aboutsummaryrefslogtreecommitdiffstats
path: root/arch/x86/kernel/apic_32.c
diff options
context:
space:
mode:
Diffstat (limited to 'arch/x86/kernel/apic_32.c')
-rw-r--r--arch/x86/kernel/apic_32.c1566
1 files changed, 1566 insertions, 0 deletions
diff --git a/arch/x86/kernel/apic_32.c b/arch/x86/kernel/apic_32.c
new file mode 100644
index 0000000..3d67ae1
--- /dev/null
+++ b/arch/x86/kernel/apic_32.c
@@ -0,0 +1,1566 @@
+/*
+ * Local APIC handling, local APIC timers
+ *
+ * (c) 1999, 2000 Ingo Molnar <mingo@redhat.com>
+ *
+ * Fixes
+ * Maciej W. Rozycki : Bits for genuine 82489DX APICs;
+ * thanks to Eric Gilmore
+ * and Rolf G. Tews
+ * for testing these extensively.
+ * Maciej W. Rozycki : Various updates and fixes.
+ * Mikael Pettersson : Power Management for UP-APIC.
+ * Pavel Machek and
+ * Mikael Pettersson : PM converted to driver model.
+ */
+
+#include <linux/init.h>
+
+#include <linux/mm.h>
+#include <linux/delay.h>
+#include <linux/bootmem.h>
+#include <linux/interrupt.h>
+#include <linux/mc146818rtc.h>
+#include <linux/kernel_stat.h>
+#include <linux/sysdev.h>
+#include <linux/cpu.h>
+#include <linux/clockchips.h>
+#include <linux/acpi_pmtmr.h>
+#include <linux/module.h>
+#include <linux/dmi.h>
+
+#include <asm/atomic.h>
+#include <asm/smp.h>
+#include <asm/mtrr.h>
+#include <asm/mpspec.h>
+#include <asm/desc.h>
+#include <asm/arch_hooks.h>
+#include <asm/hpet.h>
+#include <asm/i8253.h>
+#include <asm/nmi.h>
+
+#include <mach_apic.h>
+#include <mach_apicdef.h>
+#include <mach_ipi.h>
+
+#include "io_ports.h"
+
+/*
+ * Sanity check
+ */
+#if (SPURIOUS_APIC_VECTOR & 0x0F) != 0x0F
+# error SPURIOUS_APIC_VECTOR definition error
+#endif
+
+/*
+ * Knob to control our willingness to enable the local APIC.
+ *
+ * -1=force-disable, +1=force-enable
+ */
+static int enable_local_apic __initdata = 0;
+
+/* Local APIC timer verification ok */
+static int local_apic_timer_verify_ok;
+/* Disable local APIC timer from the kernel commandline or via dmi quirk
+ or using CPU MSR check */
+int local_apic_timer_disabled;
+/* Local APIC timer works in C2 */
+int local_apic_timer_c2_ok;
+EXPORT_SYMBOL_GPL(local_apic_timer_c2_ok);
+
+/*
+ * Debug level, exported for io_apic.c
+ */
+int apic_verbosity;
+
+static unsigned int calibration_result;
+
+static int lapic_next_event(unsigned long delta,
+ struct clock_event_device *evt);
+static void lapic_timer_setup(enum clock_event_mode mode,
+ struct clock_event_device *evt);
+static void lapic_timer_broadcast(cpumask_t mask);
+static void apic_pm_activate(void);
+
+/*
+ * The local apic timer can be used for any function which is CPU local.
+ */
+static struct clock_event_device lapic_clockevent = {
+ .name = "lapic",
+ .features = CLOCK_EVT_FEAT_PERIODIC | CLOCK_EVT_FEAT_ONESHOT
+ | CLOCK_EVT_FEAT_C3STOP | CLOCK_EVT_FEAT_DUMMY,
+ .shift = 32,
+ .set_mode = lapic_timer_setup,
+ .set_next_event = lapic_next_event,
+ .broadcast = lapic_timer_broadcast,
+ .rating = 100,
+ .irq = -1,
+};
+static DEFINE_PER_CPU(struct clock_event_device, lapic_events);
+
+/* Local APIC was disabled by the BIOS and enabled by the kernel */
+static int enabled_via_apicbase;
+
+/*
+ * Get the LAPIC version
+ */
+static inline int lapic_get_version(void)
+{
+ return GET_APIC_VERSION(apic_read(APIC_LVR));
+}
+
+/*
+ * Check, if the APIC is integrated or a seperate chip
+ */
+static inline int lapic_is_integrated(void)
+{
+ return APIC_INTEGRATED(lapic_get_version());
+}
+
+/*
+ * Check, whether this is a modern or a first generation APIC
+ */
+static int modern_apic(void)
+{
+ /* AMD systems use old APIC versions, so check the CPU */
+ if (boot_cpu_data.x86_vendor == X86_VENDOR_AMD &&
+ boot_cpu_data.x86 >= 0xf)
+ return 1;
+ return lapic_get_version() >= 0x14;
+}
+
+void apic_wait_icr_idle(void)
+{
+ while (apic_read(APIC_ICR) & APIC_ICR_BUSY)
+ cpu_relax();
+}
+
+unsigned long safe_apic_wait_icr_idle(void)
+{
+ unsigned long send_status;
+ int timeout;
+
+ timeout = 0;
+ do {
+ send_status = apic_read(APIC_ICR) & APIC_ICR_BUSY;
+ if (!send_status)
+ break;
+ udelay(100);
+ } while (timeout++ < 1000);
+
+ return send_status;
+}
+
+/**
+ * enable_NMI_through_LVT0 - enable NMI through local vector table 0
+ */
+void enable_NMI_through_LVT0 (void * dummy)
+{
+ unsigned int v = APIC_DM_NMI;
+
+ /* Level triggered for 82489DX */
+ if (!lapic_is_integrated())
+ v |= APIC_LVT_LEVEL_TRIGGER;
+ apic_write_around(APIC_LVT0, v);
+}
+
+/**
+ * get_physical_broadcast - Get number of physical broadcast IDs
+ */
+int get_physical_broadcast(void)
+{
+ return modern_apic() ? 0xff : 0xf;
+}
+
+/**
+ * lapic_get_maxlvt - get the maximum number of local vector table entries
+ */
+int lapic_get_maxlvt(void)
+{
+ unsigned int v = apic_read(APIC_LVR);
+
+ /* 82489DXs do not report # of LVT entries. */
+ return APIC_INTEGRATED(GET_APIC_VERSION(v)) ? GET_APIC_MAXLVT(v) : 2;
+}
+
+/*
+ * Local APIC timer
+ */
+
+/* Clock divisor is set to 16 */
+#define APIC_DIVISOR 16
+
+/*
+ * This function sets up the local APIC timer, with a timeout of
+ * 'clocks' APIC bus clock. During calibration we actually call
+ * this function twice on the boot CPU, once with a bogus timeout
+ * value, second time for real. The other (noncalibrating) CPUs
+ * call this function only once, with the real, calibrated value.
+ *
+ * We do reads before writes even if unnecessary, to get around the
+ * P5 APIC double write bug.
+ */
+static void __setup_APIC_LVTT(unsigned int clocks, int oneshot, int irqen)
+{
+ unsigned int lvtt_value, tmp_value;
+
+ lvtt_value = LOCAL_TIMER_VECTOR;
+ if (!oneshot)
+ lvtt_value |= APIC_LVT_TIMER_PERIODIC;
+ if (!lapic_is_integrated())
+ lvtt_value |= SET_APIC_TIMER_BASE(APIC_TIMER_BASE_DIV);
+
+ if (!irqen)
+ lvtt_value |= APIC_LVT_MASKED;
+
+ apic_write_around(APIC_LVTT, lvtt_value);
+
+ /*
+ * Divide PICLK by 16
+ */
+ tmp_value = apic_read(APIC_TDCR);
+ apic_write_around(APIC_TDCR, (tmp_value
+ & ~(APIC_TDR_DIV_1 | APIC_TDR_DIV_TMBASE))
+ | APIC_TDR_DIV_16);
+
+ if (!oneshot)
+ apic_write_around(APIC_TMICT, clocks/APIC_DIVISOR);
+}
+
+/*
+ * Program the next event, relative to now
+ */
+static int lapic_next_event(unsigned long delta,
+ struct clock_event_device *evt)
+{
+ apic_write_around(APIC_TMICT, delta);
+ return 0;
+}
+
+/*
+ * Setup the lapic timer in periodic or oneshot mode
+ */
+static void lapic_timer_setup(enum clock_event_mode mode,
+ struct clock_event_device *evt)
+{
+ unsigned long flags;
+ unsigned int v;
+
+ /* Lapic used for broadcast ? */
+ if (!local_apic_timer_verify_ok)
+ return;
+
+ local_irq_save(flags);
+
+ switch (mode) {
+ case CLOCK_EVT_MODE_PERIODIC:
+ case CLOCK_EVT_MODE_ONESHOT:
+ __setup_APIC_LVTT(calibration_result,
+ mode != CLOCK_EVT_MODE_PERIODIC, 1);
+ break;
+ case CLOCK_EVT_MODE_UNUSED:
+ case CLOCK_EVT_MODE_SHUTDOWN:
+ v = apic_read(APIC_LVTT);
+ v |= (APIC_LVT_MASKED | LOCAL_TIMER_VECTOR);
+ apic_write_around(APIC_LVTT, v);
+ break;
+ case CLOCK_EVT_MODE_RESUME:
+ /* Nothing to do here */
+ break;
+ }
+
+ local_irq_restore(flags);
+}
+
+/*
+ * Local APIC timer broadcast function
+ */
+static void lapic_timer_broadcast(cpumask_t mask)
+{
+#ifdef CONFIG_SMP
+ send_IPI_mask(mask, LOCAL_TIMER_VECTOR);
+#endif
+}
+
+/*
+ * Setup the local APIC timer for this CPU. Copy the initilized values
+ * of the boot CPU and register the clock event in the framework.
+ */
+static void __devinit setup_APIC_timer(void)
+{
+ struct clock_event_device *levt = &__get_cpu_var(lapic_events);
+
+ memcpy(levt, &lapic_clockevent, sizeof(*levt));
+ levt->cpumask = cpumask_of_cpu(smp_processor_id());
+
+ clockevents_register_device(levt);
+}
+
+/*
+ * In this functions we calibrate APIC bus clocks to the external timer.
+ *
+ * We want to do the calibration only once since we want to have local timer
+ * irqs syncron. CPUs connected by the same APIC bus have the very same bus
+ * frequency.
+ *
+ * This was previously done by reading the PIT/HPET and waiting for a wrap
+ * around to find out, that a tick has elapsed. I have a box, where the PIT
+ * readout is broken, so it never gets out of the wait loop again. This was
+ * also reported by others.
+ *
+ * Monitoring the jiffies value is inaccurate and the clockevents
+ * infrastructure allows us to do a simple substitution of the interrupt
+ * handler.
+ *
+ * The calibration routine also uses the pm_timer when possible, as the PIT
+ * happens to run way too slow (factor 2.3 on my VAIO CoreDuo, which goes
+ * back to normal later in the boot process).
+ */
+
+#define LAPIC_CAL_LOOPS (HZ/10)
+
+static __initdata int lapic_cal_loops = -1;
+static __initdata long lapic_cal_t1, lapic_cal_t2;
+static __initdata unsigned long long lapic_cal_tsc1, lapic_cal_tsc2;
+static __initdata unsigned long lapic_cal_pm1, lapic_cal_pm2;
+static __initdata unsigned long lapic_cal_j1, lapic_cal_j2;
+
+/*
+ * Temporary interrupt handler.
+ */
+static void __init lapic_cal_handler(struct clock_event_device *dev)
+{
+ unsigned long long tsc = 0;
+ long tapic = apic_read(APIC_TMCCT);
+ unsigned long pm = acpi_pm_read_early();
+
+ if (cpu_has_tsc)
+ rdtscll(tsc);
+
+ switch (lapic_cal_loops++) {
+ case 0:
+ lapic_cal_t1 = tapic;
+ lapic_cal_tsc1 = tsc;
+ lapic_cal_pm1 = pm;
+ lapic_cal_j1 = jiffies;
+ break;
+
+ case LAPIC_CAL_LOOPS:
+ lapic_cal_t2 = tapic;
+ lapic_cal_tsc2 = tsc;
+ if (pm < lapic_cal_pm1)
+ pm += ACPI_PM_OVRRUN;
+ lapic_cal_pm2 = pm;
+ lapic_cal_j2 = jiffies;
+ break;
+ }
+}
+
+/*
+ * Setup the boot APIC
+ *
+ * Calibrate and verify the result.
+ */
+void __init setup_boot_APIC_clock(void)
+{
+ struct clock_event_device *levt = &__get_cpu_var(lapic_events);
+ const long pm_100ms = PMTMR_TICKS_PER_SEC/10;
+ const long pm_thresh = pm_100ms/100;
+ void (*real_handler)(struct clock_event_device *dev);
+ unsigned long deltaj;
+ long delta, deltapm;
+ int pm_referenced = 0;
+
+ /*
+ * The local apic timer can be disabled via the kernel
+ * commandline or from the CPU detection code. Register the lapic
+ * timer as a dummy clock event source on SMP systems, so the
+ * broadcast mechanism is used. On UP systems simply ignore it.
+ */
+ if (local_apic_timer_disabled) {
+ /* No broadcast on UP ! */
+ if (num_possible_cpus() > 1)
+ setup_APIC_timer();
+ return;
+ }
+
+ apic_printk(APIC_VERBOSE, "Using local APIC timer interrupts.\n"
+ "calibrating APIC timer ...\n");
+
+ local_irq_disable();
+
+ /* Replace the global interrupt handler */
+ real_handler = global_clock_event->event_handler;
+ global_clock_event->event_handler = lapic_cal_handler;
+
+ /*
+ * Setup the APIC counter to 1e9. There is no way the lapic
+ * can underflow in the 100ms detection time frame
+ */
+ __setup_APIC_LVTT(1000000000, 0, 0);
+
+ /* Let the interrupts run */
+ local_irq_enable();
+
+ while (lapic_cal_loops <= LAPIC_CAL_LOOPS)
+ cpu_relax();
+
+ local_irq_disable();
+
+ /* Restore the real event handler */
+ global_clock_event->event_handler = real_handler;
+
+ /* Build delta t1-t2 as apic timer counts down */
+ delta = lapic_cal_t1 - lapic_cal_t2;
+ apic_printk(APIC_VERBOSE, "... lapic delta = %ld\n", delta);
+
+ /* Check, if the PM timer is available */
+ deltapm = lapic_cal_pm2 - lapic_cal_pm1;
+ apic_printk(APIC_VERBOSE, "... PM timer delta = %ld\n", deltapm);
+
+ if (deltapm) {
+ unsigned long mult;
+ u64 res;
+
+ mult = clocksource_hz2mult(PMTMR_TICKS_PER_SEC, 22);
+
+ if (deltapm > (pm_100ms - pm_thresh) &&
+ deltapm < (pm_100ms + pm_thresh)) {
+ apic_printk(APIC_VERBOSE, "... PM timer result ok\n");
+ } else {
+ res = (((u64) deltapm) * mult) >> 22;
+ do_div(res, 1000000);
+ printk(KERN_WARNING "APIC calibration not consistent "
+ "with PM Timer: %ldms instead of 100ms\n",
+ (long)res);
+ /* Correct the lapic counter value */
+ res = (((u64) delta ) * pm_100ms);
+ do_div(res, deltapm);
+ printk(KERN_INFO "APIC delta adjusted to PM-Timer: "
+ "%lu (%ld)\n", (unsigned long) res, delta);
+ delta = (long) res;
+ }
+ pm_referenced = 1;
+ }
+
+ /* Calculate the scaled math multiplication factor */
+ lapic_clockevent.mult = div_sc(delta, TICK_NSEC * LAPIC_CAL_LOOPS, 32);
+ lapic_clockevent.max_delta_ns =
+ clockevent_delta2ns(0x7FFFFF, &lapic_clockevent);
+ lapic_clockevent.min_delta_ns =
+ clockevent_delta2ns(0xF, &lapic_clockevent);
+
+ calibration_result = (delta * APIC_DIVISOR) / LAPIC_CAL_LOOPS;
+
+ apic_printk(APIC_VERBOSE, "..... delta %ld\n", delta);
+ apic_printk(APIC_VERBOSE, "..... mult: %ld\n", lapic_clockevent.mult);
+ apic_printk(APIC_VERBOSE, "..... calibration result: %u\n",
+ calibration_result);
+
+ if (cpu_has_tsc) {
+ delta = (long)(lapic_cal_tsc2 - lapic_cal_tsc1);
+ apic_printk(APIC_VERBOSE, "..... CPU clock speed is "
+ "%ld.%04ld MHz.\n",
+ (delta / LAPIC_CAL_LOOPS) / (1000000 / HZ),
+ (delta / LAPIC_CAL_LOOPS) % (1000000 / HZ));
+ }
+
+ apic_printk(APIC_VERBOSE, "..... host bus clock speed is "
+ "%u.%04u MHz.\n",
+ calibration_result / (1000000 / HZ),
+ calibration_result % (1000000 / HZ));
+
+ local_apic_timer_verify_ok = 1;
+
+ /* We trust the pm timer based calibration */
+ if (!pm_referenced) {
+ apic_printk(APIC_VERBOSE, "... verify APIC timer\n");
+
+ /*
+ * Setup the apic timer manually
+ */
+ levt->event_handler = lapic_cal_handler;
+ lapic_timer_setup(CLOCK_EVT_MODE_PERIODIC, levt);
+ lapic_cal_loops = -1;
+
+ /* Let the interrupts run */
+ local_irq_enable();
+
+ while (lapic_cal_loops <= LAPIC_CAL_LOOPS)
+ cpu_relax();
+
+ local_irq_disable();
+
+ /* Stop the lapic timer */
+ lapic_timer_setup(CLOCK_EVT_MODE_SHUTDOWN, levt);
+
+ local_irq_enable();
+
+ /* Jiffies delta */
+ deltaj = lapic_cal_j2 - lapic_cal_j1;
+ apic_printk(APIC_VERBOSE, "... jiffies delta = %lu\n", deltaj);
+
+ /* Check, if the jiffies result is consistent */
+ if (deltaj >= LAPIC_CAL_LOOPS-2 && deltaj <= LAPIC_CAL_LOOPS+2)
+ apic_printk(APIC_VERBOSE, "... jiffies result ok\n");
+ else
+ local_apic_timer_verify_ok = 0;
+ } else
+ local_irq_enable();
+
+ if (!local_apic_timer_verify_ok) {
+ printk(KERN_WARNING
+ "APIC timer disabled due to verification failure.\n");
+ /* No broadcast on UP ! */
+ if (num_possible_cpus() == 1)
+ return;
+ } else {
+ /*
+ * If nmi_watchdog is set to IO_APIC, we need the
+ * PIT/HPET going. Otherwise register lapic as a dummy
+ * device.
+ */
+ if (nmi_watchdog != NMI_IO_APIC)
+ lapic_clockevent.features &= ~CLOCK_EVT_FEAT_DUMMY;
+ else
+ printk(KERN_WARNING "APIC timer registered as dummy,"
+ " due to nmi_watchdog=1!\n");
+ }
+
+ /* Setup the lapic or request the broadcast */
+ setup_APIC_timer();
+}
+
+void __devinit setup_secondary_APIC_clock(void)
+{
+ setup_APIC_timer();
+}
+
+/*
+ * The guts of the apic timer interrupt
+ */
+static void local_apic_timer_interrupt(void)
+{
+ int cpu = smp_processor_id();
+ struct clock_event_device *evt = &per_cpu(lapic_events, cpu);
+
+ /*
+ * Normally we should not be here till LAPIC has been initialized but
+ * in some cases like kdump, its possible that there is a pending LAPIC
+ * timer interrupt from previous kernel's context and is delivered in
+ * new kernel the moment interrupts are enabled.
+ *
+ * Interrupts are enabled early and LAPIC is setup much later, hence
+ * its possible that when we get here evt->event_handler is NULL.
+ * Check for event_handler being NULL and discard the interrupt as
+ * spurious.
+ */
+ if (!evt->event_handler) {
+ printk(KERN_WARNING
+ "Spurious LAPIC timer interrupt on cpu %d\n", cpu);
+ /* Switch it off */
+ lapic_timer_setup(CLOCK_EVT_MODE_SHUTDOWN, evt);
+ return;
+ }
+
+ per_cpu(irq_stat, cpu).apic_timer_irqs++;
+
+ evt->event_handler(evt);
+}
+
+/*
+ * Local APIC timer interrupt. This is the most natural way for doing
+ * local interrupts, but local timer interrupts can be emulated by
+ * broadcast interrupts too. [in case the hw doesn't support APIC timers]
+ *
+ * [ if a single-CPU system runs an SMP kernel then we call the local
+ * interrupt as well. Thus we cannot inline the local irq ... ]
+ */
+
+void fastcall smp_apic_timer_interrupt(struct pt_regs *regs)
+{
+ struct pt_regs *old_regs = set_irq_regs(regs);
+
+ /*
+ * NOTE! We'd better ACK the irq immediately,
+ * because timer handling can be slow.
+ */
+ ack_APIC_irq();
+ /*
+ * update_process_times() expects us to have done irq_enter().
+ * Besides, if we don't timer interrupts ignore the global
+ * interrupt lock, which is the WrongThing (tm) to do.
+ */
+ irq_enter();
+ local_apic_timer_interrupt();
+ irq_exit();
+
+ set_irq_regs(old_regs);
+}
+
+int setup_profiling_timer(unsigned int multiplier)
+{
+ return -EINVAL;
+}
+
+/*
+ * Local APIC start and shutdown
+ */
+
+/**
+ * clear_local_APIC - shutdown the local APIC
+ *
+ * This is called, when a CPU is disabled and before rebooting, so the state of
+ * the local APIC has no dangling leftovers. Also used to cleanout any BIOS
+ * leftovers during boot.
+ */
+void clear_local_APIC(void)
+{
+ int maxlvt = lapic_get_maxlvt();
+ unsigned long v;
+
+ /*
+ * Masking an LVT entry can trigger a local APIC error
+ * if the vector is zero. Mask LVTERR first to prevent this.
+ */
+ if (maxlvt >= 3) {
+ v = ERROR_APIC_VECTOR; /* any non-zero vector will do */
+ apic_write_around(APIC_LVTERR, v | APIC_LVT_MASKED);
+ }
+ /*
+ * Careful: we have to set masks only first to deassert
+ * any level-triggered sources.
+ */
+ v = apic_read(APIC_LVTT);
+ apic_write_around(APIC_LVTT, v | APIC_LVT_MASKED);
+ v = apic_read(APIC_LVT0);
+ apic_write_around(APIC_LVT0, v | APIC_LVT_MASKED);
+ v = apic_read(APIC_LVT1);
+ apic_write_around(APIC_LVT1, v | APIC_LVT_MASKED);
+ if (maxlvt >= 4) {
+ v = apic_read(APIC_LVTPC);
+ apic_write_around(APIC_LVTPC, v | APIC_LVT_MASKED);
+ }
+
+ /* lets not touch this if we didn't frob it */
+#ifdef CONFIG_X86_MCE_P4THERMAL
+ if (maxlvt >= 5) {
+ v = apic_read(APIC_LVTTHMR);
+ apic_write_around(APIC_LVTTHMR, v | APIC_LVT_MASKED);
+ }
+#endif
+ /*
+ * Clean APIC state for other OSs:
+ */
+ apic_write_around(APIC_LVTT, APIC_LVT_MASKED);
+ apic_write_around(APIC_LVT0, APIC_LVT_MASKED);
+ apic_write_around(APIC_LVT1, APIC_LVT_MASKED);
+ if (maxlvt >= 3)
+ apic_write_around(APIC_LVTERR, APIC_LVT_MASKED);
+ if (maxlvt >= 4)
+ apic_write_around(APIC_LVTPC, APIC_LVT_MASKED);
+
+#ifdef CONFIG_X86_MCE_P4THERMAL
+ if (maxlvt >= 5)
+ apic_write_around(APIC_LVTTHMR, APIC_LVT_MASKED);
+#endif
+ /* Integrated APIC (!82489DX) ? */
+ if (lapic_is_integrated()) {
+ if (maxlvt > 3)
+ /* Clear ESR due to Pentium errata 3AP and 11AP */
+ apic_write(APIC_ESR, 0);
+ apic_read(APIC_ESR);
+ }
+}
+
+/**
+ * disable_local_APIC - clear and disable the local APIC
+ */
+void disable_local_APIC(void)
+{
+ unsigned long value;
+
+ clear_local_APIC();
+
+ /*
+ * Disable APIC (implies clearing of registers
+ * for 82489DX!).
+ */
+ value = apic_read(APIC_SPIV);
+ value &= ~APIC_SPIV_APIC_ENABLED;
+ apic_write_around(APIC_SPIV, value);
+
+ /*
+ * When LAPIC was disabled by the BIOS and enabled by the kernel,
+ * restore the disabled state.
+ */
+ if (enabled_via_apicbase) {
+ unsigned int l, h;
+
+ rdmsr(MSR_IA32_APICBASE, l, h);
+ l &= ~MSR_IA32_APICBASE_ENABLE;
+ wrmsr(MSR_IA32_APICBASE, l, h);
+ }
+}
+
+/*
+ * If Linux enabled the LAPIC against the BIOS default disable it down before
+ * re-entering the BIOS on shutdown. Otherwise the BIOS may get confused and
+ * not power-off. Additionally clear all LVT entries before disable_local_APIC
+ * for the case where Linux didn't enable the LAPIC.
+ */
+void lapic_shutdown(void)
+{
+ unsigned long flags;
+
+ if (!cpu_has_apic)
+ return;
+
+ local_irq_save(flags);
+ clear_local_APIC();
+
+ if (enabled_via_apicbase)
+ disable_local_APIC();
+
+ local_irq_restore(flags);
+}
+
+/*
+ * This is to verify that we're looking at a real local APIC.
+ * Check these against your board if the CPUs aren't getting
+ * started for no apparent reason.
+ */
+int __init verify_local_APIC(void)
+{
+ unsigned int reg0, reg1;
+
+ /*
+ * The version register is read-only in a real APIC.
+ */
+ reg0 = apic_read(APIC_LVR);
+ apic_printk(APIC_DEBUG, "Getting VERSION: %x\n", reg0);
+ apic_write(APIC_LVR, reg0 ^ APIC_LVR_MASK);
+ reg1 = apic_read(APIC_LVR);
+ apic_printk(APIC_DEBUG, "Getting VERSION: %x\n", reg1);
+
+ /*
+ * The two version reads above should print the same
+ * numbers. If the second one is different, then we
+ * poke at a non-APIC.
+ */
+ if (reg1 != reg0)
+ return 0;
+
+ /*
+ * Check if the version looks reasonably.
+ */
+ reg1 = GET_APIC_VERSION(reg0);
+ if (reg1 == 0x00 || reg1 == 0xff)
+ return 0;
+ reg1 = lapic_get_maxlvt();
+ if (reg1 < 0x02 || reg1 == 0xff)
+ return 0;
+
+ /*
+ * The ID register is read/write in a real APIC.
+ */
+ reg0 = apic_read(APIC_ID);
+ apic_printk(APIC_DEBUG, "Getting ID: %x\n", reg0);
+
+ /*
+ * The next two are just to see if we have sane values.
+ * They're only really relevant if we're in Virtual Wire
+ * compatibility mode, but most boxes are anymore.
+ */
+ reg0 = apic_read(APIC_LVT0);
+ apic_printk(APIC_DEBUG, "Getting LVT0: %x\n", reg0);
+ reg1 = apic_read(APIC_LVT1);
+ apic_printk(APIC_DEBUG, "Getting LVT1: %x\n", reg1);
+
+ return 1;
+}
+
+/**
+ * sync_Arb_IDs - synchronize APIC bus arbitration IDs
+ */
+void __init sync_Arb_IDs(void)
+{
+ /*
+ * Unsupported on P4 - see Intel Dev. Manual Vol. 3, Ch. 8.6.1 And not
+ * needed on AMD.
+ */
+ if (modern_apic())
+ return;
+ /*
+ * Wait for idle.
+ */
+ apic_wait_icr_idle();
+
+ apic_printk(APIC_DEBUG, "Synchronizing Arb IDs.\n");
+ apic_write_around(APIC_ICR, APIC_DEST_ALLINC | APIC_INT_LEVELTRIG
+ | APIC_DM_INIT);
+}
+
+/*
+ * An initial setup of the virtual wire mode.
+ */
+void __init init_bsp_APIC(void)
+{
+ unsigned long value;
+
+ /*
+ * Don't do the setup now if we have a SMP BIOS as the
+ * through-I/O-APIC virtual wire mode might be active.
+ */
+ if (smp_found_config || !cpu_has_apic)
+ return;
+
+ /*
+ * Do not trust the local APIC being empty at bootup.
+ */
+ clear_local_APIC();
+
+ /*
+ * Enable APIC.
+ */
+ value = apic_read(APIC_SPIV);
+ value &= ~APIC_VECTOR_MASK;
+ value |= APIC_SPIV_APIC_ENABLED;
+
+ /* This bit is reserved on P4/Xeon and should be cleared */
+ if ((boot_cpu_data.x86_vendor == X86_VENDOR_INTEL) &&
+ (boot_cpu_data.x86 == 15))
+ value &= ~APIC_SPIV_FOCUS_DISABLED;
+ else
+ value |= APIC_SPIV_FOCUS_DISABLED;
+ value |= SPURIOUS_APIC_VECTOR;
+ apic_write_around(APIC_SPIV, value);
+
+ /*
+ * Set up the virtual wire mode.
+ */
+ apic_write_around(APIC_LVT0, APIC_DM_EXTINT);
+ value = APIC_DM_NMI;
+ if (!lapic_is_integrated()) /* 82489DX */
+ value |= APIC_LVT_LEVEL_TRIGGER;
+ apic_write_around(APIC_LVT1, value);
+}
+
+/**
+ * setup_local_APIC - setup the local APIC
+ */
+void __devinit setup_local_APIC(void)
+{
+ unsigned long oldvalue, value, maxlvt, integrated;
+ int i, j;
+
+ /* Pound the ESR really hard over the head with a big hammer - mbligh */
+ if (esr_disable) {
+ apic_write(APIC_ESR, 0);
+ apic_write(APIC_ESR, 0);
+ apic_write(APIC_ESR, 0);
+ apic_write(APIC_ESR, 0);
+ }
+
+ integrated = lapic_is_integrated();
+
+ /*
+ * Double-check whether this APIC is really registered.
+ */
+ if (!apic_id_registered())
+ BUG();
+
+ /*
+ * Intel recommends to set DFR, LDR and TPR before enabling
+ * an APIC. See e.g. "AP-388 82489DX User's Manual" (Intel
+ * document number 292116). So here it goes...
+ */
+ init_apic_ldr();
+
+ /*
+ * Set Task Priority to 'accept all'. We never change this
+ * later on.
+ */
+ value = apic_read(APIC_TASKPRI);
+ value &= ~APIC_TPRI_MASK;
+ apic_write_around(APIC_TASKPRI, value);
+
+ /*
+ * After a crash, we no longer service the interrupts and a pending
+ * interrupt from previous kernel might still have ISR bit set.
+ *
+ * Most probably by now CPU has serviced that pending interrupt and
+ * it might not have done the ack_APIC_irq() because it thought,
+ * interrupt came from i8259 as ExtInt. LAPIC did not get EOI so it
+ * does not clear the ISR bit and cpu thinks it has already serivced
+ * the interrupt. Hence a vector might get locked. It was noticed
+ * for timer irq (vector 0x31). Issue an extra EOI to clear ISR.
+ */
+ for (i = APIC_ISR_NR - 1; i >= 0; i--) {
+ value = apic_read(APIC_ISR + i*0x10);
+ for (j = 31; j >= 0; j--) {
+ if (value & (1<<j))
+ ack_APIC_irq();
+ }
+ }
+
+ /*
+ * Now that we are all set up, enable the APIC
+ */
+ value = apic_read(APIC_SPIV);
+ value &= ~APIC_VECTOR_MASK;
+ /*
+ * Enable APIC
+ */
+ value |= APIC_SPIV_APIC_ENABLED;
+
+ /*
+ * Some unknown Intel IO/APIC (or APIC) errata is biting us with
+ * certain networking cards. If high frequency interrupts are
+ * happening on a particular IOAPIC pin, plus the IOAPIC routing
+ * entry is masked/unmasked at a high rate as well then sooner or
+ * later IOAPIC line gets 'stuck', no more interrupts are received
+ * from the device. If focus CPU is disabled then the hang goes
+ * away, oh well :-(
+ *
+ * [ This bug can be reproduced easily with a level-triggered
+ * PCI Ne2000 networking cards and PII/PIII processors, dual
+ * BX chipset. ]
+ */
+ /*
+ * Actually disabling the focus CPU check just makes the hang less
+ * frequent as it makes the interrupt distributon model be more
+ * like LRU than MRU (the short-term load is more even across CPUs).
+ * See also the comment in end_level_ioapic_irq(). --macro
+ */
+
+ /* Enable focus processor (bit==0) */
+ value &= ~APIC_SPIV_FOCUS_DISABLED;
+
+ /*
+ * Set spurious IRQ vector
+ */
+ value |= SPURIOUS_APIC_VECTOR;
+ apic_write_around(APIC_SPIV, value);
+
+ /*
+ * Set up LVT0, LVT1:
+ *
+ * set up through-local-APIC on the BP's LINT0. This is not
+ * strictly necessery in pure symmetric-IO mode, but sometimes
+ * we delegate interrupts to the 8259A.
+ */
+ /*
+ * TODO: set up through-local-APIC from through-I/O-APIC? --macro
+ */
+ value = apic_read(APIC_LVT0) & APIC_LVT_MASKED;
+ if (!smp_processor_id() && (pic_mode || !value)) {
+ value = APIC_DM_EXTINT;
+ apic_printk(APIC_VERBOSE, "enabled ExtINT on CPU#%d\n",
+ smp_processor_id());
+ } else {
+ value = APIC_DM_EXTINT | APIC_LVT_MASKED;
+ apic_printk(APIC_VERBOSE, "masked ExtINT on CPU#%d\n",
+ smp_processor_id());
+ }
+ apic_write_around(APIC_LVT0, value);
+
+ /*
+ * only the BP should see the LINT1 NMI signal, obviously.
+ */
+ if (!smp_processor_id())
+ value = APIC_DM_NMI;
+ else
+ value = APIC_DM_NMI | APIC_LVT_MASKED;
+ if (!integrated) /* 82489DX */
+ value |= APIC_LVT_LEVEL_TRIGGER;
+ apic_write_around(APIC_LVT1, value);
+
+ if (integrated && !esr_disable) { /* !82489DX */
+ maxlvt = lapic_get_maxlvt();
+ if (maxlvt > 3) /* Due to the Pentium erratum 3AP. */
+ apic_write(APIC_ESR, 0);
+ oldvalue = apic_read(APIC_ESR);
+
+ /* enables sending errors */
+ value = ERROR_APIC_VECTOR;
+ apic_write_around(APIC_LVTERR, value);
+ /*
+ * spec says clear errors after enabling vector.
+ */
+ if (maxlvt > 3)
+ apic_write(APIC_ESR, 0);
+ value = apic_read(APIC_ESR);
+ if (value != oldvalue)
+ apic_printk(APIC_VERBOSE, "ESR value before enabling "
+ "vector: 0x%08lx after: 0x%08lx\n",
+ oldvalue, value);
+ } else {
+ if (esr_disable)
+ /*
+ * Something untraceble is creating bad interrupts on
+ * secondary quads ... for the moment, just leave the
+ * ESR disabled - we can't do anything useful with the
+ * errors anyway - mbligh
+ */
+ printk(KERN_INFO "Leaving ESR disabled.\n");
+ else
+ printk(KERN_INFO "No ESR for 82489DX.\n");
+ }
+
+ /* Disable the local apic timer */
+ value = apic_read(APIC_LVTT);
+ value |= (APIC_LVT_MASKED | LOCAL_TIMER_VECTOR);
+ apic_write_around(APIC_LVTT, value);
+
+ setup_apic_nmi_watchdog(NULL);
+ apic_pm_activate();
+}
+
+/*
+ * Detect and initialize APIC
+ */
+static int __init detect_init_APIC (void)
+{
+ u32 h, l, features;
+
+ /* Disabled by kernel option? */
+ if (enable_local_apic < 0)
+ return -1;
+
+ switch (boot_cpu_data.x86_vendor) {
+ case X86_VENDOR_AMD:
+ if ((boot_cpu_data.x86 == 6 && boot_cpu_data.x86_model > 1) ||
+ (boot_cpu_data.x86 == 15))
+ break;
+ goto no_apic;
+ case X86_VENDOR_INTEL:
+ if (boot_cpu_data.x86 == 6 || boot_cpu_data.x86 == 15 ||
+ (boot_cpu_data.x86 == 5 && cpu_has_apic))
+ break;
+ goto no_apic;
+ default:
+ goto no_apic;
+ }
+
+ if (!cpu_has_apic) {
+ /*
+ * Over-ride BIOS and try to enable the local APIC only if
+ * "lapic" specified.
+ */
+ if (enable_local_apic <= 0) {
+ printk(KERN_INFO "Local APIC disabled by BIOS -- "
+ "you can enable it with \"lapic\"\n");
+ return -1;
+ }
+ /*
+ * Some BIOSes disable the local APIC in the APIC_BASE
+ * MSR. This can only be done in software for Intel P6 or later
+ * and AMD K7 (Model > 1) or later.
+ */
+ rdmsr(MSR_IA32_APICBASE, l, h);
+ if (!(l & MSR_IA32_APICBASE_ENABLE)) {
+ printk(KERN_INFO
+ "Local APIC disabled by BIOS -- reenabling.\n");
+ l &= ~MSR_IA32_APICBASE_BASE;
+ l |= MSR_IA32_APICBASE_ENABLE | APIC_DEFAULT_PHYS_BASE;
+ wrmsr(MSR_IA32_APICBASE, l, h);
+ enabled_via_apicbase = 1;
+ }
+ }
+ /*
+ * The APIC feature bit should now be enabled
+ * in `cpuid'
+ */
+ features = cpuid_edx(1);
+ if (!(features & (1 << X86_FEATURE_APIC))) {
+ printk(KERN_WARNING "Could not enable APIC!\n");
+ return -1;
+ }
+ set_bit(X86_FEATURE_APIC, boot_cpu_data.x86_capability);
+ mp_lapic_addr = APIC_DEFAULT_PHYS_BASE;
+
+ /* The BIOS may have set up the APIC at some other address */
+ rdmsr(MSR_IA32_APICBASE, l, h);
+ if (l & MSR_IA32_APICBASE_ENABLE)
+ mp_lapic_addr = l & MSR_IA32_APICBASE_BASE;
+
+ if (nmi_watchdog != NMI_NONE && nmi_watchdog != NMI_DISABLED)
+ nmi_watchdog = NMI_LOCAL_APIC;
+
+ printk(KERN_INFO "Found and enabled local APIC!\n");
+
+ apic_pm_activate();
+
+ return 0;
+
+no_apic:
+ printk(KERN_INFO "No local APIC present or hardware disabled\n");
+ return -1;
+}
+
+/**
+ * init_apic_mappings - initialize APIC mappings
+ */
+void __init init_apic_mappings(void)
+{
+ unsigned long apic_phys;
+
+ /*
+ * If no local APIC can be found then set up a fake all
+ * zeroes page to simulate the local APIC and another
+ * one for the IO-APIC.
+ */
+ if (!smp_found_config && detect_init_APIC()) {
+ apic_phys = (unsigned long) alloc_bootmem_pages(PAGE_SIZE);
+ apic_phys = __pa(apic_phys);
+ } else
+ apic_phys = mp_lapic_addr;
+
+ set_fixmap_nocache(FIX_APIC_BASE, apic_phys);
+ printk(KERN_DEBUG "mapped APIC to %08lx (%08lx)\n", APIC_BASE,
+ apic_phys);
+
+ /*
+ * Fetch the APIC ID of the BSP in case we have a
+ * default configuration (or the MP table is broken).
+ */
+ if (boot_cpu_physical_apicid == -1U)
+ boot_cpu_physical_apicid = GET_APIC_ID(apic_read(APIC_ID));
+
+#ifdef CONFIG_X86_IO_APIC
+ {
+ unsigned long ioapic_phys, idx = FIX_IO_APIC_BASE_0;
+ int i;
+
+ for (i = 0; i < nr_ioapics; i++) {
+ if (smp_found_config) {
+ ioapic_phys = mp_ioapics[i].mpc_apicaddr;
+ if (!ioapic_phys) {
+ printk(KERN_ERR
+ "WARNING: bogus zero IO-APIC "
+ "address found in MPTABLE, "
+ "disabling IO/APIC support!\n");
+ smp_found_config = 0;
+ skip_ioapic_setup = 1;
+ goto fake_ioapic_page;
+ }
+ } else {
+fake_ioapic_page:
+ ioapic_phys = (unsigned long)
+ alloc_bootmem_pages(PAGE_SIZE);
+ ioapic_phys = __pa(ioapic_phys);
+ }
+ set_fixmap_nocache(idx, ioapic_phys);
+ printk(KERN_DEBUG "mapped IOAPIC to %08lx (%08lx)\n",
+ __fix_to_virt(idx), ioapic_phys);
+ idx++;
+ }
+ }
+#endif
+}
+
+/*
+ * This initializes the IO-APIC and APIC hardware if this is
+ * a UP kernel.
+ */
+int __init APIC_init_uniprocessor (void)
+{
+ if (enable_local_apic < 0)
+ clear_bit(X86_FEATURE_APIC, boot_cpu_data.x86_capability);
+
+ if (!smp_found_config && !cpu_has_apic)
+ return -1;
+
+ /*
+ * Complain if the BIOS pretends there is one.
+ */
+ if (!cpu_has_apic &&
+ APIC_INTEGRATED(apic_version[boot_cpu_physical_apicid])) {
+ printk(KERN_ERR "BIOS bug, local APIC #%d not detected!...\n",
+ boot_cpu_physical_apicid);
+ clear_bit(X86_FEATURE_APIC, boot_cpu_data.x86_capability);
+ return -1;
+ }
+
+ verify_local_APIC();
+
+ connect_bsp_APIC();
+
+ /*
+ * Hack: In case of kdump, after a crash, kernel might be booting
+ * on a cpu with non-zero lapic id. But boot_cpu_physical_apicid
+ * might be zero if read from MP tables. Get it from LAPIC.
+ */
+#ifdef CONFIG_CRASH_DUMP
+ boot_cpu_physical_apicid = GET_APIC_ID(apic_read(APIC_ID));
+#endif
+ phys_cpu_present_map = physid_mask_of_physid(boot_cpu_physical_apicid);
+
+ setup_local_APIC();
+
+#ifdef CONFIG_X86_IO_APIC
+ if (smp_found_config)
+ if (!skip_ioapic_setup && nr_ioapics)
+ setup_IO_APIC();
+#endif
+ setup_boot_clock();
+
+ return 0;
+}
+
+/*
+ * APIC command line parameters
+ */
+static int __init parse_lapic(char *arg)
+{
+ enable_local_apic = 1;
+ return 0;
+}
+early_param("lapic", parse_lapic);
+
+static int __init parse_nolapic(char *arg)
+{
+ enable_local_apic = -1;
+ clear_bit(X86_FEATURE_APIC, boot_cpu_data.x86_capability);
+ return 0;
+}
+early_param("nolapic", parse_nolapic);
+
+static int __init parse_disable_lapic_timer(char *arg)
+{
+ local_apic_timer_disabled = 1;
+ return 0;
+}
+early_param("nolapic_timer", parse_disable_lapic_timer);
+
+static int __init parse_lapic_timer_c2_ok(char *arg)
+{
+ local_apic_timer_c2_ok = 1;
+ return 0;
+}
+early_param("lapic_timer_c2_ok", parse_lapic_timer_c2_ok);
+
+static int __init apic_set_verbosity(char *str)
+{
+ if (strcmp("debug", str) == 0)
+ apic_verbosity = APIC_DEBUG;
+ else if (strcmp("verbose", str) == 0)
+ apic_verbosity = APIC_VERBOSE;
+ return 1;
+}
+
+__setup("apic=", apic_set_verbosity);
+
+
+/*
+ * Local APIC interrupts
+ */
+
+/*
+ * This interrupt should _never_ happen with our APIC/SMP architecture
+ */
+void smp_spurious_interrupt(struct pt_regs *regs)
+{
+ unsigned long v;
+
+ irq_enter();
+ /*
+ * Check if this really is a spurious interrupt and ACK it
+ * if it is a vectored one. Just in case...
+ * Spurious interrupts should not be ACKed.
+ */
+ v = apic_read(APIC_ISR + ((SPURIOUS_APIC_VECTOR & ~0x1f) >> 1));
+ if (v & (1 << (SPURIOUS_APIC_VECTOR & 0x1f)))
+ ack_APIC_irq();
+
+ /* see sw-dev-man vol 3, chapter 7.4.13.5 */
+ printk(KERN_INFO "spurious APIC interrupt on CPU#%d, "
+ "should never happen.\n", smp_processor_id());
+ irq_exit();
+}
+
+/*
+ * This interrupt should never happen with our APIC/SMP architecture
+ */
+void smp_error_interrupt(struct pt_regs *regs)
+{
+ unsigned long v, v1;
+
+ irq_enter();
+ /* First tickle the hardware, only then report what went on. -- REW */
+ v = apic_read(APIC_ESR);
+ apic_write(APIC_ESR, 0);
+ v1 = apic_read(APIC_ESR);
+ ack_APIC_irq();
+ atomic_inc(&irq_err_count);
+
+ /* Here is what the APIC error bits mean:
+ 0: Send CS error
+ 1: Receive CS error
+ 2: Send accept error
+ 3: Receive accept error
+ 4: Reserved
+ 5: Send illegal vector
+ 6: Received illegal vector
+ 7: Illegal register address
+ */
+ printk (KERN_DEBUG "APIC error on CPU%d: %02lx(%02lx)\n",
+ smp_processor_id(), v , v1);
+ irq_exit();
+}
+
+/*
+ * Initialize APIC interrupts
+ */
+void __init apic_intr_init(void)
+{
+#ifdef CONFIG_SMP
+ smp_intr_init();
+#endif
+ /* self generated IPI for local APIC timer */
+ set_intr_gate(LOCAL_TIMER_VECTOR, apic_timer_interrupt);
+
+ /* IPI vectors for APIC spurious and error interrupts */
+ set_intr_gate(SPURIOUS_APIC_VECTOR, spurious_interrupt);
+ set_intr_gate(ERROR_APIC_VECTOR, error_interrupt);
+
+ /* thermal monitor LVT interrupt */
+#ifdef CONFIG_X86_MCE_P4THERMAL
+ set_intr_gate(THERMAL_APIC_VECTOR, thermal_interrupt);
+#endif
+}
+
+/**
+ * connect_bsp_APIC - attach the APIC to the interrupt system
+ */
+void __init connect_bsp_APIC(void)
+{
+ if (pic_mode) {
+ /*
+ * Do not trust the local APIC being empty at bootup.
+ */
+ clear_local_APIC();
+ /*
+ * PIC mode, enable APIC mode in the IMCR, i.e. connect BSP's
+ * local APIC to INT and NMI lines.
+ */
+ apic_printk(APIC_VERBOSE, "leaving PIC mode, "
+ "enabling APIC mode.\n");
+ outb(0x70, 0x22);
+ outb(0x01, 0x23);
+ }
+ enable_apic_mode();
+}
+
+/**
+ * disconnect_bsp_APIC - detach the APIC from the interrupt system
+ * @virt_wire_setup: indicates, whether virtual wire mode is selected
+ *
+ * Virtual wire mode is necessary to deliver legacy interrupts even when the
+ * APIC is disabled.
+ */
+void disconnect_bsp_APIC(int virt_wire_setup)
+{
+ if (pic_mode) {
+ /*
+ * Put the board back into PIC mode (has an effect only on
+ * certain older boards). Note that APIC interrupts, including
+ * IPIs, won't work beyond this point! The only exception are
+ * INIT IPIs.
+ */
+ apic_printk(APIC_VERBOSE, "disabling APIC mode, "
+ "entering PIC mode.\n");
+ outb(0x70, 0x22);
+ outb(0x00, 0x23);
+ } else {
+ /* Go back to Virtual Wire compatibility mode */
+ unsigned long value;
+
+ /* For the spurious interrupt use vector F, and enable it */
+ value = apic_read(APIC_SPIV);
+ value &= ~APIC_VECTOR_MASK;
+ value |= APIC_SPIV_APIC_ENABLED;
+ value |= 0xf;
+ apic_write_around(APIC_SPIV, value);
+
+ if (!virt_wire_setup) {
+ /*
+ * For LVT0 make it edge triggered, active high,
+ * external and enabled
+ */
+ value = apic_read(APIC_LVT0);
+ value &= ~(APIC_MODE_MASK | APIC_SEND_PENDING |
+ APIC_INPUT_POLARITY | APIC_LVT_REMOTE_IRR |
+ APIC_LVT_LEVEL_TRIGGER | APIC_LVT_MASKED );
+ value |= APIC_LVT_REMOTE_IRR | APIC_SEND_PENDING;
+ value = SET_APIC_DELIVERY_MODE(value, APIC_MODE_EXTINT);
+ apic_write_around(APIC_LVT0, value);
+ } else {
+ /* Disable LVT0 */
+ apic_write_around(APIC_LVT0, APIC_LVT_MASKED);
+ }
+
+ /*
+ * For LVT1 make it edge triggered, active high, nmi and
+ * enabled
+ */
+ value = apic_read(APIC_LVT1);
+ value &= ~(
+ APIC_MODE_MASK | APIC_SEND_PENDING |
+ APIC_INPUT_POLARITY | APIC_LVT_REMOTE_IRR |
+ APIC_LVT_LEVEL_TRIGGER | APIC_LVT_MASKED);
+ value |= APIC_LVT_REMOTE_IRR | APIC_SEND_PENDING;
+ value = SET_APIC_DELIVERY_MODE(value, APIC_MODE_NMI);
+ apic_write_around(APIC_LVT1, value);
+ }
+}
+
+/*
+ * Power management
+ */
+#ifdef CONFIG_PM
+
+static struct {
+ int active;
+ /* r/w apic fields */
+ unsigned int apic_id;
+ unsigned int apic_taskpri;
+ unsigned int apic_ldr;
+ unsigned int apic_dfr;
+ unsigned int apic_spiv;
+ unsigned int apic_lvtt;
+ unsigned int apic_lvtpc;
+ unsigned int apic_lvt0;
+ unsigned int apic_lvt1;
+ unsigned int apic_lvterr;
+ unsigned int apic_tmict;
+ unsigned int apic_tdcr;
+ unsigned int apic_thmr;
+} apic_pm_state;
+
+static int lapic_suspend(struct sys_device *dev, pm_message_t state)
+{
+ unsigned long flags;
+ int maxlvt;
+
+ if (!apic_pm_state.active)
+ return 0;
+
+ maxlvt = lapic_get_maxlvt();
+
+ apic_pm_state.apic_id = apic_read(APIC_ID);
+ apic_pm_state.apic_taskpri = apic_read(APIC_TASKPRI);
+ apic_pm_state.apic_ldr = apic_read(APIC_LDR);
+ apic_pm_state.apic_dfr = apic_read(APIC_DFR);
+ apic_pm_state.apic_spiv = apic_read(APIC_SPIV);
+ apic_pm_state.apic_lvtt = apic_read(APIC_LVTT);
+ if (maxlvt >= 4)
+ apic_pm_state.apic_lvtpc = apic_read(APIC_LVTPC);
+ apic_pm_state.apic_lvt0 = apic_read(APIC_LVT0);
+ apic_pm_state.apic_lvt1 = apic_read(APIC_LVT1);
+ apic_pm_state.apic_lvterr = apic_read(APIC_LVTERR);
+ apic_pm_state.apic_tmict = apic_read(APIC_TMICT);
+ apic_pm_state.apic_tdcr = apic_read(APIC_TDCR);
+#ifdef CONFIG_X86_MCE_P4THERMAL
+ if (maxlvt >= 5)
+ apic_pm_state.apic_thmr = apic_read(APIC_LVTTHMR);
+#endif
+
+ local_irq_save(flags);
+ disable_local_APIC();
+ local_irq_restore(flags);
+ return 0;
+}
+
+static int lapic_resume(struct sys_device *dev)
+{
+ unsigned int l, h;
+ unsigned long flags;
+ int maxlvt;
+
+ if (!apic_pm_state.active)
+ return 0;
+
+ maxlvt = lapic_get_maxlvt();
+
+ local_irq_save(flags);
+
+ /*
+ * Make sure the APICBASE points to the right address
+ *
+ * FIXME! This will be wrong if we ever support suspend on
+ * SMP! We'll need to do this as part of the CPU restore!
+ */
+ rdmsr(MSR_IA32_APICBASE, l, h);
+ l &= ~MSR_IA32_APICBASE_BASE;
+ l |= MSR_IA32_APICBASE_ENABLE | mp_lapic_addr;
+ wrmsr(MSR_IA32_APICBASE, l, h);
+
+ apic_write(APIC_LVTERR, ERROR_APIC_VECTOR | APIC_LVT_MASKED);
+ apic_write(APIC_ID, apic_pm_state.apic_id);
+ apic_write(APIC_DFR, apic_pm_state.apic_dfr);
+ apic_write(APIC_LDR, apic_pm_state.apic_ldr);
+ apic_write(APIC_TASKPRI, apic_pm_state.apic_taskpri);
+ apic_write(APIC_SPIV, apic_pm_state.apic_spiv);
+ apic_write(APIC_LVT0, apic_pm_state.apic_lvt0);
+ apic_write(APIC_LVT1, apic_pm_state.apic_lvt1);
+#ifdef CONFIG_X86_MCE_P4THERMAL
+ if (maxlvt >= 5)
+ apic_write(APIC_LVTTHMR, apic_pm_state.apic_thmr);
+#endif
+ if (maxlvt >= 4)
+ apic_write(APIC_LVTPC, apic_pm_state.apic_lvtpc);
+ apic_write(APIC_LVTT, apic_pm_state.apic_lvtt);
+ apic_write(APIC_TDCR, apic_pm_state.apic_tdcr);
+ apic_write(APIC_TMICT, apic_pm_state.apic_tmict);
+ apic_write(APIC_ESR, 0);
+ apic_read(APIC_ESR);
+ apic_write(APIC_LVTERR, apic_pm_state.apic_lvterr);
+ apic_write(APIC_ESR, 0);
+ apic_read(APIC_ESR);
+ local_irq_restore(flags);
+ return 0;
+}
+
+/*
+ * This device has no shutdown method - fully functioning local APICs
+ * are needed on every CPU up until machine_halt/restart/poweroff.
+ */
+
+static struct sysdev_class lapic_sysclass = {
+ set_kset_name("lapic"),
+ .resume = lapic_resume,
+ .suspend = lapic_suspend,
+};
+
+static struct sys_device device_lapic = {
+ .id = 0,
+ .cls = &lapic_sysclass,
+};
+
+static void __devinit apic_pm_activate(void)
+{
+ apic_pm_state.active = 1;
+}
+
+static int __init init_lapic_sysfs(void)
+{
+ int error;
+
+ if (!cpu_has_apic)
+ return 0;
+ /* XXX: remove suspend/resume procs if !apic_pm_state.active? */
+
+ error = sysdev_class_register(&lapic_sysclass);
+ if (!error)
+ error = sysdev_register(&device_lapic);
+ return error;
+}
+device_initcall(init_lapic_sysfs);
+
+#else /* CONFIG_PM */
+
+static void apic_pm_activate(void) { }
+
+#endif /* CONFIG_PM */