !capable(CAP_NET_ADMIN))
+			return -EACCES;
+		hi->data.modename[sizeof(hi->data.modename)-1] = '\0';
+		return baycom_setmode(bc, hi->data.modename);
+
+	case HDLCDRVCTL_MODELIST:
+		strcpy(hi->data.modename, "ser12,ser3,ser24");
+		if (copy_to_user(ifr->ifr_data, hi, sizeof(struct hdlcdrv_ioctl)))
+			return -EFAULT;
+		return 0;
+
+	case HDLCDRVCTL_MODEMPARMASK:
+		return HDLCDRV_PARMASK_IOBASE | HDLCDRV_PARMASK_IRQ;
+
+	}
+
+	if (copy_from_user(&bi, ifr->ifr_data, sizeof(bi)))
+		return -EFAULT;
+	switch (bi.cmd) {
+	default:
+		return -ENOIOCTLCMD;
+
+#ifdef BAYCOM_DEBUG
+	case BAYCOMCTL_GETDEBUG:
+		bi.data.dbg.debug1 = bc->hdrv.ptt_keyed;
+		bi.data.dbg.debug2 = bc->debug_vals.last_intcnt;
+		bi.data.dbg.debug3 = bc->debug_vals.last_pllcorr;
+		break;
+#endif /* BAYCOM_DEBUG */
+
+	}
+	if (copy_to_user(ifr->ifr_data, &bi, sizeof(bi)))
+		return -EFAULT;
+	return 0;
+
+}
+
+/* --------------------------------------------------------------------- */
+
+/*
+ * command line settable parameters
+ */
+static char *mode[NR_PORTS] = { "ser12*", };
+static int iobase[NR_PORTS] = { 0x3f8, };
+static int irq[NR_PORTS] = { 4, };
+static int baud[NR_PORTS] = { [0 ... NR_PORTS-1] = 1200 };
+
+module_param_array(mode, charp, NULL, 0);
+MODULE_PARM_DESC(mode, "baycom operating mode; * for software DCD");
+module_param_array(iobase, int, NULL, 0);
+MODULE_PARM_DESC(iobase, "baycom io base address");
+module_param_array(irq, int, NULL, 0);
+MODULE_PARM_DESC(irq, "baycom irq number");
+module_param_array(baud, int, NULL, 0);
+MODULE_PARM_DESC(baud, "baycom baud rate (300 to 4800)");
+
+MODULE_AUTHOR("Thomas M. Sailer, sailer@ife.ee.ethz.ch, hb9jnx@hb9w.che.eu");
+MODULE_DESCRIPTION("Baycom ser12 full duplex amateur radio modem driver");
+MODULE_LICENSE("GPL");
+
+/* --------------------------------------------------------------------- */
+
+static int __init init_baycomserfdx(void)
+{
+	int i, found = 0;
+	char set_hw = 1;
+
+	printk(bc_drvinfo);
+	/*
+	 * register net devices
+	 */
+	for (i = 0; i < NR_PORTS; i++) {
+		struct net_device *dev;
+		struct baycom_state *bc;
+		char ifname[IFNAMSIZ];
+
+		sprintf(ifname, "bcsf%d", i);
+
+		if (!mode[i])
+			set_hw = 0;
+		if (!set_hw)
+			iobase[i] = irq[i] = 0;
+
+		dev = hdlcdrv_register(&ser12_ops, 
+				       sizeof(struct baycom_state),
+				       ifname, iobase[i], irq[i], 0);
+		if (IS_ERR(dev)) 
+			break;
+
+		bc = netdev_priv(dev);
+		if (set_hw && baycom_setmode(bc, mode[i]))
+			set_hw = 0;
+		bc->baud = baud[i];
+		found++;
+		baycom_device[i] = dev;
+	}
+
+	if (!found)
+		return -ENXIO;
+	return 0;
+}
+
+static void __exit cleanup_baycomserfdx(void)
+{
+	int i;
+
+	for(i = 0; i < NR_PORTS; i++) {
+		struct net_device *dev = baycom_device[i];
+		if (dev) 
+			hdlcdrv_unregister(dev);
+	}
+}
+
+module_init(init_baycomserfdx);
+module_exit(cleanup_baycomserfdx);
+
+/* --------------------------------------------------------------------- */
+
+#ifndef MODULE
+
+/*
+ * format: baycom_ser_fdx=io,irq,mode
+ * mode: ser#    hardware DCD
+ *       ser#*   software DCD
+ *       ser#+   hardware DCD, inverted signal at DCD pin
+ * '#' denotes the baud rate / 100, eg. ser12* is '1200 baud, soft DCD'
+ */
+
+static int __init baycom_ser_fdx_setup(char *str)
+{
+        static unsigned nr_dev;
+        int ints[4];
+
+        if (nr_dev >= NR_PORTS)
+                return 0;
+        str = get_options(str, 4, ints);
+        if (ints[0] < 2)
+                return 0;
+        mode[nr_dev] = str;
+        iobase[nr_dev] = ints[1];
+        irq[nr_dev] = ints[2];
+	if (ints[0] >= 3)
+		baud[nr_dev] = ints[3];
+	nr_dev++;
+	return 1;
+}
+
+__setup("baycom_ser_fdx=", baycom_ser_fdx_setup);
+
+#endif /* MODULE */
+/* --------------------------------------------------------------------- */