diff options
Diffstat (limited to 'Documentation/hwmon')
| -rw-r--r-- | Documentation/hwmon/adm1021 | 36 | ||||
| -rw-r--r-- | Documentation/hwmon/lm90 | 29 | ||||
| -rw-r--r-- | Documentation/hwmon/max16064 | 62 | ||||
| -rw-r--r-- | Documentation/hwmon/max34440 | 79 | ||||
| -rw-r--r-- | Documentation/hwmon/max8688 | 69 | ||||
| -rw-r--r-- | Documentation/hwmon/pmbus | 34 | ||||
| -rw-r--r-- | Documentation/hwmon/smm665 | 8 | ||||
| -rw-r--r-- | Documentation/hwmon/submitting-patches | 109 |
8 files changed, 370 insertions, 56 deletions
diff --git a/Documentation/hwmon/adm1021 b/Documentation/hwmon/adm1021 index 03d02bf..02ad96c 100644 --- a/Documentation/hwmon/adm1021 +++ b/Documentation/hwmon/adm1021 @@ -14,10 +14,6 @@ Supported chips: Prefix: 'gl523sm' Addresses scanned: I2C 0x18 - 0x1a, 0x29 - 0x2b, 0x4c - 0x4e Datasheet: - * Intel Xeon Processor - Prefix: - any other - may require 'force_adm1021' parameter - Addresses scanned: none - Datasheet: Publicly available at Intel website * Maxim MAX1617 Prefix: 'max1617' Addresses scanned: I2C 0x18 - 0x1a, 0x29 - 0x2b, 0x4c - 0x4e @@ -91,21 +87,27 @@ will do no harm, but will return 'old' values. It is possible to make ADM1021-clones do faster measurements, but there is really no good reason for that. -Xeon support ------------- -Some Xeon processors have real max1617, adm1021, or compatible chips -within them, with two temperature sensors. +Netburst-based Xeon support +--------------------------- -Other Xeons have chips with only one sensor. +Some Xeon processors based on the Netburst (early Pentium 4, from 2001 to +2003) microarchitecture had real MAX1617, ADM1021, or compatible chips +within them, with two temperature sensors. Other Xeon processors of this +era (with 400 MHz FSB) had chips with only one temperature sensor. -If you have a Xeon, and the adm1021 module loads, and both temperatures -appear valid, then things are good. +If you have such an old Xeon, and you get two valid temperatures when +loading the adm1021 module, then things are good. -If the adm1021 module doesn't load, you should try this: - modprobe adm1021 force_adm1021=BUS,ADDRESS - ADDRESS can only be 0x18, 0x1a, 0x29, 0x2b, 0x4c, or 0x4e. +If nothing happens when loading the adm1021 module, and you are certain +that your specific Xeon processor model includes compatible sensors, you +will have to explicitly instantiate the sensor chips from user-space. See +method 4 in Documentation/i2c/instantiating-devices. Possible slave +addresses are 0x18, 0x1a, 0x29, 0x2b, 0x4c, or 0x4e. It is likely that +only temp2 will be correct and temp1 will have to be ignored. -If you have dual Xeons you may have appear to have two separate -adm1021-compatible chips, or two single-temperature sensors, at distinct -addresses. +Previous generations of the Xeon processor (based on Pentium II/III) +didn't have these sensors. Next generations of Xeon processors (533 MHz +FSB and faster) lost them, until the Core-based generation which +introduced integrated digital thermal sensors. These are supported by +the coretemp driver. diff --git a/Documentation/hwmon/lm90 b/Documentation/hwmon/lm90 index fa475c0..f3efd18 100644 --- a/Documentation/hwmon/lm90 +++ b/Documentation/hwmon/lm90 @@ -32,6 +32,16 @@ Supported chips: Addresses scanned: I2C 0x4c and 0x4d Datasheet: Publicly available at the ON Semiconductor website http://www.onsemi.com/PowerSolutions/product.do?id=ADT7461 + * Analog Devices ADT7461A + Prefix: 'adt7461a' + Addresses scanned: I2C 0x4c and 0x4d + Datasheet: Publicly available at the ON Semiconductor website + http://www.onsemi.com/PowerSolutions/product.do?id=ADT7461A + * ON Semiconductor NCT1008 + Prefix: 'nct1008' + Addresses scanned: I2C 0x4c and 0x4d + Datasheet: Publicly available at the ON Semiconductor website + http://www.onsemi.com/PowerSolutions/product.do?id=NCT1008 * Maxim MAX6646 Prefix: 'max6646' Addresses scanned: I2C 0x4d @@ -149,7 +159,7 @@ ADM1032: * ALERT is triggered by open remote sensor. * SMBus PEC support for Write Byte and Receive Byte transactions. -ADT7461: +ADT7461, ADT7461A, NCT1008: * Extended temperature range (breaks compatibility) * Lower resolution for remote temperature @@ -195,9 +205,9 @@ are exported, one for each channel, but these values are of course linked. Only the local hysteresis can be set from user-space, and the same delta applies to the remote hysteresis. -The lm90 driver will not update its values more frequently than every -other second; reading them more often will do no harm, but will return -'old' values. +The lm90 driver will not update its values more frequently than configured with +the update_interval attribute; reading them more often will do no harm, but will +return 'old' values. SMBus Alert Support ------------------- @@ -205,11 +215,12 @@ SMBus Alert Support This driver has basic support for SMBus alert. When an alert is received, the status register is read and the faulty temperature channel is logged. -The Analog Devices chips (ADM1032 and ADT7461) do not implement the SMBus -alert protocol properly so additional care is needed: the ALERT output is -disabled when an alert is received, and is re-enabled only when the alarm -is gone. Otherwise the chip would block alerts from other chips in the bus -as long as the alarm is active. +The Analog Devices chips (ADM1032, ADT7461 and ADT7461A) and ON +Semiconductor chips (NCT1008) do not implement the SMBus alert protocol +properly so additional care is needed: the ALERT output is disabled when +an alert is received, and is re-enabled only when the alarm is gone. +Otherwise the chip would block alerts from other chips in the bus as long +as the alarm is active. PEC Support ----------- diff --git a/Documentation/hwmon/max16064 b/Documentation/hwmon/max16064 new file mode 100644 index 0000000..4172899 --- /dev/null +++ b/Documentation/hwmon/max16064 @@ -0,0 +1,62 @@ +Kernel driver max16064 +====================== + +Supported chips: + * Maxim MAX16064 + Prefix: 'max16064' + Addresses scanned: - + Datasheet: http://datasheets.maxim-ic.com/en/ds/MAX16064.pdf + +Author: Guenter Roeck <guenter.roeck@ericsson.com> + + +Description +----------- + +This driver supports hardware montoring for Maxim MAX16064 Quad Power-Supply +Controller with Active-Voltage Output Control and PMBus Interface. + +The driver is a client driver to the core PMBus driver. +Please see Documentation/hwmon/pmbus for details on PMBus client drivers. + + +Usage Notes +----------- + +This driver does not auto-detect devices. You will have to instantiate the +devices explicitly. Please see Documentation/i2c/instantiating-devices for +details. + + +Platform data support +--------------------- + +The driver supports standard PMBus driver platform data. + + +Sysfs entries +------------- + +The following attributes are supported. Limits are read-write; all other +attributes are read-only. + +in[1-4]_label "vout[1-4]" +in[1-4]_input Measured voltage. From READ_VOUT register. +in[1-4]_min Minumum Voltage. From VOUT_UV_WARN_LIMIT register. +in[1-4]_max Maximum voltage. From VOUT_OV_WARN_LIMIT register. +in[1-4]_lcrit Critical minumum Voltage. VOUT_UV_FAULT_LIMIT register. +in[1-4]_crit Critical maximum voltage. From VOUT_OV_FAULT_LIMIT register. +in[1-4]_min_alarm Voltage low alarm. From VOLTAGE_UV_WARNING status. +in[1-4]_max_alarm Voltage high alarm. From VOLTAGE_OV_WARNING status. +in[1-4]_lcrit_alarm Voltage critical low alarm. From VOLTAGE_UV_FAULT status. +in[1-4]_crit_alarm Voltage critical high alarm. From VOLTAGE_OV_FAULT status. + +temp1_input Measured temperature. From READ_TEMPERATURE_1 register. +temp1_max Maximum temperature. From OT_WARN_LIMIT register. +temp1_crit Critical high temperature. From OT_FAULT_LIMIT register. +temp1_max_alarm Chip temperature high alarm. Set by comparing + READ_TEMPERATURE_1 with OT_WARN_LIMIT if TEMP_OT_WARNING + status is set. +temp1_crit_alarm Chip temperature critical high alarm. Set by comparing + READ_TEMPERATURE_1 with OT_FAULT_LIMIT if TEMP_OT_FAULT + status is set. diff --git a/Documentation/hwmon/max34440 b/Documentation/hwmon/max34440 new file mode 100644 index 0000000..6c525dd --- /dev/null +++ b/Documentation/hwmon/max34440 @@ -0,0 +1,79 @@ +Kernel driver max34440 +====================== + +Supported chips: + * Maxim MAX34440 + Prefixes: 'max34440' + Addresses scanned: - + Datasheet: http://datasheets.maxim-ic.com/en/ds/MAX34440.pdf + * Maxim MAX34441 + PMBus 5-Channel Power-Supply Manager and Intelligent Fan Controller + Prefixes: 'max34441' + Addresses scanned: - + Datasheet: http://datasheets.maxim-ic.com/en/ds/MAX34441.pdf + +Author: Guenter Roeck <guenter.roeck@ericsson.com> + + +Description +----------- + +This driver supports hardware montoring for Maxim MAX34440 PMBus 6-Channel +Power-Supply Manager and MAX34441 PMBus 5-Channel Power-Supply Manager +and Intelligent Fan Controller. + +The driver is a client driver to the core PMBus driver. Please see +Documentation/hwmon/pmbus for details on PMBus client drivers. + + +Usage Notes +----------- + +This driver does not auto-detect devices. You will have to instantiate the +devices explicitly. Please see Documentation/i2c/instantiating-devices for +details. + + +Platform data support +--------------------- + +The driver supports standard PMBus driver platform data. + + +Sysfs entries +------------- + +The following attributes are supported. Limits are read-write; all other +attributes are read-only. + +in[1-6]_label "vout[1-6]". +in[1-6]_input Measured voltage. From READ_VOUT register. +in[1-6]_min Minumum Voltage. From VOUT_UV_WARN_LIMIT register. +in[1-6]_max Maximum voltage. From VOUT_OV_WARN_LIMIT register. +in[1-6]_lcrit Critical minumum Voltage. VOUT_UV_FAULT_LIMIT register. +in[1-6]_crit Critical maximum voltage. From VOUT_OV_FAULT_LIMIT register. +in[1-6]_min_alarm Voltage low alarm. From VOLTAGE_UV_WARNING status. +in[1-6]_max_alarm Voltage high alarm. From VOLTAGE_OV_WARNING status. +in[1-6]_lcrit_alarm Voltage critical low alarm. From VOLTAGE_UV_FAULT status. +in[1-6]_crit_alarm Voltage critical high alarm. From VOLTAGE_OV_FAULT status. + +curr[1-6]_label "iout[1-6]". +curr[1-6]_input Measured current. From READ_IOUT register. +curr[1-6]_max Maximum current. From IOUT_OC_WARN_LIMIT register. +curr[1-6]_crit Critical maximum current. From IOUT_OC_FAULT_LIMIT register. +curr[1-6]_max_alarm Current high alarm. From IOUT_OC_WARNING status. +curr[1-6]_crit_alarm Current critical high alarm. From IOUT_OC_FAULT status. + + in6 and curr6 attributes only exist for MAX34440. + +temp[1-8]_input Measured temperatures. From READ_TEMPERATURE_1 register. + temp1 is the chip's internal temperature. temp2..temp5 + are remote I2C temperature sensors. For MAX34441, temp6 + is a remote thermal-diode sensor. For MAX34440, temp6..8 + are remote I2C temperature sensors. +temp[1-8]_max Maximum temperature. From OT_WARN_LIMIT register. +temp[1-8]_crit Critical high temperature. From OT_FAULT_LIMIT register. +temp[1-8]_max_alarm Temperature high alarm. +temp[1-8]_crit_alarm Temperature critical high alarm. + + temp7 and temp8 attributes only exist for MAX34440. diff --git a/Documentation/hwmon/max8688 b/Documentation/hwmon/max8688 new file mode 100644 index 0000000..0ddd3a4 --- /dev/null +++ b/Documentation/hwmon/max8688 @@ -0,0 +1,69 @@ +Kernel driver max8688 +===================== + +Supported chips: + * Maxim MAX8688 + Prefix: 'max8688' + Addresses scanned: - + Datasheet: http://datasheets.maxim-ic.com/en/ds/MAX8688.pdf + +Author: Guenter Roeck <guenter.roeck@ericsson.com> + + +Description +----------- + +This driver supports hardware montoring for Maxim MAX8688 Digital Power-Supply +Controller/Monitor with PMBus Interface. + +The driver is a client driver to the core PMBus driver. Please see +Documentation/hwmon/pmbus for details on PMBus client drivers. + + +Usage Notes +----------- + +This driver does not auto-detect devices. You will have to instantiate the +devices explicitly. Please see Documentation/i2c/instantiating-devices for +details. + + +Platform data support +--------------------- + +The driver supports standard PMBus driver platform data. + + +Sysfs entries +------------- + +The following attributes are supported. Limits are read-write; all other +attributes are read-only. + +in1_label "vout1" +in1_input Measured voltage. From READ_VOUT register. +in1_min Minumum Voltage. From VOUT_UV_WARN_LIMIT register. +in1_max Maximum voltage. From VOUT_OV_WARN_LIMIT register. +in1_lcrit Critical minumum Voltage. VOUT_UV_FAULT_LIMIT register. +in1_crit Critical maximum voltage. From VOUT_OV_FAULT_LIMIT register. +in1_min_alarm Voltage low alarm. From VOLTAGE_UV_WARNING status. +in1_max_alarm Voltage high alarm. From VOLTAGE_OV_WARNING status. +in1_lcrit_alarm Voltage critical low alarm. From VOLTAGE_UV_FAULT status. +in1_crit_alarm Voltage critical high alarm. From VOLTAGE_OV_FAULT status. + +curr1_label "iout1" +curr1_input Measured current. From READ_IOUT register. +curr1_max Maximum current. From IOUT_OC_WARN_LIMIT register. +curr1_crit Critical maximum current. From IOUT_OC_FAULT_LIMIT register. +curr1_max_alarm Current high alarm. From IOUT_OC_WARN_LIMIT register. +curr1_crit_alarm Current critical high alarm. From IOUT_OC_FAULT status. + +temp1_input Measured temperature. From READ_TEMPERATURE_1 register. +temp1_max Maximum temperature. From OT_WARN_LIMIT register. +temp1_crit Critical high temperature. From OT_FAULT_LIMIT register. +temp1_max_alarm Chip temperature high alarm. Set by comparing + READ_TEMPERATURE_1 with OT_WARN_LIMIT if TEMP_OT_WARNING + status is set. +temp1_crit_alarm Chip temperature critical high alarm. Set by comparing + READ_TEMPERATURE_1 with OT_FAULT_LIMIT if TEMP_OT_FAULT + status is set. diff --git a/Documentation/hwmon/pmbus b/Documentation/hwmon/pmbus index dc4933e..5e462fc 100644 --- a/Documentation/hwmon/pmbus +++ b/Documentation/hwmon/pmbus @@ -13,26 +13,6 @@ Supported chips: Prefix: 'ltc2978' Addresses scanned: - Datasheet: http://cds.linear.com/docs/Datasheet/2978fa.pdf - * Maxim MAX16064 - Quad Power-Supply Controller - Prefix: 'max16064' - Addresses scanned: - - Datasheet: http://datasheets.maxim-ic.com/en/ds/MAX16064.pdf - * Maxim MAX34440 - PMBus 6-Channel Power-Supply Manager - Prefixes: 'max34440' - Addresses scanned: - - Datasheet: http://datasheets.maxim-ic.com/en/ds/MAX34440.pdf - * Maxim MAX34441 - PMBus 5-Channel Power-Supply Manager and Intelligent Fan Controller - Prefixes: 'max34441' - Addresses scanned: - - Datasheet: http://datasheets.maxim-ic.com/en/ds/MAX34441.pdf - * Maxim MAX8688 - Digital Power-Supply Controller/Monitor - Prefix: 'max8688' - Addresses scanned: - - Datasheet: http://datasheets.maxim-ic.com/en/ds/MAX8688.pdf * Generic PMBus devices Prefix: 'pmbus' Addresses scanned: - @@ -175,11 +155,13 @@ currX_crit Critical maximum current. From IIN_OC_FAULT_LIMIT or IOUT_OC_FAULT_LIMIT register. currX_alarm Current high alarm. From IIN_OC_WARNING or IOUT_OC_WARNING status. +currX_max_alarm Current high alarm. + From IIN_OC_WARN_LIMIT or IOUT_OC_WARN_LIMIT status. currX_lcrit_alarm Output current critical low alarm. From IOUT_UC_FAULT status. currX_crit_alarm Current critical high alarm. From IIN_OC_FAULT or IOUT_OC_FAULT status. -currX_label "iin" or "vinY" +currX_label "iin" or "ioutY" powerX_input Measured power. From READ_PIN or READ_POUT register. powerX_cap Output power cap. From POUT_MAX register. @@ -193,13 +175,13 @@ powerX_crit_alarm Output power critical high alarm. From POUT_OP_FAULT status. powerX_label "pin" or "poutY" -tempX_input Measured tempererature. +tempX_input Measured temperature. From READ_TEMPERATURE_X register. -tempX_min Mimimum tempererature. From UT_WARN_LIMIT register. -tempX_max Maximum tempererature. From OT_WARN_LIMIT register. -tempX_lcrit Critical low tempererature. +tempX_min Mimimum temperature. From UT_WARN_LIMIT register. +tempX_max Maximum temperature. From OT_WARN_LIMIT register. +tempX_lcrit Critical low temperature. From UT_FAULT_LIMIT register. -tempX_crit Critical high tempererature. +tempX_crit Critical high temperature. From OT_FAULT_LIMIT register. tempX_min_alarm Chip temperature low alarm. Set by comparing READ_TEMPERATURE_X with UT_WARN_LIMIT if diff --git a/Documentation/hwmon/smm665 b/Documentation/hwmon/smm665 index 3820fc9..59e3161 100644 --- a/Documentation/hwmon/smm665 +++ b/Documentation/hwmon/smm665 @@ -150,8 +150,8 @@ in8_crit_alarm Channel F critical alarm in9_crit_alarm AIN1 critical alarm in10_crit_alarm AIN2 critical alarm -temp1_input Chip tempererature -temp1_min Mimimum chip tempererature -temp1_max Maximum chip tempererature -temp1_crit Critical chip tempererature +temp1_input Chip temperature +temp1_min Mimimum chip temperature +temp1_max Maximum chip temperature +temp1_crit Critical chip temperature temp1_crit_alarm Temperature critical alarm diff --git a/Documentation/hwmon/submitting-patches b/Documentation/hwmon/submitting-patches new file mode 100644 index 0000000..86f42e8 --- /dev/null +++ b/Documentation/hwmon/submitting-patches @@ -0,0 +1,109 @@ + How to Get Your Patch Accepted Into the Hwmon Subsystem + ------------------------------------------------------- + +This text is is a collection of suggestions for people writing patches or +drivers for the hwmon subsystem. Following these suggestions will greatly +increase the chances of your change being accepted. + + +1. General +---------- + +* It should be unnecessary to mention, but please read and follow + Documentation/SubmitChecklist + Documentation/SubmittingDrivers + Documentation/SubmittingPatches + Documentation/CodingStyle + +* If your patch generates checkpatch warnings, please refrain from explanations + such as "I don't like that coding style". Keep in mind that each unnecessary + warning helps hiding a real problem. If you don't like the kernel coding + style, don't write kernel drivers. + +* Please test your patch thoroughly. We are not your test group. + Sometimes a patch can not or not completely be tested because of missing + hardware. In such cases, you should test-build the code on at least one + architecture. If run-time testing was not achieved, it should be written + explicitly below the patch header. + +* If your patch (or the driver) is affected by configuration options such as + CONFIG_SMP or CONFIG_HOTPLUG, make sure it compiles for all configuration + variants. + + +2. Adding functionality to existing drivers +------------------------------------------- + +* Make sure the documentation in Documentation/hwmon/<driver_name> is up to + date. + +* Make sure the information in Kconfig is up to date. + +* If the added functionality requires some cleanup or structural changes, split + your patch into a cleanup part and the actual addition. This makes it easier + to review your changes, and to bisect any resulting problems. + +* Never mix bug fixes, cleanup, and functional enhancements in a single patch. + + +3. New drivers +-------------- + +* Running your patch or driver file(s) through checkpatch does not mean its + formatting is clean. If unsure about formatting in your new driver, run it + through Lindent. Lindent is not perfect, and you may have to do some minor + cleanup, but it is a good start. + +* Consider adding yourself to MAINTAINERS. + +* Document the driver in Documentation/hwmon/<driver_name>. + +* Add the driver to Kconfig and Makefile in alphabetical order. + +* Make sure that all dependencies are listed in Kconfig. For new drivers, it + is most likely prudent to add a dependency on EXPERIMENTAL. + +* Avoid forward declarations if you can. Rearrange the code if necessary. + +* Avoid calculations in macros and macro-generated functions. While such macros + may save a line or so in the source, it obfuscates the code and makes code + review more difficult. It may also result in code which is more complicated + than necessary. Use inline functions or just regular functions instead. + +* If the driver has a detect function, make sure it is silent. Debug messages + and messages printed after a successful detection are acceptable, but it + must not print messages such as "Chip XXX not found/supported". + + Keep in mind that the detect function will run for all drivers supporting an + address if a chip is detected on that address. Unnecessary messages will just + pollute the kernel log and not provide any value. + +* Provide a detect function if and only if a chip can be detected reliably. + +* Avoid writing to chip registers in the detect function. If you have to write, + only do it after you have already gathered enough data to be certain that the + detection is going to be successful. + + Keep in mind that the chip might not be what your driver believes it is, and + writing to it might cause a bad misconfiguration. + +* Make sure there are no race conditions in the probe function. Specifically, + completely initialize your chip first, then create sysfs entries and register + with the hwmon subsystem. + +* Do not provide support for deprecated sysfs attributes. + +* Do not create non-standard attributes unless really needed. If you have to use + non-standard attributes, or you believe you do, discuss it on the mailing list + first. Either case, provide a detailed explanation why you need the + non-standard attribute(s). + Standard attributes are specified in Documentation/hwmon/sysfs-interface. + +* When deciding which sysfs attributes to support, look at the chip's + capabilities. While we do not expect your driver to support everything the + chip may offer, it should at least support all limits and alarms. + +* Last but not least, please check if a driver for your chip already exists + before starting to write a new driver. Especially for temperature sensors, + new chips are often variants of previously released chips. In some cases, + a presumably new chip may simply have been relabeled. |