diff options
| -rw-r--r-- | MAINTAINERS | 10 | ||||
| -rw-r--r-- | drivers/input/touchscreen/Kconfig | 14 | ||||
| -rw-r--r-- | drivers/input/touchscreen/Makefile | 3 | ||||
| -rw-r--r-- | drivers/input/touchscreen/wm97xx-core.c | 789 | ||||
| -rw-r--r-- | include/linux/wm97xx.h | 311 |
5 files changed, 1127 insertions, 0 deletions
diff --git a/MAINTAINERS b/MAINTAINERS index 90dcbbc..87bdced 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -4343,6 +4343,16 @@ L: linux-wireless@vger.kernel.org W: http://oops.ghostprotocols.net:81/blog S: Maintained +WM97XX TOUCHSCREEN DRIVERS +P: Mark Brown +M: broonie@opensource.wolfsonmicro.com +P: Liam Girdwood +M: liam.girdwood@wolfsonmicro.com +L: linux-input@vger.kernel.org +T: git git://opensource.wolfsonmicro.com/linux-2.6-touch +W: http://opensource.wolfsonmicro.com/node/7 +S: Supported + X.25 NETWORK LAYER P: Henner Eisen M: eis@baty.hanse.de diff --git a/drivers/input/touchscreen/Kconfig b/drivers/input/touchscreen/Kconfig index 90e8e92..a95a87c 100644 --- a/drivers/input/touchscreen/Kconfig +++ b/drivers/input/touchscreen/Kconfig @@ -185,6 +185,20 @@ config TOUCHSCREEN_UCB1400 To compile this driver as a module, choose M here: the module will be called ucb1400_ts. +config TOUCHSCREEN_WM97XX + tristate "Support for WM97xx AC97 touchscreen controllers" + depends on AC97_BUS + help + Say Y here if you have a Wolfson Microelectronics WM97xx + touchscreen connected to your system. Note that this option + only enables core driver, you will also need to select + support for appropriate chip below. + + If unsure, say N. + + To compile this driver as a module, choose M here: the + module will be called wm97xx-ts. + config TOUCHSCREEN_USB_COMPOSITE tristate "USB Touchscreen Driver" depends on USB_ARCH_HAS_HCD diff --git a/drivers/input/touchscreen/Makefile b/drivers/input/touchscreen/Makefile index 35d4097..b4e7b5d 100644 --- a/drivers/input/touchscreen/Makefile +++ b/drivers/input/touchscreen/Makefile @@ -4,6 +4,8 @@ # Each configuration option enables a list of files. +wm97xx-ts-y := wm97xx-core.o + obj-$(CONFIG_TOUCHSCREEN_ADS7846) += ads7846.o obj-$(CONFIG_TOUCHSCREEN_BITSY) += h3600_ts_input.o obj-$(CONFIG_TOUCHSCREEN_CORGI) += corgi_ts.o @@ -19,3 +21,4 @@ obj-$(CONFIG_TOUCHSCREEN_PENMOUNT) += penmount.o obj-$(CONFIG_TOUCHSCREEN_TOUCHRIGHT) += touchright.o obj-$(CONFIG_TOUCHSCREEN_TOUCHWIN) += touchwin.o obj-$(CONFIG_TOUCHSCREEN_UCB1400) += ucb1400_ts.o +obj-$(CONFIG_TOUCHSCREEN_WM97XX) += wm97xx-ts.o diff --git a/drivers/input/touchscreen/wm97xx-core.c b/drivers/input/touchscreen/wm97xx-core.c new file mode 100644 index 0000000..2910999 --- /dev/null +++ b/drivers/input/touchscreen/wm97xx-core.c @@ -0,0 +1,789 @@ +/* + * wm97xx-core.c -- Touch screen driver core for Wolfson WM9705, WM9712 + * and WM9713 AC97 Codecs. + * + * Copyright 2003, 2004, 2005, 2006, 2007, 2008 Wolfson Microelectronics PLC. + * Author: Liam Girdwood + * liam.girdwood@wolfsonmicro.com or linux@wolfsonmicro.com + * Parts Copyright : Ian Molton <spyro@f2s.com> + * Andrew Zabolotny <zap@homelink.ru> + * Russell King <rmk@arm.linux.org.uk> + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. + * + * Notes: + * + * Features: + * - supports WM9705, WM9712, WM9713 + * - polling mode + * - continuous mode (arch-dependent) + * - adjustable rpu/dpp settings + * - adjustable pressure current + * - adjustable sample settle delay + * - 4 and 5 wire touchscreens (5 wire is WM9712 only) + * - pen down detection + * - battery monitor + * - sample AUX adcs + * - power management + * - codec GPIO + * - codec event notification + * Todo + * - Support for async sampling control for noisy LCDs. + * + */ + +#include <linux/module.h> +#include <linux/moduleparam.h> +#include <linux/version.h> +#include <linux/kernel.h> +#include <linux/init.h> +#include <linux/delay.h> +#include <linux/string.h> +#include <linux/proc_fs.h> +#include <linux/pm.h> +#include <linux/interrupt.h> +#include <linux/bitops.h> +#include <linux/workqueue.h> +#include <linux/wm97xx.h> +#include <linux/uaccess.h> +#include <linux/io.h> + +#define TS_NAME "wm97xx" +#define WM_CORE_VERSION "1.00" +#define DEFAULT_PRESSURE 0xb0c0 + + +/* + * Touchscreen absolute values + * + * These parameters are used to help the input layer discard out of + * range readings and reduce jitter etc. + * + * o min, max:- indicate the min and max values your touch screen returns + * o fuzz:- use a higher number to reduce jitter + * + * The default values correspond to Mainstone II in QVGA mode + * + * Please read + * Documentation/input/input-programming.txt for more details. + */ + +static int abs_x[3] = {350, 3900, 5}; +module_param_array(abs_x, int, NULL, 0); +MODULE_PARM_DESC(abs_x, "Touchscreen absolute X min, max, fuzz"); + +static int abs_y[3] = {320, 3750, 40}; +module_param_array(abs_y, int, NULL, 0); +MODULE_PARM_DESC(abs_y, "Touchscreen absolute Y min, max, fuzz"); + +static int abs_p[3] = {0, 150, 4}; +module_param_array(abs_p, int, NULL, 0); +MODULE_PARM_DESC(abs_p, "Touchscreen absolute Pressure min, max, fuzz"); + +/* + * wm97xx IO access, all IO locking done by AC97 layer + */ +int wm97xx_reg_read(struct wm97xx *wm, u16 reg) +{ + if (wm->ac97) + return wm->ac97->bus->ops->read(wm->ac97, reg); + else + return -1; +} +EXPORT_SYMBOL_GPL(wm97xx_reg_read); + +void wm97xx_reg_write(struct wm97xx *wm, u16 reg, u16 val) +{ + /* cache digitiser registers */ + if (reg >= AC97_WM9713_DIG1 && reg <= AC97_WM9713_DIG3) + wm->dig[(reg - AC97_WM9713_DIG1) >> 1] = val; + + /* cache gpio regs */ + if (reg >= AC97_GPIO_CFG && reg <= AC97_MISC_AFE) + wm->gpio[(reg - AC97_GPIO_CFG) >> 1] = val; + + /* wm9713 irq reg */ + if (reg == 0x5a) + wm->misc = val; + + if (wm->ac97) + wm->ac97->bus->ops->write(wm->ac97, reg, val); +} +EXPORT_SYMBOL_GPL(wm97xx_reg_write); + +/** + * wm97xx_read_aux_adc - Read the aux adc. + * @wm: wm97xx device. + * @adcsel: codec ADC to be read + * + * Reads the selected AUX ADC. + */ + +int wm97xx_read_aux_adc(struct wm97xx *wm, u16 adcsel) +{ + int power_adc = 0, auxval; + u16 power = 0; + + /* get codec */ + mutex_lock(&wm->codec_mutex); + + /* When the touchscreen is not in use, we may have to power up + * the AUX ADC before we can use sample the AUX inputs-> + */ + if (wm->id == WM9713_ID2 && + (power = wm97xx_reg_read(wm, AC97_EXTENDED_MID)) & 0x8000) { + power_adc = 1; + wm97xx_reg_write(wm, AC97_EXTENDED_MID, power & 0x7fff); + } + + /* Prepare the codec for AUX reading */ + wm->codec->aux_prepare(wm); + + /* Turn polling mode on to read AUX ADC */ + wm->pen_probably_down = 1; + wm->codec->poll_sample(wm, adcsel, &auxval); + + if (power_adc) + wm97xx_reg_write(wm, AC97_EXTENDED_MID, power | 0x8000); + + wm->codec->dig_restore(wm); + + wm->pen_probably_down = 0; + + mutex_unlock(&wm->codec_mutex); + return auxval & 0xfff; +} +EXPORT_SYMBOL_GPL(wm97xx_read_aux_adc); + +/** + * wm97xx_get_gpio - Get the status of a codec GPIO. + * @wm: wm97xx device. + * @gpio: gpio + * + * Get the status of a codec GPIO pin + */ + +enum wm97xx_gpio_status wm97xx_get_gpio(struct wm97xx *wm, u32 gpio) +{ + u16 status; + enum wm97xx_gpio_status ret; + + mutex_lock(&wm->codec_mutex); + status = wm97xx_reg_read(wm, AC97_GPIO_STATUS); + + if (status & gpio) + ret = WM97XX_GPIO_HIGH; + else + ret = WM97XX_GPIO_LOW; + + mutex_unlock(&wm->codec_mutex); + return ret; +} +EXPORT_SYMBOL_GPL(wm97xx_get_gpio); + +/** + * wm97xx_set_gpio - Set the status of a codec GPIO. + * @wm: wm97xx device. + * @gpio: gpio + * + * + * Set the status of a codec GPIO pin + */ + +void wm97xx_set_gpio(struct wm97xx *wm, u32 gpio, + enum wm97xx_gpio_status status) +{ + u16 reg; + + mutex_lock(&wm->codec_mutex); + reg = wm97xx_reg_read(wm, AC97_GPIO_STATUS); + + if (status & WM97XX_GPIO_HIGH) + reg |= gpio; + else + reg &= ~gpio; + + if (wm->id == WM9712_ID2) + wm97xx_reg_write(wm, AC97_GPIO_STATUS, reg << 1); + else + wm97xx_reg_write(wm, AC97_GPIO_STATUS, reg); + mutex_unlock(&wm->codec_mutex); +} +EXPORT_SYMBOL_GPL(wm97xx_set_gpio); + +/* + * Codec GPIO pin configuration, this sets pin direction, polarity, + * stickyness and wake up. + */ +void wm97xx_config_gpio(struct wm97xx *wm, u32 gpio, enum wm97xx_gpio_dir dir, + enum wm97xx_gpio_pol pol, enum wm97xx_gpio_sticky sticky, + enum wm97xx_gpio_wake wake) +{ + u16 reg; + + mutex_lock(&wm->codec_mutex); + reg = wm97xx_reg_read(wm, AC97_GPIO_POLARITY); + + if (pol == WM97XX_GPIO_POL_HIGH) + reg |= gpio; + else + reg &= ~gpio; + + wm97xx_reg_write(wm, AC97_GPIO_POLARITY, reg); + reg = wm97xx_reg_read(wm, AC97_GPIO_STICKY); + + if (sticky == WM97XX_GPIO_STICKY) + reg |= gpio; + else + reg &= ~gpio; + + wm97xx_reg_write(wm, AC97_GPIO_STICKY, reg); + reg = wm97xx_reg_read(wm, AC97_GPIO_WAKEUP); + + if (wake == WM97XX_GPIO_WAKE) + reg |= gpio; + else + reg &= ~gpio; + + wm97xx_reg_write(wm, AC97_GPIO_WAKEUP, reg); + reg = wm97xx_reg_read(wm, AC97_GPIO_CFG); + + if (dir == WM97XX_GPIO_IN) + reg |= gpio; + else + reg &= ~gpio; + + wm97xx_reg_write(wm, AC97_GPIO_CFG, reg); + mutex_unlock(&wm->codec_mutex); +} +EXPORT_SYMBOL_GPL(wm97xx_config_gpio); + +/* + * Handle a pen down interrupt. + */ +static void wm97xx_pen_irq_worker(struct work_struct *work) +{ + struct wm97xx *wm = container_of(work, struct wm97xx, pen_event_work); + int pen_was_down = wm->pen_is_down; + + /* do we need to enable the touch panel reader */ + if (wm->id == WM9705_ID2) { + if (wm97xx_reg_read(wm, AC97_WM97XX_DIGITISER_RD) & + WM97XX_PEN_DOWN) + wm->pen_is_down = 1; + else + wm->pen_is_down = 0; + } else { + u16 status, pol; + mutex_lock(&wm->codec_mutex); + status = wm97xx_reg_read(wm, AC97_GPIO_STATUS); + pol = wm97xx_reg_read(wm, AC97_GPIO_POLARITY); + + if (WM97XX_GPIO_13 & pol & status) { + wm->pen_is_down = 1; + wm97xx_reg_write(wm, AC97_GPIO_POLARITY, pol & + ~WM97XX_GPIO_13); + } else { + wm->pen_is_down = 0; + wm97xx_reg_write(wm, AC97_GPIO_POLARITY, pol | + WM97XX_GPIO_13); + } + + if (wm->id == WM9712_ID2) + wm97xx_reg_write(wm, AC97_GPIO_STATUS, (status & + ~WM97XX_GPIO_13) << 1); + else + wm97xx_reg_write(wm, AC97_GPIO_STATUS, status & + ~WM97XX_GPIO_13); + mutex_unlock(&wm->codec_mutex); + } + + /* If the system is not using continuous mode or it provides a + * pen down operation then we need to schedule polls while the + * pen is down. Otherwise the machine driver is responsible + * for scheduling reads. + */ + if (!wm->mach_ops->acc_enabled || wm->mach_ops->acc_pen_down) { + if (wm->pen_is_down && !pen_was_down) { + /* Data is not availiable immediately on pen down */ + queue_delayed_work(wm->ts_workq, &wm->ts_reader, 1); + } + + /* Let ts_reader report the pen up for debounce. */ + if (!wm->pen_is_down && pen_was_down) + wm->pen_is_down = 1; + } + + if (!wm->pen_is_down && wm->mach_ops->acc_enabled) + wm->mach_ops->acc_pen_up(wm); + + wm->mach_ops->irq_enable(wm, 1); +} + +/* + * Codec PENDOWN irq handler + * + * We have to disable the codec interrupt in the handler because it + * can take upto 1ms to clear the interrupt source. We schedule a task + * in a work queue to do the actual interaction with the chip (it + * doesn't matter if we end up reenqueing it before it is executed + * since we don't touch the chip until it has run). The interrupt is + * then enabled again in the slow handler when the source has been + * cleared. + */ +static irqreturn_t wm97xx_pen_interrupt(int irq, void *dev_id) +{ + struct wm97xx *wm = dev_id; + + wm->mach_ops->irq_enable(wm, 0); + queue_work(wm->ts_workq, &wm->pen_event_work); + + return IRQ_HANDLED; +} + +/* + * initialise pen IRQ handler and workqueue + */ +static int wm97xx_init_pen_irq(struct wm97xx *wm) +{ + u16 reg; + + /* If an interrupt is supplied an IRQ enable operation must also be + * provided. */ + BUG_ON(!wm->mach_ops->irq_enable); + + if (request_irq(wm->pen_irq, wm97xx_pen_interrupt, IRQF_SHARED, + "wm97xx-pen", wm)) { + dev_err(wm->dev, + "Failed to register pen down interrupt, polling"); + wm->pen_irq = 0; + return -EINVAL; + } + + /* Configure GPIO as interrupt source on WM971x */ + if (wm->id != WM9705_ID2) { + BUG_ON(!wm->mach_ops->irq_gpio); + reg = wm97xx_reg_read(wm, AC97_MISC_AFE); + wm97xx_reg_write(wm, AC97_MISC_AFE, + reg & ~(wm->mach_ops->irq_gpio)); + reg = wm97xx_reg_read(wm, 0x5a); + wm97xx_reg_write(wm, 0x5a, reg & ~0x0001); + } + + return 0; +} + +static int wm97xx_read_samples(struct wm97xx *wm) +{ + struct wm97xx_data data; + int rc; + + mutex_lock(&wm->codec_mutex); + + if (wm->mach_ops && wm->mach_ops->acc_enabled) + rc = wm->mach_ops->acc_pen_down(wm); + else + rc = wm->codec->poll_touch(wm, &data); + + if (rc & RC_PENUP) { + if (wm->pen_is_down) { + wm->pen_is_down = 0; + dev_dbg(wm->dev, "pen up\n"); + input_report_abs(wm->input_dev, ABS_PRESSURE, 0); + input_sync(wm->input_dev); + } else if (!(rc & RC_AGAIN)) { + /* We need high frequency updates only while + * pen is down, the user never will be able to + * touch screen faster than a few times per + * second... On the other hand, when the user + * is actively working with the touchscreen we + * don't want to lose the quick response. So we + * will slowly increase sleep time after the + * pen is up and quicky restore it to ~one task + * switch when pen is down again. + */ + if (wm->ts_reader_interval < HZ / 10) + wm->ts_reader_interval++; + } + + } else if (rc & RC_VALID) { + dev_dbg(wm->dev, + "pen down: x=%x:%d, y=%x:%d, pressure=%x:%d\n", + data.x >> 12, data.x & 0xfff, data.y >> 12, + data.y & 0xfff, data.p >> 12, data.p & 0xfff); + input_report_abs(wm->input_dev, ABS_X, data.x & 0xfff); + input_report_abs(wm->input_dev, ABS_Y, data.y & 0xfff); + input_report_abs(wm->input_dev, ABS_PRESSURE, data.p & 0xfff); + input_sync(wm->input_dev); + wm->pen_is_down = 1; + wm->ts_reader_interval = wm->ts_reader_min_interval; + } else if (rc & RC_PENDOWN) { + dev_dbg(wm->dev, "pen down\n"); + wm->pen_is_down = 1; + wm->ts_reader_interval = wm->ts_reader_min_interval; + } + + mutex_unlock(&wm->codec_mutex); + return rc; +} + +/* +* The touchscreen sample reader. +*/ +static void wm97xx_ts_reader(struct work_struct *work) +{ + int rc; + struct wm97xx *wm = container_of(work, struct wm97xx, ts_reader.work); + + BUG_ON(!wm->codec); + + do { + rc = wm97xx_read_samples(wm); + } while (rc & RC_AGAIN); + + if (wm->pen_is_down || !wm->pen_irq) + queue_delayed_work(wm->ts_workq, &wm->ts_reader, + wm->ts_reader_interval); +} + +/** + * wm97xx_ts_input_open - Open the touch screen input device. + * @idev: Input device to be opened. + * + * Called by the input sub system to open a wm97xx touchscreen device. + * Starts the touchscreen thread and touch digitiser. + */ +static int wm97xx_ts_input_open(struct input_dev *idev) +{ + struct wm97xx *wm = input_get_drvdata(idev); + + wm->ts_workq = create_singlethread_workqueue("kwm97xx"); + if (wm->ts_workq == NULL) { + dev_err(wm->dev, + "Failed to create workqueue\n"); + return -EINVAL; + } + + /* start digitiser */ + if (wm->mach_ops && wm->mach_ops->acc_enabled) + wm->codec->acc_enable(wm, 1); + wm->codec->dig_enable(wm, 1); + + INIT_DELAYED_WORK(&wm->ts_reader, wm97xx_ts_reader); + INIT_WORK(&wm->pen_event_work, wm97xx_pen_irq_worker); + + wm->ts_reader_min_interval = HZ >= 100 ? HZ / 100 : 1; + if (wm->ts_reader_min_interval < 1) + wm->ts_reader_min_interval = 1; + wm->ts_reader_interval = wm->ts_reader_min_interval; + + wm->pen_is_down = 0; + if (wm->pen_irq) + wm97xx_init_pen_irq(wm); + else + dev_err(wm->dev, "No IRQ specified\n"); + + /* If we either don't have an interrupt for pen down events or + * failed to acquire it then we need to poll. + */ + if (wm->pen_irq == 0) + queue_delayed_work(wm->ts_workq, &wm->ts_reader, + wm->ts_reader_interval); + + return 0; +} + +/** + * wm97xx_ts_input_close - Close the touch screen input device. + * @idev: Input device to be closed. + * + * Called by the input sub system to close a wm97xx touchscreen + * device. Kills the touchscreen thread and stops the touch + * digitiser. + */ + +static void wm97xx_ts_input_close(struct input_dev *idev) +{ + struct wm97xx *wm = input_get_drvdata(idev); + u16 reg; + + if (wm->pen_irq) { + /* Return the interrupt to GPIO usage (disabling it) */ + if (wm->id != WM9705_ID2) { + BUG_ON(!wm->mach_ops->irq_gpio); + reg = wm97xx_reg_read(wm, AC97_MISC_AFE); + wm97xx_reg_write(wm, AC97_MISC_AFE, + reg | wm->mach_ops->irq_gpio); + } + + free_irq(wm->pen_irq, wm); + } + + wm->pen_is_down = 0; + + /* Balance out interrupt disables/enables */ + if (cancel_work_sync(&wm->pen_event_work)) + wm->mach_ops->irq_enable(wm, 1); + + /* ts_reader rearms itself so we need to explicitly stop it + * before we destroy the workqueue. + */ + cancel_delayed_work_sync(&wm->ts_reader); + + destroy_workqueue(wm->ts_workq); + + /* stop digitiser */ + wm->codec->dig_enable(wm, 0); + if (wm->mach_ops && wm->mach_ops->acc_enabled) + wm->codec->acc_enable(wm, 0); +} + +static int wm97xx_probe(struct device *dev) +{ + struct wm97xx *wm; + int ret = 0, id = 0; + + wm = kzalloc(sizeof(struct wm97xx), GFP_KERNEL); + if (!wm) + return -ENOMEM; + mutex_init(&wm->codec_mutex); + + wm->dev = dev; + dev->driver_data = wm; + wm->ac97 = to_ac97_t(dev); + + /* check that we have a supported codec */ + id = wm97xx_reg_read(wm, AC97_VENDOR_ID1); + if (id != WM97XX_ID1) { + dev_err(dev, "Device with vendor %04x is not a wm97xx\n", id); + ret = -ENODEV; + goto alloc_err; + } + + wm->id = wm97xx_reg_read(wm, AC97_VENDOR_ID2); + + dev_info(wm->dev, "detected a wm97%02x codec\n", wm->id & 0xff); + + switch (wm->id & 0xff) { +#ifdef CONFIG_TOUCHSCREEN_WM9705 + case 0x05: + wm->codec = &wm9705_codec; + break; +#endif +#ifdef CONFIG_TOUCHSCREEN_WM9712 + case 0x12: + wm->codec = &wm9712_codec; + break; +#endif +#ifdef CONFIG_TOUCHSCREEN_WM9713 + case 0x13: + wm->codec = &wm9713_codec; + break; +#endif + default: + dev_err(wm->dev, "Support for wm97%02x not compiled in.\n", + wm->id & 0xff); + ret = -ENODEV; + goto alloc_err; + } + + wm->input_dev = input_allocate_device(); + if (wm->input_dev == NULL) { + ret = -ENOMEM; + goto alloc_err; + } + + /* set up touch configuration */ + wm->input_dev->name = "wm97xx touchscreen"; + wm->input_dev->open = wm97xx_ts_input_open; + wm->input_dev->close = wm97xx_ts_input_close; + set_bit(EV_ABS, wm->input_dev->evbit); + set_bit(ABS_X, wm->input_dev->absbit); + set_bit(ABS_Y, wm->input_dev->absbit); + set_bit(ABS_PRESSURE, wm->input_dev->absbit); + input_set_abs_params(wm->input_dev, ABS_X, abs_x[0], abs_x[1], + abs_x[2], 0); + input_set_abs_params(wm->input_dev, ABS_Y, abs_y[0], abs_y[1], + abs_y[2], 0); + input_set_abs_params(wm->input_dev, ABS_PRESSURE, abs_p[0], abs_p[1], + abs_p[2], 0); + input_set_drvdata(wm->input_dev, wm); + wm->input_dev->dev.parent = dev; + ret = input_register_device(wm->input_dev); + if (ret < 0) + goto dev_alloc_err; + + /* set up physical characteristics */ + wm->codec->phy_init(wm); + + /* load gpio cache */ + wm->gpio[0] = wm97xx_reg_read(wm, AC97_GPIO_CFG); + wm->gpio[1] = wm97xx_reg_read(wm, AC97_GPIO_POLARITY); + wm->gpio[2] = wm97xx_reg_read(wm, AC97_GPIO_STICKY); + wm->gpio[3] = wm97xx_reg_read(wm, AC97_GPIO_WAKEUP); + wm->gpio[4] = wm97xx_reg_read(wm, AC97_GPIO_STATUS); + wm->gpio[5] = wm97xx_reg_read(wm, AC97_MISC_AFE); + + /* register our battery device */ + wm->battery_dev = platform_device_alloc("wm97xx-battery", -1); + if (!wm->battery_dev) { + ret = -ENOMEM; + goto batt_err; + } + platform_set_drvdata(wm->battery_dev, wm); + wm->battery_dev->dev.parent = dev; + ret = platform_device_add(wm->battery_dev); + if (ret < 0) + goto batt_reg_err; + + /* register our extended touch device (for machine specific + * extensions) */ + wm->touch_dev = platform_device_alloc("wm97xx-touch", -1); + if (!wm->touch_dev) { + ret = -ENOMEM; + goto touch_err; + } + platform_set_drvdata(wm->touch_dev, wm); + wm->touch_dev->dev.parent = dev; + ret = platform_device_add(wm->touch_dev); + if (ret < 0) + goto touch_reg_err; + + return ret; + + touch_reg_err: + platform_device_put(wm->touch_dev); + touch_err: + platform_device_unregister(wm->battery_dev); + wm->battery_dev = NULL; + batt_reg_err: + platform_device_put(wm->battery_dev); + batt_err: + input_unregister_device(wm->input_dev); + wm->input_dev = NULL; + dev_alloc_err: + input_free_device(wm->input_dev); + alloc_err: + kfree(wm); + + return ret; +} + +static int wm97xx_remove(struct device *dev) +{ + struct wm97xx *wm = dev_get_drvdata(dev); + + platform_device_unregister(wm->battery_dev); + platform_device_unregister(wm->touch_dev); + input_unregister_device(wm->input_dev); + kfree(wm); + + return 0; +} + +#ifdef CONFIG_PM +static int wm97xx_suspend(struct device *dev, pm_message_t state) +{ + struct wm97xx *wm = dev_get_drvdata(dev); + + if (wm->input_dev->users) + cancel_delayed_work_sync(&wm->ts_reader); + + return 0; +} + +static int wm97xx_resume(struct device *dev) +{ + struct wm97xx *wm = dev_get_drvdata(dev); + + /* restore digitiser and gpios */ + if (wm->id == WM9713_ID2) { + wm97xx_reg_write(wm, AC97_WM9713_DIG1, wm->dig[0]); + wm97xx_reg_write(wm, 0x5a, wm->misc); + if (wm->input_dev->users) { + u16 reg; + reg = wm97xx_reg_read(wm, AC97_EXTENDED_MID) & 0x7fff; + wm97xx_reg_write(wm, AC97_EXTENDED_MID, reg); + } + } + + wm97xx_reg_write(wm, AC97_WM9713_DIG2, wm->dig[1]); + wm97xx_reg_write(wm, AC97_WM9713_DIG3, wm->dig[2]); + + wm97xx_reg_write(wm, AC97_GPIO_CFG, wm->gpio[0]); + wm97xx_reg_write(wm, AC97_GPIO_POLARITY, wm->gpio[1]); + wm97xx_reg_write(wm, AC97_GPIO_STICKY, wm->gpio[2]); + wm97xx_reg_write(wm, AC97_GPIO_WAKEUP, wm->gpio[3]); + wm97xx_reg_write(wm, AC97_GPIO_STATUS, wm->gpio[4]); + wm97xx_reg_write(wm, AC97_MISC_AFE, wm->gpio[5]); + + if (wm->input_dev->users && !wm->pen_irq) { + wm->ts_reader_interval = wm->ts_reader_min_interval; + queue_delayed_work(wm->ts_workq, &wm->ts_reader, + wm->ts_reader_interval); + } + + return 0; +} + +#else +#define wm97xx_suspend NULL +#define wm97xx_resume NULL +#endif + +/* + * Machine specific operations + */ +int wm97xx_register_mach_ops(struct wm97xx *wm, + struct wm97xx_mach_ops *mach_ops) +{ + mutex_lock(&wm->codec_mutex); + if (wm->mach_ops) { + mutex_unlock(&wm->codec_mutex); + return -EINVAL; + } + wm->mach_ops = mach_ops; + mutex_unlock(&wm->codec_mutex); + + return 0; +} +EXPORT_SYMBOL_GPL(wm97xx_register_mach_ops); + +void wm97xx_unregister_mach_ops(struct wm97xx *wm) +{ + mutex_lock(&wm->codec_mutex); + wm->mach_ops = NULL; + mutex_unlock(&wm->codec_mutex); +} +EXPORT_SYMBOL_GPL(wm97xx_unregister_mach_ops); + +static struct device_driver wm97xx_driver = { + .name = "ac97", + .bus = &ac97_bus_type, + .owner = THIS_MODULE, + .probe = wm97xx_probe, + .remove = wm97xx_remove, + .suspend = wm97xx_suspend, + .resume = wm97xx_resume, +}; + +static int __init wm97xx_init(void) +{ + return driver_register(&wm97xx_driver); +} + +static void __exit wm97xx_exit(void) +{ + driver_unregister(&wm97xx_driver); +} + +module_init(wm97xx_init); +module_exit(wm97xx_exit); + +/* Module information */ +MODULE_AUTHOR("Liam Girdwood <liam.girdwood@wolfsonmicro.com>"); +MODULE_DESCRIPTION("WM97xx Core - Touch Screen / AUX ADC / GPIO Driver"); +MODULE_LICENSE("GPL"); diff --git a/include/linux/wm97xx.h b/include/linux/wm97xx.h new file mode 100644 index 0000000..ed01c7d --- /dev/null +++ b/include/linux/wm97xx.h @@ -0,0 +1,311 @@ + +/* + * Register bits and API for Wolfson WM97xx series of codecs + */ + +#ifndef _LINUX_WM97XX_H +#define _LINUX_WM97XX_H + +#include <sound/core.h> +#include <sound/pcm.h> +#include <sound/ac97_codec.h> +#include <sound/initval.h> +#include <linux/types.h> +#include <linux/list.h> +#include <linux/input.h> /* Input device layer */ +#include <linux/platform_device.h> + +/* + * WM97xx AC97 Touchscreen registers + */ +#define AC97_WM97XX_DIGITISER1 0x76 +#define AC97_WM97XX_DIGITISER2 0x78 +#define AC97_WM97XX_DIGITISER_RD 0x7a +#define AC97_WM9713_DIG1 0x74 +#define AC97_WM9713_DIG2 AC97_WM97XX_DIGITISER1 +#define AC97_WM9713_DIG3 AC97_WM97XX_DIGITISER2 + +/* + * WM97xx register bits + */ +#define WM97XX_POLL 0x8000 /* initiate a polling measurement */ +#define WM97XX_ADCSEL_X 0x1000 /* x coord measurement */ +#define WM97XX_ADCSEL_Y 0x2000 /* y coord measurement */ +#define WM97XX_ADCSEL_PRES 0x3000 /* pressure measurement */ +#define WM97XX_ADCSEL_MASK 0x7000 +#define WM97XX_COO 0x0800 /* enable coordinate mode */ +#define WM97XX_CTC 0x0400 /* enable continuous mode */ +#define WM97XX_CM_RATE_93 0x0000 /* 93.75Hz continuous rate */ +#define WM97XX_CM_RATE_187 0x0100 /* 187.5Hz continuous rate */ +#define WM97XX_CM_RATE_375 0x0200 /* 375Hz continuous rate */ +#define WM97XX_CM_RATE_750 0x0300 /* 750Hz continuous rate */ +#define WM97XX_CM_RATE_8K 0x00f0 /* 8kHz continuous rate */ +#define WM97XX_CM_RATE_12K 0x01f0 /* 12kHz continuous rate */ +#define WM97XX_CM_RATE_24K 0x02f0 /* 24kHz continuous rate */ +#define WM97XX_CM_RATE_48K 0x03f0 /* 48kHz continuous rate */ +#define WM97XX_CM_RATE_MASK 0x03f0 +#define WM97XX_RATE(i) (((i & 3) << 8) | ((i & 4) ? 0xf0 : 0)) +#define WM97XX_DELAY(i) ((i << 4) & 0x00f0) /* sample delay times */ +#define WM97XX_DELAY_MASK 0x00f0 +#define WM97XX_SLEN 0x0008 /* slot read back enable */ +#define WM97XX_SLT(i) ((i - 5) & 0x7) /* panel slot (5-11) */ +#define WM97XX_SLT_MASK 0x0007 +#define WM97XX_PRP_DETW 0x4000 /* detect on, digitise off, wake */ +#define WM97XX_PRP_DET 0x8000 /* detect on, digitise off, no wake */ +#define WM97XX_PRP_DET_DIG 0xc000 /* setect on, digitise on */ +#define WM97XX_RPR 0x2000 /* wake up on pen down */ +#define WM97XX_PEN_DOWN 0x8000 /* pen is down */ +#define WM97XX_ADCSRC_MASK 0x7000 /* ADC source mask */ + +#define WM97XX_AUX_ID1 0x8001 +#define WM97XX_AUX_ID2 0x8002 +#define WM97XX_AUX_ID3 0x8003 +#define WM97XX_AUX_ID4 0x8004 + + +/* WM9712 Bits */ +#define WM9712_45W 0x1000 /* set for 5-wire touchscreen */ +#define WM9712_PDEN 0x0800 /* measure only when pen down */ +#define WM9712_WAIT 0x0200 /* wait until adc is read before next sample */ +#define WM9712_PIL 0x0100 /* current used for pressure measurement. set 400uA else 200uA */ +#define WM9712_MASK_HI 0x0040 /* hi on mask pin (47) stops conversions */ +#define WM9712_MASK_EDGE 0x0080 /* rising/falling edge on pin delays sample */ +#define WM9712_MASK_SYNC 0x00c0 /* rising/falling edge on mask initiates sample */ +#define WM9712_RPU(i) (i&0x3f) /* internal pull up on pen detect (64k / rpu) */ +#define WM9712_PD(i) (0x1 << i) /* power management */ + +/* WM9712 Registers */ +#define AC97_WM9712_POWER 0x24 +#define AC97_WM9712_REV 0x58 + +/* WM9705 Bits */ +#define WM9705_PDEN 0x1000 /* measure only when pen is down */ +#define WM9705_PINV 0x0800 /* inverts sense of pen down output */ +#define WM9705_BSEN 0x0400 /* BUSY flag enable, pin47 is 1 when busy */ +#define WM9705_BINV 0x0200 /* invert BUSY (pin47) output */ +#define WM9705_WAIT 0x0100 /* wait until adc is read before next sample */ +#define WM9705_PIL 0x0080 /* current used for pressure measurement. set 400uA else 200uA */ +#define WM9705_PHIZ 0x0040 /* set PHONE and PCBEEP inputs to high impedance */ +#define WM9705_MASK_HI 0x0010 /* hi on mask stops conversions */ +#define WM9705_MASK_EDGE 0x0020 /* rising/falling edge on pin delays sample */ +#define WM9705_MASK_SYNC 0x0030 /* rising/falling edge on mask initiates sample */ +#define WM9705_PDD(i) (i & 0x000f) /* pen detect comparator threshold */ + + +/* WM9713 Bits */ +#define WM9713_PDPOL 0x0400 /* Pen down polarity */ +#define WM9713_POLL 0x0200 /* initiate a polling measurement */ +#define WM9713_CTC 0x0100 /* enable continuous mode */ +#define WM9713_ADCSEL_X 0x0002 /* X measurement */ +#define WM9713_ADCSEL_Y 0x0004 /* Y measurement */ +#define WM9713_ADCSEL_PRES 0x0008 /* Pressure measurement */ +#define WM9713_COO 0x0001 /* enable coordinate mode */ +#define WM9713_PDEN 0x0800 /* measure only when pen down */ +#define WM9713_ADCSEL_MASK 0x00fe /* ADC selection mask */ +#define WM9713_WAIT 0x0200 /* coordinate wait */ + +/* AUX ADC ID's */ +#define TS_COMP1 0x0 +#define TS_COMP2 0x1 +#define TS_BMON 0x2 +#define TS_WIPER 0x3 + +/* ID numbers */ +#define WM97XX_ID1 0x574d +#define WM9712_ID2 0x4c12 +#define WM9705_ID2 0x4c05 +#define WM9713_ID2 0x4c13 + +/* Codec GPIO's */ +#define WM97XX_MAX_GPIO 16 +#define WM97XX_GPIO_1 (1 << 1) +#define WM97XX_GPIO_2 (1 << 2) +#define WM97XX_GPIO_3 (1 << 3) +#define WM97XX_GPIO_4 (1 << 4) +#define WM97XX_GPIO_5 (1 << 5) +#define WM97XX_GPIO_6 (1 << 6) +#define WM97XX_GPIO_7 (1 << 7) +#define WM97XX_GPIO_8 (1 << 8) +#define WM97XX_GPIO_9 (1 << 9) +#define WM97XX_GPIO_10 (1 << 10) +#define WM97XX_GPIO_11 (1 << 11) +#define WM97XX_GPIO_12 (1 << 12) +#define WM97XX_GPIO_13 (1 << 13) +#define WM97XX_GPIO_14 (1 << 14) +#define WM97XX_GPIO_15 (1 << 15) + + +#define AC97_LINK_FRAME 21 /* time in uS for AC97 link frame */ + + +/*---------------- Return codes from sample reading functions ---------------*/ + +/* More data is available; call the sample gathering function again */ +#define RC_AGAIN 0x00000001 +/* The returned sample is valid */ +#define RC_VALID 0x00000002 +/* The pen is up (the first RC_VALID without RC_PENUP means pen is down) */ +#define RC_PENUP 0x00000004 +/* The pen is down (RC_VALID implies RC_PENDOWN, but sometimes it is helpful + to tell the handler that the pen is down but we don't know yet his coords, + so the handler should not sleep or wait for pendown irq) */ +#define RC_PENDOWN 0x00000008 + +/* + * The wm97xx driver provides a private API for writing platform-specific + * drivers. + */ + +/* The structure used to return arch specific sampled data into */ +struct wm97xx_data { + int x; + int y; + int p; +}; + +/* + * Codec GPIO status + */ +enum wm97xx_gpio_status { + WM97XX_GPIO_HIGH, + WM97XX_GPIO_LOW +}; + +/* + * Codec GPIO direction + */ +enum wm97xx_gpio_dir { + WM97XX_GPIO_IN, + WM97XX_GPIO_OUT +}; + +/* + * Codec GPIO polarity + */ +enum wm97xx_gpio_pol { + WM97XX_GPIO_POL_HIGH, + WM97XX_GPIO_POL_LOW +}; + +/* + * Codec GPIO sticky + */ +enum wm97xx_gpio_sticky { + WM97XX_GPIO_STICKY, + WM97XX_GPIO_NOTSTICKY +}; + +/* + * Codec GPIO wake + */ +enum wm97xx_gpio_wake { + WM97XX_GPIO_WAKE, + WM97XX_GPIO_NOWAKE +}; + +/* + * Digitiser ioctl commands + */ +#define WM97XX_DIG_START 0x1 +#define WM97XX_DIG_STOP 0x2 +#define WM97XX_PHY_INIT 0x3 +#define WM97XX_AUX_PREPARE 0x4 +#define WM97XX_DIG_RESTORE 0x5 + +struct wm97xx; + +extern struct wm97xx_codec_drv wm9705_codec; +extern struct wm97xx_codec_drv wm9712_codec; +extern struct wm97xx_codec_drv wm9713_codec; + +/* + * Codec driver interface - allows mapping to WM9705/12/13 and newer codecs + */ +struct wm97xx_codec_drv { + u16 id; + char *name; + + /* read 1 sample */ + int (*poll_sample) (struct wm97xx *, int adcsel, int *sample); + + /* read X,Y,[P] in poll */ + int (*poll_touch) (struct wm97xx *, struct wm97xx_data *); + + int (*acc_enable) (struct wm97xx *, int enable); + void (*phy_init) (struct wm97xx *); + void (*dig_enable) (struct wm97xx *, int enable); + void (*dig_restore) (struct wm97xx *); + void (*aux_prepare) (struct wm97xx *); +}; + + +/* Machine specific and accelerated touch operations */ +struct wm97xx_mach_ops { + + /* accelerated touch readback - coords are transmited on AC97 link */ + int acc_enabled; + void (*acc_pen_up) (struct wm97xx *); + int (*acc_pen_down) (struct wm97xx *); + int (*acc_startup) (struct wm97xx *); + void (*acc_shutdown) (struct wm97xx *); + + /* interrupt mask control - required for accelerated operation */ + void (*irq_enable) (struct wm97xx *, int enable); + + /* GPIO pin used for accelerated operation */ + int irq_gpio; + + /* pre and post sample - can be used to minimise any analog noise */ + void (*pre_sample) (int); /* function to run before sampling */ + void (*post_sample) (int); /* function to run after sampling */ +}; + +struct wm97xx { + u16 dig[3], id, gpio[6], misc; /* Cached codec registers */ + u16 dig_save[3]; /* saved during aux reading */ + struct wm97xx_codec_drv *codec; /* attached codec driver*/ + struct input_dev *input_dev; /* touchscreen input device */ + struct snd_ac97 *ac97; /* ALSA codec access */ + struct device *dev; /* ALSA device */ + struct platform_device *battery_dev; + struct platform_device *touch_dev; + struct wm97xx_mach_ops *mach_ops; + struct mutex codec_mutex; + struct delayed_work ts_reader; /* Used to poll touchscreen */ + unsigned long ts_reader_interval; /* Current interval for timer */ + unsigned long ts_reader_min_interval; /* Minimum interval */ + unsigned int pen_irq; /* Pen IRQ number in use */ + struct workqueue_struct *ts_workq; + struct work_struct pen_event_work; + u16 acc_slot; /* AC97 slot used for acc touch data */ + u16 acc_rate; /* acc touch data rate */ + unsigned pen_is_down:1; /* Pen is down */ + unsigned aux_waiting:1; /* aux measurement waiting */ + unsigned pen_probably_down:1; /* used in polling mode */ +}; + +/* + * Codec GPIO access (not supported on WM9705) + * This can be used to set/get codec GPIO and Virtual GPIO status. + */ +enum wm97xx_gpio_status wm97xx_get_gpio(struct wm97xx *wm, u32 gpio); +void wm97xx_set_gpio(struct wm97xx *wm, u32 gpio, + enum wm97xx_gpio_status status); +void wm97xx_config_gpio(struct wm97xx *wm, u32 gpio, + enum wm97xx_gpio_dir dir, + enum wm97xx_gpio_pol pol, + enum wm97xx_gpio_sticky sticky, + enum wm97xx_gpio_wake wake); + +/* codec AC97 IO access */ +int wm97xx_reg_read(struct wm97xx *wm, u16 reg); +void wm97xx_reg_write(struct wm97xx *wm, u16 reg, u16 val); + +/* aux adc readback */ +int wm97xx_read_aux_adc(struct wm97xx *wm, u16 adcsel); + +/* machine ops */ +int wm97xx_register_mach_ops(struct wm97xx *, struct wm97xx_mach_ops *); +void wm97xx_unregister_mach_ops(struct wm97xx *); + +#endif |